Loading...
HomeMy WebLinkAboutMERCER PARK PLAYGROUND REPLACEMENT PROJECT/2015MERCER PARK PLAYGROUND REPLACEMENT PROJECT/2015 -- M P—C�c.�� C, k_ -PLcu-� q ro Lc kk� rb Co -Mkt -A 5 ._c.._- .r u fo I [ L �` Ae 0. -' J -2Q - C�� 1'S�s � 5 - ��� � GL(a �rz;•/i• K Q � I�eLS_, s�c_S , -. IO-A�v v D -QLD ✓ ��� t- _ __ In -e ll _- ik", srarIDEV, CITY OF IOWA CITY, -:� � -�-, Y� -4 C" �� rn s DEPARTMENT OF PUBLIC WORKS ENGINEERING DIVISION PLANS, SPECIFICATIONS, PROPOSAL AND CONTRACT FOR THE MERCER PARK PLAYGROUND REPLACMENT PROJECT IOWA CITY, IOWA I hereby certify that this engineering document was prepared by me or under my direct personal supervision and that I am a duly licensed Professional Engineer under the laws of the State of Iowa. SIGNED: DATE: Scott K. Sovers, P.E. Senior Civil Engineer Iowa Reg. No. 17141 My license renewal date is December 31, 2015, SPECIFICATIONS TABLE OF CONTENTS TITLE SHEET TABLE OF CONTENTS Pape Number NOTICE TO BIDDERS............................................................................................ AF -1 NOTE TO BIDDERS............................................................................................... NB -1 FORM OF PROPOSAL........................................................................................... FP -1 BIDBOND............................................................................................................... BB -1 FORM OF AGREEMENT........................................................................................ AG -1 PERFORMANCE AND PAYMENT BOND.............................................................. PB -1 CONTRACT COMPLIANCE (ANTI -DISCRIMINATION REQUIREMENTS)................................................... CC -1 GENERAL CONDITIONS........................................................................................ GC -1 SUPPLEMENTARY CONDITIONS......................................................................... SC -1 BIDDER STATUS FORM........................................................................................ BF -1 TECHNICAL SECTION DIVISION 1 - GENERAL REQUIREMENTS Section 01010 Summary of the Work ......................................................... 01010-1 Section 01025 Measurement and Payment ................................................ 01025-1 Section 01310 Progress and Schedules..................................................... 01310-1 DIVISION 2 - SITE WORK Section 02900 Landscaping........................................................................ 02900-1 Section 03500 Materials.............................................................................. 03500-1 Section 03600 Installation........................................................................... 03600-1 ti O -�.ry C i -<r-. y z- NOTICE TO BIDDERS MERCER PARK PLAYGROUND REPLACEMENT PROJECT Sealed proposals will be received by the City Clerk of the City of Iowa City, Iowa, until 2:30 P.M. on the 4th day of November, 2015. Sealed proposals will be opened immediately thereafter by the City Engineer or designee. Bids submitted by fax machine shall not be deemed a "sealed bid" for purposes of this Project. Proposals received after this deadline will be returned to the bidder unopened. Proposals will be acted upon by the City Council at a meeting to be held in the Emma J. Harvat Hall at 7:00 P.M. on the 10th day of November, 2015, or at special meeting called for that purpose. The Project will involve the following: The supply and installation of new playground equipment in replacement of the existing equipment located at Mercer Park. All work is to be done in strict compliance with the plans and specifications prepared by Outdoor Recreation Products, of Ames, Iowa and the City of Iowa City, which have heretofore been approved by the City Council, and are on file for public examination in the Office of the City Clerk. Each proposal shall be completed on a form furnished by the City and must be accompanied in a sealed envelope, separate from the one containing the proposal, by a bid bond executed by a corporation authorized to contract as a surety in the State of Iowa, in the sum of 10% of the bid. The bid security shall be made payable to the TREASURER OF THE CITY OF IOWA CITY, IOWA, and shall be forfeited to the City of Iowa City in the event the successful bidder fails to enter into a contract within ten (10) calendar days of the City Council's award of the contract and post bond satisfactory to the City ensuring the faithful performance of the contract and mainte- nance of said Project, if required, pursuant to the provisions of this notice and the other contract documents. Bid bonds of the lowest two or more bidders may be retained for a period of not to exceed fifteen (15) calendar days following award of the contract, or until rejection is made. Other bid bonds will be returned after the canvass and tabulation of bids is completed and reported to the City Council. The successful bidder will be required to furnish a bond in an amount equal to one hundred percent (100%) of the contract price, said bond to be issued by a responsible surety approved by the AF -1 N o _ C cn c-� o r` t^� a �a m City, and shall guarantee the prompt payment of all materials and labor, and also protect and save harmless the City from all claims and damages of any kind caused directly or indirectly by the operation of the contract, and shall also guarantee the maintenance of the improvement for a period of one (1) year from and after its completion and formal acceptance by the City Council. The following limitations shall apply to this Project: Specified Start Date: November 23rd. 2015 Completion Date: May 13.2016 Liquidated Damages: $100.00 per day The plans, specifications and proposed contract documents may be examined at the office of the City Clerk. Copies of said plans and specifications and form of proposal blanks may be secured at the Office of City Engineer of Iowa City 410 East Washington Street, Iowa City, Iowa, by bona fide bidders. A $50 refundable fee is required for each set of plans and specifications provided to bidders or other interested persons. The fee shall be in the form of a check, made payable to the City of Iowa City. A refund will be issued if re -useable plans and specifications are returned to the City of Iowa City within 14 days of the project award date. Prospective bidders are advised that the City of Iowa City desires to employ minority contractors and subcontractors on City projects. A listing of minority contractors can be obtained from the Iowa Department of Inspections and Appeals at (515) 281-5796 and the Iowa Department of Transportation Contracts Office at (515) 239- 1422. Bidders shall list on the Form of Proposal the names of persons, firms, companies or other parties with whom the bidder intends to subcon- tract. This list shall include the type of work and approximate subcontract amount(s). The Contractor awarded the contract shall submit a list on the Form of Agreement of the proposed subcontractors, together with quantities, unit prices and extended dollar amounts. By virtue of statutory authority, preference must be given to products and provisions grown and coal produced within the State of Iowa, and to Iowa domestic labor, to the extent lawfully re- quired under Iowa Statutes. The Iowa reciprocal resident bidder preference law applies to this Project. The City reserves the right to reject any or all proposals, and also reserves the right to waive technicalities and irregularities. Published upon order of the City Council of Iowa City, Iowa. MARIAN K. KARR, CITY CLERK N 0 < rn = r� rn CD �r o v - W NOTE TO BIDDERS 1. The successful bidder and all subcontractors are required to submit at least 4 days prior to award three references involving similar projects, including at least one municipal reference. Award of the bid or use of specific subcontractors may be denied if sufficient favorable references are not verified or may be denied based on past experience on projects with the City of Iowa City. 2. References shall be addressed to the City Engineer and include the name, address and phone number of the contact person, for City verification. 3. Bid submittals are: Envelope 1: Envelope 2: Envelope 3: Bid Bond Form of Proposal Bidder Status Form IMS N _O �_ Cn Cn Irl a M in e � C71 FORM OF PROPOSAL MERCER PARK PLAYGROUND REPLACEMENT PROJECT CITY OF IOWA CITY NOTICE TO BIDDERS: PLEASE DO NOT USE THE FORM OF PROPOSAL INCLUDED IN THE BOUND VOLUME OF THE SPECIFICATIONS. SEPARATE COPIES OF THIS PROPOSAL ARE CONTAINED WITHIN THE BACK COVER OF THIS DOCUMENT. Name of Bidder Address of Bidder TO: City Clerk City of Iowa City City Hall 410 E. Washington St. Iowa City, IA 52240 The undersigned bidder submits herewith bid security in the amount of $ , in accordance with the terms set forth in the 'Project Specifications." The undersigned bidder, having examined and determined the scope of the Contract Documents, hereby proposes to provide the required labor, services, materials and equipment and to perform the Project as described in the Contract Documents, including Addenda , and , and to do all work at the prices set forth herein. N We further propose to do all "Extra Work" which may be required to Lomplew the work contemplated, at unit prices or lump sums to be agreed upon in writing prior to *ttogiwch we- �n qqTT## ESTIMATED UNIT='mEATENDED' ITEM DESCRIPTION UNIT QUANTITY PRICE AhAOUt T� 1 Supply and Install LS 1 4� Playground Equipment $ $ TOTAL EXTENDED AMOUNT = FP -1 The names of those persons, firms, companies or other parties with whom we intend to enter into a subcontract, together with the type of subcontracted work and approximate dollar amount of the subcontract, are as follows: NOTE: All subcontractors are subject to approval by City. The undersigned bidder certifies that this proposal is made in good faith, and without collusion or connection with any other person or persons bidding on the work. The undersigned bidder states that this proposal is made in conformity with the Contract Documents and agrees that, in the event of any discrepancies or differences between any conditions of this proposal and the Contract Documents prepared by the City of Iowa City, the more specific shall prevail. Firm: Signature: Printed Name: Title: Address: Phone: N n Contact:f " o ��-- :<ra M M �xs x a F aN FP -2 as Principal, and as Surety declare that we are held and are firmly bound unto the City of Iowa City, Iowa, hereinafter called "OWNER," in the sum of Dollars to pay said sum as herein provided. We as Principal and Surety further promise and declare that these obligations shall bind our heirs, executors, administrators, and successors jointly and severally. This obligation is conditioned on the Principal submission of the accompanying bid, dated the Mercer Park Playground Replacement Project. NOW, THEREFORE, (a) If said Bid shall be rejected, or in the alternate, for (b) If said Bid shall be accepted and the Principal shall execute and deliver a contract in the form specified, and the Principal shall then furnish a bond for the Principal's faithful performance of said Project, and for the payment of all persons performing labor or furnishing materials in connection therewith, and shall in all other respects perform the Project, as agreed to by the City's acceptance of said Bid, then this obligation shall be void. Otherwise this obligation shall remain in full force and effect, provided that the liability of the Surety for any and all claims hereunder shall, in no event, exceed the amount of the obligation stated herein. o�� o ' n By virtue of statutory authority, the full amount of this bid bond shall orfeifed ter -M, Owner in the event that the Principal fails to execute the contract and prowl th j,bon4, as provided in the Project specifications or as required by law. ::4 C-) (1j j <rn = The Surety, for value received, hereby stipulates and agrees that the 6QQMions of SdTd Surety and its bond shall in no way be impaired or affected by any extension 5Df the tiaae within which the Owner may accept such Bid or may execute such contract documents, and swd Surety does hereby waive notice of any such time extension. The Principal and the Surety hereto execute this bid bond this day of A.D., 20 (Seal) Witness Principal By (Title) (Seal) Surety By Witness (Attorney-in-fact) Attach Power -of -Attorney FORM OF AGREEMENT THIS AGREEMENT is made and entered into by and between the City of Iowa City, Iowa ("City"), and ("Contractor"). Whereas the City has prepared certain plans, specifications, proposal and bid documents dated the day of , 20_, for the Mercer Park Playground Replacement Project ('Project"), and Whereas, said plans, specifications, proposal and bid documents accurately and fully describe the terms and conditions upon which the Contractor is willing to perform the Project. NOW, THEREFORE, IT IS AGREED: The City hereby accepts the attached proposal and bid documents of the Contractor for the Project, and for the sums listed therein. 2. This Agreement consists of the following component parts which are incorporated herein by reference: a. Addenda Numbers b. "Standard Specifications for Highway and Bridge Construction," Series of 2012, Iowa Department of Transportation, as amended, C. Plans; d. Specifications and Supplementary Conditions, e. Notice to Bidders; f. Note to Bidders, g. Performance and Payment Bond; h. Bidder Status Form; 0 i. Contract Compliance Program (Anti -Discrimination Regt]er"; s {j j. Proposal and Bid Documents; and =f�� k. This Instrument. _r" �'-. The above components are deemed complementary and should be read tog4w. In the M event of a discrepancy or inconsistency, the more specific provision shall prevail. AG -1 3. The names of subcontractors approved by City, together with quantities, unit prices, and extended dollar amounts, are as follows (or shown on an attachment): 4. Payments are to be made to the Contractor in accordance with the Supplementary Conditions. DATED this day of , 20_ City ATTEST: Mayor Contractor City Clerk (Company Official) AG -2 Approved By: City Attorney's Office N O By n 9 -v-a �i y� —a (Title) � Q ATTEST: ©x w City Clerk (Company Official) AG -2 Approved By: City Attorney's Office PERFORMANCE AND PAYMENT BOND as (insert the name and address or legal title of the Contractor) Principal, hereinafter called the Contractor and (insert the legal title of the Surety) as Surety, hereinafter called the Surety, are held and firmly bound unto the City of Iowa City, Iowa, as obligee, hereinafter called the Owner, in the amount of Dollars for the payment for which Contractor and Surety hereby bind themselves, their heirs, executors, administrators, successors and assigns, jointly and severally. WHEREAS, Contractor has, as of entered into a (date) written Agreement with Owner for the Mercer Park Playground Replacement -Project; and WHEREAS, the Agreement requires execution of this Performance and Payment Bond, to be completed by Contractor, in accordance with plans and specifications prepared by the City of Iowa City, which Agreement is by reference made a part hereof, and the agreed-upon work is hereafter referred to as the Project. NOW, THEREFORE, THE CONDITIONS OF THIS OBLIGATION are such that, if Contractor shall promptly and faithfully perform said Agreement, then the obligation of this bond shall be null and void, otherwise it shall remain in full force and effect until satisfactory completion of the Project. A. The Surety hereby waives notice of any alteration or extension of time made by the 0 Owner. e o ZF t B. Whenever Contractor shall be, and is declared by Owner to be, in It �der4W Agreement, the Owner having performed Owners obligations thereunde t#Ze STety rhe Cr` a M promptly remedy the default, or shall promptly: c-- 1. Complete the Project in accordance with the terms and c� Jiiiionf of the r Agreement, or 2. Obtain a bid or bids for submission to Owner for completing the Project in accordance with the terms and conditions of the Agreement; and upon determina- tion by Owner and Surety of the lowest responsible bidder, arrange for a contract between such bidder and Owner, and make available, as work progresses (even though there may be a default or a succession of defaults under the Agreement or subsequent contracts of completion arranged under this paragraph), sufficient 9a funds to pay the cost of completion, less the balance of the Contract Price, but not exceeding the amount set forth in the first paragraph hereof. The term "balance of the Contract Price," as used in this paragraph, shall mean the total amount payable by Owner to Contractor under the Agreement, together with any addenda and/or amendments thereto, less the amount properly paid by Owner to Contractor. C. The Contractor and Contractor's Surety shall be obligated to keep the improvements covered by this bond in good repair for a period of one (1) year from the date of formal acceptance of the improvements by the Owner. D. No right of action shall accrue to or for the use of any person, corporation or third party other than the Owner named herein or the heirs, executors, administrators or successors of Owner. IT IS A FURTHER CONDITION OF THIS OBLIGATION that the Principal and Surety, in accordance with provisions of Chapter 573, Code of Iowa, shall pay to all persons, firms or corporations having contracts directly with the Principal, including any of Principal's subcontrac- tors, all claims due them for labor performed or materials furnished in the performance of the Agreement for whose benefit this bond is given. The provisions of Chapter 573, Code of Iowa, are a part of this bond to the same extent as if it were expressly set out herein. r.� SIGNED AND SEALED THIS DAY OF , IN THE PRESENCE OF: Witness Witness am (Principal)_ o o ��• `^ o� —n D.4 -� (Title) c) m r �r GM v M (Surety) o w (Title) (Street) (City, State, Zip) (Phone) Contract Compliance Program 1 r 1 � �• A*Z,A J� a CITY OF IOWA CITY SECTION I - GENERAL POLICY STATEMENT It is the policy of the City of Iowa City to require equal employment opportunity in all City contract work. This policy prohibits discrimination by the City's contractors, consultants and vendors and requires them to ensure that applicants seeking employment with them and their employees are treated equally without regard to race, color, creed, religion, national origin, sex, gender identity, sexual orientation, disability, marital status, and age. It is the City's intention to assist employers, who are City contractors, vendors or consultants, in designing and implementing equal employment opportunity so that all citizens will be afforded equal accessibility and opportunity to gain and maintain employment. PROVISIONS: All contractors, vendors, and consultants requesting to do business with the City must submit an Equal Opportunity Policy Statement before the execution of the contract. 2. All City contractors, vendors, and consultants with contracts of $25,000 or more (or less if required by another governmental agency) must abide by the requirements of the City's Contract Compliance Program. Emergency contracts may be exempt from this provision at the discretion of the City. Regardless of the value of the contract, all contractors, vendors, and consultants are subject to the City's Human Rights Ordinance, which is coded at Article 2 of the City Code. 3. Contracting departments are responsible for assuring that City contractors, vendors, and consultants are made aware of the City's Contract Compliance Program reporting responsibilities and receive the appropriate reporting forms. A notification of requirements will be included in any request for proposal and notice of bids. 4. Prior to execution of the contract, the completed and signed Assurance of Compliance (located on pages CC -2 and CC -3) or other required material must be received and approved by the City. 5. Contracting departments are responsible for answering questions about contractor, consultant and vendor compliance during the course of the contract with the City. N O 6. All contractors, vendors, and consultants must refrain from the use of any�igs (gdesi ions which are sexist in nature, such as those which state "Men Working" or '�agm�Ahead,ll and instead use gender neutral signs. =i n m 7. All contractors, vendors, and consultants must assure that their subcon-1g—oorbid the City's Human Rights Ordinance. The City's protected classes are listed aV1§�va 8ty Code section 2-3-1. y w mgr\asst\contractcomplianc doc CC -1 SECTION II - ASSURANCE OF COMPLIANCE The following sets forth the minimum requirements of a satisfactory Equal Employment Opportunity Program which will be reviewed for acceptability. PLEASE RETURN PAGES 2 THROUGH 3 OF THIS SECTION TO THE CONTRACTING DEPARTMENT PRIOR TO THE EXECUTION OF THE CONTRACT. With respect to the performance of this contract, the contractor, consultant or vendor agrees as follows: (For the purposes of these minimum requirements, "contractor" shall include consultants and vendors.) The contractor will not discriminate against any employee or applicant for employment and will take affirmative efforts to ensure applicants and employees are treated during employment without regard to their race, color, creed, religion, national origin, sex, sexual orientation, gender identity, disability, marital status, and age. Such efforts shall include, but not be limited to the following: employment, promotion, demotion, or transfer; recruitment or recruitment advertising; layoff or termination; rates of pay or other forms of compensation; and selection for training, including apprenticeship. 2. The contractor will, in all solicitations or advertisements for employees placed by or on behalf of the contractor, state that it is an equal opportunity employer. Note: Contracts that are federally funded are subject to Executive Order No. 11246, as amended, and the regulations (see generally 29 U.S.C. § 1608 et sem.) and relevant orders of the U.S. Secretary of Labor. The Secretary of Labor, and not the City, enforces said regulations and orders. 3. Provide a copy of your written Equal Employment Opportunity policy statement. Where is this statement posted? 4. What is the name, telephone number and address of your business' Equal Employment Opportunity Officer? (Please print) Phone number Address N O 5. The undersigned agrees to display, in conspicuous places at the work sit(, --all pcWers required by federal and state law for the duration of the contract. NOTE: The City csprpro\qe asS"nce in obtaining the necessary posters. —4 C � --- �-` M �� t0 m mg r\asst\co ntractcom plia nce. doc CC -2 6. How does your business currently inform applicants, employees, and recruitment sources (including unions) that you are an Equal Employment Opportunity employer? The above responses to questions 1 through 6, are true and correctly reflect our Equal Employment Opportunity policies. Business Name Signature Phone Number Title Print Name Date mghassftontractcomplianc .doc CC -3 N O O Vt C1 1 rr+i a rn E;� s o n - w mghassftontractcomplianc .doc CC -3 SECTION III - SUGGESTED STEPS TO ASSURE EQUAL EMPLOYMENT OPPORTUNITIES COMPANY POLICY Determine your company's policy regarding equal employment opportunities. Document the policy and post it in a conspicuous place so that it is known to all your employees. Furthermore, disseminate the policy to all potential sources of employees and to your subcontractors asking their cooperation. The policy statement should recognize and accept your responsibility to provide equal employment opportunity in all your employment practices. In regard to dissemination of this policy, this can be done, for example, through the use of letters to all recruitment sources and subcontractors, personal contacts, employee meetings, web page postings, employee handbooks, and advertising. 2. EQUAL EMPLOYMENT OPPORTUNITY OFFICER Designate an equal employment opportunity officer or, at minimum, assign someone the responsibility of administering and promoting your company's Equal Employment Opportunity program. This person should have a position in your organization which emphasizes the importance of the program. 3. INSTRUCT STAFF Your staff should be aware of and be required to abide by your Equal Employment Opportunity program. All employees authorized to hire, supervise, promote, or discharge employees or are involved in such actions should be trained and required to comply with your port and!5e current equal employment opportunity laws., o xv - _ 4. RECRUITMENT ' rn (a) Let potential employees know you are an equal opportunity emplo-% hKcanrNdone by identifying yourself on all recruitment advertising as "an equal opportu Ambi gyer (b) Use recruitment sources that are likely to yield diverse applicdri: pooli Word-of-mouth recruitment will only perpetuate the current composition of your workforcea.�Send recruitment sources a letter annually which reaffirms your commitment to equal employment opportunity and requests their assistance in helping you reach diverse applicant pools. (c) Analyze and review your company's recruitment procedures to identify and eliminate discriminatory barriers. (d) Select and train persons involved in the employment process to use objective standards and to support equal employment opportunity goals. (e) Review periodically job descriptions to make sure they accurately reflect major job functions. Review education and experience requirements to make sure they accurately reflect the requirements for successful job performance. (f) Review the job application to insure that only job related questions are asked. Ask yourself "Is this information necessary to judge an applicant's ability to perform the job applied for?" Only use job-related tests which do not adversely affect any particular group of people. (g) Monitor interviews carefully. Prepare interview questions in advance to assure that they are only job related. Train your interviewers on discrimination laws. Biased and subjective judgments in personal interviews can be a major source of discrimination. (h) Improve hiring and selection procedures and use non -biased promotion, transfer and training policies to increase and/or improve the diversity of your workforce representation. Companies must make sure procedures for selecting candidates for promotion, transfer and training are based upon a fair assessment of an employee's ability and work record. Furthermore, all companies should post and otherwise publicize all job promotional opportunities and encourage all qualified employees to bid on them. 12/01 mgAassftonlractcompliance.doc CC -4 Attached for your information is a copy of Section 2 — 3 — 1 of the Iowa City Code of Ordinances which prohibits certain discriminatory practices in employment. Please note that the protected characteristics include some not mandated for protection by Federal or State law. As a contractor, consultant or vendor doing business with the City of Iowa City you are required to abide by the provisions of the local ordinance in conjunction with your performance under a contract with the City. CC -5 N O O CD C-) r �� rn w CC -5 2-3-1: EMPLOYMENT; EXCEPTIONS: A. It shall be unlawful for any employer to refuse to hire, accept, register, classify, promote or refer for employment, or to otherwise discriminate in employment against any other person or to discharge any employee because of age, color, creed, disability, gender identity, marital status, national origin, race, religion, sex or sexual orientation. (Ord. 03-4105, 12-16-2003) B. It shall be unlawful for any labor organization to refuse to admit to membership, apprenticeship or training an applicant, to expel any member, or to otherwise discriminate against any applicant for membership, apprenticeship or training or any member in the privileges, rights or benefits of such membership, apprenticeship or training because of age, color, creed, disability, gender identity, marital status, national origin, race, religion, sex or sexual orientation of such applicant or member. C. It shall be unlawful for any employer, employment agency, labor organization or the employees or members thereof to directly or indirectly advertise or in any other manner indicate or publicize that individuals are unwelcome, objectionable or not solicited for employment or membership because of age, color, creed, disability, gender identity, marital status, national origin, race, religion, sex or sexual orientation. (Ord. 95-3697, 11-7-1995) D. Employment policies relating to pregnancy and childbirth shall be governed by the following: 1. A written or unwritten employment policy or practice which excludes from employment applicants or employees because of the employee's pregnancy is a prima facie violation of this title. 2. Disabilities caused or contributed to by the employee's pregnancy, miscarriage, childbirth and recovery therefrom are, for all job related purposes, temporary disabilities and shall be treated as such under any health or temporary disability insurance or sick leave plan available in connection with employment or any written or unwritten employment policies and practices involving terms and conditions of employment as applied to other temporary disabilities. E. It shall be unlawful for any person to solicit or require as a condition of employment of any employee or prospective employee a test for the presence of the antibody to the human immunodeficiency virus. An agreement between an employer, employment agency, labor organization or their employees, agents or members and an employee or prospective employee concerning employment, pay or benefits to an employee or prospective employee in return for taking a test for the presence of the antibody to the human immunodeficiency virus, is prohibited. The prohibitions of this subsection do not apply if the state epidemiologist determines and the director of public health declares through the utilization of guidelines established by the center for disease control of the United States department of health and human services, that a person with a condition related to acquired immune deficiency syndrome poses a significant risk of transmission of the human immunodeficiency virus to other persons in a specific occupation. 0 ¢6 �„ F. The following are exempted from the provisions of this section: T7 n� r � "r67 rn :�rq � M CC -6 rn 1. Any bona fide religious institution or its educational facility, association, corporation or society with respect to any qualifications for employment based on religion when such qualifications are related to a bona fide religious purpose. A religious qualification for instructional personnel or an administrative officer, serving in a supervisory capacity of a bona fide religious educational facility or religious institution shall be presumed to be a bona fide occupational qualification. (Ord. 94-3647, 11-8-1994) 2. An employer or employment agency which chooses to offer employment or advertise for employment to only the disabled or elderly. Any such employment or offer of employment shall not discriminate among the disabled or elderly on the basis of age, color, creed, disability, gender identity, marital status, national origin, race, religion, sex or sexual orientation. (Ord. 95- 3697, 11-7-1995) 3. The employment of individuals for work within the home of the employer if the employer or members of the family reside therein during such employment. 4. The employment of individuals to render personal service to the person of the employer or members of the employer's family. (Ord. 94-3647, 11-8-1994) 5. The employment on the basis of sex in those certain instances where sex is a bona fide occupational qualification reasonably necessary to the normal operation of a particular business or enterprise. The bona fide occupational qualification shall be interpreted narrowly. (Ord. 03- 4105, 12-16-2003) 6. A state or federal program designed to benefit a specific age classification which serves a bona fide public purpose. (Ord. 94-3647, 11-8-1994) 7. The employment on the basis of disability in those certain instances where presence of disability is a bona fide occupational qualification reasonably necessary to the normal operation of a particular business or enterprise. The bona fide occupational qualification shall be interpreted narrowly. (Ord. 03-4105, 12-16-2003) 8. Any employer who regularly employs less than four (4) individuals. For purposes of this section, individuals who are members of the employer's family shall not be counted as employees. (Ord. 08-4312, 8-11-2008) CC -7 N O O V1 Oc i M <rn a m � 3 Q D _ w CC -7 SAMPLE: EQUAL EMPLOYMENT OPPORTUNITY POLICY To all employees of This Company and its employees shall not discriminate against any employee or applicant for employment based on his or her age, color, creed, disability, national origin, gender identity, marital status, race, religion, sex, or sexual orientation. The anti -discrimination policy extends to decisions involving hiring, promotion, demotion, or transfer; recruitment or recruitment advertising; layoff or termination, rates of pay or other forms of compensation; and selection for training, including apprenticeship. Further, this Company and its employees will provide a working environment free from such discrimination. All employees are encouraged to refer minority and women applicants and applicants with disabilities for employment. The Equal Employment Opportunity Officer for the is: Name: Address: Telephone Number: NOTE: This is a SAMPLE ONLY. You may wish to confer with your EEO officer or legal counsel to formulate a policy which specifically meets the needs of your company. CC -8 H 4r `i M da �\ �Y r !?1 CC -8 GENERAL CONDITIONS Division 11, General Requirements and Covenants of the Iowa Department of Transportation "Standard Specifications for Highway and Bridge Construction," Series of 2012, as amended, shall apply except as amended in the Supplementary Conditions. o� o D 4 n� m crn rn a m= o n _ GC -1 SUPPLEMENTARY CONDITIONS ARTICLES WITHIN THIS SECTION S-1 Definitions S-2 Limitations of Operations S-3 Insurance S4 Supervision and Superintendence S-5 Concerning Subcontractors, Suppliers and Others S-6 Compliance with OSHA Regulations S-7 Employment Practices S-8 Contract Compliance Program (Anti -Discrimination Requirements) S-9 Measurement and Payment S-10 Taxes S-11 Construction Stakes S-12 Restriction on Non -Resident Bidding on Non -Federal -Aid Projects Caption and Introductory Statements These Supplementary Conditions amend or supplement Division 11 of the Iowa Department of Transportation "Standard Specifications for Highway and Bridge Construction," Series of 2012, as amended and other provisions of the Contract Documents. All provisions which are not so amended or supplemented remain in full force and effect. S-1 DEFINITIONS. ADD to or CHANGE the following definitions within 1101.03 of the IDOT STANDARD SPECIFICATIONS. "ENGINEER" shall mean the Director of Public Works for the City of Iowa City, Iowa or his authorized representative. "OWNER" and "CITY" shall mean the City of Iowa City, Iowa acting through the City Council and duly authorized agents. "CONTRACTING AUTHORITY," "DEPARTMENT OF TRANSPORTATION," or "COUNTY" shall mean the CITY. "IDOT STANDARD SPECIFICATIONS" shall mean the Iowa Department of TraZportation "Standard Specifications for Highway and Bridge Construction," Sedps offM012, as amended. ell o C-3 �I S-2 LIMITATIONS OF OPERATIONS. r -- Add the following paragraph to 1108.03 of the IDOT STANDARD SPECIFICATIS 'T rn Except for such work as may be required to properly maintain lights and barricadgs, no work will be permitted on Sundays or legal holidays without specific permission of the ENGINEER. SC -1 S-3 INSURANCE. A. CERTIFICATE OF INSURANCE: CANCELLATION OR MODIFICATION Before commencing work, the Contractor shall submit to the City for approval a Certificate of Insurance, meeting the requirements specified herein, to be in effect for the full contract period. The name, address and phone number of the insurance company and agent must accompany the certificate. The liability limits required hereunder must apply to this Project only. 2. The Contractor shall notify the City in writing at least thirty (30) calendar days prior to any change or cancellation of said policy or policies. 3. Cancellation or modification of said policy or policies shall be considered just cause for the City of Iowa City to immediately cancel the contract and/or to halt work on the contract, and to withhold payment for any work performed on the contract. B. MINIMUM COVERAGE Any policy or policies of insurance purchased by the Contractor to satisfy his/her responsibilities under this contract shall include contractual liability coverage, and shall be in the following type and minimum amounts: Type of Coverage Comprehensive General Liability Bodily Injury & Property Damage* Automobile Liability Bodily Injury & Property Damage Excess Liability Each Occurrence Anaregate $1,000,000 $2,000,000 Combined Single Limit $1,000,000 $1,000,000 $1,000,000 Worker's Compensation Insurance as required by Chapter 85, Code of Iowa. *Property Damage liability insurance must provide explosion, collapse and underground coverage when determined by City to be applicable. o_ D `^ The City requires that the Contractor's Insurance carrier be A rated or better by eF5 M rn a 0 w SC -2 In addition, the Contractor shall be required to comply with the following provisions with respect to insurance coverage: The entire amount of Contractor's liability insurance policy coverage limits, identified in the policy and on the Certificate of Insurance, must, under the policy, be available to pay damages for which the insured Contractor becomes liable, or for which the insured assumes liability under the indemnity agreement herein contained, and such coverage amount shall not be subject to reduction by virtue of investigation or defense costs incurred by Contractor's insurer. 2. The entire amount of the Contractor's liability insurance policy coverage limits shall be payable by the Contractor's insurer, with no deductible to be paid by, or self-insured retention to be attributed to, the Contractor unless this requirement is waived by the City. Contractor's Certificate of Insurance must set forth the nature and amount of any such deductible or self-insured retention. 3. If Contractor's liability insurance coverage is subject to any special exclusions or limitations not common to the type of coverage being provided, such exclusions or limitations shall be noted on the Certificate of Insurance. 4. The City prefers that Contractor provide it with "occurrence form" liability insurance coverage. If Contractor can only provide "claims -made" insurance coverage, then the Contractor must comply with the following requirements: a. If the Contractor changes insurance carriers, or if Contractor's insurance coverage is canceled, during the contract period or within two years after City's acceptance of the work, Contractor agrees to immediately notify the City of such event. b. If Contractor's insurance is canceled or is allowed to lapse during said period, Contractor shall be required to obtain replacement insurance coverage to fulfill its obligation hereunder. C. If, during said period, Contractor voluntarily changes insurance carriers or is required to obtain replacement coverage from another carrier, Contractor shall either (1) purchase "tail" coverage from its first carrier effective for a minimum of two years after City Council acceptance of the work, or (2) purchase "prior acts" insurance coverage from its new carrier, covering prior acts during the period of this Contract from and after its inception. d. "Tail" or "prior acts" coverage so provided shall have the same coverage, with the same limits, as the insurance specified in this Contract, and shall not be subject to any further limitations or exclusions, or have a higher deductible or self-insured retention than the insurance which it replaces. 5. The City reserves the right to waive any of the insurance requirements heretprovided. The City also reserves the right to reject Contractor's insurance if�r Pt in eempliance with the requirements herein provided, and on that basis to either a%WfDheRpntra`cf% the next low bidder, or declare a default and pursue any and all rer�§.fts 0dailat� the City. r� rn M Ca: -4 VE> SC -3 6. In the event that any of the policies of insurance or insurance coverage identified on Contractor's Certificate of Insurance are canceled or modified, or in the event that Contractor incurs liability losses, either due to activities under this Contract, or due to other activities not under this Contract but covered by the same insurance, and such losses reduce the aggregate limits of Contractor's liability insurance below the limits required hereunder, then in that event the City may in its discretion either suspend Contractor's operations or activities under this Contract, or terminate this Contract, and withhold payment for work performed on the Contract. In the event that any of the policies or insurance coverage identified on Contractor's Certificate of Insurance are canceled or modified, the City may in its discretion either suspend Contractor's operations or activities under this Contract, or terminate this Contract, and withhold payment for work performed on the Contract. C. HOLD HARMLESS The Contractor shall indemnify, defend and hold harmless the City of Iowa City and its officers, employees, and agents from any and all liability, loss, cost, damage, and expense (including reasonable attorney's fees and court costs) resulting from, arising out of, or incurred by reason of any claims, actions, or suits based upon or alleging bodily injury, including death, or property damage rising out of or resulting from the Contractor's operations under this Contract, whether such operations be by himself or herself or by any Subcontractor or by anyone directly or indirectly employed by either of them. 2. Contractor is not, and shall not be deemed to be, an agent or employee of the City of Iowa City, Iowa. S-4 SUPERVISION AND SUPERINTENDENCE. Add the following paragraph to 1105.05 of the ]DOT STANDARD SPECIFICATIONS: CONTRACTOR shall maintain a qualified and responsible person available 24 hours per day, seven days per week to respond to emergencies which may occur after hours. CONTRACTOR shall provide to ENGINEER the phone number and/or paging senate of this individual. S-5 CONCERNING SUBCONTRACTORS, SUPPLIERS AND OTHERS. v� c)� a, Add the following paragraph to 1108.01 of the IDOT STANDARD SPECIFICATI(D(g s m Bidders shall list those persons, firms, companies or other pa to whom it proposes/intends to enter into a subcontract regarding this project as required foF-epproval by the City and as noted on the Form of Proposal and the Agreement. If no minority business enterprises (MBE) are utilized, the CONTRACTOR shall furnish documentation of all efforts to recruit MBE's. S-6 COMPLIANCE WITH OSHA REGULATIONS. Add the following paragraphs to 1107.01 of the IDOT STANDARD SPECIFICATIONS: The Contractor and all subcontractors shall comply with the requirements of 29 CFR 1910 SC -4 (General Industry Standard) and 29 CFR 1926 (Construction Industry Standard), The Contractor and all subcontractors are solely responsible for compliance with said regulations. The Contractor will provide Material Safety Data Sheets (MSDS) for all hazardous chemicals or materials that will be at the job site. The Material Safety Data Sheets will be submitted to the Project Engineering prior to the start of construction and supplemented as necessary throughout the project. This data is being provided for informational purposes only and does not relieve the contractor of any obligations for compliance with applicable OSHA and State laws regarding hazardous chemicals and right -to -know. S-7 EMPLOYMENT PRACTICES. Neither the Contractor nor his/her subcontractors, shall employ any person whose physical or mental condition is such that his/her employment will endanger the health and safety of them- selves or others employed on the project. Contractor shall not commit any of the following employment practices and agrees to include the following clauses in any subcontracts: To discriminate against any individual in terms, conditions, or privileges of employment because of sex, race, color, religion, national origin, sexual orientation, gender identity, marital status, age or disability unless such disability is related to job performance of such person or employee. To discharge from employment or refuse to hire any individual because of sex, race, color, religion, national origin, sexual orientation, gender identity, marital status, age, or disability unless such disability is related to job performance of such person or employee. S-8 CONTRACT COMPLIANCE PROGRAM (ANTI -DISCRIMINATION REQUIREMENTS). For all contracts of $25,000 or more, the Contractor shall abide by the requirements of the City's Contract Compliance Program, which is included with these Specifications beginning on page CC -1. S-9 MEASUREMENT AND PAYMENT. Section 01025, Measurement and Payment, contained in Division 1 of these specifications defines all pay items and methods of measurement. The provisions of this section will supersede applicable sections in the IDOT STANDARD SPECIFICATIONS. S-10 TAXES. Contractors and approved subcontractors will be provided a Sales Tax Exemption Certificate to purchase building materials, supplies, or equipment in the performance of the contract. The Contractor shall submit the information necessary for the certificates to be issued. N S-11 CONSTRUCTION STAKES. i Replace the last paragraph of 1105.06 of the IDOT Standard Specifications wif p fcQwin The Contractor shall be responsible for the preservation of stake s -d f�iarks` y necessary re -staking will be at the Contractor's expense and will be charjd*at nate 5 per hour. r.} Y Q SC-5 S-12 BIDDER STATUS DOCUMENTS. The Contractor awarded the project together with all Subcontractors shall be required to complete the form included with these specifications (and entitled the same as this section) and submit it to the Engineer before work can begin on the project. S-13 IRON AND STEEL MANUFACTURING FEDERAL REQUIREMENT. Delete section 1107.06 of the Iowa DOT Standard Specifications SC -6 v o _ n-C-3 � -n =in C" r '<r r- a rn E;= 3 0 w SC -6 Bidder Status Form To be completed by all bidders Part A Please answer "Yes" or "No" for each of the following: ❑ Yes ❑ No My company is authorized to transact business in Iowa. (To help you determine if your company is authorized, please review the worksheet on the next page). ❑ Yes ❑ No My company has an office to transact business in Iowa. ❑ Yes ❑ No My company's office in Iowa is suitable for more than receiving mail, telephone calls, and e-mail. ❑ Yes ❑ No My company has been conducting business in Iowa for at least 3 years prior to the first request for bids on this project. ❑ Yes ❑ No My company is not a subsidiary of another business entity or my company is a subsidiary of another business entity that would qualify as a resident bidder in Iowa. If you answered "Yes" for each question above, your company qualifies as a resident bidder. Please complete Parts B and D of this form. If you answered "No" to one or more questions above, your company is a nonresident bidder. Please complete Parts C and D of this form. To be completed by resident bidders Part B My company has maintained offices in Iowa during the past 3 years at the following addresses: Dates: / / to / / Address: City, State, Zip: Dates: / / to / / Address: City, State, Zip: Dates: / / to / / Address: You may attach additional sheet(s) if needed. City, State, Zip: To be completed by non-resident bidders Part C 1. Name of home state or foreign country reported to the Iowa Secretary of State: 2. Does your company's home state or foreign country offer preferences to bidders who are residents? ❑ Yes ❑ No 3. If you answered "Yes" to question 2, identify each preference offered by your company's home state or foreign country and the appropriate legal citation. You may attach additional sheet(s) if needed. To be completed by all bidders o Part D I certify that the statements made on this document are true and complete to the best of my kno aigi knoWlhat my failure to provide accurate and truthful information may be a reason to reject my bid. —1 ... Firm Name: m You must submit the completed form to the governmental body requescng bid per 875 Iowa Administrative Code Chapter 156. This form has been approved by the Iowa Labor Commissioner. R-1 Worksheet: Authorization to Transact Business This worksheet may be used to help complete Part A of the Resident Bidder Status form. If at least one of the following describes your business, you are authorized to transact business in Iowa. ❑ Yes ❑ No My business is currently registered as a contractor with the Iowa Division of Labor. ❑ Yes ❑ No My business is a sole proprietorship and I am an Iowa resident for Iowa income tax purposes. ❑ Yes ❑ No My business is a general partnership or joint venture. More than 50 percent of the general partners or joint venture parties are residents of Iowa for Iowa income tax purposes. ❑ Yes ❑ No My business is an active corporation with the Iowa Secretary of State and has paid all fees required by the Secretary of State, has filed its most recent biennial report, and has not filed articles of dissolution. ❑ Yes ❑ No My business is a corporation whose articles of incorporation are filed in a state other than Iowa, the corporation has received a certificate of authority from the Iowa secretary of state, has filed its most recent biennial report with the secretary of state, and has neither received a certificate of withdrawal from the secretary of state nor had its authority revoked. ❑ Yes ❑ No My business is a limited liability partnership which has filed a statement of qualification in this state and the statement has not been canceled. ❑ Yes ❑ No My business is a limited liability partnership which has filed a statement of qualification in a state other than Iowa, has filed a statement of foreign qualification in Iowa and a statement of cancellation has not been filed. ❑ Yes ❑ No My business is a limited partnership or limited liability limited partnership which has filed a certificate of limited partnership in this state, and has not filed a statement of termination. ❑ Yes ❑ No My business is a limited partnership or a limited liability limited partnership whose certificate of limited partnership is filed in a state other than Iowa, the limited partnership or limited liability limited partnership has received notification from the Iowa secretary of state that the application for certificate of authority has been approved and no notice of cancellation has been filed by the limited partnership or the limited liability limited partnership. ❑ Yes ❑ No My business is a limited liability company whose certificate of organization is filed in Iowa and has not filed a statement of termination. ❑ Yes ❑ No My business is a limited liability company whose certificate of organization is filed in a state other than Iowa, has received a certificate of authority to transact business in Iowa and the certificate has not been revoked or canceled. ry d T -y ..q r- %3 .Ts R-2 y r ARC 1271C LABOR SERVICES DIVISION[875] Adopted and Filed Pursuant to the authority of Iowa Code section 73A.21, the Labor Commissioner hereby adopts a new Chapter 156, "Bidder Preferences in Government Contracting," Iowa Administrative Code. This amendment adopts new rules concerning preferences for resident bidders on government construction projects. The new chapter sets forth requirements for a public body involved in a public improvement and sets forth enforcement procedures. Notice of Intended Action was published in the October 30, 2013, Iowa Administrative Bulletin as ARC 1160C. Public comments regarding the proposed rules were received. Commenters stated that some of the rules could be misinterpreted and that some of the rules were beyond the statutory authority of Iowa Code section 73A.21. Commenters expressed ideas on how to make the bidding process more efficient. Commenters also questioned the constitutionality of Iowa Code section 73A.21. One commenter suggested adding compliance with Iowa Code chapter 91C as a basis to find that a company is authorized to transact business in Iowa. These rules are not identical to those published under Notice of Intended Action. Some changes are technical; other more substantive changes are described below. References to "domicile" were removed from several rules. Subrule 156.2(l) was changed to clarify that the requirements apply only to a project to be awarded to the lowest responsible bidder; to clarify that only office addresses, not construction worksites, must be reported; to remove a reference to perjury; and to change the deadline for submitting a statement to the public body. Paragraph 156.2(2)"b" was changed by deleting the phrase `under this Act." Subrule 156.2(3) was changed by adding new paragraph "k" concerning construction contractor registration, and by clarifying that compliance with only one of the lettered paragraphs in the subrule is necessary. Paragraph 156.2(4)"b" was changed by adding the phrase "if applicable." In rule 875-156.3(73A), the term "public body" replaced the term "nonresident bidder." A new rule 875-156.9(73A) containing a severability clause was added. The principal reason for adoption of this amendment is to implement legislative intent. No variance procedures are included in these rules because variance provisions are set forth in 875—Chapter 1. After analysis and review of this rule making, no impact on jobs has been found. These rules are intended to implement Iowa Code section 73A.21. These rules shall become effective on February 12, 2014. ro The following amendment is adopted. o en Adopt the following new 875 --Chapter 156: ti CHAPTER 156 BIDDER PREFERENCES IN GOVERNMENT CONTRACTING y��m W -a t 875-156.1(73A) Purpose, scope and definitions. These rules institute administrative'df�ernal procedures for enforcement of the Act. The definitions and interpretations contained,rtn Towa ode section 73A.21 shall be applicable to such terms when used in this chapter. =E'' "Act" means Iowa Code section 73A.21. 3' .J "Affiliate, " when used with respect to any specified person or entity, means another person or entity that, either directly or indirectly through one or more intermediaries, controls, or is controlled by, or is under common control or ownership with, such specified person or entity. "Commissioner" means the labor commissioner appointed pursuant to Iowa Code section 91.2, or the labor commissioner's designee. "Division" means the division of labor of the department of workforce development. R-3 "Nonresident bidder" means a person or entity that does not meet the definition of a resident bidder, including any affiliate of any person or entity that is a nonresident bidder. "Parent, " when used with respect to any specified person or entity, means an affiliate controlling such specified person or entity directly or indirectly through one or more intermediaries. "Public body "means the state and any of its political subdivisions, including a school district, public utility, or the state board of regents. "Public improvement" means a building or other construction work to be paid for in whole or in part by the use of funds of the state, its agencies, and any of its political subdivisions and includes road construction, reconstruction, and maintenance projects. "Public utility" includes municipally owned utilities and municipally owned waterworks. "Resident bidder" means a person or entity authorized to transact business in this state and having a place of business for transacting business within the state at which it is conducting and has conducted business for at least three years prior to the date of the first advertisement for the public improvement. If another state or foreign country has a more stringent definition of a resident bidder, the more stringent definition is applicable as to bidders from that state or foreign country. "Resident labor force preference" means a requirement in which all or a portion of a labor force working on a public improvement is a resident of a particular state or country. "Subsidiary, " when used with respect to any specified person or entity, is an affiliate controlled by such specified person or entity directly or indirectly through one or more intermediaries. 875-156.2(73A) Reporting of resident status of bidders. 156.2(1) Reporting to public body. When a contract for a public improvement is to be awarded to the lowest responsible bidder, the public body shall request a statement from each bidder regarding the bidder's resident status. The statement shall be on the form designated by the commissioner. The statement shall require the bidder to certify whether the bidder is a resident bidder or a nonresident bidder. In the case of a resident bidder, the statement shall require the resident bidder to identify each office at which the resident bidder has conducted business in the state during the previous three years and the dates on which the resident bidder conducted business at each office. In the case of a nonresident bidder, the statement shall require the nonresident bidder to identify the nonresident bidder's home state or foreign country as reported to the Iowa secretary of state, to identify each preference offered by the nonresident bidder's home state or foreign country, and to certify that, except as set forth on the form, there are no other preferences offered by the nonresident bidder's home state or foreign country. The statement shall include such additional information as requested by the commissioner. The statement must be signed by an authorized representative of the bidder. A fully completed statement shall be deemed to be incorporated by reference into all project bid specifications and contract documents with any bidder on a public improvement. Failure to provide the statement with the bid may result in the bid being deemed nonresponsive. This may result in the bid being rejected by the public body. 156.2(2) Determining residency status. a. For purposes of the Act, a person or entity is a resident bidder if the person or entity: (1) Is authorized to transact business in Iowa; and (2) Has had one or more places of business in Iowa at which it is conducting or has conducted business in this state for at least three years immediately prior to the date of the first advertisement for the public improvement. b. If the person or entity is a resident of a state or foreign country that has a more,$ringent definition than is set forth in paragraph 156.2(2) "a" for determining whether a person or entgin that state or country is a resident bidder, then the more stringent definition applies. p O. 156.2(3) Determining authorization to transact business. A person or entity is autWd t�j ansac" business in the state if one or more of the following accurately describes the person o(.entktty: t a. In the case of a sole proprietorship, the sole proprietor is an Iowa resident foi:Z�m imine tO purposes; -G _,. i F' b. In the case of a general partnership or joint venture, more than 50 percent of th ra*tner f" or joint venture parties are residents of Iowa for Iowa income tax purposes;'. !4 =A C. In the case of a limited liability partnership which has filed a statement of qualification in this state, the statement has not been canceled; d In the case of a limited liability partnership whose statement of qualification is filed in a state other than Iowa, the limited liability partnership has filed a statement of foreign qualification in Iowa and a statement of cancellation has not been filed pursuant to Iowa Code section 486A.105(4); e. In the case of a limited partnership or limited liability limited partnership whose certificate of limited partnership is filed in this state, the limited partnership or limited liability limited partnership has not filed a statement of termination; f. In the case of a limited partnership or a limited liability limited partnership whose certificate of limited partnership is filed in a state other than Iowa, the limited partnership or limited liability limited partnership has received notification from the Iowa secretary of state that the application for certificate of authority has been approved and no notice of cancellation has been filed by the limited partnership or the limited liability limited partnership; g. In the case of a limited liability company whose certificate of organization is filed in this state, the limited liability company has not filed a statement of termination; h. In the case of a limited liability company whose certificate of organization is filed in a state other than Iowa, the limited liability company has received a certificate of authority to transact business in this state and the certificate has not been revoked or canceled; I In the case of a corporation whose articles of incorporation are filed in this state, the corporation (1) has paid all fees required by Iowa Code chapter 490, (2) has filed its most recent biennial report, and (3) has not filed articles of dissolution; j. In the case of a corporation whose articles of incorporation are filed in a state other than Iowa, the corporation (1) has received a certificate of authority from the Iowa secretary of state, (2) has filed its most recent biennial report with the secretary of state, and (3) has neither received a certificate of withdrawal from the secretary of state nor had its authority revoked; or k The person or entity is registered with the Iowa division of labor as a construction contractor pursuant to Iowa Code chapter 91C. 156.2(4) Determining if bidder has conducted business in state. In order to determine if a bidder has a place of business for transacting business within Iowa at which it is conducting and has conducted business for at least three years prior to the date of the first advertisement of the public improvement, the bidder shall meet the following criteria for the three-year period prior to the first advertisement for the public improvement: a. Continuously maintained a place of business for transacting business in Iowa that is suitable for more than receiving mail, telephone calls, and e-mails; and b. Conducted business in the state for each of those three years and filed an Iowa income tax return, if applicable, made payments to the Iowa unemployment insurance fund, if applicable, and maintained an Iowa workers' compensation policy, if applicable, in effect for each of those three years. 875-156.3(73A) Application of preference. When awarding a contract for a public improvement to the lowest responsible bidder, the public body shall allow a preference to a resident bidder as ag*st a nonresident bidder that is equal to any preference given or required by the home state or ign cygptry in which the nonresident bidder is a resident without regard to whether such preferenc,i� aIlly enforced by the applicable regulatory body in each state. If the bidder is a subsidiary �relftat would be a nonresident bidder if such parent were to bid on the public improvement in jpec4n n�ie, r then the public body shall allow a preference as against such bidder that is equal to the pr ee given or required by the home state or foreign country of the bidder's parent. In the instance of.'� _ or le preference, a public body shall apply the same resident labor force preference to a public in menu .n this state as would be required in the construction of a public improvement by the home st or for country of the nonresident bidder, or the parent of a resident bidder if the parent woul qualify nonresident bidder if such parent were to bid on the public improvement in its own name. A preference shall not be applied to a subcontractor unless the home state or foreign country of the nonresident bidder to whom the contract was awarded would apply a preference to the subcontractor. R-5 Specific methods of calculating and applying a preference shall mirror those that apply in the home state or foreign country of the nonresident bidder to whom the contract was awarded. In the event that the specific method used by the nonresident bidder's home state or foreign country cannot be determined, the calculation for a labor force preference shall include only the labor force working on the public improvement in Iowa on a regular basis calculated by pay period. 875-156.4(73A) Complaints regarding alleged violations of the Act. 156.4(1) Complaints. Any person with information regarding a violation of the Act may submit a written complaint to the commissioner. Any complaint must provide the information required pursuant to subrule 156.4(2) or as much of such information as is reasonably practicable under the circumstances. The completed written complaint form shall be submitted to the commissioner at Labor Services Division, 1000 East Grand Avenue, Des Moines, Iowa 50319. 156.4(2) Written complaint form. The commissioner shall prepare a written complaint form that a person with information regarding a potential violation of the Act may submit pursuant to subrule 156.4(1). The written complaint form shall request the following information: the name, address, telephone number, and e-mail address of the complainant; the name of the bidder that is believed to have violated the Act; a description of any relationships between the complainant and the bidder; an identification of the public body to which the bidder submitted a bid; the home state or foreign country of the bidder; a description of the goods and services provided under the bid; and such additional information as requested by the commissioner. 156.4(3) Availability ofwritten complaintform. The written complaint form shall be available in all division offices and on the department of workforce development's Internet Web site. 875-156.5(73A) Nonresident bidder record-keeping requirements. While participating in a public improvement, a nonresident bidder from a home state or foreign country with a resident labor force preference shall make and keep, for a period of not less than three years, accurate records of all workers employed by the contractor or subcontractor on the public improvement. The records shall include each worker's name, address, telephone number if available, social security number, trade classification, and starting and ending date of employment. 875-156.6(73A) Investigations; determination of civil penalty. The commissioner or an authorized designee shall cause an investigation to be made into charges of violations of the Act, including allegations set forth in a written complaint. 156.6(1) Investigative powers. The commissioner or the authorized designee shall have the following powers: a. Hearings. The commissioner may hold hearings and investigate charges of violations of the Act. b. Entry into place of employment. The commissioner may, consistent with due process of law, enter any place of employment to inspect records concerning labor force residency, to question an employer or employee, and to investigate those facts, conditions, or matters as are deemed appropriate in determining whether any person has violated the provisions of the Act. The commissioner sly only make an entry into a place of employment in response to a written complaint. r.. c. Residency of workers. The commissioner may investigate and ascertain thgasiderR of aM worker engaged in any public improvement in this state. >::4 —4 ertakd. Oaths; depositions; subpoenas. The commissioner may administer oaths, taeovcaugto her— taken en deposition ofwitnesses, and require by subpoena the attendance and testimony of v & ses and the production of all books, registers, payrolls, and other evidence relevant to a matter unfl , esNation or hearing. e. Employment ofpersonnel. The commissioner may employ qualified personnelo are neibsary for the enforcement of Iowa Code section 73A.21. The personnel shall be employed pursuantAP the merit system provisions of Iowa Code chapter 8A, subchapter IV. f. Request for records. The commissioner shall require a contractor or subcontractor to file, within 10 days of receipt of a request, any records enumerated in rule 875-156.5(73A). If the contractor or subcontractor fails to provide the requested records within 10 days, the commissioner may direct, within 15 days after the end of the 10 -day period, that the fiscal or financial office charged with the custody and disbursement of funds of the public body that contracted for construction of the public improvement or undertook the public improvement, to withhold immediately from payment to the contractor or subcontractor up to 25 percent of the amount to be paid to the contractor or subcontractor under the terms of the contract or written instrument under which the public improvement is being performed. The amount withheld shall be immediately released upon receipt by the public body of a notice from the commissioner indicating that the request for records as required by this paragraph has been satisfied. 156.6(2) Division determination. Upon conclusion of an investigation, the commissioner or an authorized designee shall issue a written determination to the party that was the subject of the investigation. The determination shall indicate whether or not the division finds a violation of the Act by the party. If the determination indicates that the party engaged in a violation of the Act, the determination shall also indicate the remedies the division intends to pursue as a result of the violation. 156.6(3) Informal conference. A party seeking review of the division's determination pursuant to this rule may file a written request for an informal conference. The request must be received by the division within 15 days after the date of issuance of the division's determination. During the conference, the party seeking review may present written or oral information and arguments as to why the division's determination should be amended or vacated. The division shall consider the information and arguments presented and issue a written decision advising all parties of the outcome of the informal conference. 875-156.7(73A) Remedies. Following the conclusion of the informal conference, or following the expiration of the time in which a party may file a written request for an informal conference, the division may pursue the following remedies. 156.7(1) Injunctive relief. If the division determines that a violation of the Act has occurred, the division may sue for injunctive relief against the awarding of a contract, the undertaking of a public improvement, or the continuation of a public improvement. 156.7(2) Civil penalty. Any person or entity that violates the provisions of this chapter is subject to a civil penalty in an amount not to exceed $1,000 for each violation found in a first investigation by the division, not to exceed $5,000 for each violation found in a second investigation by the division, and not to exceed $15,000 for a third or subsequent violation found in any subsequent investigation by the division. Each violation of this chapter for each worker and for each day the violation continues constitutes a separate and distinct violation. In determining the amount of the penalty, the division shall consider the appropriateness of the penalty to the person or entity charged, upon determination of the gravity of the violation(s). The collection of these penalties shall be enforced in a civil action brought by the attorney general on behalf of the division. 875-156.8(73A) Compliance with federal law. If it is determined that application of this chapter and the Act may cause denial of federal funds which would otherwise be available for a public improvement, or would otherwise be inconsistent with requirements of any federal law or regulation, the application of this chapter shall be suspended to the extent necessary to prevent denial of the funds or to eliminate the inconsistency with federal requirements. N 0 875-156.9(73A) Severability. If any rule under this chapter, any portion of a rule r this Gipter, or the applicability of any rule under this chapter to any person or circumstance is h fmvagby A rn a 3 tD R_7 �' r court, the remainder of these rules or the rules' applicability to other persons or circumstances shall not be affected. These rules are intended to implement Iowa Code section 73A.21. [Filed 12/16/13, effective 2/12/141 [Published 1/8/14] EDITOR'S NOTE: For replacement pages for IAC, see IAC Supplement 1/8/14. SECTION 01010 SUMMARY OF THE WORK PART 1- GENERAL General description, not all inclusive. A. Base Bid Work: 1. Supply and install the Playbooster Design 85697-1-3 playground equipment as manufactured by Landscape Structures, Inc. The proposed structure is to be placed at the same location as the existing equipment. 2. Supply and install SMI, Inc. Safety Fiber — Engineered Wood Fiber. 3. Reseed any areas damaged during construction of the project. 4. Other work associated with the playground structure installation. 5/02 shuedkngin eedspecs-fiW 1010 Note: The proposed playground equipment is to be installed at the location of the existing equipment that will be removed prior to the project by the City. Allowable construction access will be from the parking lot to the east of the Mercer Park Aquatic Center. 01010-1 N CA w 4r) 1 a. rn Y t v SECTION 01025 MEASUREMENT AND PAYMENT PART 1- GENERAL 1.01 SUMMARY.• A. Procedures and submittal requirements for schedule of values, applications for payment, and unit prices. 1.02 STANDARD OFMEASUREMENTS. A. Work completed under the contract shall be measured by the Engineer. Payment will be based on the actual quantity of work performed according to the various classes of work specified unless noted in Part 3 of this Section. The Contractor will be given an opportunity to be present during measurement. 1.03 SCOPE OFPAYMENT.- A. The Contractor shall accept the compensation as herein provided as full payment for furnishing materials, labor, tools and equipment and for performing work under the contract; also, for costs arising from the action of the elements, or from any unforeseen difficulties which may be encountered during the execution of the work and up to the time of acceptance. B. Construction items may be bid as a lump sum or as itemized work, which will be paid on a unit cost basis. In either case, some work may be required for which a separate pay item is not provided. Completion of this work is required. If a separate pay item is not provided for this work, it is to be considered incidental to the project and no separate payment will be made. PART2-PRODUCTS N 2.01 NONE o Cr PART 3 - EXECUTION �-� C5 3.01 PROCEDURE. -i r a s A. Payment under this contract shall occur no more than once per month f rk Wmple by the Contractor. Payment is based on an estimate of the total amount d value of work completed minus 5% retainage. It is not the Citys policy to pay for mateFtals and equipment stored or furnishings fabricated off site. The 5% retainage will be released 31 days after the project is accepted by the City Council, provided no claims against the project have been filed within 30 days of project acceptance. Chapter 573 of the Code of Iowa will govern the release of retainage and resolution of claims. 01025-1 3.02 BID ITEMS. A. GENERAL The following subsections describe the measurement of and payment for the work to be done under the items listed in the FORM OF PROPOSAL. Each unit or lump sum price stated shall constitute full payment as herein specified for each item of work completed in accordance with the drawings and specifications, including clean up. It is the Contractor's responsibility to identify the locations of public and private utilities. No additional compensation will be made for any interference or delay caywd by the placement and/or relocation of said utilities. No additional compensatign will `'made for repair costs to fix damage caused by the Contractor or his/her Subcontr o M CF )p associated with existing items on private and/or public propf ty 4hat I e t�'be protected, removed, relocated, replaced, reinstalled or modified is at_1*red incid unless it is listed as an item in the FORM OF PROPOSAL. Existing1t% age unsuitable for relocation or reinstallation will be replaced with like i�nd— me , necessary, at the Contractor's expense. y _ N All trees and shrubs shall remain and be protected from damage unless specifically noted as "REMOVE" or "CLEAR AND GRUB" on the project plans and as otherwise directed by the Engineer. The prices for those items which may have any impact on existing trees and shrubs shall include compensation for special precautionary measures required to prevent injury or damage to said tree, shrub or root system. The prices for those items which involve grading or excavation shall include compensation for top soil removal and replacement (unless it is listed as an item in the FORM OF PROPOSAL), disposal of surplus excavated material, handling water, installation of all necessary sheeting, bracing and temporary fencing around all open excavations and supply, placement and compaction of specified backfill. The prices for those items which involve surface removal adjacent to buildings or vaults shall include compensation to protect exposed surfaces from water which may leak or seep into vaults and/or basements. All labor, materials and equipment required to bring surfaces to the proper elevation and density including loading, hauling, and disposal of unsuitable material, below grade excavation, borrow and hauling, placing, forming, drying, watering and compaction of fill material, and all such work as may be required to make the grading work complete with a uniform surface free of rock, broken concrete, tree roots, limbs and other debris is incidental to this project unless it is listed as an item in the FORM OF PROPOSAL. The Contractor must pay for all parking permit fees, meter hoods, lot and ramp fees, and parking tickets. The Contractor must figure these costs into their bid prices. The City will not waive parking fees or fines. Permits paid for by the Contractor will be issued only for construction vehicles, not personal vehicles. The Contractor shall be responsible for continuous cleaning of mud and debris off adjacent driveways, streets, sidewalks and private property, when mud and debris is deposited there as a result of any construction activity. The cost of clean up shall be incidental. 01025-2 B. BID ITEM DESCRIPTIONS 1. Supply and Install Playground Equipment (LUMP SLIM). 11/00 shmedkngin" tpecs-u\01025.doc The unit price per LUMP SUM shall be considered full compensation for furnishing all materials, labor and equipment necessary to supply and install Playbooster Design 85697-1-3 playground equipment. Equipment must be ordered prior to December 18, 2015. This item also includes the supply and installation of Safety Fiber (Engineered Wood Fiber) ground cover as manufactured by SMI, Inc. Based upon the overall play area dimensions provided, the estimated amount of Safety fiber needed is 500 cubic yards. Any trees, pavement or sidewalks damaged during construction of the play equipment will be replaced at the contractor's expense. Upon completion of the project, the contractor and the City's Representative will review the site to determine if any permanent seeding will need to be performed to repair areas damaged during construction. All areas needing permanent seeding shall be prepared and hydraulically seeded with an Urban mix in accordance with specification section 02900 (Landscaping). Any required permanent seeding will not be paid for separately, but shall be considered incidental to this item. It will be the contractor's responsibility to provide construction fencing as required to secure the site during construction. Construction fencing as required to secure the site will not be paid for separately, but shall be considered incidental to this item. 01025-3 N O J us CD fh 1 i�r� `�r.✓ �_�.'�. to SECTION 01310 PROGRESS AND SCHEDULES PART 1 - GENERAL 1.01 SUMMARY.• A. Prepare, submit and update as necessary a schedule of the work. B. Time is of the essence. Minimizing inconvenience, disruption and duration of disruption to residences and businesses is a high priority. Scheduling of work shall be planned with this in mind. 1.02 SUBMITTALS. A. The Contractor shall submit prior to the Pre -Construction meeting a detailed schedule of the proposed work with the controlling operation identified. The schedule shall include proposed dates and durations of street closings. Work may not begin until the schedule is approved by the Engineer. B. The Contractor shall submit updated construction schedules at two week intervals throughout the project. PART2-PRODUCTS None. PART 3 - EXECUTION a 3.01 MEETINGS PRIOR TO CONSTRUCTION• A. A Pre -Construction meeting will be held prior to beginning work. ter. f ..! D 3.02 PROGRESS OF WORK.- ORK.A. A.Calendar Days for Completion Date and Final Payment Work will be completed and ready for final payment within 173 Calendar Days, in accordance with the General Conditions. 2. Calendar Day count shall start on November 23d, 2015 and continue through the completion of all work. B. Dates for Milestones In addition to the final completion times, there are milestones by which certain work items must be completed: 01310-1 Milestone 1: Ordering of Playground Equipment December 18, 2015 Milestone 1: Any Required Permanent Seeding May 31, 2016 C. Liquidated Damages 1. Contractor and Owner recognize that time is of the essence of this Agreement and that the owner will suffer financial loss if the Work is not completed within the times specified in paragraph 3.02A above, plus any extensions thereof allowed in accordance with the General Conditions. The parties also recognize the delays, expense, and difficulties involved in proving in a legal or arbitration proceeding the actual loss suffered by the Owner if the Work is not completes on time. Accordingly, instead of requiring any such proof, Owner and Contract agree that as liquidated damages for delay (but not as a penalty), ContradfAr hal* OWJq $100 for each day that expires after the time specified in parag_„t3.02a un Work is completed and ready for final payment. n-< I �C m 2. Contractor and Owner recognize that time is of the essence of N-6 ftredlent that the owner will suffer financial loss if the Milestone Work EQ offlete the Milestone dates specified in paragraph 3.02B above, p any , iltensions thereof allowed in accordance with the General Conditions. The pmies also recognize the delays, expense, and difficulties involved in proving in a legal or arbitration proceeding the actual loss suffered by the Owner if the Milestone Work is not completed on time. Accordingly, instead of requiring any such proof, Owner and Contractor agree that as liquidated damages for delay (but not as a penalty), Contractor shall pay Owner $100 for each day that expires after the time specified in paragraph 3.02B until the Milestone Work is complete. 3. Separate sums of liquidated damages which will be assessed for each of the conditions described hereinbefore, and they shall be cumulative if multiple conditions have not been satisfied. D. No work shall be done between the hours of 10:00 p.m. and 7:00 a.m. without the approval of the Engineer, with the exception of saw cutting freshly poured concrete. E. Work will proceed in a well organized and continuous manner to minimize the disruption to the general public (both pedestrian and vehicular) and the local businesses and residents. Access to residences shall be maintained at all times. F. The Contractor will become an active partner with the City in communicating with and providing information to concerned residents. 3.03 COORDINATION WITH UTILITIES AND RAILROADS: A. It is anticipated that many utility conflicts will occur which cannot be taken care of ahead of time. The Contractor shall work closely with the utility companies to aid in these relocations to keep the project on schedule. B. The Railroads will provide all labor, materials and equipment for railroad facility removal, excavation, disposal, sub -drainage, ballast, sub -ballast and trackage renewal. C. The Railroads have certain time limitations on when the above mentioned work must take 01310-2 place. It shall be the Contractor's responsibility to coordinate and be available to meet the Railroads' schedule. Any costs associated with train rerouting due to circumstances caused by the Contractor shall be at the expense of the Contractor. 3.04 STREET CLOSINGS: A. Notify the Engineer four days in advance of street closings so that a press release can be issued. No street may be closed without the Engineers approval and said notification. 11/00 sh..d\e.gine 6p..-a\0131O.dm 01310-3 N C> O Y�l �r m crn SECTION 02900 LANDSCAPING PART 1- GENERAL 1.01 SUMMARY. - A. Plantings (trees, shrubs, seed and sod), including soil preparation, finish grading, landscape accessories and maintenance. L02 QUALITYASSURANCE. A. The fitness of all plantings shall be determined by the Engineer and/or the City Forester with the following requirements: 1. Nomenclature: Scientific and common names shall be in conformity with U.S.D.A. listings and those of established nursery supplies. 2. Standards: All trees must conform to the standards established by the American Association of Nurserymen. B. The Contractor shall repair or replace all plantings which, in the judgment of the Engineer and/or City Forester, have not survived and grown in a satisfactory manner for a period of one year after City Council acceptance of the project. L03 SUBMITTALS: A. Certify that all plantings are free of disease and insect pests. Certificates shall be submitted to the Engineer and/or City Forester. B. Submit certification of seed mixtures, purity, germinating value, and crop year identification to the Engineer. N L04 DELIVERY, STORAGE AND HANDLING: A. Protect all plantings in transit to site to prevent wind burning of foliage.y'o ) M B. Set all balled and burlapped trees and shrubs, which cannot be plantedpCrNately, on ground and protect with soil, wet peat moss or other acceptable ma�taE, aft water Ta required by weather conditions. F C. Keep container grown trees and shrubs, which cannot be planted immediately moist by adequate watering. Water before planting. 02900-1 PART 2 - PRODUCTS 2.01 TREESAIVDSHRUBS: A. Trees and shrubs shall be vigorous, healthy, well -formed, with dense, fibrous and large root systems and free of insect or mechanical damage. B. All trees and shrubs, except those specified as container grown, shall be ballon burlap with root ball formed of firm earth from original and undisturbed soil. A$a mingpm, 89�bf of all plantable containers shall be removed during planting. n C C. All trees shall display the following form and branching habits: �rn z 1. Free of branches to a point at 50% of their height. � 0 0 2. Contain a minimum of six (6) well placed branches, not including type leaden D. Trees shall be measured when branches are in their normal position. Caliper measurement shall be taken at a point on the trunk six inches (6") above ground. E. Trees which have no leader or have a damaged or crooked leader, or multiple leaders, unless specified, will be rejected. Trees shall be freshly dug. 2.02 SEED: 2.03 SOD: A. Grass and sod established, nursery grown Kentucky or Merion Bluegrass sod, vigorous, well rooted, healthy turf, free from disease, insect pests, weeds and other grasses, stones, and any other harmful or deleterious matter. B. Sod harvested by machine at uniform soil thickness of approximately one inch but not less than 3/4 of an inch. Measurement for thickness excludes top growth and thatch. Prevent tearing, breaking, drying or any other damage. 02900-2 Minimum Proportion LbsJ LbsJ Mix by Weight Acre 1,000 sq.ft. URBAN MIX* Kentucky Blue Grass 70% 122.0 2.80 Perennial Rygrass (fine leaf variety) 10% 18.0 0.40 Creeping Red Fescue 20% 35.0 0.80 RURAL MIX* Kentucky 31 Fescue 54% 25 0.57 Switchgrass (Black Well) 17% 8 0.18 Alfalfa (Northern Grown) 11% 5 0.11 Birdsfoot Trefoil (Empire) 9% 4 0.09 Alsike Clover 9% 4 0.09 *A commercial mix may be used upon approval of the Engineer if it contains a high percentage of similar grasses. 2.03 SOD: A. Grass and sod established, nursery grown Kentucky or Merion Bluegrass sod, vigorous, well rooted, healthy turf, free from disease, insect pests, weeds and other grasses, stones, and any other harmful or deleterious matter. B. Sod harvested by machine at uniform soil thickness of approximately one inch but not less than 3/4 of an inch. Measurement for thickness excludes top growth and thatch. Prevent tearing, breaking, drying or any other damage. 02900-2 2.04 LIME AND FERTILIZER: A. Ground agriculture limestone containing not less than 85 percent of total carbonates. B. Fertilizer shall contain the following percentages by weight or as approved by Engineer: Nitrogen* - 15% Phosphorus - 15% Potash -15% *At least 50 percent of nitrogen derived from natural organic sources of ureaform. PART 3 - EXECUTION 3.01 PLANTING TREESAND SHRUBS: A. Planting Season and Completion Date: 1. Trees: Spring- March 30 through May 15 Fall - Sept. 18 through Nov. 18 2. The Contractor may plant outside the limits of such dates with permission of the City Forester. The City Forester may stop or postpone planting during these dates if weather conditions are such that plant materials may be adversely affected. B. The planting shall be performed by personnel familiar with the accepted procedures of planting and under the constant supervision of a qualified planting supervisor. C. Tree and shrub placement shall be as shown on the plans. D. Contractor shall inform the City Forester of the starting date and location. All planting soil must be approved by the City Forester before use. E. Excavate with vertical sides and in accordance with following requirements: 1. Excavate tree pits to a minimum of two feet greater in diameter thangryot ball of tree and sufficiently deep to allow for a minimum of 6 inches of jMnting soil mixture below root ball. -+ 2. Plant shrubs in pits 12 inches greater in width than diamq(gr-Of rdot bay -M container and sufficiently deep to allow for a minimum of 6 inA�pf planting mixture below root ball. rn = �� aG 3. Do not use auger to excavate planting pits. F. Set trees and shrubs in center of pits, align with planting plan, plumb and straight and at elevation where top of root ball is one inch lower than surrounding finished grade after settlement. G. Compact topsoil mixture thoroughly around base of root ball to fill all voids. Cut all burlap and lacing and remove from top one-third of root ball. Do not pull burlap from under any root ball. Backfill tree and shrub pits halfway with planting soil mixture and thoroughly puddle before further backfilling tree or shrub pit. Water tree or shrub again when backfill operation is complete. 02900-3 H. Rake bed area smooth and neat. Mulch all tree pits and shrub beds with a minimum of three inches of hardwood mulch which has been approved by the City Forester. 3.02 PLANTING SOIL MIXTURE: A. Backfill material for plantings shall be a mixture of 2/3 loose friable topsoil and 1/3 clean sand. All backfill shall have a uniform appearance and shall be loose, friable, and free of hard clods and rock over two inches in diameter. N 0 3.03 SEED, FERTILIZE, LIMEAND MULCH C "n -4 .�.� A. Apply lime by mechanical means at rate of 3,000 pounds per acre. C + (� B. Apply fertilizer at rate of 450 pounds per acre. G rn Nrm C. Seed Areas: o x o 1. Remove weeds or replace loam and reestablish finish graderif an3pelays in seeding lawn areas allow weeds to grow on surface or loam is washed out prior to sowing seed. This work will be at the Contractor's expense. 2. Sow seed at rate of 175 pounds per acre on calm day, by mechanical means. Sow one-half of seed in one direction, and other one-half at right angles to original direction. 3. Rake seed lightly into loam to depth of not more than %<-inch and compact by means of an acceptable lawn roller weighing 100 to 150 pounds per linear foot of width. 4. Hydro -seeding may be used upon approval of the Engineer. D. Water lawn area adequately at time of sowing and daily thereafter with fine spray until germination, and continue as necessary throughout maintenance and protection period. E. Seed during approximate time periods of April I to May 15 and August 15 to September 15, and only when weather and soil conditions are suitable for such work, unless otherwise directed by the Engineer. F. All areas requiring mulch shall be mulched as soon as seed is sown and final rolling is completed. Mulch shall be evenly and uniformly distributed and anchored into the soil. The application rate for reasonably dry material shall be approximately I %: tons of dry cereal straw, two tons of wood excelsior, or two tons of prairie hay per acre, or other approved material, depending on the type of material furnished. All accessible mulched areas shall be consolidated by tilling with a mulch stabilizer, and slope areas shall be tilled on the contour. Crawler -type or dual -wheel tractors shall be used for the mulching operation. Equipment shall be operated in a manner to minimize displacement of the soil and disturbance of the design cross section. G. Apply additional care as necessary to ensure a hearty stand of grass at the end of the one- year maintenance period. 3.04 SOD: A. Install sod not more than 48 hours after cutting. Stake all sod as necessary to prevent erosion before establishment. B. Apply lime by mechanical means at a rate of 3,000 pounds per acre. C. Apply fertilizer at a rate of 450 pound per acre. D. Remove weeds or replace loam and reestablish finish grades if there are any delays in sodding. E. Rake area to be sodded. F. Roll sod to establish smooth, uniform surface. G. Water area adequately at time of sodding and continue as necessary throughout maintenance period. H. Sod during approximate time periods of April 1 to May 15 and August 15 to October 15, and only when weather and soil conditions are suitable for such work, unless otherwise directed by the Engineer. I. Apply additional care as necessary to ensure a hearty stand of grass at the end of the one- year maintenance period. 3.05 MAINTENANCE -ALL PLANTINGS: A. Begin maintenance immediately and continue maintenance until final acceptance of work. Water, mulch, weed, prune, spray, fertilize, cultivate and otherwise maintain and protect all plantings. B. Maintain sod and seed areas at maximum height of 2%, inches by mowing at least three times. Weed thoroughly once and maintain until time of final acceptance. Reseed and refertilize with original mixtures, watering, or whatever is necessary to establish, over entire area, a close stand of grasses specified, and reasonably free of weeds and undesirable grasses. C. Reset settled trees and shrubs to proper grade and position, and remove dead material. D. All plantings shall be guaranteed for a period of one year after by City Council acceptance of the project. E. The Contractor shall supply all water for planting and maintenance. Water may be obtained at the Contractor's expense at the bulk water fill station located at 1200 S. Riverside Drive. All water must be paid for in advance at the Civic Center, 410 E. Washington Street. 11/00 sh=d�.g.eeAspm-II\02900.dm 02900-5 N '�J O f C7 fie rri " a m _a _ ko SECTION 03500 MATERIALS Material Specifications Quote: 85697-1-3 playbooster (2-5 years) 9/24/2015 Material Specifications: 114373A Belt Bridge (42") Belt: Made from .315" (8,00 mm) thick mini rough top 3 -ply rubber belting with polyester fabric plys, black in color. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Permalene Panel: One -color panel measures 35 5/8" (904,88 mm) wide x 40 1/2" (1028,7 mm) high, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Mounting Angle: Weldment comprised of 2 1/2" (63,5 mm) wide x 2 1/2" (63,5 mm) high x 36 1/2" (927,1 mm) long formed 10 GA (.135') (3,43 mm) carbon steel with 3/8" x 1 1/8" (9,53 mm x 28,58 mm) stainless steel studs. Finish: TenderTuff, color specified. Mounting Plate: Fabricated from 2" (51 mm) wide x 36 1/2" (927,1 mm) long 3/16" (4,75 mm) HR flat steel. Finish: ProShield, color specified. 123284C N Wiggle Ladder 48"Dk DB fJ "� Rail: Fabricated from 13/16" (20,64 mm) diameter x 27 15/16" (709,60 mm) long CRS so*sat StA with both ends tapped 3/8" (9,53 mm). Finish: TenderTuff, color specified. r J -4 cn r Support: Fabricated from 1.315' (33,40 mm) O.D. RS -20 (.080" -.090") (2,03 mm -2,28 ma Iva ed rn steel tubing. ;sa Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. r Handhold Panel: Permalene, color specified. 03500-1 Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Chain: 4/0 Chain zinc plated. Finish: TenderTuff, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. 128252A Loop Ladder 48"Dk DB Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Handhold Panel: Permalene, color specified. Loop Ladder: Weldment comprised of 1.125' (28,58 mm) O.D. x 11 GA (.120") (3,04 mm) black steel tubing. Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (So) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Zn = Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 ProShield, color specified. 143199B Conical Climber 40"Dk DB Handhold Panel: Recycled Permalene, color specified. 0 0 11/16" (42,85 mma�'sh� ' n n-< m r rn �m a S Y ro Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Belt: PVC belting, 5/16" (7,92 mm) thick, 300 PIW tension rating. Center Loop: Weldment comprised of 1.315' (33,40 mm) O.D. RS -20 (.080" -.090") (2,03 mm -2,28 mm) galvanized steel tubing, 1/4" x 1 1/4" (6,35 mm x 31,75 mm) HR flat steel and 1/4" x 2 3/4"(6,35 mm x 69,85 mm) HR flat steel. Finish: ProShield, color specified. Footer: Fabricated from 1.125' (28,58 mm) O.D. x 11 GA (.120") (3,04 mm) galvanized steel tubing. Finish: ProShield, color specified. Hand Grip: Made from Polyester Resin. Hand Grips measure 5 3/4" (146,05 mm) long x 2 1/2" (63,5 mm) wide x 13/4" (44,45 mm) high. 03500-2 Mounting Plate: Fabricated from 1/8" (3,17 mm) HR flat steel. Finish: ProShield, green in color. Rails: Weldment comprised of 1.315" (33,40 mm) O.D. RS -20 (.080" -.090") (2,03 mm -2,28 mm) galvanized steel tubing, and 1/4" x 1 1/4" (6,35 mm x 31,75 mm) HR flat steel. Finish: ProShield, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16"(42,85 mm). Finish: ProShield, color specified. 153076A Mini Summit Climber 48"Dk DB Handhold Panel: Permalene, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Summit Climber: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Support: Weldment comprised of 2.375' (60,33 mm) O.D. RS -20 (.095' -.105") (2,41 mm -2,66 mm) galvanized steel tubing and 1/4" x 3" (6,35 mm x 76 mm) mounting plate. Finish: ProShield, color specified. 111228A Square Tenderdeck Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Square Deck: Flange formed from 12 GA (.105') (2,66 mm) sheet steel conforming to ASTM A 1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face mounting components. The finished size measures 2 5/8" x 47" x 47"(66,68 mm x 1194 mm x 1194 mm). Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications)., ; �+ �, o �TJ -------------------- C7� t Q1 111231A b. M s TriangularTenderdeck '-0 D .c— Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Triangular Deck: Flange formed from 12 GA (.105') (2,66 mm) sheet steel conforming to ASTM Al 011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face 03500-3 mounting components. The finished size measures 2 5/8" x 37 3/4" (66,68 mm x 958,85 mm). Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 121948A Kick Plate 8"Rise Kick Plate: Fabricated from 11 GA (.120") (3,04 mm) HR flat steel. Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). -------------------- 178710A _ o Hexagon Tenderdeckn _ v� Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. o, rn frt a Deck Brace: Fabricated from 3/8" x 13/4" x 28 1/2" long zinc plated steel strap. Finish: POE§Iver 10 color. ix o v Hex Deck: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A 1011. 9Uding surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face mounting components. The finished size measures 2 5/8" x 36 3/4" (66,68 mm x 933,45 mm) per each of the six sides for an overall dimension of 77 5/8" (1971,68 mm) face to face. Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 184354A Curved Transfer Module Left 2-5yrs 32"Dk DB Deck Support: Weldment comprised of 3 1/2" (88,9 mm) O.D. RS -20 (.125') (3,17 mm) galvanized steel tubing and 3/8" (9,53 mm) O.D. x 5" (127 mm) long CRS rod. Finish: ProShield, color specified. Deck: Flange formed from 12 GA (.105') (2,66 mm) HRPO sheet steel conforming to ASTM A1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes and measures 29" (737 mm) per (2) sides. Finish: TenderTuff, color specified. Panels: Permalene, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. 03500-4 Railings: Weldment comprised of formed 11/8" O.D. x i l GA (.120") steel tubing, 3/16" thick HR flat steel, 3/16" thick HRPO steel plate and 3/4" O.D. x 11 GA. (.120") stainless steel tubing. Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Fabricated from 6061-T6 aluminum 1 1/8" (28,58 mm) O.D. x 1 1/4" (31,75 mm). Finish: ProShield, color specified. Spacer Tube: Made from 1 1/8" O.D. 6061-T6 aluminum tubing. Finish: ProShield®, color specified. Stl. Hanger Clamp: Weldment comprised of 1/4" HRPO flat steel. Finish: ProShield®, color specified. Step Support: Weldment comprised of 1.660" (42,16 mm) O.D. RS -20 (.080" -.095") (2,03 mm -2,41 mm) galvanized steel tubing and 1 3/4" x 13/4" x 1/8" (44,45 mm x 44,45 mm x 3,17 mm) HR angle. Finish: ProShield, color specified. Step Sections/Top Step Section: Formed from 12 GA (.105') (2,66 mm) HRPO sheet steel conforming to ASTM A1011. Standing surface is 24 3/8" (619,13 mm) wide x 14" (355,6 mm) deep and is perforated with 5/16" (7,92 mm) diameter holes. Finish: TenderTuff, color specified. 1112408 Balcony Deck w/Wheel Wheel: 12" (305 mm) diameter cast A319.1 aluminum alloy. Shaft -303 stainless steel. Finish: TenderTuff, color specified. Wheel Bracket: Weldment comprised of formed 3/16" (4,75 mm) plate and 5/8" (15,88 mm) O.D. stainelss steel shaft. Finish: ProShield, color specified. Wheel Clamp: Formed from 3/16" x 2" (4,75 mm x 52 mm) HRPO zinc -plated. Finish: ProShield, color specified. Barrier: Weldment comprised of 5/8" (15,87 mm) solid steel vertical rails, 1 1/8" (28,57 tum) O.D. steel horizontal rails with 203 or 303 stainless steel welded inserts with 5/8" (15,87 mm) internal threads. Finish: TenderTuff, color specified. Deck: Fabricated from 12 GA (.105') (2,66 mm) sheet steel conforming to ASTM A1011. Standing surface is perforated with 5/16" (7,93 mm) diameter holes perforated. The finished size measures 2 5/8" x 34" (66,67 mm x 863 mm) (straight edge) x 17" (431 mm) radius (curved edge). Finish: TenderTuff, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. N O Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless st (SST ger ASTM F 879 unless otherwise indicated (see specific product installation/specifications). c -------------------- ..i fn C -n rn a. M ME 03500-5 v 115222A Slant Window Panel Above Deck Window: .177" (4,50 mm) thick clear polycarbonate. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Angled Panel Bracket: Weldment comprised of .190" (4,83 mm) thick 5052 aluminum formed angle with (2) 6005-T5 aluminum threaded tubes 1 1/8" (28,58 mm) O.D. x 1 1/2" (38,1 mm) long. Finish: ProShield, color specified. Permalene Panel: One -color panel measures 35 5/8" (904,88 mm) wide x 41" (1041 mm) high, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). N O Braces: One -color Permalene, yellow, tan or red in color. o 0 C -) Window Section: Rotationally molded from U.V. stabilized linear low density polye�i e, ccplor specified. m Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm a sh:= G7 ProShield, color specified. o r o 115227A Zoo Panel Above Deck Panels: Permalene, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Angled Panel Bracket: Weldment comprised of. 190" (4,83 mm) thick 5052 aluminum formed angle with (2) 6005-T5 aluminum threaded tubes 1 1/8" (28,58 mm) O.D. x 1 1/2" (38,1 mm) long. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 nun). Finish: ProShield, color specified. 159459A Ring -A -Bell Panel Above Deck Bell: Fabricated from 10 GA. (.135") (3,42 mm) HRPO low carbon steel. Finish: ProShield, color specified. 03500-6 Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified Angled Panel Bracket: Weldment comprised of .190" (4,83 mm) thick 5052 aluminum formed angle with (2) 6005 -TS aluminum threaded tubes 1 1/8" (28,58 mm) O.D. x 1 1/2" (38,1 mm) long. Finish: ProShield, color specified. Permalene Panel: Two color panel measures 35 5/8" (904,88 mm) wide x 41" (1041 mm) high, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16"(42,85 mm). Finish: ProShield, color specified. Bell Striker: Recycled Permalene, color specified 164092A Bongo Panel Above Deck Bongo: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Angled Panel Bracket: Weldment comprised of .190" (4,83 mm) thick 5052 aluminum formed angle with (2) 6005-T5 aluminum threaded tubes 1 1/8" (28,58 mm) O.D. x 1 1/2" (38,1 mm) long. Finish: ProShield, color specified. Permalene Panel: Two color panel measures 35 5/8" (904,88 mm) wide x 41" (1041 mm) high, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Screen Plate: Fabricated from 12 GA. (.105") (2,66 mm) HRPO flat steel. Finish: Black in color. Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. R� -------------------- Ui 152179A c < Saddle Spinner DB 12"Height ,, a-� M I v M Spinner Seat: Rotationally molded from U.V. stabilized linear low density polyethylene ni gig =I/4" (463,55 mm) wide x 7" (178 mm) high, color specified. W 03500-7 Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Rubber Gasket: Made from 50 durometer neoprene. Shaft Assembly: (Spinner Seat Post) Weldment comprised of 2.875' (73,03 mm) O.D. RS40 (.160"-.170") (4,06 mm -4,32 mm) Wall galvanized steel tubing, 1.250" (31,75 mm) O.D. steel shaft, 12 Ga. (.105') (2,66 mm) HR flat steel and 1144 steel collar. Finish: ProShield, color specified. (Sleeve/Plate) Weldment comprised of 1/4" (6,35 mm) sheet HRPO steel and 2.875' (73,03 mm) O.D. schedule 80 steel tubing. Finish: ProShield, color specified. 164074B Single Bobble Rider DB na Ca_ Leg: Weldment comprised of 3.500" (88,9 mm) O.D. RS20 (.120"-.130") (3,04 mm -3,30 qga) waIg --� galvanized steel tubing and 1/4" x 10" (6,35 mm x 254 mm) diameter HRPO zinc plated sto2inig ProShield, black in color. —� CC') Spring: Weldment comprised of 5 5/8" (142,87 mm) diameter 13/16" (20,63 mm) tempered�steyl.coil.M Finish: ProShield, black in color. S Bobble Rider: Weldment comprised of 1.315' (33,40 mm) O.D. RS20 (.080"-.090") (2,03 Alia -2,28 ttrm) wall galvanized steel tubing, 2.375' (60,32 mm) O.D. RS20 (.095'-.105') (2,41 mm -2,66 mm) wall galvanized steel tubing, 3/8" (9,52 mm) HRPO steel plate, 1/4" (6,35 mm) HRPO steel plate, and 4" (101 mm) diameter 10 GA. (.135') (3,42 mm) low carbon steel ball. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Seat: Rotationally molded from U.V. stabilized linear low density polyethylene, black in color. 164075B Double Bobble Rider DB Footer: Weldment comprised of 3.500" (88,9 mm) O.D. RS20 (.120"-.130") (3,04 mm -3,30 mm) wall galvanized steel tubing and 1/4" x 10" x 17" (6,35 mm x 254 mm x 431 mm) sheet HRPO steel. Finish: ProShield, black in color. Spring: Weldment comprised of 5 5/8" (142,87 mm) diameter 13/16" (20,63 mm) tempered alloy steel coil. Finish: ProShield, black in color. Bobble Rider: Weldment comprised of 1.315' (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,28 mm) wall galvanized steel tubing, 2.375' (60,32 mm) O.D. RS20 (.095'-.105') (2,41 mm -2,66 mm) wall galvanized steel tubing, 3/8" (9,52 mm) HRPO steel plate, 1/4" (6,35 mm) HRPO steel plate, and 4" (101 mm) diameter 10 GA. (.135') (3,42 mm) low carbon steel ball. Finish: ProShield, color specified. 03500-8 Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Seat: Rotationally molded from U.V. stabilized linear low density polyethylene, black in color. 111403E 150"Alum Post For Roof DB Post: See PlayBooster (PB) General Specifications. 111403C 166"Alum Post For, Roof DB Post: See PlayBooster (PB) General Specifications. 111404E 116"Alum Post DB Post: See PlayBooster (PB) General Specifications. 130567A Hex Shingle Roof Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Roof Sleeve: Cast from A356 aluminum alloy. Hex Shingle Roof Section: Rotationally molded from UN specified. 168100A Sensory Play Center Wall DB Wall Mount Plate: Weldment comprised of 2.375' (60,33 mm) O.D. RS20 (.095'-.105") (2,41 mm -2,66 mm) wall galvanized steel tubing and 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield, color specified. Wall Plate: Fabricated from 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield, color specified. 03500-9 N O stabilized linear low density pot5thylergcolor� *465C --j C-)rrn A 1��+'��' Wall Mount Plate: Weldment comprised of 2.375' (60,33 mm) O.D. RS20 (.095'-.105") (2,41 mm -2,66 mm) wall galvanized steel tubing and 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield, color specified. Wall Plate: Fabricated from 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield, color specified. 03500-9 Wall: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 168101A Sensory Play Center Wall End DB Wall Mount Plate: Weldment comprised of 2.375' (60,33 mm) O.D. RS20 (.095'-.105") (2,41 mm -2,66 mm) wall galvanized steel tubing and 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield, color specified. Wall: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). N 0 -------------------- o 168105A --4 C-) r Imagination Table fir— a m m s Q Z3= Permalene Panel: Two color, color specified. :EX O Y Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). M-13DI:V Kaleidospin Panel Kaleidoscope Panel Assembly: (Panels) Two color Permalene, color specified. (Tubes) Weldment comprised of 2.375' (60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm -3,56 mm) galvanized tubing and 7 GA. (.179") (4,55 mm) sheet HRPO steel. Finish: ProShield, color specified. (Mirror) Fabricated from 22 GA. (.030") (0,76 mm) stainless steel sheet. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 168661A Sensory Play Station Plate Wall Plate: Fabricated from 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield, color specified. 03500-10 Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 177715A Color Splash Panel Color Splash Panel Assy.: Assembly comprised of (Permalene Panels), color specified. (Lexan Panel) 1/4" (6,35 mm) thick x 26 3/4" (679,45 mm) diameter. (Acrylic Panel) 1/8" (3,18 mm) thick x 26 3/4" (679,45 mm) diameter clear. (Color Wheel) .1875" (4,76 mm) thick x 23 7/16" (595,30 mm) diameter aluminum sheet. Finish: ProShield, image is transferred into paint by the process of infusion. (Shaft) 300 Series stainless steel. (Thrust Oilite Bearing) .125' (3,18 mm) thick x 2.875' (73,03 mm) diameter. (Sleeve Oilite Bearing) 1.25' (31,75 mm) diameter x.750" (19,05 mm) long. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 182503A Welcome Sign (LSI Provided) Ages 2-5 years Direct Bury Border: Permalene, black in color. Sign Panel: Panel is fabricated from 1/8" (.125')(3,17 mm) aluminum plate. Finish: ProShield®, gray in color. (Sign) Digital image is transfered to a 1/8" (.125')(3,17 mm) ProShield coated aluminum plate, then infused into the ProShield. Post: Weldment comprised 2.375' (60,33 mm) O.D. RS20 (.095-.105) (2,41 mm -2,67 mm) wall galvanized tube, 1/4" (6,35 mm) HRPO steel sheet and aluminum post cap. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). o ---- --------------- n C-) t t 122033D� rn �r m SpyroSlide 56"w/Hanger Bracket DB M Z TJ� ti l7 Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. T> F cca Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Rail: 1 1/8" (28,58 mm) O.D. 6061-T6 aluminum extrusion with 5/16" (7,92 mm) walls. Finish: ProShield, color specified. 03500-11 Barrier Plates: Fabricated from 1/4" x 1 1/2" (6,35 mm x 38,1 mm) zinc plated HRPO flat steel. Finish: ProShield, color specified. Center Column: Fabricated from 3.500" (88,9 mm) O.D. RS-20 (.120" -.130") (3,04 mm-3,30 mm) galvanized steel tubing. Finish: ProShield, color specified. Entrance Deck: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes and measures 313/4" (806,45 mm) wide x 36 27/32" (935,81 mm) long. Finish: TenderTuff, color specified. Exit Support: Weldment comprised of 2.375' (60,33 mm) O.D. RS-20 (.095' -.105") (2,41 mm-2,66 mm) galvanized steel tubing and 1/4" (6,35 mm) thick zinc plated HRPO flat steel. Finish: ProShield, color specified. Slide, Hood & Barriers: Rotationally molded from U.V. stabilized linear low-density polyethylene, color specified. Handbar: Formed from 7/8" (22,23 mm) O.D. x 11 GA (.120") (3,04 mm) black steel tubing. Finish" TenderTuff, brown in color. gc� o Hanger Bracket: Formed from 11 GA (.120") (3,04 mm) HRPO low carbon sheet steel. Fin9RcnPwTuff color specified. -------------------- m a m � a 123331A D a 0 Double Poly Slide 32"Dk DB Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Rail: Extruded from 1.125' ((28,58 mm) O.D. x.312" (7,92 mm) wall. 6005-T5 aluminum. Finish: ProShield, color specified. Hood: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Exit Support: Weldment comprised of 2.375' (60,33 mm) O.D. RS-20 (.095' -.105") (2,41 mm x 2,66 mm) galvanized steel tubing and 1/4" x 3" (6,35 mm x 76 mm) mounting plate. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Rail Spacer: Fabricated from 1.312" (33,32 mm) O.D. x 16 GA (.065') (1,65 mm) steel tubing. Finish: ProShield, color specified. Slide: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11 /16" (42,85 mm). Finish: ProShield, color specified. 03500-12 123336A Double Wave Poly Slide 48"Dk DB Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Rail: Extruded from 1.125" ((28,58 mm) O.D. x.312" (7,92 mm) wall. 6005-T5 aluminum. Finish: ProShield, color specified. Hood: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Exit Support: Weldment comprised of 2.375' (60,33 mm) O.D. RS -20 (.095' - .105") (2,41 mm x 2,66 mm) galvanized steel tubing and 1/4" x 3" (6,35 mm x 76 mm) mounting plate. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Rail Spacer: Fabricated from 1.312" (33,32 mm) O.D. x 16 GA (.065') (1,65 mm) steel tubing. Finish: ProShield, color specified. Mid -Support: Weldment comprised of 1.660" (42,16 mm) O.D. RS -20 (.085' -.095") (2,16 mm -2,41 mm) galvanized steel tubing and 1/4" x 3" (6,35 mm x 76 mm) zinc plated flat steel. Finish: ProShield, color specified. Slide: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Spacer: One -color Permalene, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. 119641A Wire Crawl Tunnel Above Deck N O_ Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. _ C s Angled Panel Bracket: Weldment comprised of. 190" (4,83 mm) thick 5052 aluminum fonr�e�cf8ligle with (� 6005-T5 aluminum threaded tubes 1 1/8" (28,58 mm) O.D. x 1 1/2" (38,1 mm) long. Finish5 hi , coldr specified. a rn TL7 _ Permalene Panel: One -color panel measures 35 5/8" (904,88 mm) wide x 41"(1041 mm) hi 10 MR specified. r CA Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. Rings: One -color Permalene, color specified. 03500-13 Wire Tunnel: Formed from 1/4" (6,35 mm) diameter wire with 2" x 3" (51 minx 76 mm) openings. Wire tunnel measures 28" (711 mm) in diameter and 35 3/8" (898,53 mm) long. Finish: TenderTuff, color specified. Warranty: You have our word. More than just a contract, our warranty is our personal commitment that you'll be satisfied with your purchase now and well into the future. As an employee -owned company we take great pride in the quality of everything we make. And we're so confident that you'll be delighted with your purchase that we back our products with the most comprehensive long-term warranties in the industry. It's just one more way that we show how much we care about our customers and communities. N O 100 -YEAR LIMITED WARRANTY On all P1ayBooster®, PlayShaper® and PlaySense® aluminum posts, stainless steel faster clips, be" and caps, against structural failure due to corrosion/natural deterioration or manufacturiri;Ziectr and oa.— PlayBooster, EvosTM and WeevosTM steel posts and arches against structural failure due 1"eriI2�or manufacturing defects.m �m p 15 -YEAR LIMITED WARRANTY o:X o Q On all plastic components (including TuffrimbersTM edging), all steel components (exceo00-y(a steel posts), Mobius® climbers, decks and TenderTuffrM coatings (except Wiggle Ladders, Chain Ladders and Swing Chain) against structural failure due to material or manufacturing defects. Tuffrurtg tiles against material or manufacturing defects. 10 -YEAR LIMITED WARRANTY On concrete products against structural failure due to natural deterioration or manufacturing defects. Does not cover minor chips, hairline cracks or efflorescence. 8 -YEAR LIMITED WARRANTY On AeronetTM climbers and climbing cables against defects in materials or manufacturing defects. On CoolToppers® fabric against failure from significant fading, deterioration, breakdown, mildew, outdoor heat, cold or discoloration. This warranty is limited to the design loads as stated in the specifications found in the technical information. 3 -YEAR LIMITED WARRANTY On all other parts, i.e.: CableCore® products, swing seats and hangers, grills, Mobius climber handholds, Wiggle Ladders, Chain Ladders and Swing Chain, Track Ride trolleys and bumpers, all rocking equipment including Sway Fun® gliders, PVC belting material, HealthBeatTM hydraulic cylinders, Seesaws, Wiggle Ring Bridge, etc., against failure due to corrosion/natural deterioration or manufacturing defects. This warranty does not include any cosmetic issues or wear and tear from normal use. It is valid only if the playstructures and/or equipment are erected to conform with Landscape Structures' installation instructions and maintained according to the maintenance procedures famished by Landscape Structures Inc. For a full text of the warranty, contact your playground consultant. 03500-14 Material Specifications Quote: 85697-1-3 playbooster(5-12 years) 9/24/2015 Material Specifications: 114665A Arch Bridge (42") Offset Hanger Clamp Assembly: Cast aluminon. Finish: ProShield, color specified. Arch Bridge: Fabricated from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A 1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Panel: One -color panel measures 35 5/8" (904 mm) wide x 41" (1040 mm) high, color specified. No Material Spec for 193171C 158997A Pod Climber 10" DB Disc: Rotationally molded from U.V. stabilized linear low density polyethylene, disc measures 14" (356 mm) in diameter x 7" (178 mm) high, color specified. Support: Weldment comprised of 1.900" (48,26 mm) O.D. RS -20 (.090" -.100") (2,28 mm -2,54 mm) 1.315" (33,40 mm) O.D. RS -20 (.080" - 090") (2,03 mm -2,28 mm) and 3/16" x 5" (4,75 mm x 127 mm) diameter plate. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 03500-15 ry 0 158998A A o C Pod Climber 20" DB -< IM Cn r Disc: Rotationally molded from U.V. stabilized linear low density polyethylene, disc mel%q— s 14; (356V") in diameter x 7" (178 mm) high, color specified. _ km r co 03500-15 Support: Weldment comprised of 1.900" (48,26 mm) O.D. RS -20(.090" -.100")(2,28 mm -2,54 mm) 1.315" (33,40 mm) O.D. RS -20 (.080" - 090") (2,03 mm -2,28 mm) and 3/16" x 5" (4,75 mm x 127 mm) diameter plate. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). -------------------- No Material Spec for 111812A c u+ -------------------- D 207582A e�t-E Ct p 1 , , The Bend Rock 3 o�r o Handhold Frame: Weldment comprised of 1.125' (28,58 mm)O.D. 11 GA. (.12011) (3,04 in steel tubing with 203 or 303 stainless steel inserts, with 5/8" (15,88 mm) internal threads and 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield, tan in color. Rock Panel: Weldment comprised of 5/8" (15,87 mm) & 3/4" (19,06 mm) rebar, 1/4" (6,35 mm) HRPO steel sheet and 7 GA. (.179") (4,55 mm) thick HRPO steel plate. Finish: ProShield®. (Rock -fully assembled) Wet cast solid pour concrete product. Finish: Latex paint made for concrete, natural colors. Wall Mount Brkt.: Fabricated from 7 GA. (.179") (4,55 mm) thick HRPO steel plate. Finish: ProShield®, color specified. Poly Board: Recycled high-density polyethylene, cedar and mink in color. Wall Mount Clamp: Weldment comprised of 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield®, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Spacer Tube: Made from 1 1/8" (28,58 mm) O.D. 6061-T6 aluminum tube. Finish: ProShield, tan in color. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). -------------------- 116249D Vertical Ladder 72"Dk DB Footer: Fabricated from 1.315' (33,40 mm) O.D. RS -20 (.080" -.090") (2,03 mm -2,28 mm) galvanized steel tubing. Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Handhold Panel: Permalene, color specified. 03500-16 Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. Vertical Ladder: Weldment comprised of 1.125" ((28,58 mm) O.D. x 11 GA (.120") (3,04 mm) steel tubing, 1.029" (26,14 mm) O.D. RS -20 (.070" -.080") (1,78 mm -2,03 mm) and 3/16" x 2" (4,75 mm x 51 mm) wide steel flat plates. Finish: TenderTuff, color specified. 122913B Snake Climber 72"Dk DB Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Climber: Weldment comprised of 1.660" (42,16 mm) O.D. RS -40 (.111" - .121 ") (2,82 mm -3,07 mm) galvanized steel tubing, and 1.315" (33,40 mm) O.D. RS -20 (.080" -.090") (2,03 mm -2,28 mm) galvanized steel tubing. Finish: ProShield, color specified. Handhold Panel: Permalene, color specified. Support: Formed from 1.660" (42,16 mm) O.D. RS -40 (.111" - .121 ") (2,82 mm -3,07 mm) galvanized steel tubing. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. 145624D Vertical Ascent 72"Dk Panels: Permalene, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). N O Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. Finish: ProShield, coi' specA-ed. Clamps: Cast aluminum. Finish: ProShield, color specified. '{ Made from Polyester Resin. Handholds measure approx. 5 3/4" (146,05 mm) long x 2 1/ 1115 mm) x 13/4" (44,45 mm) high. -------------------- F 03500-17 148039A Star Seeker DB Only Attached to Square Deck Anchor Bar: Weldment comprised of 1/2" x 3" (12,7 mm x 76 mm) flat steel and 1/4" x 8" (6,35 mm x 203 mm) square plate. Finish: Galvanized. N Infill Panel: Recycled Permalene, color specified. _o ,oro Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainlestQ (SET) per. ASTM F 879 unless otherwise indicated (see specific product installation/specifications). n _< I r m Net: Made of tightly woven polyester -wrapped, six -stranded galvanized -steel cable with a;14ro bene m core, color specified. Connector fabricated from 1.250" O.D. 6063-T6 aluminum. (� E; 70� o Clamps: Cast aluminum. Finish: ProShield, color specified. _ Barrier: Weldment comprised of 1.125' (28,58 mm) O.D. x 11 GA (.120") (3,04 mm) steel tube per ASTM A513 with 203 or 303 stainless steel welded inserts with 5/8" (15,88 mm) internal threads and 1/4" (6,35 mm) tabs. Finish: TenderTuff, color specified. -------------------- 152907B Deck Link wBarriers Steel infill panel 2 Steps Barrier: Weldment comprised of 1.125' (28,58 mm) O.D. x 11 Ga. (.120") (3,04 mm) wall steel tubing, 5/8" (15,88 mm) O.D. steel bar with 203 or 303 stainless steel 3/8" (9,53 mm)threaded inserts. Finish: TenderTuff, color specified. Step Section: Formed from 12 GA (.105') (2,66 mm) sheet steel comforming to ASTM A 1011. Standing surface is 24 1/4" (615,95 mm) wide x 14" (356 mm) deep and is perforated with 5/16" (7,94 mm) diameter holes. Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Clamps: Cast aluminum. Finish: ProShield, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16"(42,85 mm). Finish: ProShield, color specified. Stee1X Panels: Zinc plated 7 GA (.179") (4,55 mm) HRPO flat steel. Finish: ProShield, color specified. 176077B Croquet Climber 72"Dk DB Clamps: Cast aluminum. Finish: ProShield, color specified. 03500-18 Croquet Climber: Weldment comprised of 2.375' (60,33 mm) O.D. RS20 (.095"-.105") (2,41 mm -2,66 mm) wall galvanized steel tube, 1.029" (26,13 mm) O.D. RS20 (.070"-.080") (1,78 mm -2,03 mm) wall galvanized steel tube, and 1/4" (6,35 mm) HRPO steel sheet. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. 176078A Lollipop Climber 48"Dk DB Handhold Panel: Permalene, color specified. Handhold Panel: Permalene, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Lollipop Climber: Weldment comprised of 1.315' (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,28 mm) wall galvanized steel tube, 2.375' (60,33 mm) O.D. RS20 (.095'-.105') (2,41 mm -2,66 mm) wall galvanized steel tube, 1/4"(6,35 mm) HRPO steel sheet and 10 GA. (.13511) (3,43 mm) HRPO steel. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16"(42,85 mm). Finish: ProShield, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. -------------------- N O 176079A ` o Sunbeam Climber t r Clamps: Cast aluminum. Finish: ProShield, color specified. _ Panels: Permalene, color specified. F d Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 03500-19 Handloop: Weldment comprised of 1.125' (28,58 mm) O.D. x 11 GA (.120") (3,04 mm) steel tubing with 203 or 303 stainless steel inserts, with 3/8" (9,53 mm) internal thread. Finish: TenderTuff, color specified. Barrier: Weldment comprised of 1.125' (28,58 mm) O.D. x 11 GA (.120") (3,04 mm) steel tube per ASTM A513 with 203 or 303 stainless steel welded inserts with 5/8" (15,88 mm) internal threads and 1/4" (6,35 mm) tabs. Finish: TenderTuff, color specified. Sunbeam Climber: Weldment comprised of 1.315' (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,28 mm) wall galvanized steel tube, 2.375' (60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm -3,56 mm) wall 49vanized steel tube, and 1/4" (6,35 mm) HRPO steel sheet. Finish: ProShield, color specified. o cn T -------------------- ni r 200609A c t� cn 1 Traveler Climber w/2 Hanger Brackets 3 0 �7. O Handhold Panel: Recycled Permalene, color specified. y Trapeze Bar: Weldment comprised of 1.315' (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,29 mm) galvanized steel tubing and 7 GA. (.179") (4,55 mm) HRPO steel sheet. Finish: ProShield, color specified. Cable Assy.: (Cable) Made of tightly woven polyester -wrapped, six -stranded galvanized -steel cable with a polypropylene core. (Cable Connectors) 6063-T6 aluminum. Net Clamp: Weldment comprised of 1/4" x 13/4" (6,35 mm x 44,45 mm) HRPO flat steel and .375' (9,53 mm) stainless steel sheet. Finish: ProShield, color specified. Belt: Made from .315' (8,00 mm) thick mini rough top 3 -ply rubber belting with polyester fabric plys, black in color. Attachment Brkt: Formed from 3/16" HRPO low carbon steel. Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). GripX Tread: 3/4" (19,05 mm) Thick Permalene®, black in color. Belt Tab: Weldment comprised of 3/8" (9,53 mm) thick HRPO steel sheet, and 1/4" (6,35 mm) HRPO flat steel. Finish: ProShield, color specified. Lower Beam: Weldment comprised of 1.900 (48,26 mm) O.D. RS20 (.090"-.100") (2,29 mm -2,54 mm) galvanized steel tubing, 1.315 (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,29 mm) galvanized steel tubing, 7 GA. (.179") (4,55 mm) HRPO steel sheet, 1/8" (3,18 mm) HRPO steel sheet and 3/8" (9,53 mm) thick HRPO steel sheet. SAE 841 dry bronze bushings are pressed into housings at factory. Finish: ProShield®, color specified. Support: Weldment comprised of 2.375' (60,33 mm) O.D. RS40 (.130" - .140") (3,30 mm -3,56 mm) wall galvanized steel tubing,3/8" (9,53 mm) thick HRPO steel sheet, and 1/4" (6,35 mm) HRPO flat steel. Finish: ProShield, color specified. 03500-20 111228A Square Tenderdeck Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Square Deck: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A 1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face mounting components. The finished size measures 2 5/8" x 47" x 47" (66,68 mm x 1194 mm x 1194 mm). Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 111229A Square Deck Extension Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Square Deck Extension: Flange formed from 12 GA (.105') (2,66 mm) sheet steel conforming to ASTM A1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face mounting components. The finished size measures 2 5/8" x 42" x 47" (66,68 mm x 1067 mm x 1194 mm). Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 119646A Tri -Deck Extension Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. N O Triangular Deck Extension: Flange formed from 12 GA (.105') (2,66 mm) sheet steel colgprminf o ASTM Al 011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face baCe sIcRd holeT I' for face mounting components. The finished size of two of the three sides measures 2 5/8t- 7/" (66,65_- mm x 962,03 mm) on the face of the deck and the other side measures 2 5/8" x43 3/4" (n4 111 >j,"ZS mm). Finish: TenderTuff, color specified.{ m a z Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless I ( T) peO ASTM F 879 unless otherwise indicated (see specific product installation/specifications) r CO 03500-21 122197A 90t Triangular Tenderdeck Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified Triangular Deck: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face mounting components. The finished size measures 2 5/8" x 37 3/4" (66,68 mm x 958,85 mm). Finish: TenderTuff, color specified. o_ v `" Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainlesifsiRl ( ) per in ASTM F 879 unless otherwise indicated (see specific product installation/specifications).:> �. m -------------------- m p rn 152911 0 0 C:) a - Curved Transfer Module Left 48"Dk DB Deck Support: Weldment comprised of 3 1/2" (88,9 mm) O.D. RS -20 (.125") (3,17 mm) galvanized steel tubing and 3/8" (9,53 mm) O.D. x 5" (127 mm) long CRS rod. Finish: ProShield, color specified. Deck: Flange formed from 12 GA (.105") (2,66 nun) HRPO sheet steel conforming to ASTM AIOl 1. Standing surface is perforated with 5/16"(7,92 mm) diameter holes and measures 29" (737 mm) per (2) sides. Finish: TenderTuff, color specified. Panels: Permalene, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Railings: Weldment comprised of 1.125' (28,58 mm) O.D. x 11 GA. (.120") (3,04 mm) steel tubing with 203 or 303 stainless steel 3/8" (9,53 mm) threaded inserts. Finish: TenderTuff, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Step Support: Weldment comprised of 1.660" (42,16 mm) O.D. RS -20 (.080" -.095") (2,03 mm -2,41 mm) galvanized steel tubing and 13/4" x 13/4" x 1/8" (44,45 mm x 44,45 mm x 3,17 mm) HR angle. Finish: ProShield, color specified. Step Sections/Top Step Section: Formed from 12 GA (.105') (2,66 mm) HRPO sheet steel conforming to ASTM A1011. Standing surface is 24 3/8" (619,13 mm) wide x 14" (355,6 mm) deep and is perforated with 5/16" (7,92 mm) diameter holes. Finish: TenderTuff, color specified. 116244B Pipe Barrier w/Wheel Above Deck 03500-22 Wheel: 12" (305 mm) diameter cast A319.1 aluminum alloy. Shaft -303 stainless steel. Finish: TenderTuff, color specified. Wheel Clamp: Formed from 3/16" x 2" (4,75 mm x 52 mm) HRPO zinc -plated. Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Pipe Barrier: Weldment comprised of 5/8" (15,88 mm) solid steel vertical rails, 1 1/8" (28,58 mm) O.D. x 11 GA (.120") (3,04 mm) steel horizontal rails with 203 or 303 stainless steel welded inserts with 5/8"(15,88 mm) internal threads, 1 1/2" x 1 1/2" x 29 1/2" (38,1 mm x 38,1 mm x 749,3 mm) angle iron. Barrier measures 33 7/8" (860,43 mm) wide x 39 13/16" (1011,22 mm) high. Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 90o Bracket: Formed from 1/4" x 1 1/4" (6,35 mm x 31,75 mm) HRPO flat steel. Finish: ProShield, color specified. 116244A Pipe Barrier Above Deck Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Pipe Barrier: Weldment comprised of 5/8" (15,88 mm) solid steel vertical rails, 1 1/8" (28,58 mm) O.D. x 11 GA (.120") (3,04 mm) steel horizontal rails with 203 or 303 stainless steel welded inserts with 5/8" (15,88 mm) internal threads, 1 1/2" x 1 1/2" x 29 1/2" (38,1 mm x 38,1 mm x 749,3 mm) angle iron. Barrier measures 33 7/8" (860,43 mm) wide x 39 13/16" (1011,22 mm) high. Finish: TenderTuff, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 90o Bracket: Formed from 1/4" x 1 1/4" (6,35 mm x 31,75 mm) HRPO flat steel. Finish: ProShield„ tOlor specified. o ® C) `- -------------------- 117957A =tn :'tom a Periscope Panel Above Deck71 Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. a Mounting Plate: Fabricated from formed 11 GA (.120") (3,04 mm) HRS. Finish: ProShield, red in color. i3 r M. Cy Angled Panel Bracket: Weldment comprised of .190" (4,83 mm) thick 5052 aluminum formed angle with (2) 6005-T5 aluminum threaded tubes 1 1/8" (28,58 mm) O.D. x 1 1/2" (38,1 mm) long. Finish: ProShield, color specified. 03500-23 Periscope Assembly: Fabricated from an octagon 14 GA (.075") (1,91 mm) steel tube ProShield red with (2) 18 GA (.048") (1,22 mm) 304 stainless steel bright annealed (reflective finishes). Periscope rotates vertically and horizontally. Permalene: Hand -grip and lense covers are black in color. Permalene Panel: Two color panel measures 35 5/8" (904,88 mm) wide x 41" (1041 mm) high, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16" (42,85 mm). Finish: ProShield, color specified. *11011470 Match 3 Reach Panel Ground Level N b Access Clamp: Weldment comprised of 3/8" (9,53 mm) HRPO steel plate and 1/4" x 1 3/4';x,35 x 44,45 mm) wide steel clamp. Finish: ProShield, color specified. cc? 3> __j Angle: Fabricated from formed 11 GA (.120") (3,04 mm) HRPO sheet steel. Finish: ProShieR joloa% r specified. �m p M A 0 Panel: Two color panel measures 34" (864 mm) wide x 14" (356 mm) high, color specified.:) o 3> Aluminum Rod: 1/2" x 12 5/8" (12,7 mm x 320,68 mm) aluminum rod. _ Half Clamp: Cast aluminum. Finish: ProShield, color specified. Pivot Blocks: U.V. stabilized high-density polyethylene, tan on one side and brown on the other. Rod Cover: One -color Permalene, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 173591A OmniSpin Spinner Surface Mount OmniSpin Spinner: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. OmniSpin Spinner Frame Assembly: (Frame) Weldment comprised of 2.375" (60,33 mm)O.D. RS20 (.095"- .105") (2,41 mm -2,66 mm) wall galvanized steel tubing, 2.875" (73,03 mm) O.D. RS40 (.160"-.170") (4,06 mm -4,32 mm) wall galvanized steel tubing, 1/4" (6,35 mm) HR flat steel and 3 1/2" (88,9 mm) O.D. CF steel bar. (Base) Weldment comprised of 3/8" (9,53 mm) HRPO sheet steel and 3/16" (4,75 mm) HRPO sheet steel. (Shock Covers) 16 GA (.060") (1,52 mm) HRPO sheet steel. (Crank Arms & Pins) Fabricated from stainless steel. (Shocks) Gas shocks with fixed bearings. Finish: ProShield, black in color. 03500-24 Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 185927A Flywheel Spinner DB Only Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installationtspecifications). Flywheel Spinner: Rotationally molded from U.V. stabilized linear low density polyethylene measuring 47 1/2" (1206 mm) wide x 12 1/2" (317 mm) high, color specified. Flywheel Spinner Assembly: (Wheel) Weldment comprised of 1.315' (33,4 mm) O.D. RS20 (.080"-.090") 2,03 mm -2,28 mm) wall galvanized steel tubing, 1/4" (6,35 mm) thick HRPO steel sheet and 3.500" (88,9 mm) O.D. steel pipe. Finish: ProShield, color specified. (Bearings) 2" (50 mm) Deep groove stainless steel. 0 Flywheel Spinner Post: Weldment comprised of 3.500" (88,9 mm) O.D. RS20 (.125') (107 mmall galvanized steel tubing, 1/8" (3,17 mm) thick HRPO steel plate and 1.967' (49,96 mm) Oeel ft. Ti Finish: ProShield®, color specified. C-) � r -------------------- -r p rn s 186490A We -saw DB Only w Anchor Cage: Weldment comprised of 1.029" (26,13 mm) O.D. RS20 (.070"-.080") (1,77 mm - 2,03 mm) wall galvanized steel tubing with 203 or 303 stainless steel welded inserts with 5/8" internal threads and 7 GA. (.179") (4,54 mm) HRPO steel sheet. Finish: Proshield®, black in color. We -saw Assembly: (Arm Assembly) Weldment comprised of 3.500" (88,9 mm) O.D. x 8 GA. (.162") (4,11 mm) wall galvanized steel tubing, 2.375' (60,33) O.D. RS40 (.130"-.140") (3,30 mm -3,56 mm) wall galvanized steel tubing, 1.900" (48,26 mm) O.D. RS40 (.120"-.130") (3,05 mm -3,30 mm) wall galvanized steel tubing, .375' (9,52 mm) thick HRPO steel plate and .250" (6,35 mm) HRPO steel plate. Finish: Proshield®, black in color. (Rocker Assembly) Weldment comprised .250" (6,35 mm) HRPO steel plate and 2" (50 mm) x 5/16" (7,93 mm) wall steel tubing. Finish: ProShield, black in color. (Base) Weldment comprised .375' (9,53 mm) HRPO steel plate and 2.500"(63,50 mm) O.D. x 1.150" (29,21 mm) I.D. stainless steel tubing. Finish: ProShield, black in color. (Base Plate) Fabricated from .250" (6,35 mm) HRPO steel plate. Finish: ProShield, black in color. (Spring) 5 5/8" (142,87 mm) diameter 13/16" (20,62 mm) tempered alloy steel coil. Finish: ProShield, black in color. (Spring Wedge) Cast from ductile iron alloy. Finish: ProShield, black in color. (Bearings) 1.145' (29,08 mm) I.D. oilite bronze. (Shaft) 1.14"(28,96 mm) O.D. stainless steel. Bumper Footer: Weldment comprised of 1.315' (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm - 2,29 mm) wall galvanized steel tubing with 203 or 303 stainless steel welded inserts with 5/8" internal threads and .250" (6,35 mm) thick HRPO steel plate. Finish: Proshield®, color specified. Center Pad: Fabricated from .250" (6,35 mm) thick HRPO steel sheet plate. Finish: Proshield®, black in color. 03500-25 Filler Plate: Fabricated from 12 Ga. (105") (2,66 mm) HRPO steel sheet. Finish: ProShield, color specified. GripX Insert: 3/4" (19,05 mm) Thick Permalene®, black in color. Teeter Pad & Edges: Permalene®, color specified. Platform Handhold: Weldment comprised of 1.315" (33,4 mm) O.D. RS20 (.080"-.090") (2,03 mm - 2,28 mm) wall galvanized steel tubing, 10 GA (.135") (3, 42 mm) HRPO steel sheet and 7 GA. (.179") (4,54 mm) HRPO steel sheet. Finish: Proshield®, color specified. Rung Cap: Molded from U.V. stabilized black EPDM rubber encapsulating .250" (6,35 mm) thick aluminum sheet and .125" (3,18 mm) thick aluminum plate. Seat: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SSM per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Q v, -------------------- -' 163596A�r�- �. M 12' PlayOdyssey Tower m X a p 0 !r Clamps: Cast aluminum. Finish: ProShield, color specified. - Infill Panel: Recycled Permalene, color specified. Inner Deck Plate: Fabricated from 1/4" (6,35 mm) HRPO steel sheet. Finish: ProShield, color specified. Pipebolt: Fabricated from 1.125" (28,58 mm) O.D. 6061-T6 aluminum tube, with 3/8" (9,53 mm) internal threads. Nylon Spacer: 3/8" (9,53 mm) I.D. nylon washer. Support Bar: Fabricated from 1/4" x 1 1/4" (6,35 mm x 31,75 mm) HRPO flat steel. Finish: ProShield, color specified. Double Post: Weldment comprised of 5" (127 mm) O.D. x 11 GA (.120") (3,04 mm) galvanized steel tubing, 1.029" (26,13 mm) O.D. RS -20 (.070" -.080") (4,51 mm -2,03 mm) galvanized steel tubing, 1.315" (33,40 mm) O.D. RS -20 (.080" -.090") (2,03 mm -2,28 mm) galvanized steel tubing and 1/4" x 1 1/4" (6,35 mm x 31,75 mm) HRPO flat steel. Finish: ProShield, color specified. Infill Deck: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A101 1. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. The finished size measures 2 5/8" x 24 3/8" x 24 3/8" (66,68 mm x 619,13 mm x 619,13 mm). Finish: TenderTuff, color specified. Octagon Deck: Flange formed from 12 GA (.105") (2,66 mm) sheet steel conforming to ASTM A1011. Standing surface is perforated with 5/16" (7,92 mm) diameter holes. Deck face has (4) slotted holes for face mounting components. The combined finished size measures 2 5/8" x 106 1/4" x 106 1/4" (66,68 mm x 2698,75 mm x 2698,75 mm). Finish: TenderTuff, color specified. 03500-26 Outer Post: Fabricated from 5" (127 mm) O.D. x 11 GA. (.120") (3,04 mm) galvanized steel tubing. Finish: ProShield, color specified. Post Extension: Weldment comprised of 4.675" (118,75 mm) O.D. x.150" (3,81 mm) 6065-T5 extruded aluminum, formed 5" (127 mm) O.D. x.125" (3,17 mm) 6061-T6 extruded aluminum and die cast 369.1 aluminum post cap. Finish: ProShield, color specified. Roof Post: Weldment comprised of 4.675" (118,75 mm) O.D. x.150" (3,81 mm) 6061-T6 extruded aluminum and formed 5" (127 mm) O.D. x.125" (3,17 nun) 6005-T5 extruded aluminum. Finish: ProShield, color specified. Poly Roof: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Bubble: Vacuum formed .230" x 26 1/2" (5,84 mm x 673,1 mm) diameter clear polycarbonate 165780B 12' Tower S1ideWindei2 wBarrier Rail Spacer: Fabricated from 1.312" (33,32 mm) O.D. x 16 Ga. (.065") (1,65 mm) steel tubing. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16"(42,85 mm). Finish: ProShield, color specified. Bubble: Vacuum formed .230" x 26 1/2" (5,84 mm x 673,1 mm) diameter clear polycarbonate. Permalene Panel: One -color panel measures 35 5/8" (904,88 mm) wide x 71" (1803 mm) high, color specified. 03500-27 0 165824A 12' Tower Bubble Panel �. �- o — --- Clamps: Cast aluminum. Finish: ProShield, color specified. —rM m Kick Plate: Fabricated from 11 GA. (.120") (3,04 mm). Finish: ProShield, color specified. . a Nylon Spacer: 3/8" (9,53 mm) I.D. nylon washer. w Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16"(42,85 mm). Finish: ProShield, color specified. Bubble: Vacuum formed .230" x 26 1/2" (5,84 mm x 673,1 mm) diameter clear polycarbonate. Permalene Panel: One -color panel measures 35 5/8" (904,88 mm) wide x 71" (1803 mm) high, color specified. 03500-27 No Material Spec for 165827B 165960A 12' Tower Pipe Barrier Clamps: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Tall Pipe Barrier: Weldment comprised of 1.315" (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,28 mm) wall galvanized steel tube with 203 or 303 stainless steel welded inserts with 5/8" (15,88 mm) internal threads, 1 1/2" x 2" x 3/16" (38,1 mm x 51 mm x 4,75 mm) steel angle and 12 GA. (.105") (2,66 mm) steel pipe cap. Finish: ProShield, color specified. 193169B Netplex 14 -Post w/3 -Roofs Steel Posts and DB Only Roof Clamp: Cast aluminum. Finish: ProShield, color specified. Roof: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Rope System Brace: Weldment comprised of 1.900" (48,26 mm) O.D. RS40 (.120"-.130") (3,05 mm -3,30 mm) wall galvanized steel tubing, and 1/4" (6,35 mm) thick HRPO steel. Finish: ProShield, black in color. Post: See PlayBooster (PB) General Specifications. Post Topper: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). No Half Clamp: Steel. Finish: ProShield, black in color.n o -------------------- n m Q- -t n 194659B =� � a m 3 Q Disc Net Climber for 14 -Post Mainstructure D O Cable Assy.: (Cable) Made of tightly woven polyester -wrapped, six -stranded galvanized -steel cable with a polypropylene core. (Cable Connectors) 6063-T6 aluminum. Mat Ring: Perinalene®, color specified. Net Mat: .315"(8,00 mm) Thick mini rough top rubber belting with polyester fabric plys, black in color. 03500-28 Clamp: 369.1 Aluminum. Finish: ProShield®, color specified. Casting Plate: Weldment comprised of 3/8" (9,53 mm) HRPO steel plate and 1/4" (6,35 mm) HRPO steel plate. Finish: ProShield®, color specified. Rubber Mat Fastener: Fabricated from 3/8" (9,53 mm) HRPO steel plate. Finish: ProShield, black in color. Rubber Mat Fastener 2: Fabricated from 1/8" (3,17 mm) HRPO steel plate. Finish: ProShield, black in color. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 166809A E -Pod Seat E -Pod Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Pod: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Pod Casting: Fabricated from sand cast alloy 356 in accordance with ASTM B26. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 0 193174A Hca o Sol Spinner DB i r Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainles§'jlQ (Sff) peT ASTM F 879 unless otherwise indicated (see specific product iristallation/specifications).jE�. r cm Support Arm: Weldment comprised of 2.375' (60,33 mm) O.D. RS40 (.130"-.140")(3,30 mm - 3,56 mm) wall galvanized steel tube, 2.750" (69,85 mm) O.D. 1018 steel, and 1/4" (6,35 mm) HRPO flat steel. Finish: ProShield®, color specified. Sol Spinner: Weldment comprised of 1.900" (48,26 mm) O.D. RS20 (.090"-.100")( 2,29 mm -2,54 mm) wall galvanized steel tube, 1.660" (42,16 mm) O.D. RS40 (.111"-.121 ")(2,82 mm -3,07 mm) wall galvanized steel tube, 1/4" (6,35 mm) HRPO steel plate, 3/8" (9,53 mm) HRPO steel plate, 2.750" (69,85 mm) O.D. 1018 steel, and 17/8" (47,63 mm) steel ball. Finish: ProShield, color specified. GripX Panels: Permalene®, black in color. Bushing: Oil -filled UHMW PE. 03500-29 Footer: Weldment comprised of 2.375"(60,32 mm) O.D. RS40 (.130"-.140") (3,30 mm -3,56 mm) wall galvanized steel tube, 12 GA. (.105") (2,66 mm) HR flat steel and 1 7/8" (47,62 mm) steel ball. Finish: ProShield, color specified. 193176A Boogie Board DB Only Leg Cap: Aluminum. Belt:.315" (8,00 mm) Thick mini rough top rubber belting with polyester fabric plys, black in color. Mounting Plate: Comprised of 3/8" (9,53 mm) thick HRPO sheet steel and 2" (50,8 mm) O.D. x 1.50 " (38,1 mm) I.D. stainless steel housing. Finish: ProShield®, color specified. Shaft Mount: Weldment comprised of 1/4" (6,35 mm) thick HRPO flat steel and 1" (25 mm) diameter stainless steel shaft. Finish: ProShield®, color specified. Panels: Pennalene,color specified. Post: See PlayBooster (PB) General Specifications. Presser Plate: Fabricated from? GA. (.179") (4,54 mm) thick HRPO sheet steel. Finish: ProShield®, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Belt Plate: Weldment comprised or 3/8" (9,53 mm) thick HRPO sheet steel and 1/4" (6,35 mm) thick HRPO sheet steel. Finish: ProShield®, color specified. N O ------------------- 201545AD s Blender Spinner DB ,< rnm rri a Clamps: Cast aluminum. Finish: ProShield, color specified. ED= o Q Clamps: Cast aluminum. Finish: ProShield, color specified. Y' _ Support Arm: Weldment comprised of 2.375' (60,33 mm) O.D. RS40 (.130"-.140"x3,30 mm - 3,56 mm) wall galvanized steel tube, 2.750" (69,85 mm) O.D. 1018 steel, and 1/4" (6,35 nun) HRPO flat steel. Finish: ProShield®, color specified. Bushing: Oil -filled UHMW PE. 03500-30 Footer: Weldment comprised of 2.375' (60,32 mm) O.D. RS40 (.130"-.140") (3,30 mm -3,56 mm) wall galvanized steel tube, 12 GA. (.105') (2,66 mm) HR flat steel and 17/8" (47,62 mm) steel ball. Finish: ProShield, color specified. 193170A LolliLadder w/2 E -Pods LolliLadder: Weldment comprised of 1/4" (6,35 mm) HRPO flat steel, 2.375" (60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm -3,55 mm) wall galvanized steel tubing, and 1.315' (33,40 mm) O.D. RS20 (.080"- .090") (2,03 mm -2,29 mm) wall galvanized tubing. Finish: ProShield®, color specified.. Finish: ProShield, color specified. E -Pod Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Pod: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Pod Casting: Fabricated from sand cast alloy 356 in accordance with ASTM B26. Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Rung Cap: EPDM, black in color. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 111404R 108"Steel Post DB Post: See PlayBooster (PB) General Specifications. o -------------------- 1114040 C") 132"Steel Post DB -.<4. rq Ex a rn �n Post: See PlayBooster (PB) General Specifications.v r rn 111404M 148"Steel Post DB Post: See PlayBooster (PB) General Specifications. 03500-31 111404F 108"Alum Post DB Post: See PlayBooster (PB) General Specifications. 111404D 124"Alum Post DB Post: See PlayBooster (PB) General Specifications. 111404C 132"Alum Post DB Post: See PlayBooster (PB) General Specifications. II1404A 148"Alum Post DB N o s c� o �-a Post: See PlayBooster (PB) General Specifications. D-------------------- tr m a 1795950 a c 0 204"Steel Post For Vibe Roof DB v _ Post: See PlayBooster (PB) General Specifications. 179594A Vibe Roof Roof: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Infill Panel: Made from 12 GA. (.105") (3,18 mm) thick HRPO steel sheet zinc plated. Finish: ProShield, color specified. 03500-32 Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 182503C Welcome Sign (LSI Provided) Ages 5-12 years Direct Bury Sign Panel: Panel is fabricated from 1/8" (.125")(3,17 mm) aluminum plate. Finish: ProShield®, gray in color. (Sign) Digital image is transfered to a 1/8" (.125")(3,17 mm) ProShield coated aluminum plate, then infused into the ProShield. Post: Weldment comprised 2.375" (60,33 mm) O.D. RS20 (.095-.105) (2,41 mm -2,67 mm) wall galvanized tube, 1/4"(6,35 nun) HRPO steel sheet and aluminum post cap. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 124863F SlideWinder2 72"Dk DB 1 Straight 1 Right 1 Left Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Rail Spacer: Fabricated from 1.312" (33,32 mm) O.D. x 16 Ga. (.065") (1,65 mm) steel tubing. Finish: ProShield, color specified. Rail: 1 1/8" (28,58 mm) O.D. 6061-T6 aluminum extrusion with 5/16" (7,92 mm) walls. Finish: ProShield, color specified. Slide Sections: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. N Exit Footer: Weldment comprised of 2.375" (60,33 mm) O.D. RS -20 (.095"-.105") (2,41 MM -2,66%m) galvanized steel tubing and 1/4" x 3" x 7 1/2" (6,35 mm x 76 mm x 191 mm) HRPO steelyntina date. — Finish: ProShield, color specified. 1--y -4 Mid -Support: Weldment comprised of 1.900" (48,26 mm) O.D. RS20 (.090"-.100") (2,28` Ski m) m galvanized steel tubing and 7 GA. (.179") (4,54 m) HRPO steel strap. Finish: ProShield, Lsp = ed. m Support Base (SM): Weldment comprised of 1.660" (42,16 mm) O.D. RS -20 (.085" -.095' 6 nQ-2,41 mm) galvanized steel tubing and 1/4" x 3" x 8" (6,35 mm x 76 mm x203 mm) mounting pl t5 e. Finig. ProShield, color specified. 03500-33 144414A Cloudburst Triple Slide 72"Dk DB Mid -Support: Weldment comprised of 1.660" (42,16 mm) O.D. RS -20 (.085' -.095") (2,16 mm -2,41 mm) galvanized steel tubing and 1/4" x 3" (6,35 mm x 76 mm) mounting plate. Finish: ProShield, color specified. Rail: Extruded from 1.125' ((28,58 mm) O.D. x.312" (7,92 mm) wall. 6005-T5 aluminum. Finish: ProShield, color specified. Hood: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Exit Support: Weldment comprised of 2.375' (60,33 mm) O.D. RS -20 (.095' -.105") (2,41 mm -2,66 mm) galvanized steel tubing and 1/4" x 3" (6,35 mm x 76 mm) mounting plate. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Rail Spacer: Fabricated from 1.312" (33,32 mm) O.D. x 16 GA (.065') (1,65 mm) steel tubing. Finish: ProShield, color specified. Slide: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/8" (22,23 mm) O.D. x 1 11/16"(42,85 mm). Finish: ProShield, color specified. ti a -------------------- ov 189313A n..{ I �n Rushwinder DB Right ; t rn p rn C5 Hood: Rotationally molded from U.V. stabilized linear low density polyethylene, color speia s Q Vertical Ladder: Weldment comprised of 2.375' (60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm -3,56 mm) wall galvanized steel tubing, and 1.315' (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,29 mm) wall galvanized steel tubing and 1/4" (6,35 mm) HRPO flat steel,. Finish: ProShield®, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Slide Sections: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified Exit Footer: Weldment comprised of 2.375' (60,33 mm) O.D. RS -20 (.095' -.105") (2,41 mm -2,66 mm) galvanized steel tubing and 1/4" x 3" x 7 1/2" (6,35 mm x 76 mm x 191 mm) HRPO steel mounting plate. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Mid -Support: Weldment comprised of 1.900" (48,26 mm) O.D. RS20 (.090"-.100") (2,28 mm -2,54 mm) galvanized steel tubing and 7 GA. (.179") (4,54 mm) HRPO steel strap. Finish: ProShield, color specified. 03500-34 Crossover: Weldment comprised of 2.375" (60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm -3,56 mm) wall galvanized steel tubing, and 1/4" (6,35 mm) HRPO flat steel. Finish: ProShield, color specified. Hand Grip: Weldment comprised of 1.315" (33,4 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,28 mm) wall galvanized steel tubing and 7 GA. (.179") (4,54 mm) HRPO steel sheet. Finish: ProShield, color specified. -------------------- 173592A Oodle Swing DB Only Bumper: Molded from U.V. stabilized black EPDM rubber encapsulating i 1 GA (.120") (3,04 mm) HRPO steel sheet. Cable: Made of tightly woven polyester -wrapped, six -stranded galvanized -steel cable with a polypropylene core. (Cable Connectors) 6061-T6 aluminum. Swing Seat Brkt: Weldment comprised of 1.66" (42,16 mm) O.D. RS20 (.085"-.095") (2,16 mm -2,41 mm) wall galvanized steel tube, 1.000" (25,4 mm) O.D. x .750" (19,05 mm) I.D. 1018 steel tube and 7GA (.179") (4,55 mm) HRPO steel sheet. Finish: ProShield®, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Swing Beam Assy.: Weldment comprised of 3.500" (88,9 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,28 mm) wall galvanized steel tube and 1/2" (12,7 mm) thick stainless steel tabs. Finish: ProShield, color specified. Swing Hanger Assembly: Assembly comprised of 300 series stainless steel knuckle and yoke, stainless steel swing pin, stainless steel spring pin and oilite bushings. Swing Leg: 3.500" (88,9 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,28 mm) wall galvanized steel tube. Finish: ProShield, color specified. Swing Seat: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified 174018A o Belt Seat ProGuard Chains for 8' Beam Height o) Zj Bolt Link: Stainless Steel c*II c7 m r Belt Seat: Molded from UV stabilized black EPDM rubber encapsulating a weldment coed a'& 22 (.029") (0,74 mm) spring stainless steel sheet and (4) .105" (2,67 mm) thick stainless ste;V06shew The seat elliptical shape measures 7" (178 mm) wide x 26" (660 mm) long x .700" (17,78 mingPthick. F- CR Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 03500-35 Chain/ProGuard: Steel 3/16" (4,75 mm) straight link chain, 800 Ib. (362,87 kilograms) working load limit. Finish: ProGuard. 176038A Full Bucket Seat ProGuard Chains for 8' Beam Height Full Bucket Seat: Made of U.V. stabilized high-quality black rubber encapsulating a 24 GA (.024") (0,61 mm) stainless steel reinforcement plate. Handles cast from 356-T6 aluminum alloy with black polyarmor paint finish. Handles attach to seat with (3) 1/411(6,35 mm) x 1 5/16" (33,32 mm) long stainless steel rivets. The full bucket measures 9" (229 mm) deep x 10 1/2" (266,7 mm) wide. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Chain/ProGuard: Steel 3/16" (4,75 mm) straight link chain, 800 Ib. (362,87 kilograms) working load limit. Finish: ProGuard. 177332A Single Post Swing Frame 8' Beam Height Only Beam: Weldment comprised of 2.375" (60,33 mm) O.D. RS40 (.130" -.140") (3,30 mm -3,56 mm) galvanized steel tubing, 3" (76 mm) wide zinc -plated steel clamps and 1 1/4" (31,75 mm) housings w/bronze bushings. Finish: ProShield, color specified. Half Clamp: Cast aluminum. Finish: ProShield, color specified. d Post: See P1ayBooster (PB) General Specifications.—n a� Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless QgeWST�per r ASTM F 879 unless otherwise indicated (see specific product installation/specifications). C")rn m ss = 177333A Single Post Swing Frame Additional Bay 8' Beam Height Only Beam: Weldment comprised of 2.375" (60,33 mm) O.D. RS40 (.130" -.140") (3,30 mm -3,56 mm) galvanized steel tubing, 3" (76 mm) wide zinc -plated steel clamps and 1 1/4" (31,75 mm) housings w/bronze bushings. Finish: ProShield, color specified. Half Clamp: Cast aluminum. Finish: ProShield, color specified. Post: See PlayBooster (PB) General Specifications. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). 03500-36 177351A Molded Bucket Seat w/Hamess ProGuard Chains for 8' Beam Height Dbl. Pivot Block: Fabricated from 6061-T6 Aluminum with bronze oil impregnated bearing. Bumper: Molded from U.V. stabilized black EPDM rubber encapsulating 11 GA (.120") (3,04 mm) HRPO steel sheet. Mounting Bracket: Cast from 535 aluminum magnesium. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Chain/ProGuard: Steel 3/16" (4,75 mm) straight link chain, 800 lb. (362,87 kilograms) working load limit. Finish: ProGuard. Bucket Seat Assy: (Bucket Seat & Yoke) Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. (Pipebolt) Made from 1.125" (28,58 mm) O.D. 6005-T5 threaded anodized aluminum tube. (Bearings) UHMW PE lubricated. (Brackets) Made from 356-T6 aluminum. Warranty: You have our word More than just a contract, our warranty is our personal commitment that you'll be satisfied with your purchase now and well into the future. As an employee -owned company we take great pride in the quality of everything we make. And we're so confident that you'll be delighted with your purchase that we back our products with the most comprehensive long-term warranties in the industry. It's just one more way that we show how much we care about our customers and communities. N 100 -YEAR LIMITED WARRANTY �n On all PlayBooster®, PlayShaperg and P1aySense8 aluminum posts, stainless steel faste�larR beast j and caps, against structural failure due to corrosion/natural deterioration or manufacturin ts,-add on PlayBooster, EvosT" and WeevosTM steel posts and arches against structural failure due toa(na6rial manufacturing defects. -4n -G t- r, 15 -YEAR LIMITED WARRANTY C', vp On all plastic components (including TuffFimbersTM edging), all steel components (except_ue yea eel posts), Mobiusg climbers, decks and TenderTuffrM coatings (except Wiggle Ladders, Chain LaddeFmnd Swing Chain) against structural failure due to material or manufacturing defects. TutiFurfg tiles against material or manufacturing defects. ]0 -YEAR LIMITED WARRANTY On concrete products against structural failure due to natural deterioration or manufacturing defects. Does not cover minor chips, hairline cracks or efflorescence. 8 -YEAR LIMITED WARRANTY On AeronetTM climbers and climbing cables against defects in materials or manufacturing defects. On CoolToppersg fabric against failure from significant fading, deterioration, breakdown, mildew, outdoor heat, 03500-37 cold or discoloration. This warranty is limited to the design loads as stated in the specifications found in the technical information. 3 -YEAR LIMITED WARRANTY On all other parts, i.e.: CableCore® products, swing seats and hangers, grills, Mobius climber handholds, Wiggle Ladders, Chain Ladders and Swing Chain, Track Ride trolleys and bumpers, all rocking equipment including Sway Fun® gliders, PVC belting material, HealthBeatTm hydraulic cylinders, Seesaws, Wiggle Ring Bridge, etc., against failure due to corrosion/natural deterioration or manufacturing defects. This warranty does not include any cosmetic issues or wear and tear from normal use. It is valid only if the playstructures and/or equipment are erected to conform with Landscape Structures' installation instructions and maintained according to the maintenance procedures furnished by Landscape Structures Inc. For a full text of the warranty, contact your playground consultant. 03500-38 N 0 C7 ::::q O -n1 c, r r- `<rrt a rn o::O y� x o Q 03500-38 SECTION 03600 INSTALLATION 03600-1 CD CD a a m �� to D � p 03600-1 110070 is the Site Plan Not an Install doc. N O C7 U� 0 71 d i T 9/& landscape structures® 3/3 X 1 t/a. BHCS w/Pin 1/,' X 3/;' Drive Rivet 5" Half SAFETYNOTE Choose a protective swfadrg material lhet ��//�� ++ww//��//��+ pas a Critical Height Value M et least the 'Sy 1,4001 , hHegM ofeight lNeacjacentequipmethe Highest M l(Rel. STaM Certified F1487) 3-1-94 11002200 3/a' Tee Nut 5" O.D. Horizontal Beam I 1 I 5" O.D. 1 Post I I I I L — — F n 0 c; o f c> G 1 rn �� cD G r co Tee Clamp Assemb �+ 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 (763) 972-3391 1-888-LSI-INST (1-888-574-4678) FAX (763) 972-3185 MINtitshoserVad Document #11002200 kk landscape structures, JASPECS\110\11002200.Pa5 Parts List Parti! Description 105327-01 5" Half Clamp, Specify Color 100198-00 '/s' x I '/d' BHCS w/Pin, SST 100351-00 '/1" Tee Nut, SST ..................... 100610-00 x Y." Drive Rivet, SST .... Qty .. 2 .. 4 .. 4 .. 2 Specifications Tee/Beam: 356 alloy treated to T-6 hardness and welded to 5" aluminum beams or mechanically fastened to 5" steel beams. Finish: Powdercoat, color specified. Half Clamps: Cast aluminum. Finish: Powdercoat, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) MASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx.'/tmanhour Weight: 2 lbs. PlayBooster°Tee Clamp Assembly Installation Instructions 1) Locate and mark center of clamp location on 5" pipe 2) With beam in position, fasten 5" half clamps to tee clamp using'/a" x 1 1/e" BHCS w/Pin and tee nuts as shown. Tighten cap screws evenly. 3) IMPORTANT- Install drive rivets in half clamps by drilling holes in clamps and into 5"pipe using a '/,"or F"(only) drill bit. Insert rivet in hole, and hammer rivet pin in until it is flush with head N M t rn 115176 is a hard surface label Not an Install doc. C, C:) C7 _I �-m L t CO U� landscape structures• L mounting will not work in all tions. Consult Landscape es Inc. for your particular re- nts. CONCRETE SLAB SPECS • Base under slab to be 4" - 6" of sand over a stable subgrade. • Depth of concrete slab to be 4" - 6" with a wire mesh support. • Minimum of 7 days curing time full cure after 30 days. • Surface of concrete to be trowled smooth and acid etched. • Concrete: 3000 PSI (Min) 30 Days 3500 PSI 3/, Minus Crushed Rock NOTE: Sufficient protec- tive surfacing must cover hardware to satisfy fall height requirements. NOTE: Drill 3" deep hole using hammer drill and %"masonry bit. Tap anchors Into concrete and secure with 1/2" standard hex nuts and'/," flat washers. 1 1 1 CERTIFIED 200 6% SAFETY NOTE Goose a plolec�va surletlrg malenal That hes a Cnucal Haight Value of al least Ne height of the Highasl Accessible ParUFall 11egh1 ofpe a4acenl eR,npnrent. (Rat ASTM FfiB� 329-01 12194700 31," x 8" Square Steel or Aluminum Plate Continuously Welded to Upright Post DETAIL (4)'/," Standard Hex Nuts (4)'/p plat Washers Upright (4)1/,' x 2 a/," Post Expansion Anchors -----------I Surface ayBooster° Concrete Specs, Surface Mount ca 0 20]1 by LBMsf pi, SVuctums All rights mseNa4 1-309) Ih,cumcm CI21Y�)Illl rq.lecxa Cn �-- rn ¢�' x r Co ayBooster° Concrete Specs, Surface Mount • 0 20]1 by LBMsf pi, SVuctums All rights mseNa4 1-309) Ih,cumcm CI21Y�)Illl rq.lecxa tlla9']IUW_Ilplaari nolfn Document #12194700 U landscape structures - 1/ 42" 42" 1070 1070 A A C 40" Deck SAFETY NOTE Choose a protective surtadng material Ihel has a Critical Height Value of at leael the height of iha Highmt Accessible PaNFell HegMof Na atljaCeMequipmeM (Rel ASTM F1087, SECTION 9) Enclosures or components are required on any decks higher than 28" as indicated on your plan drawing. 32" I v J ao Dimension indicates center to center spac- ing of concrete footings. C Number indicates height of deck above fin- ished grade. 40"_ I NI P '10 Letter indicates post length as indicated on B C your plan drawing. Enclosures/ Components - Refer to your plan drawing for locations and their respec- tive spec sheets for installation. Vertical Ladders - Refer to your plan draw- ing for locations and the Vertical Ladder spec sheet for installation. / Decks - Refer to your plan drawing for O heights and orientation. Refer ,the appro- priate deck spec sheet for inst>�tion. vLL y Deck Hanger Clamp.-AfscP�mbly - Refprle the appropriate Deck7;�atnbly79pa sheet 16" for installation." �t — _ m Deck Concrete Footings- far to'the Typical Concrete Footing spec sheet fors stallation. Kick Plates - Refer to your plan drawing for locations and the Kick Plate spec sheet for installation. Information 6-1-95 601 7TH STREET SOUTH, DELAN O, MINNESOTA 55328-8605 (763)972.3391 1.888-LSI-INST (1-888-574-4678) FAX (763)972-3185 Ji] Document #10972201 56" A A 48" B 40" Deck SAFETY NOTE Choose a protective surtadng material Ihel has a Critical Height Value of at leael the height of iha Highmt Accessible PaNFell HegMof Na atljaCeMequipmeM (Rel ASTM F1087, SECTION 9) Enclosures or components are required on any decks higher than 28" as indicated on your plan drawing. 32" I v J ao Dimension indicates center to center spac- ing of concrete footings. C Number indicates height of deck above fin- ished grade. 40"_ I NI P '10 Letter indicates post length as indicated on B C your plan drawing. Enclosures/ Components - Refer to your plan drawing for locations and their respec- tive spec sheets for installation. Vertical Ladders - Refer to your plan draw- ing for locations and the Vertical Ladder spec sheet for installation. / Decks - Refer to your plan drawing for O heights and orientation. Refer ,the appro- priate deck spec sheet for inst>�tion. vLL y Deck Hanger Clamp.-AfscP�mbly - Refprle the appropriate Deck7;�atnbly79pa sheet 16" for installation." �t — _ m Deck Concrete Footings- far to'the Typical Concrete Footing spec sheet fors stallation. Kick Plates - Refer to your plan drawing for locations and the Kick Plate spec sheet for installation. Information 6-1-95 601 7TH STREET SOUTH, DELAN O, MINNESOTA 55328-8605 (763)972.3391 1.888-LSI-INST (1-888-574-4678) FAX (763)972-3185 Ji] Document #10972201 U vUl. landscape structures- J'ISPECa1109t109=1.Pa5 PlayBooster General Post/Tenderdeck Information Installation Instructions Before Starting, Read the General Construction Guidelines, Installation Hints, All Typical Detail Sheets and Specific In- stallation Instructions for Each Component Labeled on Your Plan. I ) Dig footing holes spaced as shown on the plan and spec sheets. Re- fer to the Typical Concrete Footing Spec Sheet. 2) Note the post lengths as shown on the plan and set in their appmpri- ate footing holes. The post length is indicated on the finished grade sticker on each post. 3) Mark the appropriate posts for the deck heights you are installing and attach decks to posts at marked height. Refer to the appropriate deck spec sheet for installation. 4) After all the posts are at proper heights and plumb, and the decks are at proper height and level, pour the concrete footings per the Typical Concrete Footing Spec Sheet. 5) Continue installing enclosures and components and pour concrete footings as you progress, making sure everything is plumb and level. 6) When installation is complete, install Drive Rivets in all clamps per the Typical Offset Hanger Clamp Spec Sheet. 7) Install protective surfacing under and around all equipment before users are allowed to play on the structure. 6145 nnisi 1 upd Deaw - 0 CID 4' C:3 p� I VD CO p O a/. landscape structures° Rails A Same Height DETAIL ASSEMBLED CLAMP ORaet H Clamp I (2)'/," Tee Nu '/W. x 2 1/: BHCS w/Pin Offset Hanger Clamp NOTE: Position with offset fac- ing down as shown. See De- tail for special applications. Q �� The Offset Hanger Clamp allows rails to be Installed at same height for special applications, like at 900 to each other as shown, or when there are clamp conflicts, offset can be positioned upward. SAFETY NOTE Clause a prvlectrve h0ixi , material that Me a Critical Height Vale 0 et least the height of the Highest Accessible Pan,Fall Ikight tithe adjac tepee t(Ret ASTM F1181) 10-3-97 12382100 NOTE: A drive rivet is not required In all applications. See Drive Rivet Addendum for a listing of components that do not re- quire drive rivets. '14" x'/e' Drive Rivet KP 114261 Offset Hanaer Clamp Assei (2)3/e1x 1 t/s, BHCS w/Pin 10 0 1%7 by Landscape S = es All rights reserved Document #12382100 r.a 0 G' tr Mr rn O_1 to p � rn 10 0 1%7 by Landscape S = es All rights reserved Document #12382100 ti ) PlayBooster 114261 Offset Hanger Clamp Assembly landscape structures' J\SPECS\123\123921 O K5 Parts List Installation Instructions Part# Description Qty 100198-00 '/a" x 1 '/s" BHCS w/Pin, SST .................................... 2 100351-00 '/e" Tee Nut, SST ......................................................... 2 100610-00 '/," x 5/e" Drive Rivet, AUSST................................... 1 103327-01 5" Half Clamp, Specify Color ..................................... 1 113729-00 Offset Hanger Clamp, Specify Color ......................... 1 100203-00 5/e" x 2 '/f BHCS w/Pin, SST .................................... 1 Specifications Clamp: Cast aluminum. Finish: Powdercoat, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx.1/,manhour Weight: 3 lbs. 1) Locate and mark position of clamp on 5" post. 2) Position clamp in proper direction and assemble with %" x 1 1/8" BHCS w/pin arid 14" tee nuts as shown and lightly tighten. Position nil against clamp and screw in %" x 2'/," BHCS w/pin until rail bottoms out on clamp. Final tighten all fasteners. 3) IMPORTANT: Drill through hole in 5"haljclamn and into 5"post with a 4," or F" (only) drill bit, insert rivet in hole and hammer rivet pin in until it isJlurh with head. Q 4� D —1 n � �C-) <r m E5= Z� D 10.3-97 Dxwrcnl M13382I-00 replem kl ldblb-W. Added Dnvr Rivn NOTE: IS& landscape structures° SAFETY NOTE Choose a pmlecUve wladrp material Bbl has a Crieeal Height Value of m least the height of the Hgheal Accessible PaNFall FleigMa/tl�e agaoentegYprtbix (RN.ASTM F16B71 11-22-99 129847a0 129847b0 General Rules For Use Of Drive Rivets • Rivets are used as "Insurance" to keep clamps from sliding down the posts. In many cases this "Insurance" is achieved in other ways; i.e. Panels that attach to the deck face. • Refer to the Spec Sheet Parts List and follow Installation In- structions for each component. • Decks and Overhead Events always need rivets. • Any component fastened to the Deck does not need rivets. Typical Steel Half Clamp Rivet P\in- 7P— Benefits of not installing unnecessary rivets: saves time, it makes clamp adjustments as well as the removal of clamps for replacement or adding phases much easier, and you will have fewer damaged clamps or posts due to poor installation techniques. Typical PlayBooster Post Typical Aluminum Half Clamp , Rivet Pin STEEL t/,' X a/a" Dr Drive aRivet CLAMPS 1101061p1vet 100611 '/4" H CLAMPS INSTRUCTIONS: NOTE: Use Only Bit Size "F' or 1/4" Drill Bit. After Play Component Assembly is Complete, Drill Hole into Post Through Half Clamp, Insert Rivet in Hole, and Hammer Rivet Pin in Until it is Flush with Head. 601 7TH STREETS OUTH, DE LAN O, MINNESOTA 55328-8605 (763) 9723391 1 -888 -LSI -IN ST (1.888.574.4678) FAX (763) 972-3185 Document #12984700 IMPORTANT- Typical Aluminum Half Clamp , Rivet Pin STEEL t/,' X a/a" Dr Drive aRivet CLAMPS 1101061p1vet 100611 '/4" H CLAMPS INSTRUCTIONS: NOTE: Use Only Bit Size "F' or 1/4" Drill Bit. After Play Component Assembly is Complete, Drill Hole into Post Through Half Clamp, Insert Rivet in Hole, and Hammer Rivet Pin in Until it is Flush with Head. 601 7TH STREETS OUTH, DE LAN O, MINNESOTA 55328-8605 (763) 9723391 1 -888 -LSI -IN ST (1.888.574.4678) FAX (763) 972-3185 Document #12984700 S & landscape structures° Post Offset Post Clamp Using Tamperproof Hex Wr h. Hanger Remove Offset Hanger ClamlZ ightl ap Clamp - _r Half 1 �� C�.lanrmp z �X O \ 0 BHCS w/Pin Tee Nut 11-22-99 109729a 1) Drive Center Pin of Rivet Straight into Post Using 48' Diameter Punch and Hammer. 2) Unbolt BHCS w/Pin and Tee Nuts from Clamp Using Tamperproof Hex Wr h. Remove Offset Hanger ClamlZ ightl ap on Half Clamp with Hammer H of Drive Rivet Pulls Away From �ClA14t. - _r A L CT 1 �� rn z �X O 0 3) Pull Out Drive Rivet Using Claw End of Hammer. Tools Needed: • Claw Hammer • V;' Diameter Steel Punch • Tamperproof Hex Wrench RemovalDrive Rivet 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8fi05 7fi3 972-3397 1-888-LSI-INST fiSS857446781 FAX 7fi3 972-3185 120688 is a danger keep off sign Not an Install doc. 0 v CD .<i 1 A �% r 120688 is a danger keep off sign Not an Install doc. �-m r .n 9/& landscape structures" Loose Fill —'y'� •- - - _ Protective - Surfacing Subgrade Concrete Crushed Rods SAFETY NOTE Choose a prWecLve surtaolg material that �/� /�/�+ has a Critical Haight Value of at least the IS014001 , height o he aQae tequ pmeNllRe ASTM Card fI ad F1487) e-2e-00 10970900 Typical Component Support d � A G E E C Minimum 1.2 Cubic Feet of Concrete Required per Support. ' An Example: ff you are using 12" of loose fill material, your concrete footing will be 22" deep. IayBooster Concrete Footings, Components 02oo01hyLarwscama i,mres. Alhghtsreserved xzsaxl ,wn,.naaaa cu�cmer�,.ri�y ama� Document#13237300 SAFETY NOTE choose a hxdedive urfedrg material Mat has a Ctltiwl Height Valve del least t"e .c height of Me Highest Accessible Pa"/Fall N� certl IF F014001 H1081du,e adjamnleginprrleM. (Ref.ASTM landscape1-1-01 structures, PlayBooster Installation 1) Before starting installation, study your PlayBooster plan drawing and all installation instructions carefully for location of posts, deck heights, components and safety enclosures. Make sure slides are oriented away from the afternoon sun and that the structure is visible (easily supervised) and accessible. 2) Clear an area large enough for your PlayBooster and at least the required minimum use zone around it, as shown on your plan drawing. The subsurface must be well drained. If the soil does not drain naturally it must be tiled or sloped at '/e' to h/," per foot to a storm sewer or a "French Drain". If your PlayBooster is over 30' in length it is recommended to install more than one "French Drain" or similar system to allow drainage from the center of the play area and decrease the overall slope. If this is not possible, the structure may need to be "stepped" to take up the grade change. 3) Overhead Obstructions: Overhead obstructions within the use zones ofplayground equipment that are not part of the play structure (for example, tree limbs) shall be at least 84 in. (2130 mm) above each designated play surface or 84 in. (2130 mm) above the pivot point of swings. All overhead utility line clearances above the use zone areas shall comply with all local, state, and national codes, such as the National Electical Safety Code. 4) Locate all mainstructure post footing holes according to the dimensions shown on your PlayBooster plan. This can be accomplished by laying a deck on the &round and measuring from it; by laying out a base line string grid or using a builders transit. This step is very important and worth taking extra time to be precise. Location of component footings such as slide supports can be done at a later time. 5) Refer to the Typical Concrete Footing installation sheet. Dig holes to the proper width and depth as shown. (Only dig enough holes for one day's construction. Do not leave holes open over night.) Pour crushed rock in each hole level with each other and at least 4" deep as shown. This can be easily accomplished either with a builders transit or by laying out hole locations with a string grid, leveling the grid, and measuring down from the grid for each footing. Tamp the crushed rock down until compacted and at proper level. This step is impor- tant to ensure all posts will beat the proper height relative to each other, and it greatly simplifies installation. If the soils are loose or unstable, larger diameter boles may be necessary. Check with a local engineer if in doubt. 6) Start with the lowest deck and work your way to the highest deck following instructions on t tS installation sheets for typical post/deck assembly. Install barriers and roofs as located on the plan for stabil" 7) After the posts are at proper heights and plumb, and the decks are at proper height and I po jWe cd"te footings per the Typical Concrete Footing Detail. �>y --r C-) -< i ��---- 8) During construction, the site and all the material on it must be secured when unattendi469 prWent children from playing on them. Do not leave decks with unprotected openings when unattended teNorarri- cades if necessary. 9) Install all other play components per the installation instructions. After all componeAand enclosures are properly attached, pour the remaining concrete footings per the Typical Concrete Footing Detaif; 10) Install protective surfacing material. 11) Attach play hardware such as 'D' rings and swing seats last, after protective surfacing is in place and footings have cured at least 3 days. 12) Carefully and thoroughly inspect the entire PlayBooster to be sure all fastening hardware is tight. According to ASTM F1487, section 6.2 sharp, edgges and protrusions; any exposed bolt ends should not protrude beyond the face of the nut more than two (2) threads. This condition is not planned, but may exist in some applications because materials and finishes will vary. To remedy this situation, add a second nut or washer(s), extras have been added to the spare parts kit. See illustrations on reverse side of this sheet. Children should not be allowed on the structure until this inspection is complete. 13) Before children are allowed on the structure, the site must be cleaned and free of all construction debris and packaging material. Do not burn on the site. PlayBooster'e General Construction Guidelines Sheet 1 of 02001 by Landscape Stmclures All rights reserved Document #13412800 7 j & landscape structures Tools Required Tools required for installation are an auger, or other equiJpnmeet for diggin* 14" diameter footing holes; shovels, rubber mallet, drill (with'/,", 7/16', 9/16 11 16° and'/8" drill bits), tape measure, hex keys or alien wrenches, level, '/8" socket set, hammer, open end wrench set, screw driver, for surface mount a hammer drill, 1/." and '/," masonry bits and transit or string line to aid in layout. Some washable felt tip pens are also useful for marking clamp locations. Materials Required N All PlayBooster materials are supplied except concrete for footings, protective surface mate- rial, and curbing or edging matenal. With the exception of the special wrenchuir(for pinned hex fasteners) no other tools are supplied. D� C-) Recycling <M irl Many of our packaging materials can be recycled, please take the time to scV We aiff deli them to a recycler. Thank You. - C? 0 Installation Times Installation times, as noted on the back of the installation sheets, are approximate and will vary depending on soil conditions, installer's equipment and ability. Times indicated do not include unloading or unpacking equipment. The man hours given are for one person installing (unless otherwise noted). Cut time in half for two people. Technical Services If you have any questions or concerns about the installation of your structure, call our Technical Services Department at: 1-800-318-0035 (7:30 - 5:30p.m. CST/M-F). Illustrations For Note 10, (Reverse Side Of This Sheet) More Than Two (2) Threads Exposed Add Washers Add Another Nut (Align Flat Area) :••Installation 6U1 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 (763)912-3391 1-888-LSI-INSI (1-88MMA678) FAx(763)972-3185 landscape structures SAFETY NOTE Cnoosaa protective sunaorg matanal Ilial has a Cntioal Height Value of al least lha height of the Highest A¢euibla PaNFell H"ht ofthe adjacent eeupmenl. (Ref ASTM F14B1) 3.) Select a material that has a Critical Height value of at least the height of the highest accessible part. Accotdin& to the CPSC, Critical Height is defined as the maximum height from which the mun str ented metal headform, upon impact, yields both a peak decelera- tion of no more than 200 G's and a 141C value of no more than 1,000 when tested in accordance with the procedure described in the ASTM Test Method F1292. Request independent laboratory test results showing the critical height of each product per the above procedures for commercially available products. The CPSC has tested some common loose -fill materials that are commonly not tested as a protective surfacing. (See back page.) 4.) Cover the designated use zone with the desired materials. If a different type of material is used for the accessible route of travel, make sure the surfaces are maintained flush. Protective Surfaci for Your P Sheet 2 of 2 0 2001 by Landscape Stmctures All rights reserve Document #13412800 TOP OF GUARDRAIL OR HIGHEST N O PLATFORM WITH BARRIER PIVOT ZE2 ` POINT l� HEIGHT OF -4 n. G \ HIGHEST TAKEOFF I PART PLATFORM Em i SLIDES PLATFORM SWINGS CLIMBERSAND • Loose -fill - Sand, wood chips, etc. for non -accessible areas. CLIMBERS HORIZONTAL gra LADDERS 3.) Select a material that has a Critical Height value of at least the height of the highest accessible part. Accotdin& to the CPSC, Critical Height is defined as the maximum height from which the mun str ented metal headform, upon impact, yields both a peak decelera- tion of no more than 200 G's and a 141C value of no more than 1,000 when tested in accordance with the procedure described in the ASTM Test Method F1292. Request independent laboratory test results showing the critical height of each product per the above procedures for commercially available products. The CPSC has tested some common loose -fill materials that are commonly not tested as a protective surfacing. (See back page.) 4.) Cover the designated use zone with the desired materials. If a different type of material is used for the accessible route of travel, make sure the surfaces are maintained flush. Protective Surfaci for Your P Sheet 2 of 2 0 2001 by Landscape Stmctures All rights reserve Document #13412800 N O d � ZE2 ` l� 1.) Determine the highest accessible part - by definition. -4 n. G -- I �—.. 2.) Determine the type of surfacing material desired: Em i • Unitary - Bound rubber type materials for the accessible areas. • Loose -fill - Sand, wood chips, etc. for non -accessible areas. y gra 3.) Select a material that has a Critical Height value of at least the height of the highest accessible part. Accotdin& to the CPSC, Critical Height is defined as the maximum height from which the mun str ented metal headform, upon impact, yields both a peak decelera- tion of no more than 200 G's and a 141C value of no more than 1,000 when tested in accordance with the procedure described in the ASTM Test Method F1292. Request independent laboratory test results showing the critical height of each product per the above procedures for commercially available products. The CPSC has tested some common loose -fill materials that are commonly not tested as a protective surfacing. (See back page.) 4.) Cover the designated use zone with the desired materials. If a different type of material is used for the accessible route of travel, make sure the surfaces are maintained flush. Protective Surfaci for Your P Sheet 2 of 2 0 2001 by Landscape Stmctures All rights reserve Document #13412800 9& landscape structures® SAFETY NOTE Choose a Protective sin h, materiel that rias a Ch" Height V tdr 0 at bast the height W the Highest AttessiWs Part Fafl Height ItheaQacent equMwirs (Rel ASTM F1481) Critical Heights (in Feet) NA= Not Available * NOTE: Compressed depths most accurately depict conditions on a playground. * An approximation of the maximum fall height from which a life-threatening head injury would not be expected to occur, based on tests in which a headform yielded both a peak deceleration of less than 200 G's and a HIC of less than 1000 upon impact. *Handbook for Public Playground Safely,published by the U.S. Consumer Prod- ucts Safety Commission, Section 10, Table 2, page 21. N O Critical ® 2001 by LsiAscage StrucWres All ngMs reserver! Q jA Unc Depressed PDepth Compressed Material 6" 9" 12" 9" * Wood Mulch ................................................ T 10' III...............10' =fira m * Double Shredded Bark Mulch ...................... 6 10' 11' ................ 7' * Uniform Wood Chips ................................... 6 T 12 ................. 6' * Fine Sand ..................................................... 5' 5' 9'................ 5' * Coarse Sand ................................................. 5' 5' 6'................ 4' * Fine Gravel .................................................. 6 7' 10'................ 6' * Medium Gravel ............................................ 5' 5' 6'................ 5' NA= Not Available * NOTE: Compressed depths most accurately depict conditions on a playground. * An approximation of the maximum fall height from which a life-threatening head injury would not be expected to occur, based on tests in which a headform yielded both a peak deceleration of less than 200 G's and a HIC of less than 1000 upon impact. *Handbook for Public Playground Safely,published by the U.S. Consumer Prod- ucts Safety Commission, Section 10, Table 2, page 21. N O Critical ® 2001 by LsiAscage StrucWres All ngMs reserver! Q jA Mel C31 D_ 1 -4 _ C-) t Q1 �. iC-3 =fira m M � a Q D _ 0 j & landscape structures° crkrlrleo rM SAFETY NOTE Choose a IwMediva aur/ealg material abet nes a Critical Height Value of at least Vie height of the Highest Accessiole ParUFall HeightoltheaEjacenlequipment (Rel ASTM F14e]) 3-14.01 12026200 21"1530 Radius SPECIFICATIONS: Arch formed from 5" O.D. 6005-T5 alumi- num tubing with '/e' wall thickness. Unit is coated with a baked -on polyester powder - coating, color specified. Key: Deck Height Dimension 32"/810 .......92 '/,'/2350 40"/1020 ............ 98 1/2'72502 48"/1220 ............ 90 1/2'/2299 56"1420 ............. 98 1/2-72502 64"/1630 ............ 90 '/,'/2299 72"/1830 ............ 90 1/2-72299 At Grade (No DedQ... 97'/,'/2470 Arches 02001 by LaMscamS lures All rights reserved A -w -hl Ihmmncm✓L1411F replm, 0 n;177M(barged tubing r,, MWDocument#13433600 Typical Deck NOTE: Refer To Your Plan For Location Of Arches. v CD C 3 ID ...1 — 42" CC (7 C I M r r 1070 1 Loose Fill Protective Surfacing V Q Finished Grade _l;: ip ._ M1 y, -h •��a•�.-�'ltiL.. S. 4�'r4. `V 'slr.,'4 =C 'v k � V 'l�iV'�:a y Standard Concrete Footings Required w/ 34"/860 Bury 3 Arches 02001 by LaMscamS lures All rights reserved A -w -hl Ihmmncm✓L1411F replm, 0 n;177M(barged tubing r,, MWDocument#13433600 11-21-01 "How to distribute your hardware Headache Free" We have received feedback from you, our customers, that the most common delay in completing your playground installation is lost or misplaced hardware. Some of our most successful installations have used a "check- out" system with one person appointed to distribute the various hardware packages. Installation sheets are provided for each component that indicate hardware packages/items required to assemble that component. Refer to these sheets to determine which hardware items to request from the designated "check-out" person. HELPFUL HINTS: Read installation sheets. Be sure to use the correct length hardware as specified on the installation sheets. a `" T Be sure to use clamps in the correct locatiora'n4,catgtt— on the installation sheets.<m A M �. sc 7-1 Document#13701800 11-21-01 "How to distribute your hardware Headache Free" We have received feedback from you, our customers, that the most common delay in completing your playground installation is lost or misplaced hardware. Some of our most successful installations have used a "check- out" system with one person appointed to distribute the various hardware packages. Installation sheets are provided for each component that indicate hardware packages/items required to assemble that component. Refer to these sheets to determine which hardware items to request from the designated "check-out" person. HELPFUL HINTS: N O Read installation sheets. c) o —� Be sure to use the correct length hardware ag*ciiied En' the installation sheets. n s M j- Be sure to use clamps in the correct locations indicated on the installation sheets. "a Document#13701800 S & landscape structures Post Specifications: Post length shall vary depending upon the intended use and shall be a minimum of 42" above the deck height. All posts shall be powdercoated to specified color. All posts shall have a "finished grade marker" positioned on the post iden- tifying the 34" bury line (or 44" bury line for posts for 96" decks) required for correct installation and the top of the loose fill pro- tective surfacing. Top caps for posts shall be aluminum die cast from 369.1 alloy and powdercoated to match the post color. All caps shall be factory installed and secured in place with (3) self sealing rivets. A molded low density polyethylene cap, with drain holes, shall be pressed onto the bottom end of the post to in- crease the footing area. Steel Posts: All steel PlayBooster posts are manufactured from 5' O.D. tubing with a wall thickness of .120" and shall be galva- nized after rolling and shall have both the I.D.and the cut ends sprayed with a corrosion resistant coating. Aluminum Posts: All aluminum PlayBooster posts are manufac- tured from 6005-T5 extruded tubing conforming to ASTM B-221. Posts shall have a 5' outside diameter with a .125' wall thick- ness. Finished Sticker CONCRETE a, • 1.87 Cubic Feet per Footing. • 2000 PSI (Min.) 4 • 3000 PSI (Min.) If Freezing _ a Conditions Exist. Crushed Rock � 11 CERTIFIED SAFETY NOTE Choose a protective surtatlng material Nat has a Critical Heigh Value of el least Ne height Of the Highest A¢essible PaNFall IleigM gfNeagacenf equipment (Rel ASTM FU87) 13871600 Part Number Label Example 14" Minimum 360 PlavBooster'° Concrete Footinqs, 5" Posts Number Indicates Post Length *An Example: If you are using 12" of loose fill material, your concrete footing will be 22" deep. 02002by Landscape Sl ctures. Alinghtsreservd Em451014 Docwnen1%11871W rePLces R11g11700.R....M Pmt 1. ,Ih SnAk, Document#13871600 E C L O .9) � 0 2 n In - - u O �_ IIIII E _ _E_ =m d N coo a 14" Minimum 360 PlavBooster'° Concrete Footinqs, 5" Posts Number Indicates Post Length *An Example: If you are using 12" of loose fill material, your concrete footing will be 22" deep. 02002by Landscape Sl ctures. Alinghtsreservd Em451014 Docwnen1%11871W rePLces R11g11700.R....M Pmt 1. ,Ih SnAk, Document#13871600 9/& landscape Your playground may include equipment containing moving parts. Moving parts are more vulnerable to wear, mis-use and abuse than other non-moving parts. It is critical these parts be inspected and maintained according to our recommendations. As the owner, it is your responsibility to perform preventative maintenance and record your findings. Failure to do so may create a hazard and cause serious injury or death. 601 7TH STREET SOUTH, P.O. BOX 198 DELANO, MINNESOTA 55328-0198 (763) 972-3391 1.888 -LS I4NST (1-888-5744678) FAX (763) 972-3185 Document #14916800 N m Zyrn. E >a r � 601 7TH STREET SOUTH, P.O. BOX 198 DELANO, MINNESOTA 55328-0198 (763) 972-3391 1.888 -LS I4NST (1-888-5744678) FAX (763) 972-3185 Document #14916800 A& landscape structures- Waming Your playground may include equipment containing moving parts. Moving parts are more vulnerable to wear, mis-use and abuse than other non-moving parts. It is critical these parts be inspected and maintained according to our recommendations. As the owner, it is your responsibility to perform preventative maintenance and record your findings. Failure to do so may create a hazard and cause serious injury or death. 0 2004 by Landscape Suucwres All nghts reserved. Document 4 149 16800 N O (� OC i --;-4 jm i lel t � i1, tD F t� 0 2004 by Landscape Suucwres All nghts reserved. Document 4 149 16800 According to the U.S. Consumer Product Safety Commission (CPSC) nearly 70% of all playground injuries are caused by falls to the surface. PLEASE INSTALL AND MAINTAIN ADEQUATE PROTECTIVE SURFACING UNDER AND AROUND YOUR PLAYSTRUCTURE! Never let children play on the equipment before protective surfacing is installed. Consult the CPSC's Handbook for Public Playground Safety, the ASTM F1487 Standard or your Landscape Structures representative for more information. o landscape M structures' W r 7/12/2/6/5 2006 Document#15745100 According to the U.S. Consumer Product Safety Commission (CPSC) nearly 70% of all playground injuries are caused by falls to the surface. PLEASE INSTALL AND MAINTAIN ADEQUATE PROTECTIVE SURFACING UNDER AND AROUND YOUR PLAYSTRUCTURE! Never let children play on the equipment before protective surfacing is installed. Consult the CPSC's Handbook for Public Playground Safety, the ASTM F1487 Standard or your Landscape Structures representative—, for more information.Ck : -�- J landscape y structures' PS/PB/FP/Evos/Weevos 7/12/2/6/5 2006 Document #15745100 A& landscape structures® 1� Common Parts & Fasteners Button Head Cap Screws BHCS w/Pin Recommended Sizes Mat'] Torque Part# Inches mm or Grade Ft./lbs Kgm 137277-00 '/;'xY," (6,4x9,5) SSMAT 10 1.4 13184900 3/18"02'(7,9x12,7) (9,5x31,8) SST -WT 10 1.4 13232600 °/,83x3/e' (7,9x22,2) SST43V 10 1.4 192071-00 3/"3x1'/;' M8x24mm SSrflV 10 1.4 100195W '/"3X3/"' (9,505,9) SST -FAT 15 2 100195M '/e'x7/"' (9,5x22,2) SSMAT 15 2 10019800 3/ ", X1'/8' (9,5x28,6) SSrfAT 15 2 113027-00%" x 1 Y." (9,5x34,9) SSrfW 15 2 100171-00 3/"3x1'/;' (9,5x38,1) SSif14r 15 2 123224-00 3/"'x1"4" (9,5x42,9) SST -RU 15 2 10017300 %"x2" (9,5x50,8) SSrA4T 15 2 10019900 3/,"x21/," (9,5x57,2) SSMAT 15 2 10017400 3/"'x2'/2' (9,5x63,5) SSMAT 15 2 10017500 3/""x23/," (9,5x69,9) SSMAT 15 2 10017600 %11x3" (9,5x76,2) SSPAT 15 2 10016800 %"x33/;' (9,5x82,6) SSMAT 15 2 10020000 N."x31/2" (9,5x88,9) SSIA4T 15 2 124460M 31a"x33/;'(((9,5x95,2) SSr-FAT 15 2 100201-00 %,. x13/;' 15,9x38,1) SSTPM 5D 7 127551-00 %"x13/"' 15,9x38,1) SST- ED 7 ANT SIFZE 10020300 %"x23/;' (15,9x57,2) SSMAT ED 7 Hex Cap Screws Recommended Sizes Mat'l Torque Part # Inches mm or Grade Ft./lbs Kgm 10020800 3/"3x1" (9,5x25,4) SSMAT 15 2 100120600 %"X1 Y" ((9,5x38,1) SSMAT 15 2 100209W 3/"'x13/;' 9,5x44,4)SSMAT 15 2 135682-00 %..x33/"3 (9,5x79,3) SSMAT 15 2 135683W %"x4°/,"(9,5x117,5) SST 15 2 1002140D %"X6' (9,5x127) SSFRV 15 2 12149900 7/,"3x13/;' (11,1x114,3)SSfA4T 15 2 10021600 '/2'x11/4" (12,7x31,7) SST 15 2 131862-00 '/2'x21/4" (12,7x57,1) SSMAT 2) 28 Carriage Bolts Recommended Sizes Mat'l Torque Part # Inches mm or Grade Ft./lbs Kgm 10013500 3/," X13/;' (7,9x31,8) SSMAT 5 0.7 100147-00 % x13/;' (9,5x31,8) SSMAT 15 2 116017-00 3/8-'x13/2' 9,5x38,1) SSMAT 15 2 10014800 3/"3x1'/;' (9,5x44,5) SSMAT 15 2 Flat Head Cap Screws (FHCS) No Pin' With Pin NOTE: These are recommended torque applications per fastener size. When fasteners are used with plastic or wood products, the torque specifications will be excessive and we recommend that the installer apply some caution when tightening the fasteners. Plastic or wood products should begin to deform slightly. Fasteners indicated with -"Pat" includes a locking patch type material and should cure for 72 hours for maximum strength. Common Parts/Toraue C by Landscape Stmdums. All ngh( mserve Document Recommended Size Mat'l Torque Part # Inches nun or Grade F[./lbs Kgm 14868500 3/3''x3/;'9,5x19,05) &S$T 13 1.8 100252-W Y"3X1'!;' (9,5x 8) Miff 13 1.8 151421M 3/1" X1'/2' 3/"'x3'!2' (9,5x SEUswT —1 1 1.8 14876500 1/23x2'/4' 9,5x (12,5 S5WT SSi'Y fiS 1.8 130624-V 28 n O� fTt p' M 3 NOTE: These are recommended torque applications per fastener size. When fasteners are used with plastic or wood products, the torque specifications will be excessive and we recommend that the installer apply some caution when tightening the fasteners. Plastic or wood products should begin to deform slightly. Fasteners indicated with -"Pat" includes a locking patch type material and should cure for 72 hours for maximum strength. Common Parts/Toraue C by Landscape Stmdums. All ngh( mserve Document k& landscape structures BHCS w/Pin Limited Thread Bolts Expansion Anchors (used To Secure Components To Concrete Slabs) 11110;;0i Lag Screws Sizes Mat'] Part # Recommended Inches nun Sizes Mat'I Torque Part # Inches mm or Grade FtAbs Kgm 10029000 %1Ix7/6' (9,5x222) SSTfl1T 21 3 100292-00 1/;'x1'/;' Part # SSr�1T 21 3 15770400 7/,;'x2" ((9,5x31,8)) 11,11x51 SSMAT 4) 5,5 12706800 7/,8'x27/,6' (11,11)61,91) SOIAT 40 55 Lag Screws Screw, Type AB Thread BHCS w/Pin =' llllllllll>>. Sizes Mat'] Part # Part # Inches nun or Grade Head Type 100127-00 1/,6'x1'/4"(7,9x31,8) SST Hex Head 16819BM '/;'x11&" (9,5x38,13 SST Button Head (Shown) 139039-M '/;1x2" (9,5x50,8 SST Button Head (Shown) Screw, Type AB Thread BHCS w/Pin =' llllllllll>>. Try Recommended Sizes Mat'1 Torque Part# Inches mm or Grade FtAbs Kgm 10026300 1/;'x2'/;' (9,5x6g,9) AloySteel 15 2 10029600 1Z,'x2'/;' (12,7x69,9) Alloy Steel 2D 28 Drive Rivets ^7 Mat'1 Part # Size or Grade 129571-00 #14x'1" Ssr 127872-00 #14x'71" ssr 13SM-00 #14x1" SST 129672-00 #14x1'/4" SST Try Recommended Sizes Mat'1 Torque Part# Inches mm or Grade FtAbs Kgm 10026300 1/;'x2'/;' (9,5x6g,9) AloySteel 15 2 10029600 1Z,'x2'/;' (12,7x69,9) Alloy Steel 2D 28 Drive Rivets ^7 Low Crown Cap Nut Size Part # Inches Mat'I 100300 3/s"46UNC SST D p Sizes W Part # Inches mm Mat'1 10060900 /;'x'/,e' (6,4x4,8) AhimRi�et/A 1n 100611-00 '/;,X% AhanRNelYSSTPin 11330000 '4"x'/z' 6,4x12,7) AlumRi�/AlunPn 1006104M '/;'x%' 6,4x15,9) AJunRieSSTPn 139152-00 '/;'x'/;' ((((6,4x9,5) 6,4x19,05) Alun Ri%et/AJum Pn 10061300 '/;'x7/6' (8,4x22,2) AlumRieet/AlumPn 11815800 '/4"X1. (6,4x25,4) A urn Rir/A m Pin Low Crown Cap Nut Size Part # Inches Mat'I 100300 3/s"46UNC SST J V �l landscape structures Standard Hex Nuts O/ Sizes Mat'l Part # Inches or Grade 10032600 5/wl8UNC SST 100321-00 '/r16UNC SSMA 100377-00 '/5-16UNC SST 12829600 '/,-16UNC(JamNut) SST 10032600 11w14UNC SST 145021-00 7/w14UNC(JamNut) SST 100322-00 '/r13UNC SST 129892-00 '/r13UNC SSFPat 12989300 '/r13UNC(Jam Nut) SST 10032300 5/,-11 UNC Ssr Flange Nut w/Pin Sizes Mat'I Part # Inches or Grade 192054M M8x24mm SST 10035300 '/,16UNC SST Flat Washers I.D. O.D. 0.312 734 Q405 1.002 Q505 12M Q536 1.262 0.688 1.750 1.140 1.750 / 11 CEHTIFIElI Curved Spring Washer Sizes Mat'] Part# Inches Into or Grade I.D. O.D. 10038000 '/2" (12,7) SST 0531 0.795 SAE Flat Washers Sizes Mat'l Part # Inches nun or Grade 122009M '/4" 3)SST '/4' 35) 1001362-00 3/8' S SST 1127930D 7/b' 11,1)) SST 10006300 W, 12, SST 10038500 5jV" 15, SST 123737-00 11/11' SST I.D. O.D. 0.312 734 Q405 1.002 Q505 12M Q536 1.262 0.688 1.750 1.140 1.750 / 11 CEHTIFIElI Curved Spring Washer Sizes Mat'] Part# Inches Into or Grade I.D. O.D. 10038000 '/2" (12,7) SST 0531 0.795 SAE Flat Washers Fender Washers U Sizes Mail Part # Inches ton or Grade I.D. O.D. 10037800 5/e"xI%" (9,53x38,1) SSr 0405 1.5170 10037900 '/3'X7' (12,7x50,8) 0531 200.1 Tee Nut (PlayBooster Claink o I m ::3. M 4 Sizes r Mat'l Part # Inches or Grade 100351-00 3/,161]NC SST Sheet 2 of 3 Document#16338900 Sizes Mat'l Part# Inches MM or Grade I.D. O.D. 10035400 '/4' 35) SST 0281 0.625 10038500 '/e' SST 0,411 0.816 11356000 '/,' U, SST (1531 1.062 12950000 '/e' 15,9 SST 0.686 1.342 Fender Washers U Sizes Mail Part # Inches ton or Grade I.D. O.D. 10037800 5/e"xI%" (9,53x38,1) SSr 0405 1.5170 10037900 '/3'X7' (12,7x50,8) 0531 200.1 Tee Nut (PlayBooster Claink o I m ::3. M 4 Sizes r Mat'l Part # Inches or Grade 100351-00 3/,161]NC SST Sheet 2 of 3 Document#16338900 Set Screw Sizes Mat'1 Part # Inches mm or Grade 10029B00 3/01x1/,a' (9,501,1) Bolt Link 0 O Mat'I Part # or Grade 138915410 SST Double Clevis Part # Mat'1 or Grade SST Offset Hanger Clamp (PlayBooster) Part # Mat'1 11372900 CadAAniMm Half Clamp (PlayBooster) o C') C -Ti y � n t 0 t �' rn 0 ter- rn y o 10 Part # Mat'I CastAkrninu Deck Hanger Clamp (PlayBooster) o p Part # 138917-00 SST I108C221D Mat'1 kk landscape structures, Swing Hanger Clamp Part # Mat'1 12128M0 castM.r6arn Ring/Rail Hanger Clamp (PiayBooster) CastA uminum dhm ISO 14001 Offset Bolt Bracket (Piayshaper) J�1 Part # Hex -Pin Allen Wrench Mail Hex -Pin Driver Part # Description 101768500 Hex-PinAllenWench 100686430 Hex -Pin Drner(UsedVWAV,a'Socket) 6 -Lobe Wrench lYY 6 -Lobe Driver Part # Description 146017-006{.obeVJendi 146007-00 GLoheDnZerCM) Used With A6/,e'Sod(et) 12746300 Tans-PinDm2r(f-27)(Used VftA'/;'Socket) Sheet 3 of 3 Document #16338900 Uo#537M Document #16338W replaces#14361 U&tM Fu,en k1r1 landscape structures` INCH 1 Y." HOW TO DETERMINE BOLT LENGTHS Example shows a 1 Y." long plow bolt. Measurement method also applies to flathead cap screws. Example shows a 1 '/;' long BH cap screw. Measurement method also applies to hex cap screws, limited thread bolts, lag screws and carriage bolts. 2 4 Rule: Measurements should be based on the part of the screw that penetrates the surface. 5' 6 N O lz n o fi=t � ^� C � m r, -, v o v' o landscape structures° 1111� Iso 14001 Common Parts & Fasteners Button Head Cap Screws BHCS w/Pin Recommended Sizes Mat'I Torque Part# Inches mm or Grade Ftilbs Kgm 137277-00 Vi'x%" 6,4x9,51 SSTFff 10 1.4 13184900 '/�s'x'/:' ,9x12,7)) SSrflU 10 1.4 132525M 1/,,11x1/:' 9X22,2 18x24nm SST 10 1.4 192071-00 SSr43U 10 1.4 10019500 '/,11x6/s' 9,5x15,9) SSAW 15 2 10019500 31."X 7/s, 9,5x22,2 SSrfl1TT 15 2 10800 019 %"x1 Ye" 9.5x28,6 SSr43U 15 2 113027-00 '/,1"x16/,1' 9,5x34,9 9M 15 2 10D171-0(1 '/6'x1'/i' 9,5x38,1 SSr43U 15 2 123224-00 3,"x 1111," "!, " 9,5x42,9 SSMU 15 2 10017300 '/,11x2" 9,5x50,8 SST fl4T 15 2 100199M '/,'x21/4' 9,5x57,2 SSr43U 15 2 10D17400 '/,1x2'/i' 9,5x63,5 SSr43U 15 2 10017500 1/,'x2'/i' 9,5x66,9 SSrM 15 2 10017600 1/:'x3" 9,5x76,2 SSUAT 15 2 10016800 1/,'x31/," 9,5x82,6 SSrfl4T 15 2 100200M '/e"x31/7" 1/a"x3s/," 9,5x88,9) SSTAaT 15 15 2 2 12446300 9,5x95,2) SSTf}U 100201170 s/e"x11/" 15,9x38,1) SSr43U 5) 7 127551170 s/6"x1'�" 15,9x38,1) SST_ ED 7 MfRaEZE 10020300 6/,1'x2'/4' (15,9x57,2) SSrFAT 9) 7 Hex Cap Screws Recommended Sizes Mat'l Torque Part # Inches In or Grade FL/lbs Kgm 10020800 3/11x1" 9,5x25,4) SSr434T 15 2 10020800 1/:1x1'/" 9,5X38,1)))5 SSr43lT 15 2 t00d7917D '/e"x13 9,5x44,4 SSrE t5 2 135662170 '/s"x31/e" 9,5x79.3 SSr43U 15 2 135683M '/:'x41/e" ,5x117, ) SST 15 2 10021400 1/:' x 5' ,5x 127) SSW 15 2 00 121499 71,6"x11/4 11,1x114,3) SST-Fff 15 2 10021600 "x t'/;' 12,7x31,7) SST 15 2 131862-00 ', x2'1;' 12,7x57,1) SSrf14T 27 28 Carriage Bolts Recommended Sizes Mat'] Torque Part # Inches nun or Grade FtAbs Kgm 100135006/, "x1 Y." ,9x31,8) 15 Q7 1OD147-0D '/1x1'/;' ,5x31,8) SST -RU 15 2 116D17-00 '/:1x1'/:' (((9,5x38,1) SSr43V 15 2 10014800 1/:'x1'/;' 9,5x44,5) SSMV 15 2 Flat Head Cap Screws (FHCS) No Pin* With Pin BT�D 9EZD Recommended Sizes Mat'] Torque Part # Inches mm or Grade FtAbs Kgm 14868500 '/s"X'/4' (9,5X19,05) 100252-00` 1/a"X11/;' (9,5x$ 1 10 1/,1' X':/ 1 Y:' 1.8 14876548765 00 '/,1X3'/" '/,"x 9, 13082400' 2'74" 28 7 -C CT rn INOTE: These are recommended torque applications per fastener size. When fasteners are ush8 with plastic or wood products, the torque specifications will be excessive and we recommend that the installer apply some caution when tightening the fasteners. Plastic or wood products should begin to deform slightly. Fasteners indicated with -"Pat" includes a locking patch type material and should cure for 72 hours for maximum strength. Common P All nghi msen #16338900 13 1.8 I:FAT T 13 1.8 Q RMT 13 1.8 �ff-34T 13 19 cc96r 711) 28 CT rn a INOTE: These are recommended torque applications per fastener size. When fasteners are ush8 with plastic or wood products, the torque specifications will be excessive and we recommend that the installer apply some caution when tightening the fasteners. Plastic or wood products should begin to deform slightly. Fasteners indicated with -"Pat" includes a locking patch type material and should cure for 72 hours for maximum strength. Common P All nghi msen #16338900 BHCS w/Pin Limited Thread Bolts 111110111 Lag Screws IVlllllllll>>>`' / T I v, Sizes Mat'] Part # Recommended Inches nun Sizes Mat'] Torque Part # Inches mm or Grade Ftilbs Kgm 10229600 /e'x'/e' 9,5x22,2 SSMAT 21 3 100292-00 3/e'x1V;' 5x31,8)) SSifWT 21 3 157/04M '/,;'x2' 11,11x515 SST -RU 40 5S 1270MM '/,;'x2'/,;' 11,1ba61,91) SSPRU 47 55 Lag Screws IVlllllllll>>>`' / T I v, Screw, Type AB Thread BHCS w/Pin M 12 lllllllllh�` Sizes Mat'] Part # Part # Inches nun or Grade Head Type 1OD127-00 5/,;'x1'/;' ,9x31,8 SST Hex Head 16819800 '/;'xt'/z" 9,5x38,1 SST BultonHead (Shov-m) 13903900 3/;'x2" ,5x5Q8) SST Button Head(Stxwm) Screw, Type AB Thread BHCS w/Pin M 12 lllllllllh�` Expansion Anchors (used To secure Components To Concrete Slabs) Recommended Sizes Mat'] Torque Part # Inches mm or Grade Ftilbs Kgm 100253-M 3/4"x2'/;' 9,5x69,9) AbyS� 15 2 100295M '/z'x23/;' Mjx&),9) AiaySteel 23 28 Drive Rivets Mat'] Part # Size or Grade 129671-00 #14x'1,' ssr 127872-00 #14x'/4" ssr 136232-00 #14x1" Ssr 129672-00 #14x1'/4" ssr Expansion Anchors (used To secure Components To Concrete Slabs) Recommended Sizes Mat'] Torque Part # Inches mm or Grade Ftilbs Kgm 100253-M 3/4"x2'/;' 9,5x69,9) AbyS� 15 2 100295M '/z'x23/;' Mjx&),9) AiaySteel 23 28 Drive Rivets Low Crown Cap Nut Size Part # Inches Mat'] 100049M 3/;'-16UNC SST .N O_ �J � cD cb::: `-' �� _.- r Sizes _-tt"f T Part # Inches mm G *at'lr 100609M '/;'x'/,;' 6,4x4,8 Alu 'fUsnYn 100511-00 '/�"x'/;' 64x9,5 , 1SS7 n 11330000 '/,"x,4x12, A►pfpii 10061000 44"xN 6,4x15,9 AkmRKeVSS'Wh 1391M -OD '/4"x3/;' 6,4x19, rn AkRneftinPin 10051300 '/4"X'/e' 6.4x22,2) 2) Akin 11815800 '/;'x1" 6,4x25,4) AkmFbel/AkmPin Low Crown Cap Nut Size Part # Inches Mat'] 100049M 3/;'-16UNC SST VY✓ � landscape shuchmw Standard Hex Nuts Sizes Mat'l Part# Inches or Grade 100325M 5/„-18UNC SSr 1OD321-00 5/,-16UNC SST439 100327-00 5/,16UNC Ssr 12829600 '/r16UNC(JamNut) SST 100323M '/w14UNC Ssr 145021-00 7/„-14 UNC (Jam Nut) SST 100322-00 '/r13UNC SST 129692-00 'h-13UNC SSWat 12969300 V,13UNC(JamNut) SST 10032300 %-11 UNC SST Flange Nut w/Pin (DD Sizes Nat'l Part # Inches or Grade 19206400 M8x24mm SST 10035300 3/,-16 UNC SST Flat Washers 1.1 Part# Sizes Inches nun or Grade I.D. O.D. 12203900 '/4' (6,3� Ssr 0.312 734 100362-00 3/;' (9, Ssr 0.406 1.002 11279300 7/,;'(11,1 Ssr 0505 12B2 10000300 ,' (12 ssr 0536 12M 10036600 5/, 15, SSr O6B6 1.750 123737-00 1'/;' SSr 1.140 1.750 ��F C.rli�.d Curved Spring Washer Sizes mat'] Part # Inches mm or Grade I.D. O.D. 10038000 'I,' (12,7) SST 0.531 0.7% SAE Flat Washers Fender Washers V sins Marl Part# Inches mm or Grade I.D. O.D. 10037600 Sizes Mat'l '/,'xT (12,7x50,8) SST 0,531 2000 Tee Nut (PlayBoosterClamps) Part # Inches mm or Grade I.D. O.D. 100364-00 ' '/;' 35) SSr 0281 0.515 10036500 '/;' SSr 0.411 0.816 11355000 '/” 12 Ssr 0.531 1.062 12950000 15,9 SST 0.686 1.342 Fender Washers V sins Marl Part# Inches mm or Grade I.D. O.D. 10037600 5/;'x1'/,' (9,53x38,1) SST 0405 1.500 10037900 '/,'xT (12,7x50,8) SST 0,531 2000 Tee Nut (PlayBoosterClamps) 0 O C-) m s Sties E5 iLl Mail• s Part # Inches .r; x ea or G� IOM51-OD 3/,16UJC- cn SST C:) Sheet 2 of 3 Document#16338900 JI/b landscape structures, Set Screw OW Sizes Mat'1 Part # Inches nun or Grade 100298M 1/6"X7/,e" (9,5X11,1) SST Bolt Link I'm( # 138915M Double Clevis Part # Mat'l or Grade ssr Mat'1 or Grade Offset Hanger Clamp (PlayBooster) Part # Half Clamp (PlayBooster) Marl Deck Hanger Clamp (PiayBooster) Part # 138917-00 SST I108072-00 Mat'[ 0 N WWI I ow. Mfg go, - < r � o� a 0 Part # M 1 o n 105327-01 CaafNrnmrn Deck Hanger Clamp (PiayBooster) Part # 138917-00 SST I108072-00 Mat'[ k& landscape structures' Swing Hanger Clamp Part # Mat'l Ring/Rail Hanger Clamp (PlayBooster) Part # WalitlFIT1 11U'11 IIft ISO 14001 Offset Bolt Bracket (Playshaper) Part # 01, Mat'1 CasiAlurenun Hex -Pin Allen Wrench Hex -Pin Driver Part # Description 100685400 Hex-PrAllenVNendi 100686,70 Flex -Pin Dmrer(UsedWMAV,6'Socket) 6 -Lobe Wrench �. o ROM 6 -Lobe Driver Part # Description ��- 3� M �s Torx-Pin Driver 146017 -OD 6J..obeWterkch -05) 146007-00 6-LobeDriver A5)(UsedWOhAs/,;'Soc(et) 127463rD Tkxx-PinDnver(i-27)(Used MA'/;'Socket) Sheet 3 of 3 Document #16338900 Eco N537ND =c tf16338 )replaces055J36Wo. U&WFaten kio- landscape structures, 1 HOW TO DETERMINE BOLT LENGTHS Example shows a 1 '/," long plow bolt. Measurement method also applies to flathead cap screws. Example shows a 1 '/," long BH cap screw. Measurement method also applies to hex cap screws, limited thread bolts, lag screws and carriage bolts. INCH I' 2' 31 41 1 I 5I 1 1 6 mm 10 20 30 40 50 60 70 80 90 1 Rule: Measurements should be based on the part of the screw that penetrates the surface. N t� n �-1 OS Z-4 , 1 o C-) �n 1 C71 .� iTf 1 A O� 3 O W Did you know that most of the packaging materials you receive on a Landscape Structures order are recyclable? Do you reuse or recycle everything you can from your playground sites? We're making it easier for you to do the right thing and keep these materials out of landfills! FOAM/SCRIM SHEETS Landscape Structures has partnered with our supplier to recycle foam/scrim material, the grey and white sheets that are layered between the large painted parts. This material is not usually accepted at general recycling facilities but this supplier will re -use it in their manufacturing of new packaging materials. It's easy! Just put the foam/scrim from your installation site in a box and ship it to the facility closest to you. Here is a list of participating facilities throughout the U.S.: Foam/Scrim Products Only Pregis Plant Pregis Plant 159 N San Antonio Ave. 3825 N Main St. Pomona, CA 91767 Granite Falls, NC 28630 Pregis Plant Pregis Plant 8201 W Elowin Ct. 18 Peck Ave. Visalia, CA 93291 Glens Falls, NY 12801 Pregis Plant Pregis Plant 7574 Presidents Dr. 3500 S Highway 287 Orlando, FL 32809 Corsicana, TX 75109 Pregis Plant 1411 Pidco Dr. Plymouth, IN 46563 Pregis Plant Pregis Plant 310 Old Station Rd. Wenatchee, WA 98801 Foam/Scrim, Plastic Banding, Shrink Wrap Anchor Facility 480 Broadway St. St Paul, MN 55101 Anchor Facility 1501 Swasey Rd. Hudson, WI 54016 300 Harris Rd. LJ.' '. Wurtland, KY 41144 ;K LD Ln O Don't stop here! Most of the other packaging materials can also be recycled, reused or repurposed. • CORRUGATED CARDBOARD: Boxes can be broken down and recycled at a local recycler, or reused for other storage. • SHRINK WRAP: Contact your local plastic recycler and ask if they accept polyethylene plastic. • PLASTIC BANDING: Contact your local plastic recycler and ask if they accept polypropylene. If you have suggestions for recycling, reusing or repurposing other materials, please email them to: info@playlsi.com. Just one more way Landscape Structures is building healthy, sustainable communities. #16604400 182212 is an entanglement label Not an Install doc. N O CD nc_.-... 0 �ryy C r s cn 0 182213 is a hot surface label Not an Install doc,, N O_ e` Gn O �.1 cn 0 J11& landscape structures Look for compliance to the following guidelines and standards wheneveryou install playground equipment. It's your assurance that the products you install meet the most rigorous safety and quality assurance standards. Landscape Structures is a member in good standing of IPEMA, the International Play Equipment Manufacturers Association. IPEMA is a member - driven, international trade organization that represents and promotes an open market for manufacturers ofplay equipment. ((4IPEMA MEMBER �II In the interest of playground safety, IPEMA provides a Third Party Certification Service whereby a designated independent laboratory validates a participant's certification of conformance to ASTM F1487, Standard Consumer Safety Performance Specification for Playground Equipment for Public Use, except sections 7.1.1, 10 and 12.6.1; CAN/CSA Z614, Children'sPlayspaces and Equipment Standards, except clauses 9.8, 10 and 11; or both. The use of the corresponding logo in the Landscape Structures Inc. catalog signifies that Landscape Structures Inc. has received written validation from the independent laboratory that the product(s) associated with the use of the logo conforms with the requirements of the indicated standards. Check the IPEMA website (www.ipema.mg) to confirm product certification. The use zone and fall height requirements in this publication are shown to ASTM standards. The requirements for other standards may be different. According to the CSA, playground maintenance and inspection is a continuous and integral part of budgetary costs. The cost of inspection and maintenance shall be considered and incorporated into the budget at the time of design, purchase equipment and installation (11. LI Budgeting). The Consumer Product Safety Commission (CPSC) is a governmental organization that provides technical safety guidelines for designing, constructing, operating and maintaining public playgrounds. U.S. Consumer Product Safety Commission 4330 East West Hwy. Bethesda, MD 20814 www.cpsc.gov The American Society for Testing and Materials (ASTM) is a scientific and technical organization that is a major developer of standards for testing different types of materials. In 1993, the ASTM published "Standard Consumer Safety Performance Specifications for Playground Equipment for Public designation F1487-93. ASTM is more technical than the CPSC. ASTM revised its old standard and published a new standard in 1995, 1998, 2001, 2005, 2007 and again in 2011. American Society for Testing and Materials 100 Barr Harbor Dr. P.O. Box C700 V' I / West Conshohocken, PA 19428 www.astm.org The Canadian Standards Association Nearly all equipment developed by Landscape Structures is certified to meet CAN/CSA-Z614-07, the Children's Playspaces and Equipment Standard, through IPEMA. No The European Standard was d �pedthe -i European Committee for Standiid3ftc�tio The �! i majority of landscape Structures pr�" havq been designed to be TUV certified by a thirjy v3R'dator 1 to EN 1176: 2008, the European-41'rarl for Playground Equipment. ---`: Y L7pi') ISO 9001:2008 has a process -orientated structure, is International Play Equipment Manufacturers customer focused and emphasizes continuous Association improvement in quality. 4305 N. Sixth St. Suite A Harrisburg, PA 17110 www.ipema.org s,,., <,�,.ti - s'"•.�,�,,,• �'` c"111W �IPEMa �IPEMiC ISO 14001:2004 drives us toward operating in a P 8 CERTIFIED CERTIFIED manner that is environmentally conscious. ASiM ASTM F79a7 Ftala l�i_ 18014001 PS/PB/FP/Evos/Weevos Guidelines & Standards L 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 (763) 972-3391 1 -888 -LS I -INS T (1-888-574-4678) FAX (763) 972-3185 0 2012 by Landscape Structures. All rights reserved. Eco #54540 Document 18482200 replaces 15749200. Updated document Document#10482200 J U& landscape structures, Look for compliance to the following guidelines and standards whenever you install playground equipment. It's your assurance that the products you install meet the most rigorous safety and quality assurance standards. Landscape Structures is a member in good standing of IPEMA, the International Play Equipment Manufacturers Association. IPEMA is a member - driven, international trade organization that represents and promotes an open market for manufacturers of play equipment. [4,IPEMA MEMBER In the interest of playground safety, IPEMA provides a Third Party Certification Service whereby a designated independent laboratory validates a participant's certification of conformance to ASTM F1487, Standard Consumer Safety Performance Specification for Playground Equipment for Public Use, except sections 7.1.1, 10 and 12.6.1; CAN/CSA Z614, Children's Playspaces and Equipment Standards, except clauses 9.8, 10 and 11; or both. The use of the corresponding logo in the Landscape Structures Inc. catalog signifies that Landscape Structures Inc. has received written validation from the independent laboratory that the product(s) associated with the use of the logo conforms with the requirements of the indicated standards. Check the IPEMA website (www.ipema.org) to confine product certification. The use zone and fall height requirements in this publication are shown to ASTM standards. The requirements for other standards may be different. According to the CSA, playground maintenance and inspection is a continuous and integral part of budgetary costs. The cost of inspection and maintenance shall be considered and incorporated into the budget at the time of design, purchase equipment and installation (11.1.1 Budgeting). International Play Equipment Manufacturers Association The Consumer Product Safety Commission (CPSC) is a governmental organization that provides technical safety guidelines for designing, constructing, operating and maintaining public playgrounds. U.S. Consumer Product Safety Commission 4330 East West Hwy. Bethesda, MD 20814 www.cpsc.gov The American Society for Testing and Materials (ASTM) is a scientific and technical organization that is a major developer of standards for testing different types of materials. In 1993, the ASTM published "Standard Consumer Safety Performance Specifications for Playground Equipment for Public Use," designation F1487-93. ASTM is more technical than the CPSC. ASTM revised its old standard and published a new standard in 1995, 1998, 2001, 2005, 2007 and again in 2011. American Society for Testing and Materials 100 Barr Harbor Dr. *U1 P.O. Box C700 West Conshohocken, PA 19428 www.astm.org The Canadian Standards Association Nearly all equipment developed by Landscape Structures is certified to meet CAN/CSA-Z614-07, the Children's Playspaces and Equipment Standard, through IPEMA. The European Standard was developed by the European Committee for Standardization. The majority of Landscape Structures products have been designed to be TUV certified by a third -party validator to EN 1176: 2008, the European Standard for Playground Equipment. ISO 9001:2008 has a process-orienth'ted struGrwe, is customer focused and emphasra�non�uous improvement in quality. D --i 4305 N. Sixth St. Suite A Harrisburg, PA 17110 www.ipema.org ^w.;4- �,ov'••,°^.�� �-rt �.r un. ,.. ISO 14001:2004 drives us tow8r�l eras in IPEMA' IPEMA � �8 CERTIFIED CERTIFIED manner that is environmentally cu�crous ASTM ASTM P7497 F1Q94 WO M1 PS/PB/FP/Evos/Weevos Guidelines & Standards 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 (763) 972-3391 1-888-LSI-INST (1 -888-574-4678) FAX (763) 972-3185 0 2012 by Landscape Stmetums. All lights reserved. Eco #54540 Document 18482200 replaces 15749200. Updated document. Document#18482200 W, landscape structures, Typical Offset Hanger Clamp Assembly 5/8' x 2 14" BHCS w/Pin '/;'x2 BHCS G ISOM Typical Deck (32" Shown) ------------------------ --------- ___ _ I I I I I I _� - 40 7/1;' Rail SAFETY NOTE Choose a protective surtatlrg materiJhasaCticaleightt leaheight M the Highest Accessible PeHeightottheadacentNuipnent (Ret F4487) 10971300 H `o c d U C: 0 32" Deck. -Use' -.2 RaiRshown) 40" Deck - Used Rails Rail/Handloov Assemb 02013by Landscape Stwctures. AlinghtsresewW Document#19437600 A& landscape structures* J: 1BPEC8\194\1943760a%5 Parts List PlayBooster° Rail/Handloop Assembly Parti) Description Qty - 111275 -00 Handloop Assembly.................................................1 108542-00 Handloop, Specify Color ........................................... 1 100198-00 34" x 1 '/g" BHCS w/Pin, SST ................................... 4 100203-00 5/," x 2 V," BHCS w/Pin, SST ................................... 2 100351-00 3/g" Tee Nut, SST ........................................................ 4 100610-00 '/4" x 5/." Drive Rivet, SST ....................................... 2 105327-01 5" Half Clamp, Specify Color .................................. 2 113729-00 Offset Hanger Clamp, Specify Color ....................... 2 111276-00 Rail Assembly............................................................ 1 108569-00 Rail, Specify Color .................................................... 1 100198-00 3/." x 1 '/," BHCS w/Pin, SST ................................... 4 100203-00 5/8" x 2 1/4" BHCS w/Pin, SST ................................... 2 100351-00 3/8" Tee Nut, SST ........................................................ 4 100610-00 1/4" x 5/." Drive Rivet, SST ....................................... 2 105327-01 5" Half Clamp, Specify Color .................................. 2 113729-00 Offset Hanger Clamp, Specify Color ....................... 2 Specifications Handloop: Weldment comprised of 1.125' O.D. 11 GA (.120") steel tubing with 203 or 303 stainless steel inserts, with %" internal thread Finish: TenderTuN'"', color speci- fied. Raft: Weldment comprised of 1.125" O.D. 11 GA (.120") steel tubing with 203 or 303 stainless steel inserts, with 5/8" internal thread Finish: TenderTuff'"5, color speci- fied. Offset Hanger Clamp Assembly: Cast aluminum. Finish: PmShield®, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installatiou/specifications). Installation Time: Approx.1/4manhour Weight: 111275-00(One) 11 His. 111276-00 (One) 11 His. Installation Instructions I Mark locations of clamps on posts per dimensions on front of sheet. 2) Attach offset clamps to ends of rails/handloops using 1/8" x 2 1/4" BRCS w/pin. 3) Position rail/handloop on marked position on posts and attach using 5" half clamps and'/." x 1 '/." BRCS w/pin with'/a' tee nuts. Refer to the Typical Offset Hanger Clamp Assembly Sheet. 4) Install drive rivets in half clamps per the Typical Offset Hanger Clamp Assembly Sheet. 5) Install protective surfacing before users are allowed to play on the structure. Eco#54867 Doc wt#1943760Orep #14249300.Adde la blysp fire m. 0 O C-) cr+ < m T+ D Eco#54867 Doc wt#1943760Orep #14249300.Adde la blysp fire m. 9/& landscape structures® This 11,11n.0.1. rias peen designed ror cNore, 2 to 3 years old and uirm usmr '. ha.o soha;ea strength and <o«dl la Ad." penlslon regulwd. Part No. 156844-00-000 1 1 1 CERTIFIED SAFETY NOTE Choose a protective surfaang material that has a Cntical Height Value of at least the height of the Highest Accessible P.,Fall Height oftheadacentequignent (Ref. ASTM Ff481) Surfacing and pla surfaces Installation over O playsurfaces may become HOT and hold Ce a6Ch = rause horns. Check for hot N as w ouncmle611ffa, asphalt, - dp packed earth may surfaces prior to playing result in serious injury on the playground.of death hom falls. 2 '/;' 2'/;' 64 4 Part No. 182213.00.000 Part No. 115176-00-000 AWARNING Drawstrings have AWARNING entangled on slides This Playatmcmre and other playground �+wa�r.. p � a wre'.,nnaMaanLn orllY t user at a tone. has oxen designed a amnnm y5 e1a as N." l," or,hwlnq. fixcmld,en equipmentcausing = td, aqubmenis 6to 23 months old strangulation, REMOVE ..cona,andad for<nlmran and redalres... ra helmets, drawstrings, m rem as rare• wh�'n m� aro. V.." to. roha.e sumdent scarves and other suin. unnar.bod, atnnam and coominatlon. accessories around the nbeur%�nuxTmiadnaelna atragd... gduk aupervl,lon nur¢cmxlm monops pnmbpan. <dbre.mtion ronanad neck prior to playing on gduX p,MMabn '"Wild. the playground. ,amm smanaN,acamma Aad, a. .„a "" 264.. 24; Part No. 156846-00-000 Part No. 156848-00-000 Part No. 166751-00.000 Part No. 182212-00-000 Part No. 183064-00-000 This plfyser.dure has bal dami,md to, sh M, 2t 12 an Id and nedsi ds.% ton sufnciem pooh aM womlMipA aWMim ussv—dh„1.IM AA,n s,gnnlm sbwxM ncanena dao (W saWiad br pn..aaoL Olpy, user at a none. No moons m shevng. Tha. ep.lpn,ent is 0aso'. far cnldrm a to s yea., cad. fNn.m upo.41 y pM aY epwalnatgli,arl( /Wf avpra4lM aMY.L 21/," 64 TM1nW fi suucW,a b da+Yxd b dlosin rnrs WYaWn.ecdn'W.W lwu ben TI+redM"ucluawtleMad da eMd'm 2 to 5 fraprs old 21012 years old Y, dr 5 to 12 years old r N n„d,epv,aswe,fbMn aMkM sno 'Fc SWlcultl r."s,.M-6—t.ort xq,eµWps us„vblNre funbBN onnan andwo,dMia. avc,rJ.n nrdCm"a".. •auM avperviAon required AduX aupor l tori U.,ly rascnnns detl land,e0ubed lorpmuOaMnnl. r. Ad.a <upanl:.on y4an9lY recammentled. Part No. 200331.00.000 Part No.200332.00QDO Pg, No. 200333-00-000 Part No. 156850-00-000 Part No. 166815.00.000 "is Playstructure has been designed far dhlldra. 5 to 12 years old and nailer users to have sufficient strength and doomoauon. Ad,m o,.ralsion .t,.Wly redomn,..ded. This phYsnucture has Man designed for dMill 2 to 5 years old and repines user to lave sofll Yranpth and doordi.anad Adan wgrvWoa aaµrkad Part No. 156847-00-000 Part No. 156845-00-000 PB/PS/FP/Evos"I'Mi os® 7 O 1 NOTE: The Playstructure design wM-d6termlhe which P/ay/tSafestickerwillbesupplied. 1 INSTRUCTIONS: ;� Surface must be clean and dry prior to plying-9ticker"17eel back- ing sheet away from back of sticker a plac"icker in position. Using backing sheet, rub over face of sticker to -burnish down into place. Choose a location visible to adults in a conspicuous location on product. Stickers work best on painted parts. Where possible, avoid placing on rotationally -molded plastic parts, TenderTuff-coated parts or where children may step and wear off sticker. This applies to both Freestanding Play items and Composite Playstructures. Apply sticker adjacent to or visible from the primary entrance to the structure. Apply 4'-5' above the surface. Apply at least (1) one to every structure and (2) two to large Composite Playstructures. Warninq Labels 02014 by Landscape Strictures_ All nghle raserved. Ec.#(11WO82 oocundrt#20151300 n,plues #18306600.Added (3) —ing laMs. Document#20151300 landscape structures® Typical Mainstructure Post Play It Safe Label (3) Warning Labels Finished Grade Play It Safe 18263600 C)- 1 11' PB/PS/FP/EvosOMeevos® Warning Labels 02014 by LarMsc ,be Structures. All rights reserved 7 r afe Label SAFETY NOTE Choose a prolective sudedng mafenal Nat has a Cduwl Haight Value of at least Ne 4141 15014001drAM F landscape "'°' F,ae2, structures Thls phrftruct"re has been designed WARNING AWARNIN - for children 2 to 3 years oldo Installation over a end renew., „sera 8 Surfacing and playsudaces hard surface such m haw sunicient may became HOT and so as concrete, asphalt, nnngm and c..rdmdlon. cause bums. Check for hot or packed earth may N Ammr"perwssdf surfaces prior to playing result in serious injury 'en"'rel" on the playground. or death from falls. :Mona es uses to Mve sublcknt _21, IaM,egu,eefdprexl,6 pTyx jv elranl ended 9Y grength dtl ceodlnetbn. 261 1�' 2 Vz' 2 '/2" 4 4 84 h. c..ehonre m Part No. 115176-00-000 wdpN rdua,,.naea -^^w�^a d^f oen} Part No. 182213-00-000 NOTE: The Playstructure design w Oke ine Part No. 156844-00-000 ^"� which P/ayltSafestickerwillbesupYVDI • AWARNI ` (� Drawstrings have entangled on slides . Tw petzaamxe of The plarstrucmre and other playground MMMgdC mr <m orm only as -e. has been designed br:rind _ ria., nw:lae _ equipment causing Nr 2to l2 Years oltl h. d. hin gdshwug- 6 to 23 months old strangulation, REMOVE p p,�s,m.T nm. m.,Vm e,ero-sawaM > d,e,o to ha,° ii.c This en.ip nen 11 ,vended f., chadon e8lo and rewire:" helmets, drawstrings, s.t a1mglM1 entl c..rEmelmn t2 vean ole- ho had, sumdent scarves and other alar, wpe,v,slon semnenru omr cad Wren m and cd,minarion. g accessories around the S✓asi o.rrner+s rv,rem<'cT.,rn bwptr rK.mmeneM :nanpneri r ..,d,na,a .n.hee. Adult superNnon num.1,u M.YtT.npw waurvn neck Prbrbplayin9 on da ilea omreem,ee ad wesch.went_ al.n w rebmred. 1. the playground. niwn etreegN l.l. 2,/z, e. r.n _.. d!eader. , ,..... 64 Part No. 156846-00-000 Part No. 156848.00-000 Part No. 166751-00-000 Part No. 182212-00-000 Part No. 183064-00-000 Part No 156850-00.000 Part No. 166815-00-000 Z: •- -- 2 t/z, ...... - - 64 .. . Thu plry9lrucLnOe OesgmGfdcldlen Tnrs pldyfb,G'.uee0espatl ke ckv}an lice plryaYolOe°0epg,ed brcnreen are pbynrY[h,ro has bem odv f mer are lade. 2 to 5 years old 2 to 1i, years ofd ry S 12 years old lespnee rd child,en forren rs old r N d,dr Vuree nfanbwve rNX[M pnardo"n,i awlaowlncma an usa,ab Mee wllrm, 2104 Yean old NO WfM1Irpd6MVMp. a be,ygband rmdno.n—�gVHch dgw,nal T, 7an"'n oC,4ln mdcmdrotVf pluXwp.rvlson slronplY rde�,�l Gil AtluX eup.rvl6an Adult supsrWsl.n repuinQ :Mona es uses to Mve sublcknt Tnben pers,nls as ,skied fo, slid IaM,egu,eefdprexl,6 pTyx jv elranl ended 9Y grength dtl ceodlnetbn. <t. 5 1..' Old No.903-00-000 Part No.200331-00-000 Part No. 200332 -00f09 -i ParP033 a„e„e.,i—eie„n„sn,e,. s.lhcen,upne,.b.d, dp,haa m' c- t r_ —• — h. c..ehonre m __ ala wdpN rdua,,.naea -^^w�^a d^f oen} ° °""° "e "` NOTE: The Playstructure design w Oke ine W _ ^"� which P/ayltSafestickerwillbesupYVDI Part No 156850-00.000 Part No. 166815-00-000 Z: •- Part No. 156847-00-000 Part No. 156845-00-000 P B/PS/FP/Evos1Meevos® Labels 02014 by Landscape sbuctures All nghts reserved. Eve 40100082 Docum°e1620I5u00 rem. #18306((1). Added (3) raming fares. Document INSTRUCTIONS: 1* e -n Surface must be clean and dry prior to applyin�sticker. Peel back- ing sheet away from back of sticker and place sticker in position. Using backing sheet, rub over face of sticker to burnish down into This Maystrvcr"fe has been designed uct.re slgned 7hw,hio. place. Choose a location visible to adults in a conspicuous location rdcmld,on 5 to 12 years old forren rs old on product. Stickers work best on painted parts. Where possible, arra rebuires user` 'Karn avoid placing on rotationally plastic parts, TenderTufF-coated to haw sufncienl strength and coerainatipn. or6nMlon, parts or where children may step and wear off sticker. This applies Adult wpomblon ,hion to both Freestanding Play items and Composite Playstructures. etrd,sN racommdoncled. reclulreU. Apply sticker adjacent to or visible from the primary entrance to the —• — ebrilre, structure. Apply 4'-5' above the surface. Apply at least (1) one to every structure and (2) two to large Composite Playstructures. Part No. 156847-00-000 Part No. 156845-00-000 P B/PS/FP/Evos1Meevos® Labels 02014 by Landscape sbuctures All nghts reserved. Eve 40100082 Docum°e1620I5u00 rem. #18306((1). Added (3) raming fares. Document 414, landscape structures Typical Mainstructure Post Finished Grade P B/PST P/Evos®/Weevos® 0 2014 by Landscape Structures. All rights reserved It Safe Label (3) Warning Labels Warni Play It Safe Labels s 0 0 CD 182830 o r rn afe Label R/l/t landscape structures® PLAN/FOOTING LAYOUT NOTE: Attach belt to mounting angles with textured side up. (2) Mo Plates I 1 1 1 CEATIFIEO (8)Typical Offset Hang Clamp Assemblies DETAIL BELT TO DECK ATTACHMENT (10)3/," Low Crown Cap Nuts w/Patch & 3/;' Flat Washers Mounting Angles (2) (8)3/1 x 1'/;' BHCS w/Pin w/ %" SAE Flat Washers (8) 3/1 Low Crown Cap Nuts w/Patch & 3/1 Flat Washers 114373 Belt rights reser d SAFETY NOTE Choose a protective surfaarg material that has a Critical Height Value of at least the height of the Highest Accessible PaNFall H"Nof IheaQacent egWpmeht. (Ref ASTM Ff481.) 20509000 DETAIL BARRIER ATTACHMENT Belt 42" (8) a/;' Flange Nuts w/Pin Deck x2 (2)Barriers i� NOTE: Attach belt to mounting angles with textured side up. #20509000 U k landscape structures" Parts List Part# Description Qty. 166446-00 Mounting Plate, Specify Color ................................. 2 130353-00 Mounting Angle, Specify Color ............................... 2 113431-00 Barrier, Specify Color ............................................... 2 156880-00 Belt.............................................................................. 1 105327-01 5" Half Clamp, Specify Color .................................. 8 113729-00 Offset Hanger Clamp, Specify Color ....................... 8 205098-00 Belt Bridge Attachment Hardware Package 100198-00 %" x I '/e" BHCS w/Pin, SST .................................. 8 203378-00 3/a" Low Crown Cap Nut w/Patch, SST .................. 18 100362-00 3/." Flat Washer, SST ................................................ 18 100365-00 3/e" SAE Flat Washer, SST ........................................ 8 131571-00 Barrier Attachment Hardware Package ............. 1 100173-00 3/e x 2" BRCS, SST .................................................. 8 100198-00 3/e' x I '/t" BHCS w/Pin, SST... ..... ___ ................ 16 100351-00 3Q' Tee Nut, SST ........................... ......................... 16 100353-00 3/." Flange Nut w/Pin, SST ....................................... 8 100610-00 '/a" x 3/e" Drive Rivet, AL/SST................................. 8 Specifications Belt: Made from .315" thick mini rough top 3 -ply rubber belting with polyester fabric plys, 36'/," wide x 41 long, black in color. Mounting Angle: Weldmentcolnprised of2'/;'widex2'/"highx361/r" long formed 10 GA (.135") carbon steel with %" x I'/$" stainless steel studs. Finish: TenderTufTa, color speci- fied. Mounting Plate: Fabricated from 2" wide x 36 '/r" long '46" HR flat steel. Finish: ProShield'", color specified. Permalener Panel: Solid color panel measures 35 %" wide x 40 %" high, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproofin design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 1 '/r man hours Weight: 14816s. PlayBooster41114373 Belt Bridge, 4233 Installation Instructions 1) With posts/ decks in position, attach mounting angles to face of decks. Refer to the Belt To Deck Attachment Detail. 2) Attach belt to mounting angles. Refer to the Belt To Deck Attach- ment Detail. 3) Mark posts for the appropriate location for the (8) offset hanger clamp assemblies. 4) Fasten offset hanger clamp assemblies to marked position on posts. Refer to the Typical Offset Hanger Clamp Spec Sheet. 5) Attach barriers to offset hanger clamps using'/." x 2" BHCS and'/." flange nuts w/pin. See Barrier Attachment Detail. 6) Install'/,' x 3/." drive rivets in all 5" half clamps Refer to the Typical Offset Hanger Clamp Spec Sheet. 7) Install protective surfacing before users are allowed to play on the structure. rwMIm199 n" arme3t 00509000 repixu#18989300. Raps Belt Bridee AtmeW , Hardware Package. N O teC.) Cfr n �' z< M 7� U D O aD rwMIm199 n" arme3t 00509000 repixu#18989300. Raps Belt Bridee AtmeW , Hardware Package. SAFETY NOTE Choose a protective suRatlrg material that /� hes a Critical Height Value of at least the dhM IS014001 , He ghta he adecenteq Pe't"n`I(Re SFM landscape � Certified F DETAIL 19045300 structures° Wiggle DIRECT BURY Ladder ^y�: Loose Fill (2) Handhold BHCS w/Pin ; ' -.�• "'s';,." - o Protective �. ova Typical Panels t"// 3/e" Standard Surfacing PlayBooster Hex Nuts Post Top of Panel Subgrade 15"MaX Support - 0 n Top of Concrete trema DETAIL PANELATTACHMENT 12" 80 (2) 3/a' Post 300 o " Flange (2) Typical m Nuts Offset Hanger M w/Pin Clamp Assemblies (2),/8 e x 3 a/4, (2)Spacer BHCS w/Pin Tubes TOP 3/a' x 1 BHCS (2) 3/;' Flange Nuts w/Pin (2) 3/811 x 7/a BHCS w/Pin w/ 3/a' SAE Flat Washers DETAIL ATTACHMENT Rail Wiggle Ladder (2) Her Panels (2)3/." Stand Hex Nuts w/ SAE Flat W KEY Height Dimension "A" Off 32" / 810 Deck ................................................. 28" / 710 Off 40" 11020 Deck ............................................... 30" /760 Off 48" / 1220 Deck ............................................... 31" / 790 Off 56" / 1490 Deck ............................................... 31" / 790 Off 64" / 1630 Deck ............................................... 34" / 860 Off 72" / 1830 Deck ............................................... 39" / 990 Protective Surfacing DETAIL DECK MOUNT 2'/;'x2" Deck BHCS w/Pin wit 3/a' SAE Flat "e Washers (2) Handhold Panels PLAN VIEW/FOOTING LAYOUT 63/41 171 O NOTE: Dimensions shown in KEY are based on 12" of rotective surfacing and top of supports 2" below ubgrade. Dimensions will vary if your depth of pro- tective surfacing varies. Read installation instructions. PlayBooster° i Wiggle • • 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 7631972-3391 1-888.LSI-INST 1 -888 - Document landscape structures, J:ZPECS\190\19045300. P65 Parts List PlayBooster° 123284 Wiggle Ladder, 32"-72" Decks, DB Part# Description Qty. 139563-00 Handhold Panel, Specify Color ................................ 2 105327-01 5" Half Clamp, Specify Color .................................. 2 113729-00 Offset Hanger Clamp, Specify Color ....................... 2 113468-00 Spacer Tube, Specify Color ...................................... 2 118029-00 Support (DB).............................................................. 2 152159-00 (32" Deck) 54'/,6" Chain, Specify Color ............... 2 119813-00 (32" Deck) Rail, Specify Color ................................ 2 190455-00 (32" Deck) Wiggle Ladder Hardware Package. 1 124460-00 3/e" x 3 34" BHCS w/Pin, SST .................................. 2 100196-00 %" x %11 BHCS w/Pin, SST ..................................... 4 100198-00 3/e" x 1 '/a' BHCS w/Pin, SST.,...... .......................... 8 100327-00 3/e" Standard Hex Nut, SST ...................................... 4 100351-00 3/e" Tee Nut, SST ........................................................ 4 100353-00 3/e' Flange Nut w/Pin, SST ....................................... 4 100365-00 3/s" SAE Flat Washer, SST ........................................ 6 100173-00 3/e" x 2" BHCS w/Pin, SST ....................................... 2 152055-00 (40" Deck) 59 151," Chain, Specify Color .............. 2 119813-00 (40" Deck) Rail, Specify Color ................................ 3 190456-00 (40" Deck) Wiggle Ladder Hardware Package. 1 124460-00 3/s" x 3 3/i' BHCS w/Pin, SST .................................. 2 100196-00 3/8" x 7/i' BHCS w/Pin, SST ..................................... 4 100198-00 3/s" x I '/s" BHCS w/Pin, SST ................................. 10 100327-00 3/e" Standard Hex Nut, SST ...................................... 4 100351-00 3/s" Tee Nut, SST ........................................................ 4 100353-00 3/s" Flange Nut w/Pin, SST ....................................... 4 100365-00 3/e" SAE Flat Washer, SST ........................................ 6 100173-00 3/e' x 2" BHCS w/Pin, SST ....................................... 2 152056-00 (48" Deck) 68 '/p Chain, Specify Color ................. 2 152057-00 (56" Deck) 76 3/,' Chain, Specify Color ................. 2 119813-00 (48" & 56" Deck) Rail, Specify Color .................... 4 190457-00 (48"&56"Deck)Wiggle Ladder Hardware Pkg.. 1 124460-00 3/s" x 3 3/4' BHCS w/Pin, SST .................................. 2 100196-00 3/s" x'/s" BHCS w/Pin, SST ..................................... 4 100198-00 3/s" x 1 '/s" BHCS w/Pin, SST ................................. 12 100327-00 3/e" Standard Hex Nut, SST ...................................... 4 100351-00 3/s" Tee Nut, SST ........................................................ 4 100353-00 3/s" Flange Nut w/Pin, SST ....................................... 4 100365-00 3/a' SAE Flat Washer, SST ........................................ 6 100173-00 3/e" x 2" BHCS w/Pin, SST ....................................... 2 152157-00 (64" Deck) 84 Chain, Specify Color ............... 2 119813-00 (64" Deck) Rail, Specify Color ................................ 5 190458-00 (64" Deck) Wiggle Ladder Hardware Package. 1 124460-00 3/s" x 3 3/4" BHCS w/Pin, SST .................................. 2 100196-00 3/8" x 7/s" BHCS w/Pin, SST ..................................... 4 100198-00 3/s" x 1 '/e" BHCS w/Pin, SST ................................. 14 100327-00 3/s" Standard Hex Nut, SST ...................................... 4 100351-00 s/a' Tee Nut, SST ........................................................ 4 100353-00 3/a' Flange Nut w/Pin, SST ....................................... 4 100365-00 %" SAE Flat Washer, SST ........................................ 6 100173-00 3/81' x 2" BHCS w/Pin, SST ....................................... 2 152158-00 (72" Deck) 92 7/s" Chain, Specify Color ................. 2 119813-00 (72" Deck) Rail, Specify Color ................................ 6 190454-00 (72" Deck) Wiggle Ladder Hardware Package. 1 124460-00 3/8" x 3 3/4" BHCS w/Pin, SST .................................. 2 100196-00 3/e" x 7/s" BHCS w/Pin, SST ..................................... 4 100198-00 3/s" x 1 '/s" BHCS w/Pin, SST ................................. 16 100327-00 3/s" Standard Hex Nut, SST ...................................... 4 100351-00 3/e" Tee Nut, SST ........................................................ 4 100353-00 3/s' Flange Nut w/Pin, SST ....................................... 4 100365-00 3/,' SAE Flat Washer, SST .............................._ ....... 6 100173-00 %" x 2" BHCS w/Pin, SST .......................... ............ 2 DB = Direct Burr SDecifications Chain: 4/0 Chain zinc plated. Finish: TenderTufl ,colorspeci- Concrete Req.: fled. Rail: Fabricated from "/tb' diameter x 27 "/,s' long CRS solid but stock with both ends tapped'/s". Finish: TenderTuff, color specified. Support: Fabricated from 1.315" O.D. RS -20 (.080" - .09011) galvanized steel tubing. Handhold Panel: Solid color Permalenea, color specified. Spacer7Lbe: Made from 6061-T6 aluminum'/s" O.D. x 1 Finish: ProShielda, color specified. Offset Hanger ClampAssembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) MASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 2'/r man hours Concrete Req.: Approx. 2.6 cu. fl. Weight. Off 32" Deck - 41 lbs. Off 40" Deck - 47 lbs. Off 48" Deck - 52 lbs. Off 56" Deck - 53 lbs. Off 64" Deck - 58 lbs. Off 72" Deck - 64 lbs. Fall Height: Deck Height Installation Instructions 1) Attach chains and outside holes of handhold panels to the face of deck using 3/s" x 2" BHCS w/pin with 3/s" SAE flat washers and 3/s" stan- dard hex nuts with 3/s" SAE flat washers. Attach inside holes of handhold panels to the face of deck using 3/s" x'/s" BHCS w/pin with 3/a' SAE flat washers and 3/s" flange nuts w/pin. Refer to the Deck Mount Detail. 2) Attach offset hanger clamps to posts at heights shown using 5" half clamps, 3/s" x 1 '/s" BHCS w/pin and 3/q" tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet t9 3) Attach handhold panels to the offset hl&r clams-asemblies using 3/g' x 3 3/j' BHCS w/pin, spacer mbetLVAC3/s" 11ge nuts pin. Refer to Panel Attachment Detail. :L>:::; —4 4) Attach wiggle ladder rails between chawK Ing &1lx 1 'q" 51 CS w/pin. Refer to the Rail Attachment NOTE: Fire M at- taches 13'/r"or (10) links down from tit t th�tain, �tac the remaining rails 11 " between rails, as s1 O `✓ 5) Determine footing locations by pulling5ains tig&nd laying end on subgmde. Dig footing holes where chains megp0ubgrade to the width and depth shown. 6) Fasten chains to the supports using 3/g' x 7/e' BHCS w/pin and 3/s" standard hex nuts. 7) Pour concrete into footing holes. Push supports into concrete until chain is tight and top of support is positioned 1 3/4" above subgrade. Temporarily brace supports into position until concrete has cured. Refer to the Direct Bury Detail. 8) Atter concrete has cured a minimum of 72 hours, remove support brace and install protective surfacing before users are allowed to play on the structure. &og54767 Docwnrnl 819015300 rtpleca NI6000900. Re01aced lurdw"re Pazke6es. A& landscape structures® PLAN VIEW/ FOOTING LAYOUT 40" - 48° Deck 12114 17 'l Typical 42" Concrete Typical Play Booster Post of Pane1y (4)'/,'Flange (4) a/e' X'/e � � Nuts w/Pin BHCS w/Pin w/ a/;' SAE Flat Washers , , , , , , I , , I , I , I , , I , 'I Protective I�- Surfacing Footing (2) Handhold Panels\ ;' x 1 a/f 40"-48" Deck Loop 'IayBoostee 128252 2W2 by Landsc ,ba Structures. All rights reserved. SAFETY NOTE choose a protective surtadng maWrAllm terial that has a critical Height Value of elheight oleast iha all IS014001 HegMN'heatl'aer,teq i0 ss °Ithe Hghest IRef A > Cerll'letl F1481) 13989000 (2)TypicalOffset DETAIL Hanger Clamp PANEL ATTACHMENT Assemblies , (2)3 /," Flange\ Panel Nuts w/Pin ! \ T2 ur 2) %" x 3'/." AIL BHCS w/Pin SURFACE MOUNT a/,' Standard Hex Loop Nut w/ /;'Flat� Ladder Washer 34" X 2 34 Expansion Anchor u „ Concrete " ` Crushed NOTE: Sufficient protec- Rock tive surfacing must cover hardware to satisfy fall height requirements. DETAIL DIREC"URY © Loop Ladder Loosev?L1!!!+ 4 :. Subgrade - 05 NConcrete r: !. Bottom Of Ladder '"^ - - When Attaching To N a v A 48" Deck Crushed Rock 12" Ladder, 40"-48" 300 . 1 Document#13989000 PlayBooster" 128252 Loop Ladder, 40ee-48ee landscape structures* Parts List Part# Description Qty. 113558 Loop Ladder (40" & 48") DB, Specify Color......... 1 112913 Loop Ladder 40" SM, Specify Color ....................... 1 113567 Loop Ladder 48" SM, Specify Color ....................... 1 139563 Handhold Panel, Specify Color ................................ 2 105327 5" Half Clamp, Specify Color .................................. 2 113729 Offset Hanger Clamp, Specify Color ....................... 2 113468 Spacer Tube, Specify Color ...................................... 2 100610 1/4' x ,/g" Drive Rivet AL/SST.................................. 2 139892 Loop Ladder (Tenderdeck) Hardware Package 1 100196 N" x Y." BHCS w/Pin, SST ..................................... 4 100198 %" x I I/," BHCS w/Pin, SST .................................. 4 100351 3/c" Tee Nut. SST ........................................................ 4 100353 '/," Flange Nut w/Pin, SST ....................................... 6 100365 '/," SAE Flat Washer, SST ........................................ 4 113027 3/e" x 1 3/e" BHCS w/Pia, SST .................................. 2 124460 3/c" x 3 %" BHCS w/Pin, SST.... .............................. 2 121256 2 -Hole (SM) Hardware Package ........................... 1 100263 1/e" x 2 1/e" Expansion Anchor .................................. 2 100327 3/e" Standard Hex Nut, SST ...................................... 2 100365 3/e" SAE Flat Washer, SST ........................................ 2 DB — Direct Bury SM = Surface Mount Specifications Loop Ladder: Weldment comprised of 1.125" O.D. 11 GA (.120") black steel tubing. Finish: TenderTufls, color speci- fied. Handhold Panel: Solid color Pennalenee with 3/a" x 14," handholds, color specified. Spacer7Lbe: Made from 6061-T6 aluminum %" O.D. x 1 13/36". Finish: ProShield'v, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- actinstallation/specifications). Installation Time: SM - Approx. 1 1/1 man hours DB - Approx. 2 man hours Concrete Req.: 26" - Approx. 2.6 cu. B. Weight: 64 lbs. Fall Height: Deck Height Installation Instructions 1) (Direct Bury) Dig footing holes spaced as shown. 2) Attach the handhold panels to the face of the deck using 3/t" x 7/e" BHCS w/pin with %" SAE flat washers and 3/," flange nuts w/pin. 3) Attach offset hanger clamps to posts at height shown using 5" half clamps, 1/e' x 1 4a' BHCS w/pin and 1/r" tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 4) Attach handhold panels to the offset hanger clamp assemblies using '/s" x 3 3/4" BHCS w/pin, spacer tubes and'/," flange nuts w/pin. Refer to the Panel Attachment Detail. 5) Using a 7/„” drill bit, drill out the upper 1/g" pilot hole in each handhold panel for attachment of loop ladder. 6) Attach loop ladder to handhold panels using'/." x 1 3/a' BHCS w/pin 7) (Direct Bury) With loop ladder plumb, pour concrete footings. Al- low concrete footings to cure for a minimum of 72 hours before us- ers are allowed to play on the structure. (Surface Mount) With loop ladder plumb, drill 1/." x 3" deep holes through mounting plates using hammer drill and'/," masonry bit. Tap expansion anchors into drilled holes. Fasten mounting plates to expansion anchors using 1/," standard hex nuts with'/," SAE flat washers. 8) Install protective surfacing before users are allowed to play on the structure. Eco#51368 Document #13989W0 Ml #13585100. Added We b hu Id [. 0 cn C')-� --4r CT, r M iG 3 CO O 03 Eco#51368 Document #13989W0 Ml #13585100. Added We b hu Id [. Typical PlayBooster (2) Handhold (2) Spacer Post Panels F----ITubes I I I I I I I I I d o BHCS w/Pin Ol Top n 15" Max'-- I I en I I � I I I I I I I I I I I I Loop Center 40" �Deck I I I I I I I I lfll� BHCS w/Pin (4)'/e" Flange w/%" SAE Flat Nuts w/Pin Washers (Small) I I I I I I II 'I I I I I I I I I I I I I I I Protective Rail IN. DETAIL ,See Frame DECK ATTACHMENT Assembly %------ Detail Deck _- ard dhM — SAFETY E Choose a protective Y NOTE material Nat NOTHeight has a Critical Height Value of at least the height of the Highest Accessible Part/FallISO N A 14001 . of the adjacent equipment (Refkk r413HM3M CuutiJ ASTM F1487.)landscape structures° is°°76°° Grips DETAIL (2) Typical Offset Hanger Clamp HANDHOL DPANEL Assemblies ATTACHMENT (2)3 /." Flange \ Nuts w/Pin Post SII \ / (2)Handhold X Panels Typical PlayBooster (2) Handhold (2) Spacer Post Panels F----ITubes I I I I I I I I I d o BHCS w/Pin Ol Top n 15" Max'-- I I en I I � I I I I I I I I I I I I Loop Center 40" �Deck I I I I I I I I lfll� BHCS w/Pin (4)'/e" Flange w/%" SAE Flat Nuts w/Pin Washers (Small) I I I I I I II 'I I I I I I I I I I I I I I I Protective Rail IN. DETAIL ,See Frame DECK ATTACHMENT Assembly %------ Detail Deck _- ard (2)a/e,x1,/a, BHCS w/Pin w/ a/a' SAE Flat Washers (Small) a/;' Flange w/Pin Mounting &ip Nuti w7'/a" SAE Flat�tWasher9 (ail) Surfacing ^.` a 7 C3NOTE: Ali nzboth bolts (24) /, x /a (27)a/e" x 1 V;prior to hand tightening BHCS w/Pin BHCS w/Pin Dcn to 15 ft. lbs. w/ /a Flat pWashers (Large) PlayBoosterO 143199 Conical ClimberTM, aota Sheet1of2 all- ® 21 7 by Lanbscape Structures. All rights reserved Document #160078°° a/;'mall) \.Hex Belt FrHand Grips (2)a/e,x1,/a, BHCS w/Pin w/ a/a' SAE Flat Washers (Small) a/;' Flange w/Pin Mounting &ip Nuti w7'/a" SAE Flat�tWasher9 (ail) Surfacing ^.` a 7 C3NOTE: Ali nzboth bolts (24) /, x /a (27)a/e" x 1 V;prior to hand tightening BHCS w/Pin BHCS w/Pin Dcn to 15 ft. lbs. w/ /a Flat pWashers (Large) PlayBoosterO 143199 Conical ClimberTM, aota Sheet1of2 all- ® 21 7 by Lanbscape Structures. All rights reserved Document #160078°° k14 landscape structures, Parts List PlayBooster'p' 143199 Conical Climber'", 40" Part# Description Qty. 151224 Belt ....... ..................................................1 Approx. 2.6 cu. ft. 160052 Rail, Specify Color........................................................2 151244 Center Loop, Specify Color...........................................1 Deck Height 143087 Footer, (DB), Specify Color..........................................2 143166 Footer, (SM), Specify Color ..2 143604 Handhold Panel, Specify Color.....................................2 142878 Mounting Plate, Green .................................................. 12 113468 Spacer Tube, Specify Color...........................................2 105327 5" Half Clamp, Specify Color .........2 113729 Offset Hanger Clamp, Specify Color ............................2 100610 3/4" x 5/." Drive Rivet, AUSST......................................2 143492 Hand Grip Set............................................................1 143110 Hand Grip, Blue............................................................3 143110 Hand Grip, Yellow..... ........................... .......... ............. 3 143110 Hand Grip, Red..............................................................3 143110 Hand Grip, Green..........................................................3 151356 Conical Climber, Hardware Package ......................1 100196 '/a" x'/." BHCS w/Pin, BST.........._.............._......._....28 100198 3/e" x 1 '/." BHCS w/Pin, SST ............... 35 100327 %" Standard Hex Nut, SST...........................................2 100349 3h" Low Crown Cap Nut, SST. ........... 27 100351 Y." Tee Not, SST... ..... _ ................................................. 4 100353 '/," Flange Nut w/Pin, SST___..___ ......................... 32 100362 '/." Flat Washer (Large), SST.. ................................ __27 100365 3/8" SAE Flat Washer (Small), SST ............................... 35 124460 3/." x 3'/4" BHCS w/Pin, SST.......................................2 100609 1/4" z 3/,6" Drive Rivet, AUAL..............._......................2 121348 4 -Hole (SM) Hardware Package ......_ ......................1 100266 '/," x 2'/4" Expansion Anchor.......................................4 100322 '/2" Standard Hex Nut, SST...........................................4 100363 '/,' Flat Washer. SST.....................................................4 DB = Direct Bury SM - Surface Mount SDecifications Center Loop: Weldment comprised of 1.315" O.D. RS -20 (.080" -.090") galvanized steel tubing,'/,' x 1 '/4" HR flat steel and'/4" x 2'/4" HR flat steel. Finish: ProShiekie, color specified. Rails: Weldment comprised of 1.315" O.D. RS -20 (.080" -.090") galvanized steel tubing, and '/4" x 1 '/, HR flat steel. Finish: ProShield, color specified. Footer: Fabricated from 1.125" O.D. 11 GA. (.120") galva- nized steel tubing. Finish: ProShield, color specified. Mounting Plate: Fabricated from'/a" HR flat steel. Finish: ProShield, green. Hand Grip: Made from Polyester Resin. Hand Grips measure approx. 5'/," long x 2'/4" wide x 1 1/4" high. Handhold Panel: Solid color Permalenev, color specified. Belt: PVC belting, 5/16" thick, 300PIWtensionmting. Spacer Tube: Made from 6061-T6 aluminum'/,' O.D. x 1 Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield color specified. Fasteners: Primary fasteners shall be socketed and pinned tam- perproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Installation Time: SM -Approx. 2'/, boors DB - Approx. 3 % hours Concrete Req.: Approx. 2.6 cu. ft. Weight: SM - 120 lbs. DB - 124 lbs. Fall Height: Deck Height Installation Instructions 1 I (Direct Bury) Dig footing holes spaced as shown. 2) ]risen upper loop onto rails. 3) Drill through holes in rails into center loop with a'/4" or "F" (only) drill bit. Insert'/,' x'/,6" drive rivets in holes and hammer drive rivet pin in until flush with head. Refer to the Frame Assembly Detail & Plan View/Foming Layout. 4) Attach belt to framework using 3/a" x 1 '/." BHCS w/pin with'/." flat washers (large) and Y." low crown cap nuts with'/." SAE flat washers (small). Begin at the center of the upper loop on the frame assembly, continuing down both side rails. NOTE: Use a center punkt to stretch the bele into position on bolt ftangn Refer to the Belt Attachment Detail. 5) Attach footers to belt frame using 5/e' x I '/,' BHCS w/pin and Y." flange nuts w/pin. 6) Attach belt frame to deck using'/." x 1 '/." BHCS w/pin with'/,' SAE flat washers (small) and'/," standard hex nuts with'/." SAE flat washers (small). Refer to the Deck Attachment Detail. 7) Attach hand grips to belt using 3/." x 7/a" BHCS w/pin and mounting plates with Y." flange nuts w/pin. 8) Attach offset hanger clamps to posts at heights shown using 5" half clamps,'/," x 1 '/,' BHCS w/pin and Y." tee nuts. RWr to the Typical Offset Hanger Clamp Spec Sheet. O cs. 9) Attach handhold panels to deck using'/. -N' ,BHS w/pin w t %11 SAE flat washers (small) and Ys" flangemi!�/pia 10) Attach handhold panels to the offset haageMam sembges using %" x 3'/," BHCS w/pin, spacer tubes andNgangWts w/Mefer to the Handhold Panel Attachment Deta: M a r l l) Install 1/4" x'/,' drive rivets in all 5" halodtamps. I�r to th`eipical Offset Hanger Clamp Spec Sheet. 'ar O m 12) (Direct Bury) With belt climber in final position, pour concrete footings. Allow concrete footings to cure for a minimum of 72 hours before users are allowed to play on the structure. (Surface Mount) Drill'/," x 3" deep holes through footer plates using hammer drill and'/," masonry bit. Tap expansion anchors into drilled holes. Fasten footer plates to expansion anchors using '/," standard hex nuts with'/," flat washers. 13) Install protective surfacing before users are allowed to play on the structure. Ew953287nocu t#IW7600rtRlaeea91513370n RVI"lefthmdandrighthmdreds. 9/& landscape structures® DETAIL FRAME ASSEP _SE (2) Rails (2) 1/:' x'/,e' Drive Rivets SAFETY NOTE Choose a protective surfacing material that has a Critical Height Value a at least the height of the Highest Accessible Part/Fall Height of the adjacent equipment (Ret. ASTM F1487.) 160076a PLAN VIEW/FOOTING LAYOUT Y ;� $ Center Loop DETAIL BELT ATTACHMENT 40" Deck B 481/,' NOTE: Use a center punch to stretch the belt into position on bolt flange. 2) %" X 1 1/e' bo A V �� kn M00 Concrete Footing DETAIL DIRECT BURY Belt Frame t (2)3/;' Flange Nuts w/Pin c - a C, Concrete as b c > 7 Slab - _ Concrete _ Footing — Crushed NOTE: Sufficient protec- Rock five surfacing must cover 12" hardware to satisfy fall auu height requirements. PlavBoostW 143199 Conical ClimberTM, 401 0 2007 by Landscape Stmctures. N 0 cn n Sheet 2 of 2 DETAIL BHCS w/Pin SURFACE MOUNT (4)1/2" Standard Loose Fill Hex Nuts w11/ Protective =' Flat Washers Belt Frame Surfacing - (4)1/2" x 21/4" (2)'/;' Flange it on N is vil 2) Footers Subgrade Anchors (2)'/;' x 1 4e' BHCS w/Pin -- - - (2) Footers — bo A V �� kn M00 Concrete Footing DETAIL DIRECT BURY Belt Frame t (2)3/;' Flange Nuts w/Pin c - a C, Concrete as b c > 7 Slab - _ Concrete _ Footing — Crushed NOTE: Sufficient protec- Rock five surfacing must cover 12" hardware to satisfy fall auu height requirements. PlavBoostW 143199 Conical ClimberTM, 401 0 2007 by Landscape Stmctures. N 0 cn n Sheet 2 of 2 A/& landscape structurev Typical PlayBooster Post V r I I I I I 1 X11 CERTIFIED I (2) Typical Offset Hanger Clamp SAFETY NOTE [Helghtdtheadi�equip� roose a protective su"apng matenal that C' a Critical Height Value M at least the ight of Phe Highest Accessible PaN all (Rel.ASTM a87j 15307800 DETAIL PANEL ATTACHMENT (2) Typical Offset Hanger Clamp Assemblies post Flange Nuts � w/Pin s/;' x 3 s/," CS w/Pin DETAIL TENDERDECKS (2) Handhold Panels Flange uts w/Pin (4)3/," x 7/e' BHCS w/Pin W1 3/,11 SAE Flat Washers Sheet 1 of 2 02005 by Landscape Slmctures All rights reserved. Document#15307800 Mini Summit o -"_ Climber ting _-_.__._ .. C _< f —in Cn frn er a er= 0" :^ W Cn 0 153076 Mini Summit Climber, 40e1-48" Deck Sheet 1 of 2 02005 by Landscape Slmctures All rights reserved. Document#15307800 /bl PlayBooster" 153076 Mini Summit Climber, 40"-48" Deck landscape structures` Parts List Part# Description Qty. 152553 Mini Summit Climber, Specify Color ..................... 1 139563 Handhold Panel, Specify Color ................................ 2 105327 5" Half Clamp, Specify Color .................................. 2 113729 Offset Hanger Clamp, Specify Color ....................... 2 100610 '/f x %" Drive Rivet, AUSST ............. 2 113468 Spacer Tube, Specify Color ...................................... 2 153191 Support, DB, Specify Color ...................................... 1 153239 Support, SM, Specify Color ..................................... 1 139899 Summit Climber PO Hardware Package ............ 1 100196 3/e" x %" BHCS w/Pin, SST ..................................... 6 100198 3/e" x 1 '/r" BHCS w/Pin, SST .................................. 4 100351 3/8" Tee Nut, SST........ ................................................ 4 100353 Y." Flange Nut w/Pin, SST ....................................... 6 100365 3/s" SAE Flat Washer, SST ........................................ 6 124460 3/e" x 3 3/," BHCS w/Pin, SST .................................. 2 129111 Support Hardware Package ................................... 1 100198 3/s" x I '/e" BHCS w/Pin, SST .................................. 2 100362 '/e" Flat Washer, SST ................................................. 2 111391 2 Hole (SM) Hardware Package ........................... 1 100263 3/c" x 2'/:' Expansion Anchor .................................. 2 100327 3/ti' Standard Hex Nut, SST ...................................... 2 100362 3/a' Flat Washer, SST ................................................. 2 SM a Surface Mount DB = Direct Bury Specifications Mini Summit Climber: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Handhold Panel: Solid color Permalene", color specified. Support (DB): Weldment comprised of 2.375" O.D. RS -20 (.095" - .105") galvanized steel tubing and'/," x 3" mounting plate. Finish: ProShielde, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproofin design, stainless steel (SST) MASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Tlme: SM- Approx.'/, man how DB - Approx. 3/4 man how Concrete: 1.31 cu. ft. Weight: 86 lbs. SM 88 lbs. DB Fall Height: Deck Height Installation Instructions 1) (Direct Bury) Dig footing as shown. Refer to the Plan View & Di- rect Bury Details. 2) Attach offset hanger clamps to posts at height shown using 5" half clamps,'/e" x 1 '/s" BHCS w/pin and'/s" tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 3) Attach handhold panels to the face of the deck using 1/g" x'/g" BHCS w/pin with %" SAE flat washers and %" flange nuts w/pin. Refer to the Tenderdeck Detail. 4) Attach handhold panels to the offset hanger clamp assemblies using I&" x 3 '4" BHCS w/pin, spacer tubes and Ys" flange nuts w/pin. Refer to the Panel Attachment Detail. 5) Attach support to Mini Summit Climber using 3/s" x I'/g" BHCS w/pin with %" flat washers, as shown. Refer to the Direct Bury Detail. 6) Attach Mini Summit Climber or to the face of the deck using 3/8" x'/s" BRCS w/pin with 3/s" SAE flat washers, as shown. 7) (Direct Bury) With summit climber plumb and level, pour concrete footing. Allow concrete footing to cure a minimum of 72 hours be- fore users are allowed to play on the structure. (Surface Mount) Drill 3/s" x 3" deep holes through support plate using hammer drill and 3/s" masonry bit. Tap expansion anchors into drilled holes. Fasten support plate to expansion anchors using 3/," standard hex nuts with 3/s" flat washers. Refer to the Surface Mount Detail. 8) Install protective surfacing before users are allowed to play on the structure. v 0 O cs+ O C-.) rt; Ori O O rte] dhm ISO I landscape structures` DETAIL SURFACE MOUNT (2) 3/a" Standard Mini Summit Hex Nuts w/ 3/e' Climber Flat Washers — Concrete s Footing � Mini Summit_ (2) 3/5' )c 2 3/,' Support Climber Expansion Anchors °a 1 4 d a ° a a Concrete �- - - - Slab A -AA I A- - Crushed NOTE: Sufficient protective Rock surfacing must cover hardware to satisfy fall height require- ments. Mini Sur Climber Loose Fill Protective Surfacing DETAIL SAFETY NOTE Choose a pdecave sv at mYanal a�01 has a Critical Heist Value Y 61 least tlta height of the Highest Aazsside PVUFYI Heghl orale xjaamtegipna."a.IRel ASTM F1a81.) PLAN VIEW i Deck DETAIL DIRECT BURY I 42" O Finished 153078a0 Mini Summit Climber m G o_ Subgrade E M Concrete CD (2) '/;'x 1 Va" - Supportcc I3HCS w/Pin Si e C7 C 3/a" Flat Washers Support �c 3 —<{— Crushed Rock :P,- to i%; 12, ut _ 305 PlayBooster® 153076 Mini Summit Climber, 40" -4s" Deck Sheet of 02005by Landscape SVudures Arnghtsreserved. Document#15307800 j & landscape structures® NOTE: When using this deck, ALL enclosures and components are mounted on the 01 SIDE of the posts like the bubble panel shown above. I dm 42" 1070 DETAIL DECKHANGERCLAMP (8) 3/811 x 1 1/e BHCS w/Pin (4)1/4 " x a/a Drive Rivets (4) S' Half Clamps 111228 SAFETY NOTE Choose a protective surfetlrg ns-7--_ aledaThat has a Critical Height Value of et least the Night of the Highest Accessible PaNFall HeighlMMe a4amntequlprri (RO.ASTM FUBZ) 14582100 N 0 Deck a �^ CS) M �--4 --I (4)StuEs-< I r M �Gr a �+ U1 Post (4) Deck Hanger Clamps (4) 3/1 Flat Washers w/ a/a' Hex Patch Nuts uare Deck Landscape Seuomres All rights reserved Document #14582100 landscape structures, J--.1.SPECS14 145a210 o P55 Parts List Part# Description Qty. 145656-00 Tenderdeck, Specify Color ........................................ 1 105327-01 5" Half Clamp, Specify Color .................................. 4 106022-00 5" Deck Hanger Clamp, Specify Color ................... 4 119491-00 Hardware Package.... ........................... 1 100198-00 r/k" x 1 '/k" BHCS w/Pin, SST .................................. 8 100321-00 %" Hex Patch Nut, SST ............................................ 4 100351-00 r/k" Tee Nut. SST ........................................................ 8 100362-00 r/k" Flat Washer, SST ................................................. 4 100610-00 '/i' x %" Drive Rivet, SST ....................................... 4 Specifications Square Deck: Flange formed from 12 GA (.105") sheet steel con- forming to ASTM Al OIL Standing surface is perfo- rated with 1/i," diameter holes. Deck face has (4) slot- ted holes for face mounting components. The finished size measures 2 5/k" x 47" x 47". Finish: TenderTuftr, , color specified. Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShielde, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 1 man hour Weight: 119 lbs. PlayBooster° 111228 Square Deck Installation Instructions I ) Mark posts for the appropriate height of the deck you are installing. 2) Fasten hanger clamps to marked position on posts. See Detail on front of sheet. 3) Lift deck into position, lining up studs underneath deck with deck hanger clamp as shown. Attach with'/s" flat washers and 3/8" hex patch nuts. 4) Level deck and plumb posts. Install the drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 5) After all enclosures/components are installed, pour concrete foot- ings per the Typical Concrete Footing Detail Sheet. 6) Install protective surfacing before users are allowed to play on the structure. Ecv#5U2 Dw 40145821WFVI e41395/600.Rry1 TeMndeck. O r�l a/& landscape structures° SAFETY sel (:IKVS¢ 8 "el 61RIB T r112t(g131 th81 has a critical Height Value of st least the he,IS014001IM Helofn>aaa"a i w (H asni ® Ff48Zl Grtlilea 14582400 Configuration for Back to Back Decks at Same Height. 42" DETAIL 111231 Tria (3) Deck Hanger( (6) 3/a' Tee (3)3/e' Flat Washers w/ 3/;' Hex Patch Nuts DETAIL DECK HANGER CLAMP Post )eck cn o ( alf n Cla 's r mCris cfl (3) V4" x 5/e Drive Rivets (6) 3/8' x 1 14" BHCS w/Pin ular Tenderdeck by Lanascap structures. All rights reserved Document #14582400 k& landscape structures' J.\SPECS\145U4582400. P85 Parts List PlayBoosterO 111231 Triangular Tenderdeck Part# Description Qty - 145657 -00 Tri -Deck, Specify Color ............................................ 1 105327-01 5" Half Clamp, Specify Color .................................. 3 106022-00 Deck Hanger Clamp, Specify Color ........................ 3 120203-00 Triangular Deck Hardware Package ................... 1 100198-00 3/." x 11/," BHCS w/Pin, SST .................................. 6 100321-00 1/s" Hex Patch Nut, SST ............................................ 3 100351-00 1/." Tee Nut, SST ........................................................ 6 100362-00 1/." Flat Washer, SST ................................................. 3 100610-00 1/4" x 1/." Drive Rivet, AL/SST................................. 3 Specifications Triangular Deck: Flange fomted from 12 GA (.105") sheet steel con- forming to ASTM AI011. Standing surface is perfo- rated with 1/„' diameter holes. Deck face has (4) slot- ted holes for face mounting components. The finished size measures 2 1/,' x 37 3/,". Finish: TenderTuffe", color specified. Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShieldm, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproofin design, stamless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx.'/2manhour Weight: 61 lbs. Installation Instructions 1) Mark posts for the appropriate height of the deck you are installing. 2) Fasten deck hanger clamps to marked position on posts. See Detail on the front of this sheet. 3) Lift deck assembly into position, lining up stud underneath deck with deck hanger clamp as shown. Attach using'/,' hex patch nuts with 3/t" Hat washers. With deck level and posts plumb, final tighten all hard- ware. 4) Install'/4"x1/." drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 5) After attachment of enclosures and components is complete, pour concrete footings. Allow concrete footings to clue a minimum of 72 hours before users are allowed to play on the structure. 6) Install protective surfacing before users are allowed to play on the structure. YT O c-^ c 7 O �m M ' o n Eco#52268 Docw¢n1#14562400Ml #13954200.R,Ie Tri -D k. U� landscape structuress KICK PLATE KICK PLATE (FOR 16" RISE) Typical Mainstructure Post SAFETY NOTE Choose a prolective suRedng mater"' Nat has a Critical Height Value of et least the height of the Highest Accessible Par=11 Height of Ne aclacent equipment. (Ref. ASTM Ff487J 16574300 DETAIL KICK PLATE ATTACHMENT (FOR 6" OR 8" RISE) (4) 3/;' x 1 BHCS w/Fin wit3lFlat Washers DETAIL Typical KICK PLATE ATTACHMENT Mainstructure (FOR 16" RISE) Post ll Standard Nuts wit 'I-" Flat Washers KU -4 _ Po cn O C") \ Lower (4)'/;' x 1'/e"Ldwer Deft - Deck BHCS w/Pin w/'/;' Flat9 Stan Washers <}ie*Aluts w ' " DETAIL �lat�asnerp T KICK PLATE ATTAC�NT J KICK PLATE (FOR 6" OR 8" RI ) (FOR 6" OR 8" RISE) per Dec,) Deck Kick Plate io �O 0 / Lower Deck Kick Plate (4)'/e" x 11/e" BHCS Lower w/Pin w/ %" Flat Deck Washers (4)'/;' Standard Hex Nuts w/'/," Flat Washers NOTE: Kick Plates mount to face of lower deck. 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888.574-4678 LSI Install Help 888338-6574 LSI Direct 763-972-1. � 2011 by Landscape Structures All rights eservAd Document#18161000 U& landscape structures J: tSPECW 81 \18161000. Pas Parts List PlayBoostee 121948 Kick Plates, Tenderdecks, 6", 8" & 16" Part# Description Qty - 121819 -00 Kick Plate (For 6" or 8" Rise), Specify Color........ 1 121818-00 Kick Plate (For 16" Rise), Specify Color ................ 1 156058-00 Kick Plate Tenderdeck Hardware Package........ 1 100198-00 1/e" x I -/e" BHCS w/Pin, SST .................................. 4 100327-00 3/e" Standard Hex Nut, SST ...................................... 4 100362-00 1/e" Flat Washer, SST ................................................. 8 Specifications Kick Plate: Fabricated from 11 GA (.120') HR flat steel. Finish: TenderTuft111, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) MASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 1/4 man hour Weight: Kick Plate (For 6" or 8" Rise) 13 lbs. Kick Plate (For 16' Rise) 23 lbs. Installation Instructions I ) Locate kick plates as labeled on your plan drawing. 2) Attach kick plate using 3/s" x 1 1/r" BHCS w/pin with 3/e" Flat washers and 14" standard hex nuts with 3/e" Flat washers, as shown. NOTE: Kick plates mount to face of lower deck. 3) Install protective surfacing before users are allowed to play on the structure. N O ZES2 O —4 --t C') �r m M73 r t7 rn SAFETY NOTE Choose a pmtecava wHaarq material that has a Cntical Height Value M at least the height IN the Highest Accessible ParVFaO NOTE: When using this ISO 14001 I Haghtoftheagacent"uWwL(Rer ASTM deck, ALL enclosures and �IZI certified r'aez landscape components are mounted 14582700 structures° on the OUTSIDE of the 411 b bbl I DETAIL (6) 5" H Clamps (6) t/," x Drive R pos i e e u a pane shown below. DECK BRACE DETAIL Outside 2 Holes Use (2) DECK HANGER CLAMP '/," x T/," BHCS w/Pin Deck w/ 3/8" Flat Washers Post / Deck (12)"1 x 1 t/e" BHCS w/Pin (2) Deck Braces 0 n 0 Inside 2 holes Use (2)'/a" x 1" Flat Head Cap Screws & Standard Hex Nuts w/'/;' SAE Flat Washers 0 r' NOTE:Deck brace fits inside deck face. -0 (6) Deck Hanger Clamps (12)'/;' Tee Nuts (6)'/;' Flat \AheFure w/ a/ " Typical Perforated Areas + 36 %" u Deck Bra x 1 '/;'BHCS w/Pin Flat Washers & 3/," Ird Hex Nuts w/'/," Flat yBoostee 1 • • • - • 601 .7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888-438-6574 LSh Direi KIM Ln 0 (2)"1 Standard Hex Nuts Document #20738800 k& landscape structures, Parts List PlayBooster° 178710 Hexagon Tenderdeck Part# Description Qty. 207385 Deck Brace, Silver ..................................................... 2 105327 5" Half Clamp, Specify Color .................................. 6 106022 Deck Hanger Clamp, Specify Color ........................ 6 145659 Hex Deck, Specify Color .......................................... 2 137121 Hex Deck Hardware Package ................................ 1 100196 '/," x'/," BHCS w/Pin, SST ..................................... 4 100198 '/," x 1 '/," BHCS w/Pin, SST...... ........................... 15 100327 3/," Standard Hex Nut, SST ..................................... 11 100351 '/," Tee Nut, SST ....................................................... 12 100362 3/," Flat Washer, SST ................................................ 16 100365 '/."SAE Flat Washer, SST ........................................ 4 100610 '/," x'/," Drive Rivet, AUSST................................. 6 100321 3/," Hex Patch Nut, SST ............................................ 6 137091 34" x I" Flat Head Cap Screw, SST ......................... 4 Specifications Hex Deck: Flange formed from 12 GA (.105") (2,67 mm) sheet steel conforming to ASTM A 1011. Standing surface is perforated with'/„” (7,94 mm) diameter holes. Deck face has (4) slotted holes for face mounting compo- nents. The finished size measures 2'/," x 36" (66,68 num x 914 mm) per each of the six sides for an overall dimension of 78" (1981 mm) face to face or 87" (22 10 rum) point to point. Finish: Tendetfuff' , color speci- fied. Deck Brace: Fabricated from'/," x 1 3/4" x 28 1/2" long zinc plated steel strap. Finish: Pro.Shield', silver in color. Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShield', color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx.2'/2manhours Weight: 284 lbs. Installation Instructions 1) Mark posts for the appropriate height of the deck you are installing. 2) With deck on ground, position deck braces inside & under deck as shown and fasten outside two holes of deck braces to hex deck half using'/," x'/," BHCS w/pin with'/," flat washers and'/," standard hex nuts. Fasten inside two holes of deck braces to hex deck half using 3/," x I" flat head cap screws and'/," standard hex nuts with %" SAE Flat washers. Fasten tenderdeck members together using 3/," x 1 1/," BHCS w/pin with 3/," flat washers and'/," standard hex nuts with flat washers. 3) Fasten hanger clamps to marked position on posts. See Detail on the front of this sheet 4) Lower deck assembly into position, lining up stud underneath deck with deck hanger clamp as shown. Attach using'/," hex patch nuts with 34" flat washers. 5) Level deck and plumb posts. Install the'/," a %" drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec sheet. 6) After all enclosures/ components are installed, pour concrete foot- ings per the Typical Concrete Footing Detail sheet. Allow concrete footings to cure a minimum of 72 hours before users are allowed to play on the structure. 7) Install protective surfacing before users are allowed to play on the structure. �xaioozxa ooc,me,n xzm3eeoo „pi.«, xrv3am.cnaoae s,ra wn n,meR. N 0 O �O O O t �� �r i „ o D o CF �xaioozxa ooc,me,n xzm3eeoo „pi.«, xrv3am.cnaoae s,ra wn n,meR. / l dhm SAFETY NOTE JU/� G,009e e prWecavO 6urleang malenal Nal /� h89 0 Cd+ical Height Value W 01 10891 +h0 IS0 14001 hMagM „Ba°egenlfeµ pma a 1(Re STM landscape �IZI Ceri1!iad F'.e 18598000 structures` DETAIL (4)9/a"x1/a, PANEL ATTACHMENT .a BHCS w/Pin _ (4) 5" Half Typical (2) Infill (4) HangerClamps PlaPostBooste Panels 24 Vi ; Clams Post a e, P (4) / Tee �----I I Nuts i 1 ' 1 TOP of (6) e/e �. (4) %" x 2 1/2" clamp Flange o BHCS w/Pin a Nuts w/Pin w/ a/," SAE 1 Flat ° Washers (6) %" x e/6 r BHCS w/Pin(4)e/," Flange a (4) /a' O.D. x 1 /„' (2 ) Infill w/ /,” SAE u Spacer Tubes Panels Nuts w/Pin Flat 00 Washers 0 1 j DETAIL HANDRAIL ATTACHMENT ° (3) Rails Step (2) Handrails _ Section ToP of 32" Dock Clamp •, o _ _ -VOP Of ,i it _ -__ peck ti (4) a/e"% -= -` -_ 1 -Step Standard Section Hex Nuts w/ e% SAE (4) a/a' x 1 1/8" ° ° x 2" Flat Washers BHCS w/Pin _ _ __ __ ___ _ _ __ _ BHCS w/Pin a _ _ _ ___ w/ els' SAE (6) /e' Low I AE - -- -- =- w S e _ _ _ _ _ ° __ __ __ _ ___ _ _ ___ Flat Washers Crown Cap Nuts Flat :-_-:_-' -__----'-_ -_- w/a/;'Fender Washers _`-`_-:'r='= '__________ t -_'-= - _ _ _ _ Transfer Dark Washers ___-- (4)%"x1 a/f' BHCS w/Pin Lower Rail _ w/ a/," SAE Flat -_-_---- _ Washers 1 -Step = m Deck Support Section (Lower) (4) a/," Low Crown o Cap Nuts w/ e/e' SAIF o -_ _ •° Flat Washers C3 Standard Hex Nuts w/ a/," m ".-... SAE Flat Washers y Pidiective O 3/0, x 1 ,/e l r Surfacing BHCSw/Pince la� NOTE: Protective surfacing w/ a/," SAE adjacent to the transfer deck Flat Washers o C) be accessible. PlayBoosteti 184354 Transfer Module, 32", w/Handrails Sheet 1 oft 02014 by Landscape Stmcmras All rights reserved Document #20402800 k14 landscape structures Parts List PlayBooster{" 184354 Transfer Module, 32", w/Handrails Part# Description Qty. 100610-00 I/," x'/1" Drive Rivet, AL/SST................................. 4 105327-01 5" Half Clamp, Specify Color .................................. 4 185741-00 Steel Haager Clampp, Specify Color ......................... 4 181371-00 Deck Support (DB), Specify Color .......................... I 181373-00 Deck Support M), Specify Color .......................... (S 1 181374-00 Step Support ( B), Specify Color ........................... 1 181376-00 144696-00 Step Support (SM), S ci Color ........................... I -Step Section, Sppeeccify Color 1 2 .................................. 175516-00 1 -Step Handrail, Scit Color ................................ 2 152641-00 Lower Rail, Specify Color ........................................ 1 153398-00 Transfer Deck, Specify Color ................................... 1 184254-00 Infill Panel, Specify Color ........................................ 2 113468-00 7/e" O.D. x 1 I /I," Spacer Tube, Specify Color...... 4 204037-00 Transfer Module Hardware Package ....... ___ ..... 1 100173-00 3/8* x 2" BHCS w/Pin, SST ....................................... 6 100196-00 3/, x 7/," BHCS w/Pio, SST .................................... 16 100198-00 3/, x 1 3/," BHCS w/Pin, SST ............................ .... 16 100327-00 3/," Standard Hex Nut, SST ..................................... 16 100351-00 3/," Tee Nut, SST ........................................................ 8 100353-00 %" Flange Nut w/Pin, SST ....................................- 10 100365-00 14" SAE Flat Washer, SST ....................................... 58 113027-00 34" x 1 34" BHCS w/Pin, SST .................................. 4 100174-00 3/," x 2 i/," BHCS w/Pin, SST .................................. 4 100378-00 '/." Fender Washer, SST ............................................ 6 100349-00 3/a" Low Crown Cap Nut, SST ................................. 12 111393-00 4 -Hole ISM) Hardware Package ...... _................... 1 100263-00 3/3" x 2 /," Expansion Anchors ................................ 4 100327-00 3/," Standard Hex Nut, SST ...................................... 4 100365-00 1/," SAE Flat Washers, SST ...................................... 4 121256-00 2 -Hole ISM) Hardware Package ........................... 1 100263-00 1/: x 2 /," Expansion Auction ................................ 1/, 2 100327-00 Standard Hex Nut, SST ...................................... 2 100365-00 '/," SAE Flat Washers. SST ...................................... 2 DB -Direct Bury SM -Surface Mount SDeciflcatlons Deck: Flange formed from 12 GA (.105") sheet steel con- forming to ASTM A1011. Standing surface iserfo- rated with 5/ia' diameter holes and measure 29" per (2) sides. Finish: TenderTuft"^, color specified. Railings: Weldment comprised of formed I Y." O.D. x 1 I GA (.120") steel tubing. 3/I," thick HR flat steel, l/1," thick HRPO steel plate and 3/, "O.D. x 11 GA. (.120") stain- less steel tubing. Finish: Tenderruff, color specified. Step Sections: Formed from 12 GA (.105") sheet steel conforming to ASTM A101 I. Standing surface is 243/x' wide x 14" deep and is ppeerrfforated with'/I," diameter holes. Fin- ish: TenderTufl;color specified. Spacer7Lbe: Made from 6061-T6 aluminum 7/," O.D. x 1 Finish: ProShields, color specified. Infill Panel: Solid color Permalenea panel, color specified Deck Support: Weldment comprised of 3 %" O.D. RS20 (.125") gal- vanized steel tubing and 1/a' O.D. is 5" long rod. Fin- ish: ProShield, color specified Step Support: Weldmentcomprised of1.660O.D.RS20(.080"-.095) and 1 3/," x 13/;' x'/," HR angle. Finish: ProShiel , color specified. Sri. Hanger Clamp: Weldment comprised of/;' HRPO flat steel. Finish: ProShields, color specified. Clamp: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)perASTM F 8 97 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: SM- Approx. 3 man hours DB - Approx. 4 plan hour Concrete Req.: Approx. 2.94 cu. ft. Weight: SM - 195 lbs. DB - 210 His. Fall Height: Deck Height Installation Instructions I (Direct Bury) Dig footings as shown. Refer to your Plan View/Foot- mg Layout. 2) Attach the deck support to the transfer deck using 3/,' x 7/s" BHCS w/pin and 3/ " low crown cap nuts with 3/," SAE flat washers. NOTE: Make sure /e" radon support is under support strop on deck as shown. Refer to the Deck Support Attachment Detail. 3) Attach the 1 -step section to the transfer deck using 3/," x I It," BHCS w/pin with 3/," SAE flat washers and 3/," standard hex nuts with 3/s" SAE flat washers. 4) Attach the 1 -step section to the face of the mainstructure deck using 1/s" x I its" BHCS w/pin with 3/," SAE flat washers and 3/," standard hex nuts with 1/," SAE flat washers. 5) Attach the step support to the 1 -step section (lower) using 3/," x 1 '/s' BHCS w/ in with /," SAE flat washers and 3/," standard hex nuts with 1/," SAE flat washers. Refer to the Step Support Attachment Detail. 6) Attach the I -step section (lower) to the transfer deck using 3/r" x I Y." BHCS w/pm with 1/," SAE flat washers and 1/," standard hex nuts with 3/," SAE flat washers. 7) Attach steel hangger clamps to posts at heights shown, using 5" half clamps, 3/," x 7/," BHCS w/pm and 3/," tee nuts. Refer to Panel Attchment Detail. 8) Attach infill panels to steel hanger clamps, using 1/ 2 3/," BHCS, 7/3" O.D. is 1 I I/1, spacer tubes and 3/," flange nuts w . Refer to Panel Attachment Detail. u' � Cf 9) Attach the handrails to the steps using 3P,4zC Bw/pin wi 3/e' SAE flat washers and 3/," low crown caifnuialwith"is" fen sh- ers. Refer to the Handrail Attachment D,ai. 1 10) Attach the handrails to the infill panels ucill�3y,' xs" BHpgy�q�in with 1/," SAE flat washers and 3/," flange.Q t -/pq 1 s r 11) Attach the lower mil to the transfer deck it xBH(in with 1/." SAE flat washers and %11 low cr a p n " ith 3/r SAE flat washers. D, O 12) Attach the lower rail to the l -step section(lower) usin�l," x 2" BHCS w/pin with'/s" SAE flat washers and 3/,° low crown cap nuts with 3/s" fender washers. Refer to the Handrail Attachment Detail. 13) (Direct Bury) With transfer deck and steps level and supports plumb, pour concrete footings. Allow concrete footings to cure a minimum of 72 hours before users are allowed to play on the structure. (Surface Mount) Mark holes for expansion anchors on concrete slab through support plates. Detach the module from the mainstmcture and slide module aside, drill 3/," is 3" deep holes on marks using hammer drill and 1/a' masonry bit. Reposition module over drilled holes and tap expansion anchors into drilled holes. Fasten support Vales to expansion anchors using 3/," standard hex nuts with 1/s" AE flat washers. Reattach module to structure. 14) Install I/," x'/," drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 15) Install protective surfacing before users are allowed to play on the structure. Eco0100178 oxvn=120102d00replies 18598000. RMIh mpwkege. a/za landscape structures® PLAN VIEW PLAN VIEW FOOTING LAYOUT FOOTING LAYOUT RIGHT HAND STEPTypical Typical LEFT HAND STEP Concrete Concrete 32" Deck Footina Footina I 32" Deck SAFETY NOTE CYaoae a pofecOve aulearq material leal llda a Critical Heigef Value of et leaat fila eeigM of tee Mgeeat A[cesside PaNfell HeIgM of Vleacteranl equpmeM. (Ref. ASTM F14BT) 204022a DETAIL STEP SUPPORT BURY Loose Fill Protective__.Step Support N ;k Subgrade Concrete 22 °/e' 19 a/s' .,..,..�..� 3 ,/ '. 1 g a/e l 22 ,/e ... l (Lower) Crushed 95.« 95 Rock 8" 200 DETAIL DETAIL DETAIL SURFACE MOUNT DECK SUPPORT BURY SURFACE MOUNT STEP SUPPORT (2) °/." Standard Loose Fill 4 '/;' Standard Deck Support Hex Nuts w! °/e° 1 -Step Protective "°'� .x SAE Flat Section �.;..,.. Hex Nuts w/ /," Washers Surfacing SAE Flat (Lower) Washers (2) 3!, x 2'/4' —Step Support Expansion E (4) a/;' x 2 a/°• Anchors Subgrade<`- Expansion _ _ ..,- _ r7 Anchors ° NOTE: Sufficient protec- Concrel tive surfacing must cover hardware to satisfy fall Crushed height requirements. Rock DETAIL DECK SUPPORT ATTACHMENT m (2) 14 .1 x 7/e BHCS w/Pin Rock Deck Support Rock DETAIL STEP SUPPORT ATTACHMENT (2) °/l Low Crown Cap Nuts w/ °/," SAE Flat Washers NOTE: Make sure'/," rod on support is under support strap on deck as shown. (4) Standard Step . ;o Hex Nuts Support Cff (4)'/;' x 1'/;" w/'/," SAE Flat pp p BHCS w/Pin Support Washers w/ 3/a' SAE Flat Washers PlayBoostell 184354 Transfer Module, 32", w/Handrails Sheet 2 of 2 a ll l a 02014byl_. a ape&8u tares Aurigbl.ree.,ed Document #20402800 alk landscape structures® Deck I 20'/=521 42" 1070 Typical PlayBooster Post (2)TypicalOffset I ' F I ' 1 I ' I ' I ' o I ' I ' I I I ' I ' I ' - I � p I y, NOTE: Steering Wheel Infill Panel available. Re- Balcony Deck fer to the Wheel Spec Sheet. I � I , I , I , I ' I ' I ' I I ' I I I I Protective,.– Surfacing rotective,.–Surfacing SAFETY NOTE Cnoose a pmecwe sudadlg material Ihat lsioie �l�/� //��//��+ has a Cnlical Height Value of at least me W14003 , Helgnl ofheight flhe a]lathe gcentsea Pmsaht (ReIaASTM I I F1487) i Cer,i lletl 14608100 — :� \\ \ \ DETAIL � 3/,' x 1^WHEEL ASSEMBLY Sp;ring Pin Wheel ---41 AA I I WH)3Xw/Ain Wheel \� a 002)ts Flange Wits w/Pin V(2)'/ x 2'14" �� _ klil w/Pin Wheel Bracket Wheel Clamp Refer to Wheel Assembly Details on sheet 2. j DETAIL Wheel BARRIER/BALCONY DECK (3 1/" SAE Flat Wasers(3rown C)3wn Ca Ei Cap Nuts I I I 1 � 1 1 I 1 I 1 I e 1 I 67 1 I 1 I 1 Balcony 111240 Ba (4) a/," Standard NNuts w/ 3/a" SAE Washers PH) A '/ x 1 '/e' w/Pin o wNVheel Sheet 1 of 2 Document#20444100 I Balcony n ------------ Dedc___-_ n (3) 3/,' SAE PI) o m a Washers (3 Barrier Tabs N Q I I I 1 � 1 1 I 1 I 1 I e 1 I 67 1 I 1 I 1 Balcony 111240 Ba (4) a/," Standard NNuts w/ 3/a" SAE Washers PH) A '/ x 1 '/e' w/Pin o wNVheel Sheet 1 of 2 Document#20444100 jtl�l. landscape structures, Parts List PlayBooster{' 111240 Balcony Deck, w/Wheel Part# Description Qty. 146086-00 Balcony Deck, Brown ................................................ I 122586-00 Barrier, Specify Color ............................................... 1 108432-00 Wheel, Specify Color .......................... 1 127242.00 Steering Wheel Bracket, Specify Color ................... 1 127207-00 Wheel Clamp, Specify Color .................................... 1 105327-01 5" Half Clamp, Specify Clamp ................................. 2 113729-00 Offset Hanger Clamp, Specify Color ....................... 2 204450-00 Barrier Balcony Deck Hardware Package ......... 1 100198-00 3/a" x 1 '/s" BHCS w/Pin, SST .................................. 7 100203-00 '/a" x 2'/." BHCS w/Pin, SST .................................. 2 100349-00 3/s" Low Crown Cap Nut, SST .................................. 3 100351-00 '/a" Tee Nut, SST ........................................................ 4 100365-00 3/1" SAE Flat Washer, SST ........................................ 6 100610-00 14" x'/s" Drive Rivet, AL/SST................................. 2 148628-00 Wire/Pipe Barrier Hardware Package 100196-00 '/r" x'/3" BHCS w/Pin, SST ..................... 100353-00 '/a" Flange Nut w/Pin, SST ....................... 118452-00 '/I." x 1" Spring Pin, SST ........................ 148623-00 Cap, White ................................................. 121071-00 Tenderdeck Hardware Package 100198-00 V." x I V." BHCS w/Pin, SST..... 100327-00 '/." Standard Hex Nut, SST ......... 100365-00 3/s" SAE Flat Washer, SST .........- Specifications Deck: Fabricated from 12 GA (.105") sheet steel conform- ing to ASTM A1011. Standing surface is perforated with'/Is" c iamelerholes. The fnushed size measures 2'/s" x 34" (straight edge) x 17" radius (curved edge). Fin- ish: TenderTuff"a, color specified. Barrier: Weldment comprised of " solid steel vertical rails, ) '/r" O.D. steel horizontal rails with 203 or 303 stainless steel welded inserts with 5/s' internal threads. Finish: TenderTulf. color specified. Wheel: 12" diameter cast A356 aluminum alloy. Finish: TenderTuff, color specified. Wheel Bracket: Weldment comprised of formed '/,,"plate and%"O.D. stainless steel shaft. Finish: ProShield*, color speci- fied. Wheel Clamp: Formed from'/,;' x 2" HRPO zinc -plated. Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod - net installation/specifications). Installation Time: Approx. I '/r man hours Weight: 125 lbs. Fall Height: 8" -72"(0,20m -1,83m) Installation Instructions I) Attach balcony deck to tenderdeck using '/3" x I '/3" BHCS w/pin with 3/s" SAE Hat washers and'/," standard hex nuts with'/r" SAE Hat washers. Refer to the Tenderdeck Detail. 2) Attach offset hanger clamps to posts at height shown using 5" half clamps. '/," x I '/e" BHCS w/pin and'/R' tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 3) Attach barrier tabs to balcony deck using'/s" x I '/r" BHCS w/pin with Ys" SAE Hat washers and'/s" low crown cap nuts with %" SAE flat washers. Refer to the Barrier/Balcony Deck Detail. 4) Attach barrier to offset hanger clamps using'/s" x 2'/." BHCS w/pin, as shown. 5) Attach wheel bracket and wheel clamp to barrier in desired position using I/," x'/s" BHCS w/pin and %" flange nuts w/pin. Slide wheel and cap onto wheel bracket shaft and tap'/,." x 1" spring pin through cap and shaft. Refer To The Wheel Assembly Details on sheets 1 & 2. 6) Install'/." x'/s" drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 7) Install protective surfacing before users are allowed to play on the structure. Eur NOIOOIPC poinnunt N2MMIm R91m p1.8630u0. RryLrN hvdware paclage. N o_ CD n eJr t - n Cr. r �rn M. m - 3 CD co Eur NOIOOIPC poinnunt N2MMIm R91m p1.8630u0. RryLrN hvdware paclage. j & landscape structures* -rinSpon DETAIL NOTE: To assist in the alignment of the cap to the wheel bracket shaft, tap spring pin through cap approximately Y,". Orient spring pin to groove on wheel bracket shaft. Slide cap in place and tap spring pin though cap and shaft until flush. r® 111240 Bal (CAP BACK VIEW) Spn4x t°- ng Pin Deck, w/Wheel Sheet 2 of 2 ® 2014 by Landscape Stmctures All lights reserved. Document #204444100 V-1 trm =<rn i m g� L D ut 0 Sheet 2 of 2 ® 2014 by Landscape Stmctures All lights reserved. Document #204444100 In � SAFETY NOTE V Choose a protective aWetlrq materiel Nat has a Critical Heigh Value of et leaal the 1�7V®cA Might of the Highest ACCesaitNe ParVFall Certified FHe 8'oftMa4acerll equipment (Re1.ASTM landscape structures` DETAIL 13638700 PANELATTACHMENT (2 Typical Offs et Hanger Clamp ssAemblies (12) 3/,' Flange Typical Nuts w/Pin Mainstructure / \ Posts \! I i S Is ° E I ° I I li Slant Window M Panel I I I O 0 DECK MOUNT (12) 3/,' x 7/,' BHCS w/Pin w/3/,' SAE Flat Washers 0 (2)//," Flange Nub w/Pin Spacer Tubes Slant Window Section Window DETAIL TENDERDECKS a/," Flan is w/Pin S NOTE: The Slant Window Panel Is preasserMed at the factory. The drawjpwis eModedIM referencea4y, ge M r, w/Pin x 3 a/,' w/Pin wzr:.. ' IIWAIK� �� • • 601 7TH STREET SOUTH. DELANO, MINNESOTA 55328-8605 888-5744678 LSI In>lall Help 688438-6574 LSI Direct 763-972-5200 Int. FAX 176 31 972-3185_ Document #18204200 1h landscape structures' Parts List PlayBooster" 115222 Slant Window Panel Part# Description Qty. ABOVE DECK 105327 5" Half Clamp, Specify Color .................................. 2 113729 Offset Hanger Clamp, Specify Color ....................... 2 113468 Spacer Tube, Specify Color ...................................... 2 114015 Slant Window Panel, Specify Color ........................ 1 100610 1/4" x 3/4" Drive Rivet, AL/SST................................. 2 182016 Slant Window Assembly, Specify Color .............. 1 108111 Slant Window Section, Specify Color ..................... 1 108955 Top/Bonom Brace, Specify Color ............................ 2 108956 LHRH Brace, Specify Color .................................... 2 123797 Slant Window............................................................. 1 136327 Slant Window Hardware Package ........................ 1 100196 1/." x 7/." BHCS w/Pin, SST .................................... 12 100353 3/g" Flange Nut w/Pin, SST.... ........... ................ 12 100365 3/," SAE Flat Washer, SST ....................................... 12 124900 Tenderdeck Mounting Hardware Package ......... 1 124460 3/." x 3 3/," BHCS w/Pin, SST .................................. 2 100196 3/." x 7/a" BHCS w/Pin, SST ..................................... 4 100198 1/." x 1 Y." BHCS w/Pin, SST .................................. 4 100351 1/." Tee Nut, SST ...... -................................................ 4 100353 3/." Flange Nut w/Pin, SST ....................................... 6 100365 3/," SAE Flat Washer, SST ................... _................... 4 BELOW DECK 105327 5" Half Clamp, Specify Color .................................. 4 113729 Offset Hanger Clamp, Specify Color ....................... 4 113468 Spacer Tube, Specify Color ...................................... 2 113464 Angled Panel Bracket, Specify Color ...................... 1 114015 Slant Window Panel, Specify Color ........................ 1 100610 1/4" x 3/," Drive Rivet, AL/SST................................. 4 182016 Slant Window Assembly, Specify Color .............. 1 108111 Slant Window Section, Specify Color ..................... 1 108955 Top/Bottom Brace, Specify Color ............................ 2 108956 LH/RH Brace, Specify Color .................................... 2 123797 Slant Window .................... --..................................... 1 136327 Slant Window Hardware Package ........................ 1 100196 1/," x 7/," BHCS w/Pin, SST .................................... 12 100353 3/," Flange Nut w/Pin, SST ...................................... 12 100365 3/," SAE Flat Washer, SST ....................................... 12 124947 Below Deck Mounting Hardware Package......... 1 124460 3/i x 3 3/," BHCS w/Pin, SST .................................. 2 100195 3/, x 3/," BHCS w/Pin, SST ..................................... 4 100198 1/.' x 13/." BHCS w/Pin, SST .................................. 8 100203 % x 2'/4" BHCS w/Pin, SST .................................. 2 100351 3/," Tee Nut, SST ........................................................ 8 100353 3/," Flange Nut w/Pin, SST ....................................... 6 Specifications Permalene' Panel: Solid color met measures 35 3/," wide x 41" high, color specified. Slant Window: .177" thick clear polycarbonate. Slant Window Section: Rotationally molded from U.V. stabilized finear low density polyethylene, color specified. Braces: Solid color, to match panel. Angled Panel Brkt: Weldment comprised of .190" thick 5052 aluminum formed angle with (2) 6061-T6 aluminum threaded tubes 1 '/ "0 D. x 1 '/2 long. Finish: ProShields, color specifid. Spaceribbe: Made from 6061-T6 aluminum V." O.D. x 1 Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners sball be socketed and pinned nor perproof m design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Above Deck Approx. I man hour Below Deck ApppVrox. I '/, man hours Weight: Above Deck Xlibs. Below Deck 67 lbs. Installation Instructions ABOVE DECK (See Sheet I of 2) 1) Attachpant to the face of the deck, using 3/." x, 7/," BHCS w/pin with 3/," SAE flat washers and'/.' Flange nuts w/pm. See Detail. 2) Attach offset banger assemblies to posts at height shown, usin half clamps and 3/," xi Y." BHCS w/pin with 3/," tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 3) Attach panel to offset hanger assemblies. using 3/.' x 3 3Q' BHCS w/pnh spacer tubes and 3/.' flange nuts w/pin. See Panel Attachment Detail. 4) Attach slant window assembly to panel as shown, using 3/," x?/s" BHCS w/pin with 14" SAE flat washers and 3/." flange nuts w/pin. 5) Install protective surfacing before users are allowed to play on the structure. BELOW DECK (See Sheet 2 of 2) 1) Attach offset banger assemblies to posts at height shown, using half clamps and 3/," xi Y." BHCS w/pin with %" tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 2) Attach angled panel bracket to bottom of papal usingg 3/," x s/," BHCS w/pin and 3/," flange nuts w/pin. See Below deck Rfount. 3) Attach angled panel bracket with panel to offset rail hanger assem- blies using 3/," x 2 '/4" BHCS w/pm. See Below Deck Mount. 4) Attach top of panel to offset rail hanger assemblies, using 3/," x 3'1 " BHCS w/pin spacer tubes and 3/.' flange nuts w/pin. See Typical Attachment'�o Post Detail. 5) Attach slant window assembly to panel as shown, using 3/8" x Y.' BHCS w/pin with 3/," SAE flat washers and 3/," flange nuts w/pm. 6) Install'/"x3/," drive rivets in all 5" half clamps. Refer to the Typical Offset Imager Clamp Spec sheet. 7) Install protective surfacing before users are allowed to play on the structure. CD n oC-1 w6 h—C I qa_ ! (rr) a �-1 i ➢ D 7J 3 Y` O J Fin NS 12 poen"ate18204200 rtpl MIM38700.Aa Slav,Willow A. Iy w cub Lia. A& landscape structures (2)%" Flange Nuts w/Pin V (2)5/;"x2 '/i BHCS w/Pin Typical Mainstructure______4 Post i i y 1, 48" Or Higher Deck p� e . (12)3/," Flange Nuts w/Pin Spacer ubes 1411 x 3 0/4 11 ICS w/Pin )s/;"x s/e" -ICS w/Pin 0 Slant Window Panel o 136387a0 NOTE: Slant Window Section can be rotated to shift window direction. (4)Typical Offset Hanger Clamp Assemblies o (12) 31;' x 7/," BHCS w/Pin w/'/," SAE Flat Washers See — 1 1p/Panel ht Table (4)'/;' Flange Angled Panel Nuts w/Pin ' 13radcet BELOW NOTE: K .live The Slant Window Panel is MOUNT 48 :ing preassembled at the factory. x �o The drawing is exploded for 56" And 14'/,68 reference only. Higher o Io 115222 Slant Window Panel Window Section `> U _ c'� s Document#18204200 j & landscape structures - Typical PlayBooster Post \ 01 Panel clamp 01 6 1 1 CERTIFIED Typical 1 1/," x 141/," Opening 1 1/2' x 6 3/4" 3 35` Zoo • Panel ° 0 DECK MOUNT (2)%" Nuts M SAF7h1$ TY NOTE Choose a me sWearq materiel Thal has a Critical Height Velue of al leas) Ne height of the Highest AccessiCle Pan/Fall MegMofMre agacem aqupmenl. (Ref ASTM Ff187) 14023700 DETAIL PANELATTACHMENT ,et 1 (2)Spacer (2)3/;' x 3 3/4' Tubes BHCS w/Pin DETAIL TENDERDECKS Panel I I (4)3/;' Flange Nuts w/Pin (4) %" x 7/," BHCS w/Pin w/ 3L" SAE Flat Washers c�1 C-)� 1 C, I a M :a Q v cn 0 PlayBoosterl 115227 Zoo Panel Sheet 1 of 2 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328.8605 888-574-4678 LSI Install Help 888-438-6574 LEI Direct 763-972-5200 Int. FAX (763) 972-3185 J Document / 00 U v� landscape structures• Parts List Part# Description 124460 ABOVE DECK 105327 5" Half Clamp, Specify Color .......... 113729 Offset Hanger Clamp, Specify Color 113468 Spacer Tube, Specify Color ............... 140232 Zoo Panel, Specify Color ................... Qty 124900 Ttoderdeck Mounting Hardware Package......... 1 124460 3/4" x 3'/," BHCS w/Pin, SST .................................. 2 100196 %" x'/." BHCS w/Pin, SST ..................................... 4 100198 '/," x I Y." BHCS w/Pin, SST .................................. 4 100351 3/," Tee Nut, SST ........................................................ 4 100353 '/." Flange Nut w/Pin, SST ....................................... 6 100365 `/." SAE Flat Washer, SST ........................................ 4 Ill BELOW DECK 105327 5" Half Clamp, Specify Color .................................. 4 113729 Offset Hanger Clamp, Specify Color ....................... 4 113468 Spacer Tube, Specify Color ...................................... 2 113464 Angled Panel Bracket, Specify Color ...................... 1 140232 Zoo Panel, Specify Color .......................................... I 100610 1/4" x'/." Drive Rivet, AL/SST................................. 4 124947 Below Deck Mounting Hardware Package......... 1 124460 1/," x 3'/4" BHCS w/Pin, SST .................................. 2 100195 3/." x'/a" BHCS w/Pin, SST ..................................... 4 100198 %" x 1 Y." BHCS w/Pin, SST .................................. 8 100203 3/8" x 2 1/," BHCS w/Pin, SST .................................. 2 100351 '/," Tee Nut, SST ........................................................ 8 100353 1/a" Flange Nut w/Pin, SST ....................................... 6 Specifications Permalene' Panel: Solid color panel measures 35 %" wide x 41" high, color specified. Angled Panel Brkt: Weldment comprised of .190" thick 5052 aluminum formed angle with (2) 6061-T6 aluminum threaded tubes 1 Y." O.D. z I '/,"long. Finish: PmShiel&, color specified. Spacer Tube: Made from 6061-T6 aluminum'/," O.D. x 1 Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifieutions). Installation Time: Above Deck Approx. 3/, man hour Below Deck Approx. I man hour Weight: Above Deck 32 lbs. Below Deck 40 lbs. PlayBooster" 115227 Zoo Panel Installation Instructions ABOVE DECK (See Sheet I of 2) 1) Attach panel to the face of the deck, using'/s" x %" BHCS w/pin with'/," SAE flat washers and'/," flange nuts w/pin. See Detail. 2) Attach offset hanger clamp assemblies to posts at height shown, us- ing half clamps and 3/." x 1 Y." BHCS w/pin with 3/a" tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 3) Attach panel to offset hanger clamp assemblies using 3/." x 3 3/4" BHCS w/pin, spacer tubes and 3/," flange nuts w/pin. See Panel At- tachment Detail. 4) Install protective surfacing before users are allowed to play on the structure. BELOW DECK (See Sheet 2 of 2) I ) Attach offset hanger clamp assemblies to posts at height shown, us- ing half clamps and'/," x I '/," BHCS w/pin with 3/g" tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 2) Attach angled panel bracket to bottom of panel, using 3/,' x 3/,' BHCS w/pin and 3/." flange nuts w/pin. See Panel Attachment Detail. 3) Attach angled panel bracket with panel to offset hanger clamp as- semblies, using 3/,' x 2'/," BHCS w/pin. See Below Deck Mount. 4) Attach top of panel to offset hanger clamp assemblies, using 3/," x 3 3/," BHCS w/pin, spacer tubes and 3/." flange nuts w/pin. See Typical Attachment To Post Detail. 5) Install '/,"x%"drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 6) Install protective surfacing before users are allowed to play on the" structure. 1w ECO#51327�t#140237Wrtpl p13393 .Cwigepios. opmiVto 1'/.'dimelm. o_ C- `� C e" O -4 f") -G tI 47) =<rn Ill �r"S S O r� J A o ._j ECO#51327�t#140237Wrtpl p13393 .Cwigepios. opmiVto 1'/.'dimelm. 414, landscape structures° (2)'/a' Flange Nuts w/Pin i n ,-. of Clamp—e, (4)Typical Offset Hanger Clamp Assemblies i i (2)'/;' x 2'/;' BHCS w/Pin i i Protective Surfacing 0 2002 by LaWu W Sbuctums. NI rights reserved. I , v 48" or Higher - J Deck I (2)Spaoar T be I (2) °/e" x 3 BHCS w/Pin (4) %" x °/e' . BHCS w/Pin v _Ci - - Q --- 0 i 0 Angled Panel �_4(4)'/e" Flange Bracket Nuts w/Pin 115227 140237a0 �-,Typical PlayBooster Post i i i i I 0 Panel I i BELOW DECK MOUNT Sheet 2 of 2 Document #14023700 S & landscape structures, co Top O7' clamp A sop of SAFETY NOTE Naga a Oal Haight sValue O material mat rias a Cnt¢al Helght Velue of at lees) the 1, height of bre Highest Accessible laNFdll 'SO 14M® Carli led F11481gtMeQaceM erry�ipmerl. (Rd ASTM 15946100 DETAIL (6)3/," x 1'/;' PAN E L ATTAC H M E N T Limited Thread (2) °/;' x 33/." BHCS w/PF BRCS w/Pin /;\ &'' SAE Flat Washers (6)3/."Flange l/ 1 (6) Bell Nuts w/Pin-- Panel Strikers I I (2)'/;' Flange Nuts w/Pin (2) Spacer J Tubes (2)Typical Offset Hanger Clamp � Assemblies (6) Post Plates I &fTl Panel Dads <_--' (2) 5" Bob I , � t Front Of Panel DECK MOUNT ® 2007 by Landscape Structures All rights reseryed 0 �z,IIIfi1C�3��oDL�[b�� (4)a/;' Flar Nuts w/Pin 1 (2) 6" Bells 1 1 t 1 �T(2) 3" Bells o_ cn k..< oS l F TAIL M cn (4)'/;' x 7/11' BHCS w/Pin w/'/," SAE Flat Washers 159459 ITA 55328.8605 888-5744678 LSI Install Help 888-438-6574 LSI Direct 76"72-5200 Int. FAX (763) 972-3185 Document #15946100 (6) ,/;' x 1 '/B" BHCS w/Pin & 3/," SAE Flat Washers Typical PlayBooster Posts TOP.1 panel 1 1 I I I I I I Top O7' clamp A sop of SAFETY NOTE Naga a Oal Haight sValue O material mat rias a Cnt¢al Helght Velue of at lees) the 1, height of bre Highest Accessible laNFdll 'SO 14M® Carli led F11481gtMeQaceM erry�ipmerl. (Rd ASTM 15946100 DETAIL (6)3/," x 1'/;' PAN E L ATTAC H M E N T Limited Thread (2) °/;' x 33/." BHCS w/PF BRCS w/Pin /;\ &'' SAE Flat Washers (6)3/."Flange l/ 1 (6) Bell Nuts w/Pin-- Panel Strikers I I (2)'/;' Flange Nuts w/Pin (2) Spacer J Tubes (2)Typical Offset Hanger Clamp � Assemblies (6) Post Plates I &fTl Panel Dads <_--' (2) 5" Bob I , � t Front Of Panel DECK MOUNT ® 2007 by Landscape Structures All rights reseryed 0 �z,IIIfi1C�3��oDL�[b�� (4)a/;' Flar Nuts w/Pin 1 (2) 6" Bells 1 1 t 1 �T(2) 3" Bells o_ cn k..< oS l F TAIL M cn (4)'/;' x 7/11' BHCS w/Pin w/'/," SAE Flat Washers 159459 ITA 55328.8605 888-5744678 LSI Install Help 888-438-6574 LSI Direct 76"72-5200 Int. FAX (763) 972-3185 Document #15946100 t) landscape structures, Parks List PlayBooster" 159459 Ring -a -Bell Panel Part# Description Qty. ABOVE DECK 105327 5" Half Clamp, Specify Color .................................. 2 113729 Offset Hanger Clamp, Specify Color ....................... 2 113468 Spacer Tube, Specify Color ...................................... 2 158063 Bell Panel, Specify Color .......................................... 1 158318 Bell Striker, Specify Color ........................................ 6 158433 3" Bell, Specify Color ............................................... 2 158434 5" Bell, Specify Color...... ................. 2 158435 6" Bell, Specify Color .............................................. 2 100610 3/4" x 5/s" Drive Rivet, AL/SST................................. 2 159468 Bell Panel Hardware Package ............................... 1 100198 34" x 1'/," BHCS w/Pin, SST .................................. 6 100292 '/," x 1 1/4" BHCS w/Pin Limited Thread, SST ...... 6 100353 '/a" Flange Nut w/Pin, SST ....................................... 6 100365 '/s" SAE Flat Washers, SST ._ ..... ._____ ...................... 12 158335 Post Plate, SST........................................................... 6 124900 Tenderdeck Mounting Hardware Package......... 1 124460 3/s" x 3 3/4" BHCS w/Pin, SST .................................. 2 100196 '/i x'/," BHCS w/Pin, SST ..................................... 4 100198 3/8* x 1 '/s* BHCS w/Pin, SST .................................. 4 100351 Y." Tee Nut,SST........................................................ 4 100353 3/8" Flange Nut w/Pin, SST ....................................... 6 100365 3/s" SAE Flat Washer, SST ........................................ 4 BELOW DECK 105327 5" Half Clamp, Specify Color .................................. 4 113729 Offset Hanger Clamp, Specify Color ....................... 4 113468 Spacer Tube, Specify Color ...................................... 2 113464 Angled Panel Bracket, Specify Color ...................... 1 158063 Bell Panel, Specify Color .......................................... 1 158318 Bell Striker, Specify Color ........................................ 6 158433 3" Bell, Specify Color ............................................... 2 158434 5" Bell, Specify Color ............................................... 2 158435 6" Bell, Specify Color ............................................... 2 100610 'Q" x %" Drive Rivet, AL/SST................. I............... 4 159468 Bell Panel Hardware Package ............................... 1 100198 %" x I Y." BHCS w/Pin, SST .................................. 6 100292 3/3" x I '/." BHCS w/Pin Limited Thread, SST ...... 6 100353 3/8" Flange Nut w/Pin, SST ....................................... 6 100365 34" SAE Flat Washers, SST ..................................... 12 158335 Post Plate, SST........................................................... 6 124947 Below Deck Mounting Hardware Package......... 1 124460 3/r" x 3'/4" BHCS w/Pin, SST .................................. 2 100195 '/s" x 5/," BHCS w/Pin, SST ..................................... 4 100198 Y. x 13/, BHCS w/Pin, SST... ............................... 8 100203 5/8" x 2 3/4" BHCS w/Pin, SST .................................. 2 100351 '/i Tee Nut, SST ........................................................ 8 100353 %" Flange Nut w/Pin, SST ....................................... 6 Specifications Permalene' Panel: Two color panel measures 35 %" wide x 41" high, color specified. BeIlStriker. Two color Permalene, color specified. Betts: Fabricated from 10 GA. (.135") HRPO low carbon steel. Finish: ProShield', color specified. Angled Panel Brkt: Weldmenl comprised of .190" thick 5052 aluminum formed angle with (2) 6061-T6 aluminum threaded tubes I '/," O.D. x 1 '/s" long. Finish: ProShield, color specified. Spacer Tube: Made from 6061-T6 aluminum'/s" O.D. x 1 "/is". Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Above Deck Approx. 3/4 man hour Below Deck Approx. 1 man hour Weight: Above Deck 53 lbs. Below Deck 59 lbs. Installation Instructions ABOVE DECK (See Sheet I of 2) 1) Attach bell strikers to bell panel, using Y." x I '/," limited thread BHCS w/pin with 3/g' SAE flat washers and 3/s" flange nuts w/pin, as shown. 2) Insertpost plates into bell panel cutouts. Attach bells to bell Panel, using /," x 1 '/," BHCS w/pin and SAE flat washers, as shown. 3) Attach panel to the face of the deck, using s/g" x'/r" BHCS w/pin with 3/," SAE flat washers and 3/," flange nuts w/pin. See Detail. 4) Attach offset hanger clamps to posts at height shown, using 5" half clamps and %" x 1 3/s" BHCS w/pin with'/.' tee nuts. Refer To The Typical Offset Hanger Clamp Assembly Sheet. 5) Attach panel to offset hanger assemblies, using '/,"x3'/4"BHCS w/pin, spacer tubes and %" flange nuts w/pin. See Panel Attachment Detail. 6) Install protective surfacing before users are allosiN to play on the structure. O tin O BELOW DECK (See Sheet 2 of 2) 1) Attach bell strikers to bell panel, using usiog3�" x 1 tM limit thread BHCS w/pin with 3/," SAE flat washers 9}Rt ��e- flange nuts wyirk as shown. —c m $. ��� 1I 2) Insert post plates into bell panel cutouts t h b to be el, using /r" x 1 '/r" BHCS w/pin and 3/," S 11II3t w rs, as sl—sown. 3) Attach offset hanger clamps to posts at Haight show using 5" half clamps and'/," x 1 '/," BHCS w/pin with%" tee nuis?Refer To The Typical Offset Hanger Clamp Assembly Sheet. 4) Attach angled panel bracket to bottom of panel, using '/e " x %" BHCS w/pin and'/," flange nuts w/pin. See Below Deck Mount. 5) Attach angled panel bracket with panel to offset hanger clamp as- semblies, using 5/," x 2 1/4" BHCS w/pin. See Below Deck Mount. 6) Attach top of panel to offset hanger clamp assemblies, usu . no 3/r" x 3'/4" BHCS w/pin, spacer tubes and 3/," flange nuts w/pin. See Typical Attachment To Post Detail. 7) Install'/4" x %" drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Assembly sheet. 8) Install protective surfacing before users are allowed to play on the structure. U landscape structures (2) 4/a. Nuts v x (4) Typical Offset Hanger Clamp Assemblies I I I I i I I (2) S/p' x 2 1/4- BHCS w/Pin II of (6)'/e' x 1 1/ Limited BHCS w & 3/e" SA Washers 1 i BHCS w/Pin & a/e' SAE Flat Washers I I ! (2) Spacer (2) °/e " x 3 a/. BHCS w/Pin x 4/e w/Pin il t I � i i i t'a LY I , I , I , I , I ' Angled Panel Bracket Protective Surfacing SWctures. All rights reserved. E 159459 Ri i' Thread Flat /Pin i 56" or Higher Deck " (6) Bell Strikers O (2) 5" Bell 3/," Flange is w/Pin 159461a Typical PlayBooster Post i i i i I I i I i (6)'/;' Flange Nuts w/Pin O (6) Post Plates (2) 6" Bells Bell Panel (2) 3" Bells o � N o I ,0 (. rn BELOW—t-: DECK = MOUNT crt -Bell Panel Sheet 2 of 2 Document#15946100 SAFETY NOTE CM1M58 a prolective auRatillg malenal that nas a Cnticai Maignl Value of a1 least the ISO V{7 1400i , 1111hMi/ aignl of M Mipnest A¢ersiEle Pa all {/ � I I Hegntcltlie aQa�nteWpment (Rat.ASTM landscapeCertified PodB].) structurest66°99°° ° DETAIL BONGO ATTACHMENT a/;' x'/;' BHCS w/Pln (ts)•/; rlange -- 'o' SAE Flat Washers 35 `)i Nuts w/Pin Typical Lame PlayBooster BongoBongo Post Small Panel Bongo Top of Panel Bongo (2) Bongos Top of Panel clamp DETAIL PANELATTACHMENT (2)Typical Offset Hanger Clamp Assemblies 0 (2)'/," x 3 a/; BHCS w/Pin Bongo Panel (2) Screen Deck Plates 2 Spacer Top 01 Tubes (2)3/;' Flange peck \ Nuts w/Pin DETAIL Rack Side Of Panel TENDERDECKS DECK MOUNT Panel® (4)'/a" Nuts v :€ 4155— 155-- (4 (413"x x ]/e CS w/Pin c')"S wj'/a" SAZUbt Washers —f n rn �— :<I— n _a C! t� Sheet 1 of 2 (::;Sheet ® 2009 by Landscape Structures All nghts feserved Document #16609900 'M landscape structures• J'.ISPECS iMi6w"01M Parts List PlayBooster" 164092 Bongo Panel® Clamps: Cast aluminum. Finish: PmShield, color specified. Specifications Bongo Panel: Two color Permalene` panel measures 35 3/," wide x 41" high, color specified Bongo: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Angled Panel Britt: Weldmew comprised of .190" thick 5052 aluminum formed angle with (2) 6061-T6 aluminum threaded tubes I '/," O.D. x I'/," long. Finish: PmShield4, color specified. Screen Plate: Fabricated from 12 GA. (.105") HRPO flat steel. Fin- ish: P1oShield, black in color. Spacer Tube: Made from 6061-T6 aluminum'/," O.D. x 1 Finish: ProShield, color specified. 3) Attach offset hanger clamp assemblies to posts at height shown, us- ing half clamps and'/," x 1 '/," BHCS w/pin with'/," tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 4) Attach angled panel bracket to bottom of panel, using'/." x'/." BHCS w/pin and'/." flange nuts w/pin. See Below Deck Mount. 5) Attach angled panel bracket with panel to offset hanger clamp as- semblies, using'/," x 2 '/," BHCS w/pin. See Below Deck Mount. 6) Attach top of panel to offset hanger clamp assemblies, using'/," x 3'/." BHCS w/pin, spacer tubes and 3/," flange nuts w/pin. See Below Deck Mount. 7) Install'/," x'/," drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 8 Install protective surfacing before users are allowed to play on the structure. Ew #537] I nuiamem 1n6a9900 nyWes 164e9600. Added uran Pim w Paea Liv. Fasteners: Primary fasteners shall be socketed and pinned Pert# Description tion t Qty. tamperproof in design, stainless steel (SST) per ASTM ABOVE DECK F 879 unless otherwise indicated (see specific prod - 105327 -01 5" Half Clamp, Specify Color ..............................._ - 2 net installation/specifications). 113729-00 Offset Hanger Clamp, Specify Color ....................... 2 113468-00 Spacer Tube, Specify Color ...................................... 2 Installation Time: Above Deck Approx. 1 man how 164128-00 Bongo Panel, Specify Color ...................................... I Below Deck Approx. I Y. now boors 163911-00 Small Bongo, Specify Color ..................................... l Weight: Above Deck 53 lbs. 163912-00 Large Bongo, Specify Color ..................................... I Below Deck 59 lbs. 164523-00 Screen Plate, Black .................................................... 2 164415-00 Bongo Panel Hardware Package .......................... 1 100196-00 3/," x'/," BHCS w/Pin, SST ..................................... 8 Installation Instructions 100353-00 '/." Flange Nut w/Pin, SST ....................................... 8 100365-00 '/," SAE Flat Washer, SST ........................................ 8 162374.00 '/," x'/," BHCS w/Pin, SST ..................................... 6 ABOVE DECK (See Sheet 1 of 2) 127463-00 T-27 Hex Bit............................................................... 1 1) Attach screen plates to bongos, using'/," x'/4" BHCS w/pin. Refer 124900-00 Tenderdeck Mounting Hardware Package ......... 1 to the Screen Attachment Detail. NOTE: Screen plates attach (flat 124460-00 /e" x 3 /," BHCS w/Pin, SST .................................. 2 side to flat side) to inside of Bongos. 100196-00 Y." x 14" BHCS w/Pin, SST ..................................... 4 100198-00 '/," x 1 '/." BHCS w/Pin, SST .................................. 4 2) Attach Bongos to Bongo Panel using 3/e" x'/," BHCS w/pin with'/," 100351.00/," Tee Nut, SST ........................................................ 4 SAE Bat washers and'/," flange nuts w/pin. Refer to the Bongo At - 100353 -00 /," Flange Nut w/Pin, SST ....................................... 6 tachment Detail. 100365-00 3/," SAE Flat Washer, SST ........................................ 4 BELOW DECK 3) Attach panel to the face of the deck using'/," x'/," BHCS w/pin with 105327-01 5" Half Clamp, Specify Color .................................. 4 3/,^ SAE Hat washers and '/," flange nuts w/pin. Refer to the 113729-00 Offset Hanger Clamp, Specify Color ....................... 4 Tenderdeck Detail. 113468-00 Spacer Tube, Specify Color ...................................... 2 164128-00 Bongo Panel, Specify Color. 1 4) Attach offset hanger clamp assemblies to posts at height shown, us - 163911 -00 Small Bongo, Specify Color ..................................... 1 ing half clamps and'/," x I '/," BHCS w/pin with'/," tee nuts. Refer 163912-00 Large Bongo, Specify Color ..................................... 1 To The Typical Offset Hanger Clamp Spec Sheet. 113464-00 Angled Panel Bracket, Specify Color ...................... 1 100610-00 '/," x'/a" Drive Rivet,AL/SST................................. 4 5) Attach panel to offset hanger clamp assemblies, using'/," x 3'/," 164523-00 Screen Plate. Black .......................... 2 BHCS w/pin, spacer tubes and'/," flange nuts w/pin. Refer to the 164415-00 Bongo Panel Hardware Package .......................... 1 Panel Attachment Detail. r.a 100196-00 3/," x'/," BHCS w/Pin, SST ..................................... 8 r� 100353-00 '/e" Flange Nut w/Pin, SST ....................................... B 6) Install protective surfacing before usetFre allowell to play on the 100365-00 '/," SAE Flat Washer, SST ........................................ 8 structure. C'S C= 162374-00 1/4" x 3/4' BHCS w/Pin, SST ..................................... 6'�--- n Y _j -4 127463-00 T-27 Hex Bit............................................................... 1 BELOW DECK (See Sheet 2 of 2) n--< I 124947-00 124460-00 Below Deck Mounting Hardware Package......... Y." 3'/," BHCS SST 1 2 1) Attach screen plates to bongos, using'� l'fy' BfPS w/p for 100195-00 x w/Pin, .... ....................... '/," x'/," BHCS w/Pin, SST ..................................... 4 to the Screen Attachment Detail. NOTEttl n p*rs att2Mtdin- 100198-00 '/," x 1 '/,^ BRCS w/Pin, SST .................................. 8 side of Bongos. — -= G '� 100203-00 100351-00 '/," x 2 '/4" BHCS w/Pin, SST .................................. '/," Tee Nut, SST 2 8 2) Attach Bongos to Bongo Panel using'/." 3eJJ�'rbHRw/pin with 3/." 100353-00 ........................................................ '/," Flange Nut w/Pin, SST ....................................... 6 SAE flat washers and %" flange nuts w/Ar. Referehe Bongo At- tachment Detail. Specifications Bongo Panel: Two color Permalene` panel measures 35 3/," wide x 41" high, color specified Bongo: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Angled Panel Britt: Weldmew comprised of .190" thick 5052 aluminum formed angle with (2) 6061-T6 aluminum threaded tubes I '/," O.D. x I'/," long. Finish: PmShield4, color specified. Screen Plate: Fabricated from 12 GA. (.105") HRPO flat steel. Fin- ish: P1oShield, black in color. Spacer Tube: Made from 6061-T6 aluminum'/," O.D. x 1 Finish: ProShield, color specified. 3) Attach offset hanger clamp assemblies to posts at height shown, us- ing half clamps and'/," x 1 '/," BHCS w/pin with'/," tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 4) Attach angled panel bracket to bottom of panel, using'/." x'/." BHCS w/pin and'/." flange nuts w/pin. See Below Deck Mount. 5) Attach angled panel bracket with panel to offset hanger clamp as- semblies, using'/," x 2 '/," BHCS w/pin. See Below Deck Mount. 6) Attach top of panel to offset hanger clamp assemblies, using'/," x 3'/." BHCS w/pin, spacer tubes and 3/," flange nuts w/pin. See Below Deck Mount. 7) Install'/," x'/," drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 8 Install protective surfacing before users are allowed to play on the structure. Ew #537] I nuiamem 1n6a9900 nyWes 164e9600. Added uran Pim w Paea Liv. U� landscape structures (8)3/e" Flange DETAIL Nuts w/Pin, SCREEN ATTACHMENT .(2) Bongos 2 Screen Plates ' BHCS w/Pin (2)'/;' Flange Nuts w/Pini Top of Cts (4)Typigecal Offset Hanr Clamp Assemblies i i 0 M (2)5/a x2'4 BHCS w i i of DETAIL BONGO ATTACHMENT (8)'/d' x'/e" BHCS w/Pln li'/;' SAE Flat Washers : Screenattach (flat (2) Bongos flat side) to M Bongo of Bongos. Panel 48" or Higher --------__- Deck - --" ------- ------Large — _-------- Small Bongo --------- Bongo (2) Spacer (2) 31," x 3 a/a BHCS w/Pin x'/: w/Pin 40 pinished Grade =' ProtectiV- Surfacing Angled Panel Bracket ® 2009 by LandsL pe 9ruMms. All nght reserved. 7 t) 166099a }/Typical PlayBooster Post Bongo (2) Screen Plates 0 C7 < 1 �� ^i C^! Cn 1)3/e" Flange c� uts w/Pin *—'DECK ' MOUNT 164092 Bonqo Panel® Sheet 2 of 2 sl/& landscape structuress DETAIL SADDLE SPINNER SEAT ASSEMBLY Shaft Assembly - NOTE: Install Rubber Gasket with small diam- eter down. DETAIL DIRECT BURY Saddle Seat Shaft Assembly Loose Fill p'r�tya,r' live Surface ;t ati Ili= Subgradel l l 11- -111 Concrete nmw whin IN/ a/s' SAE Flat Washers C N OWN ISO 14001 Protective facing SAFETY NOTE chodee a protxvrve unea g material mat has a Critical Height Value of at least the height o/ the Highest Accesside ParVFall Height of the adjacent equipment (Ref ASTM F1487) 20078700 DETAIL MINIMUM USE ZONE f t I Saddle Spinner 1 (4,17 m) i Saddle Spinner —Play Safe Label Warning Label SECTION SURFACE MOUNT (4)1/,' Standard Hex Nuts w/'/,' Flat Washers (4)1/2" x z a/ Expansion Anchors Concrete Crushed Rock Rock r D. r• Kids a •152179 Saddle Spinner 601 7TH STREET SOUTH, DELANO.. MINNESOTA 55728-8605 8BB-5744578 LSI Install Help 888-438-6574 / Saddle 1.' Spinner -`a NCdTE: Si�Wiclent protec- tive surfacing must cover hardware to satisfy fall height requirements. A& landscape structures* Parts List Kids In Motion 152179 Saddle Spinner Part # Description Qty. 151539 Saddle Spinner Seat, Specify Color..__..... _....1 197017 Shaft Assy., DB, Specify Color ........ ....... ... ....... e 197018 Shaft Assy. 12" Seat Height, SM, Specify Color..... _.... 197011 Shaft Assy. 16" Seat Height, SM, Specify Color........... • 211418 Spinner Seat Hardware Package ..............................1 100196 '/," x 7/," BHCS w/Pin, SST..........................................4 100365 3/i SAE Flat Washer, SST.............................................4 156845 Play Safe Label, 2-5 Yrs ................................................ l 156847 Play Safe Istel, 5-12 Yes..............................................1 127935 '/le" x 2 "/y" Rubber Gasket. .........................................1 183064 Warning label...... ........ .................................................. l 121348 4 -Hole (SM) Hardware Package .............................. 1 100266 '/.' x 2'/4" Expansion Anchor.......................................4 100322 '/;" Standard Hex Nut, SST...........................................4 100363 '/2" Flat Washer, SST.....................................................4 • - Quantity Determined By Your Order DB - Direct Bury SM - Surface Mount Specifications Shaft Assent bly: (Saddle Spinner Seat Post) Weldment comprised of 2.875" O.D. RS40 (.160"-.170" Wall) galvanized steel tubing, 1.250" O.D. steel shaft, 12 Ga. (.105") HR flat steel, and 1144 steel collar. Finish: Pro - Shield`, color specified. (Sleeve/Plate) Weldment comprised of/," sheet HRPO steel and 2.875" O.D. schedule 80 steel tubing. Finish: ProShield, color specified. Rubber Casket: Made from 50 durometer neoprene. Saddle Spinner Seat: Rotationally molded from U.V. stabilized linear low density polyethylene measuring 18'/," wide x 7" high, color specified. Fasteners: Primary fasteners shal I be socketed and pinned tam- perpmof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific product installation/specifications). Installation Time: I man hour (DB) Installation I) (Direct Bur)) Dig footing as shown. Refer to the Direct Bury Detail. 2) Attach saddle spinner seat and rubber gasket to shaft assembly using '/a" x'/," BHCS w/pin and'/," SAE flat washers. Refer to the Saddle Spinner Seat Attachment Detail. NOTE: Install Rubber Gasket with small diameter down. 3) (Direct Bury) Place the shaft assembly in footing hole. Place a levelon the shaft assembly gusset, when gusset is plumb pour concrete footing. Allow concrete footing to cure a minimum of 72 hours before users are allowed to play on structure. NOTE: Saddle spinner will have to be propped in position, until concrete has cured (Surface Mount) Drill 1/2" x 3" deep holes through base plate using hammer drill and'/2" masonry bit. Tap expansion anchors into drilled holes. Attach shaft assembly base plate to expansion anchors using 1/2" standard hex nuts with 1/2" flat washers. 4) If required to meet Canadian Standard (CSA Z614) requirement for water ponding, drill (3) 4;' diameter drain holes on top side of seat, and (3)'/," diameter holes on bottom side ofseat. NOTE: Positions are prelocated on both sides of seat with an indent marking. Use caution to drill through one wall ojplastic onh•. 5) Apply labels as shown. 6) Install protective surfacing before users are allowed to play on the structure. s O O Eme010038913o,v 1#211419 mple 420182800 RWlauh dw pwkage. �r t M 0 '/, man hour (SM) Weight: 36 His. (DB) 30 lbs. 12" Seat Height (SM) 32 His. 16" Seat Height (SM) Area Req.: 13'8" (4,17 m) diameter Min. Use Zone.: 6 (1,83 m) Concrete: Approx. 3 '/2 cu. ft. (DB) Fall Height: 12" (300 mm) 2-5 Years 16" (410 mm) 5-12 Years Installation I) (Direct Bur)) Dig footing as shown. Refer to the Direct Bury Detail. 2) Attach saddle spinner seat and rubber gasket to shaft assembly using '/a" x'/," BHCS w/pin and'/," SAE flat washers. Refer to the Saddle Spinner Seat Attachment Detail. NOTE: Install Rubber Gasket with small diameter down. 3) (Direct Bury) Place the shaft assembly in footing hole. Place a levelon the shaft assembly gusset, when gusset is plumb pour concrete footing. Allow concrete footing to cure a minimum of 72 hours before users are allowed to play on structure. NOTE: Saddle spinner will have to be propped in position, until concrete has cured (Surface Mount) Drill 1/2" x 3" deep holes through base plate using hammer drill and'/2" masonry bit. Tap expansion anchors into drilled holes. Attach shaft assembly base plate to expansion anchors using 1/2" standard hex nuts with 1/2" flat washers. 4) If required to meet Canadian Standard (CSA Z614) requirement for water ponding, drill (3) 4;' diameter drain holes on top side of seat, and (3)'/," diameter holes on bottom side ofseat. NOTE: Positions are prelocated on both sides of seat with an indent marking. Use caution to drill through one wall ojplastic onh•. 5) Apply labels as shown. 6) Install protective surfacing before users are allowed to play on the structure. s O O Eme010038913o,v 1#211419 mple 420182800 RWlauh dw pwkage. �r t M 0 a& _ y landscape structures° S R 9.4PETV NOTE Gwose a protaM. sixf., material that �/� r� /�/� has a Cristal Haigtt Value of at lele P8 as)the Is014001 , Hfghtoltheals,enlight of the sepuipmanl(Ref $TM Cer11'led F1487) 18563300 PLAN VIEW Single Bobble Rider I NOTE: Sufficient protec- tive surfacing must cover Seat hardware to satisfy fall height requirements. (4)1/2' Standard Hex Nuts w/ 1/2" Flat Washers Top of Anchor '14" -?/S" 19-22 — BHCS (4)'/2' x 6"� Flat Anchor Bolts 12" Flat Washers 12" Hex Patch Nuts /z' Hex Jam Nuts DETAIL SURFACE MOUNT c .e Concrete Slab Sheet 1 of 2 0 2012 by Landscape Swctures Au nghts reserved Document #18563300 o \ Crushed C1 n Roa I __1 e n -G r m IT a M �� tD (n Sheet 1 of 2 0 2012 by Landscape Swctures Au nghts reserved Document #18563300 W, Kids In Motion 164074 Bobble Rider", Single landscape structures` Parts List Installation Instructions Part# Description Qty - 115154 -00 Leg, (DB), Black ........................................................ 1 132276-00 Spring Assembly, Black ............................................ 1 160586-00 Seat, Black.................................................................. 1 185342-00 Single Bobble Rider, Specify Color ........................ 1 183806-00 Single Bobble Rider Hardware Package ............. 1 100196-00 Y," x'/," BHCS w/Pin, SST ..................................... 4 100362-00 '/," Flat Washer, SST ................................................. 4 100363-00 '/2" Flat Washer, SST ................................................. 2 129692.00 '/," Hex Patch Nut, SST ............................................ 2 129693-00 1/2" Hex Jam Nut, SST ............................................... 2 156846-00 Play Safe Label 2-12 Years ....................................... 1 183064-00 Warning Label............................................................ 1 115326-00 Spring Rider (DB) Hardware Package ................ 1 100198-00 Y," x 1 14" BHCS w/Pin, SST .................................. 4 100327-00 '/," Standard Hex Nut, SST ...................................... 4 100365-00 '/," SAE Flat Washer, SST ........................................ 8 110102-00 Spring Animal Anchor Hardware Package (SM)l 100262-00 1/2" x 6" Anchor Bolt .................................................. 4 100322-00 '/2" Standard Hex Nut, SST ...................................... 4 100363-00 '/2" Flat Washer, SST ................................................. 4 DB - Direct Bury SM - Surface Mount Specifications Bobble Rider: Weldment comprised of 1.315" O.D. RS20 (.080"- .090" wall) galvanized steel tubing, 2.375" O.D. RS20 Installation Time: (.095"-.105" wall) galvanized steel tubing,'/," HRPO steel plate, '/4" HRPO steel plate, and 4" diameter 10 Concrete Req.: GA. (.135") low carbon steel ball. Finish: ProShielda, Area Req.: color specified. Spring: Weldmentcomprised of5'/,"diameter °/16"tempered alloy steel coil. Finish: ProShield, black in color. Seat: Rotationally molded from U.V. stabilized linear low density polyethylene, black in color. Leg: Weldment comprised of 3.500" O.D. RS20 (.120" - .130" wall) galvanized steel tubing and 1/4" x 10" di- ameter HRPO zinc plated steel. Finish: ProShield, black in color. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM (Direct Bury) 1) Dig footing hole as shown. 2) Attach Bobble Rider to spring assembly using'!," Bat washers,'/," hex patch nuts and Y." hex jam nuts, as shown. 3) Attach spring assembly to footer using'/," x 1 '/," BHCS w/pin with SAE Bat washers and'/," standard hex nuts with Y." SAE Bat wash- ers. 4) Attach seat to Bobble Rider [sing'/," x Y," BHCS w/pin and Y." flat washers. 5) With footer plumb and Bobble Rider propped up, pour concrete ftot- ing and let core for a minimum of 72 hours before using. 6) Apply labels as shown. 7) Install protective surfacing before users are allowed to play on the component. (Surface Mounting On A Concrete Slab) 1) Using the spring assembly base plate as a pattern, make a plywood template for anchor bolt placement. Attach'/," x 6" anchor bolts with Y2" standard hex nuts and'/," flat washers to holes in template. 2) Pour concrete slab and lay template on surface in level position. Push '/," x 6" anchor bolts into concrete and allow 3/4" to %" of thread to protrude from concrete. Allow 72 hours before template removal. 3) Attach spring assembly base plate to anchor bolts in concrete with '/2" standard hex nuts and'/," flat washers. 4) Attach Bobble Rider to spring assembly using '/," flat washers,'/," hex patch nuts and'/," hex jam nuts, as shown. 5) Attach seat to Bobble Rider using'/," x'/," BHCS w/pin and'/," flat washers. 6) Apply labels as shown. 7) Sufrcienl protective surfacing for a 2' fall height should cover bot- tom plate and anchor bolts. (See ASTM F1487, Section 9.) c:) Cn F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: SM- Approx. l'/, man hours DB - Approx. 2 man hours Concrete Req.: DB -Approx. 3 cu. R Area Req.: 14'-%" x 13'-6" (4,27 m x4,11 m) minimum use zone Weight: (SM) 61 lbs (DB) 77 lbs Seat Height: 20'/6" (530 mm) (Direct Bury) 1) Dig footing hole as shown. 2) Attach Bobble Rider to spring assembly using'!," Bat washers,'/," hex patch nuts and Y." hex jam nuts, as shown. 3) Attach spring assembly to footer using'/," x 1 '/," BHCS w/pin with SAE Bat washers and'/," standard hex nuts with Y." SAE Bat wash- ers. 4) Attach seat to Bobble Rider [sing'/," x Y," BHCS w/pin and Y." flat washers. 5) With footer plumb and Bobble Rider propped up, pour concrete ftot- ing and let core for a minimum of 72 hours before using. 6) Apply labels as shown. 7) Install protective surfacing before users are allowed to play on the component. (Surface Mounting On A Concrete Slab) 1) Using the spring assembly base plate as a pattern, make a plywood template for anchor bolt placement. Attach'/," x 6" anchor bolts with Y2" standard hex nuts and'/," flat washers to holes in template. 2) Pour concrete slab and lay template on surface in level position. Push '/," x 6" anchor bolts into concrete and allow 3/4" to %" of thread to protrude from concrete. Allow 72 hours before template removal. 3) Attach spring assembly base plate to anchor bolts in concrete with '/2" standard hex nuts and'/," flat washers. 4) Attach Bobble Rider to spring assembly using '/," flat washers,'/," hex patch nuts and'/," hex jam nuts, as shown. 5) Attach seat to Bobble Rider using'/," x'/," BHCS w/pin and'/," flat washers. 6) Apply labels as shown. 7) Sufrcienl protective surfacing for a 2' fall height should cover bot- tom plate and anchor bolts. (See ASTM F1487, Section 9.) c:) Cn �^ O C 1 ox O D y O J Eco #54W Grum t#18%3200 telxcn#183837110. Rc ipMb Wle rifer. IV & landscape structures' (4) a/e' X I '/a BHCS w/Pin w/ '/," SAE Flat Washers (4)'/a' Standard Hex Nuts w/'/," SAE Flat Washers Kids In Motion DETAIL _— Spring Assembly DETAIL DIRECT BURY Leg Spring i Assembly Loose Fill'T - Protective Surfacing Leg Crushed Rock 164074 SAFETY NOTE Choose a protective soman, mabA'tal ptel has a Cnbeel Heighl Value of et least Ne heiBnl of the Highest Accessible PaNFall Hephlalthe eQacentepapment.(Re ... Fuer i 164076a Sinale Sheet 2 of 2 L 2012 by Landscape Structures All rights reserved Document # 18563300 N O g c-) Cr r <t�,t a M —v 0 �z D cn Sinale Sheet 2 of 2 L 2012 by Landscape Structures All rights reserved Document # 18563300 IS& landscape structures® Warning Label - (4) 1/1° x 2 t/4"— Flat Head Cap Screws (2) Spring/Wedge Assemblies iD Spring Bottom Plate 1 I 1 C E P.TIF IE 0 Double Bobble Rider Play Safe Label Seats (8) Ya" x r/e i BHCS w/Pin & 34" Flat Washers (4)'/1 Flat Washers (4) 1/2" Hex Patch Nuts (4) 1/2' Hex Jam Nuts —(4)1/2" Hex Jam Nuts '(4) 1/i' Hex Patch Nuts �(4) 1/2" Flat Washers e (4) 1/2, x 2 t/ Flat Head Cap Screws SAFETY NOTE Choose a IxWecave surfating ins iel that has a CHtical Height Value of al least the height of the Highest Amessible Pa F811 Height ofthe eQacent equipment. (Ref ASTM F148T) 18563400 PLAN VIEW �,,, n } 24 3/a:'':.`.r tE 3 tT M ISI Gr'n a 1 AAn7r% Rnhhln RirinrT" n^ykio Finished Grade • • • - — - - - - - - - - J IM1111111111126Z 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888.5744678 LSI Install Help 888-438-6574 LSI Direct 763-972.52 =0 Int. FAX (763) 972.3185 • - Ian a -s *E1946 .11 Parts List Kids In Motion 164075 Bobble RiderTM11, Double Part# Description Qty. 132912-00 Spring/Wedge Assembly, Black ................................ 2 160586-00 Scat, Black.................................................................. 2 185341-00 Double Bobble Rider, Specify Color ....................... 1 164058-00 Footer (DB), Black .................................................... 1 164318-00 Spring Bottom Plate (SM), Black ............................ I 183887-00 Double Bobble Rider Hardware Package........... 1 100196-00 Ys" x r/4" BHCS w/Pin, SST ..................................... 8 100362-00 r/," Flat Washer, SST ................................................. 8 100363-00 '/z" Flat Washer, SST ................................................. 8 129692-00 '/2" Hex Patch Nut, SST ............................................ 8 129693-00 '/," Hex Jam Nut, SST ............................................... 8 130824-00 '/." x 2 '/4" Flat Head Cap Screw, SST .................... 8 156846-00 Play Safe Label 2-12 Years ....................................... 1 183064-00 Warning Label............................................................ 1 121868-00 Spring Animal Anchor Hardware Package (SM)1 100262-00 %" x 6" Anchor Bolt .................................................. 6 100322-00 1/2" Standard Hex Nut, SST ...................................... 6 100363-00/i' Flat Washer, SST ................................................. 6 DB - Direct Bury SM = Surface Mount Specifications Double Bobble Rider: Weldment comprised of 1.315" O.D. RS20 (.080"- .090" wall) galvanized steel tubing, 2.375" O.D. RS20 (.095"-.105" wall) galvanized steel tubing,'/s" HRPO steel plate, '/4" HRPO steel plate, and 4" diameter 10 GA. (.135") low carbon steel ball. Finish: ProShielda, color specified. Spring: Weldment comprised of 5'/8" diameter 11/16" tempered alloy steel coil. Finish: ProShield, black in color. Seat: Rotationally molded from U.V. stabilized linear low density polyethylene, black in color. Spring Bottom Plate: Fabricated from'/s" x 10" x 17" sheet HRPO steel. Finish: ProShield, black in color. Footer: Wekhnentcomprisedof3'/,"O.D.RS20(.120"-.130" wall) galvanized steel tubing and 1/4" x 10" x 17" sheet HRPO steel. Finish: ProShield black in color. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- o� uct installation/specifications). Installation Time: SM - Approx. 2 man hours O DB - Approx. 2'/4 man hours Concrete Req.: DB - Approx. 5.25 cu. ft. Area Req.: IS' -2 n/.6' x 13'-6" (4,64 in x 4,11 m) Minimum Use Zone Weight: (SM) 113 lbs (DB) 13716s Seat Height: 201/4" (527 mm) Installation Instructions (Direct Bury) 1) Dig footing hole as shown. 2) Attach Bobble Rider to spring/wedge assemblies using'/," x 21/4" flat head cap screws, 'I," flat washers, '12" hex patch nuts and 1/2" hex jam nuts, as shown. 3) Attach spring/wedge assemblies to footer wing 1/2" x 2'/4' flat head cap screws,'/," flat washers,'/," hex patch nuts and 1/2" hex jam nuts. 4) Attach seats to Bobble Rider using 3/," x Y." BHCS w/pin and'/s" flat washers. 5) With footer plumb and Bobble Rider propped up, pour concrete foot- ing and let cure for a minimum of 72 hours before using. 6) Apply labels as shown. 7) Install protective surfacing before users are allowed to play on the component. (Surface Mounting On A Concrete Slab) 1) Using the spring bottom plate as a pattern, make a plywood template for anchor bolt placement. Attach 'A" x 6" anchor bolts with'/2" stan- dard hex nuts and'/2" flat washers to holes in template. 2) Poor concrete slab and lay template on surface in level position. Push '/z' x 6" anchor bolts into concrete and allow Y." to %" of thread to protrude from concrete. Allow 72 hours before template removal. 3) Attach spring/wedge assemblies to spring bottom plate wing 1/2" x 21/4" flat head cap screws, 1/2" flat washers, '/2" hex patch nuts and '/2" hex jam nuts. 4) Attach spring bottom plate to anchor bolts in concrete with '/2" stan- dard hex nuts and '/z" flat washers. 5) Attach Bobble Rider to spring/wedge assemblies using'/2" x 2'/d' flat head cap screws,'/," flat washers, '/," hex patch nuts and '/2" hexjam nuts, as shown. 6) Attach seats to Bobble Rider using'/f' x %" BHCS w/pin and 3/s" flat washers. 7) Apply labels as shown. 8) Suficient protective surfacing for a 2' fall height should cover bot- tom plate and anchor bolts. (See ASTM F1487, Segiign 9.) _ o O �^ C-3 _< =;c-)� r M o� Z O v 1W#54588 noc,mret #18563400 ,ep1e 418383800. Redraipn txftk rider. V _ landscape structures° (2) Ass (2) SpringN Assemblies Loose FIII - Protective - _ Surfacing I 1 � bgrade Footer x_47 , Concrete d ' O Rock DETAIL DIRECT BURY BASE LEG ATTACHMENT DETAIL DIRECT BURY Screws SAFETY NOTE Cnoaee a IxMeclive burtaarg material that nes a Critical HeIgM Value of et least the naignl of the Highest Actessinle PaNFall Heiphlcf NeaQxanlaquipment (Ref. ASrM FlIe7) 164077a Ix Jam Nuts ax Patch Nuts at Washers NOTE: Sufficient protec- tive surfacing must cover hardware to satisfy fall height requirements. DETAIL (6p/;' Flat washers SURFACE MOUNT w/'/2' Standard Hex Nuts Top of ----- -- ----- - Anchor Bolt e%� 7/e J • a I I < 19-22 Concrete L� Slab o ^� n ( T-4 Cbushed —Reck P!nW Bolls r-- �L7 Q1 r" a rn ?J ip D' cn Kids In Motion164075 i••• • Double Sh- e 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888.438-6574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 Document #1856340 ki, landscape structures' N5N SAFETY NOTE Chose a prolective wfto, melena' that has a Cntical Height Value of at least the height of the Highest Accessible ParUFell Height ofthe a4aceate WIPfre'a. (Ref ASTM Ff487) 13022100 PlayBooRoof 60171H STREET SOUTH, DELANO, MINNESOTA 55328-8605 888.574.4678 LSI Install Help 888-438-6574 LSI Direct 763-972-5200 Int. FA%�763) 972-3185 Document #21015500 1h landscape structures Parts List PlayBoosterA130567 Hex Shingle Roof Part# Description Qty. 127829 Hex Shingle Roof Section, Specify Color ............... 2 116573 Roof Sleeve.................................................................6 210156 Hex Shingle Root Hardware Package ................. 1 100198 14" x 1 14" BHCS w/Pin, SST ................................. 12 113027 1/," x I'/," BHCS w/Pin, SST .................................. 2 100362 '/,' Flat Washer, SST ................................................ 14 100610/," x'/." Drive Rivet, AUSST................................ 12 Specifications Hex Shingle Roof Section: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Roof Sleeve: Cast from 319 almag. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see spe- cific product installation/specifications). Installation Time: Approx. 3 man hours Weight: 182 lbs. Installation Instructions I) Connect hex roof sections together using'/," x 1 I/," BHCS w/pin with'/." Hat washers (lower 3 holes on each side) and'/," x 1 3/." BHCS w/pin with'/." Hat washers (upper hole on each side). 2) Attach roof sleeves to roof using'/," x I I/." BHCS w/pin with Ya" flat washers. Refer to the Roof Sleeve/Drive Rivet Attachment De- tail. 3) Position roof on roof posts with a minimum of 6 people. 4) Drill 1/," holes through roof sleeves using the predrilled 44" holes in posts as a guide. Insert 1/," x'/." drive rivets into drilled holes and tap pin in until it is flush with rivet head. Refer to the Roof Sleeve/Drive Rivet Attachment Detail. 5) Install protective surfacing before users are allowed to play on the structure. Em 0100339 DOt ., 21015500M 13021100. R,I hxAve,e Wkag 9/& landscape (2)'/;' x 1 3/;' BHCS w/Pin w/'/;' Flat Washers structures (Top Hole On Each Side) 1 I 1 C F_F i I F I E D SAFETY NOTE Choose a praecuve sunaang maleaal Vat has a Critical Meighl Value of at least the height bl the Highest Accessible PdNFdll Heightof Va abjarent equprtarn. (ReI.ASTM Ff4B).) 130221a0 DETAIL ROOF SLEEVE/ DRIVE RIVET ATTACHMENT of Sleeves o_ Cn �n o 3HCS w/Pin w/ '/,- Flat Nashers —ice c (12)'Q' x'/;' Drive RivetsZZE (3" down from top of post D rs and 1800 or 900 to each — other.) 130567 Hex Shinqle Roof Sheet 2 of 2 S & landscape structures® IS014001 TOP VIEW SAFETY NOTE Chose a protective surtaxing material mat has a Critical Heigh Vatue of at least the height of the Highest Accessible PaNFall HeigMof Ne aGacentequilxnent (Ref ASTM F148T.) 18384200 Sensory P reserved I Sheet 1 of 2 Document#18384200 J:IS PECS\ 183N 8384200. M5 Parts List Part# Description Qty. Model #168100 166757-00 Sensory Roto Main Wall, Specify Color ................. 1 167219-00 Wall Mount Plate, (DB), Specify Color .................. Model #168101 166758-00 Sensory Roto End Wall, Specify Color ................... 1 167219-00 Wall Mount Plate, (DB), Specify Color .................. * Model #168661 167186-00 Sensory Wall Plate, Specify Color ........................... 1 169036-00 Attachment Plate Hardware Package .................. 1 100353-00 3/6" Flange Nuts w/Pin, SST ..................................... 4 100365-00 '/8" SAE Flat Washer, SST .................... 4 100173-00 '/a° x 2" BHCS w/Pin, SST ....................................... 4 169179-00 2 -Hole Play Center End (DB) Hardware Pkg.... 1 100321-00 3/8" Patch Hex Nut, SST ............................................ 2 100362-00 '/e" Flat Washer, SST ................................................. 4 123224-00 3/8" x I "/16" BHCS w/Pin, SST ................................ 2 183890-00 4 -Hole Play Center Wall (DB) Hardware Pkg... 1 100321-00 '/8" Patch Hex Nut, SST ............................................ 4 100362-00 3/8" Flat Washer, SST ................................................. 8 123224-00 34" x 1 1146" BRCS w/Pin, SST ................................ 4 156846-00 Play Safe Label 2-12 Yrs .......................................... 1 183064-00 Warning Label............................................................ 1 169174-00 2 -Hole Play Center End (SM) Hardware Pkg... 1 100263-00 3/6" x 2 Y4" Expansion Anchors ................................ 2 100264-00 1/8" x 5" Expansion Anchors ..................................... 2 100327-00 '/6" Standard Hex Nut, SST ...................................... 2 100362-00 3/e" Flat Washer, SST ................................................. 2 169172-00 1 1/s" O.D. x 2" Long Spacer Tube, AL ................... 2 183891-00 4 -Hole Play Center Wall (SM) Hardware Pkg.. 1 100263-00 3/e" x 2 3/a' Expansion Anchors ................................ 4 100264-00 3/a" x 5" Expansion Anchors ..................................... 4 100327-00 3/a" Standard Hex Nut, SST ...................................... 4 100362-00 3/6" Flat Washer, SST ................................................. 4 169172-00 1 14" O.D. x 2" Long Spacer Tube, AL ................... 4 156846-00 Play Safe Label 2-12 Yrs .......................................... 1 183064-00 Warning Label............................................................ I * = Quantity Determined By Your Order DB = Direct Bury SM - Surface Mount Specifications Walls: Rotationally molded from U.V. stabilized linear low- density polyethylene, color specked. Wall Plate: Fabricated from 1/4" HRPO steel plate. Finish: ProSMeld*, color specified. Wall Mount Plate: Weldment comprised of 2.375" O.D. RS20 (.095"- .105") wall galvanized steel tubing and'/a' IIRPO steel plate. Finish: PmShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specificatiom). Installation Time: Main Wall (DB) 1 1/4 man hours End Wall (DB) 3/4 man hour Main Wall (SM) l V. man hours End Wall (SM) 3/4 roan hour Weight: Main Wall (DB) 88 lbs. Main Wall (SM) 54 lbs. End Wall (DB) 38 lbs. End Wall (SM) 21 lbs. Concrete: (DB) Approx. 1.31 cu. ft. per hole Installation Instructions (Direct Bury) 1) Refer to the Site Plan for footing locations. 2) Insert wall plate into main wall and attach, using 3/s" x 2" BHCS w/ pin with I/," SAE flat washers and'/s" flange nuts w/pin. Connect end wall to wall plate, using 3/s" x 2" BHCS w/pin with'/s" SAE flat washers and 3/g' flange nuts w/pin. 3) Attach wall mount plates to wall sections, using 3/a' x 1 11/16" BHCS w/pin with %11 flat washers and 3/a' patch hex nuts with 3/8" flatwash- on. Refer to the Direct Bury Detail. NOTE: Pull end wall and main wall sections together before tightening bolls. 4) With Sensory wall sections in position and plumb, pour concrete footings. Allow concrete to core a minimum of 72 hours before al- lowing users to play on the structure. 5) Apply labels as shown. 6) Install protective surfacing before users are allowed to play an the structure. NOTE: When a Sensory Play Center is installed in a play- ground environment, protective surfacing is required. (Surface Mount Without Protective Surfacing) 1) Insert wall plate into main wall and attach, using 3/a' x 2" BHCS w/ pin with %" SAE flat washers and 3/a' flange nuts w/pin. Connect end wall to wall plate, using Y.' x 2" BHCS w/pin with 3/8" SAE flat washers and Y." flange nuts w/pin. NOTE: Pull end wall and main wall sections together before tightening bolts. 2) With Sensory wall sections in position, mark anchor bolt locations on the concrete slab (through wall section holes). Move wall sec- tions aside. Drill 3/s" x 3" deep holes, using a hammer drill and Y." masonry bit. 3) Reposition wall sections. Tap'/s" x 2 3/,' expansion anchors into drilled holes. Fasten wall sections to 3/s" x 2 3/f expansion anchors, using 3/s" standard hex nuts with 3/.13 flat washers. Refer to the Sur- face Mount Without Protective Surfacing Detail. 4) Apply labels as shown. (Surface Mount With Protective Surfacing) 1) Insert wall plate into main wall and attach, using'/a' x 2" BHCS w/ pin with %" SAE flat washers and %" flange nuts w/pin. Connect end wall to wall plate, using'/s" x 2" BHCS w/pin with 3/s" SAE flat washers and 1/s" flange nuts w/pin. NOTE: Pul " wall and main wall sections together before tightening -bolts. (D crt 2) With Sensory wall sections in position LMOMk arRr bol tions on the concrete slab (through wall se ole@HMov sec- tions aside. Drill Y." x 3" deep holes, 09n6 harimer drfhwd '.- masonry bit..=.I n ON 3) Reposition wall sections with 1 '/a' 07D tfff2" loUS space £tibes in between bottom of wall sections and ciiRslaCrap 3/ x 'ex- pansion anchors into drilled holes. Fas3k wall spions t x 5" expansion anchors, using 3/a' standard Q?nuts widD/s" flat washers. Refer to the Surface Mount With Protective SurfaClig Detail. 4) Apply labels as shown. 5) Install protective surfacing before users we allowed to play on the structure. NOTE: When a Sensory Play Center is installed in a play- ground environment, protective surfacing is required. Eco #54517 D« .t#18384200 rep1aces#16871200. Added watviag tatxts to IaMware package. A& landscape structuress DETAIL DIRECT BURY 14.1 x 1 11/., — BHCS w/Pin wit 3/8" Flat Washers Sensory Wall Section DETAIL SURFACE MOUNT (WITHOUT PROTECTIVE SURFACING) 3/," Standard Hex Nuts w/ 3/;' Flat Washers Sensory Wall 3/," x 2 3/4" Section Expansion Anchors SAFETY NOTE - — Craosets IxoteWve sisrtsong itta'she"he' she"he' has a Cintical Height Value & atIs, I the P. height of the Highest Accessible =Fish Heigh MNeaQecenle9uipment (Rd. ASM F1487) 168712a NOTE: When LaSensory Play Center is installed in a play- ground environment, protec- tive surfacing is required. _7 DETAIL SURFACE MOUNT (WITH PROTECTIVE SURFACING) 3/," Standard Hex—J. Nuts w/ 3/." Flat Washers 3/al X 5" Sensory Wall Expansion Section Anchors I— Loose Fill 3/," Patch Hex- Protective Nuts W/ 3/,"Surfacing 1 14" D.D. x 2"----1W Flat Washers Protective Lobes ng Spacer Subgrade___i7a' •ii-T.15urfacing TI, - A tai Slab Wall Mount Plate 20 6gff&A&ii§i�iJ f-- Slab Crushed 4 Concrete Crushed Rock r"r Rock DETAIL SURFACE MOUNT (WITHOUT PROTECTIVE SURFACING) 3/," Standard Hex Nuts w/ 3/;' Flat Washers Sensory Wall 3/," x 2 3/4" Section Expansion Anchors SAFETY NOTE - — Craosets IxoteWve sisrtsong itta'she"he' she"he' has a Cintical Height Value & atIs, I the P. height of the Highest Accessible =Fish Heigh MNeaQecenle9uipment (Rd. ASM F1487) 168712a NOTE: When LaSensory Play Center is installed in a play- ground environment, protec- tive surfacing is required. _7 DETAIL SURFACE MOUNT (WITH PROTECTIVE SURFACING) 3/," Standard Hex—J. Nuts w/ 3/." Flat Washers 3/al X 5" Sensory Wall Expansion Section Anchors I— I —Unitary 1 14" D.D. x 2"----1W Protective Lobes ng Spacer �Jm •ii-T.15urfacing Concrete Tu Slab 6gff&A&ii§i�iJ f-- Slab Crushed 7fWT17f*7(WA�p, Crushed Rock r"r Rock Sensory Play Sensory Play Center -0 Sheet 2 of 2 C-601 7TH STREET SOUTH, DF NO, MINNESOTA e • 55328-8605 888-574-4678 LSI Install Help 888438-6574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 Document #183842M 9/& landscape structures" (2) Table S Panels Table Top' Panel Table Side Panel DETAIL _ TABLE TOP ATTACHMENT r� Table Panel (4)'/e' x 1 '/," Flat Head Cap Screws (4)Angle Brackets -Table Side Panel (4) a/e" Low Crown Cap Nuts w/ a/;' SAE Flat Washers Play 168105 eAFETY NOTE IghMClwose a pmtective sulldting material flat ISS YIW ��//�� � w//��/� has a Critical Height Velua of at least tha 1 , He gMAthe aQe a teQuiPmesn l(RHa STM 1 Po4B).) ca.unea 21054200 �Ill� ll�l -------- _- -------- Sensory - -- Sensory Wall (Sold Separately) ion Table I Sheet 1 of 2 Document#21054200 N 0 a n f � -4 �r Cn :<n� A ^?� i r ffi s t _ 1� CA Sheet 1 of 2 Document#21054200 Uvv� landscape structures" Parts List Sensory Play 168105 Imagination Table Part# Description Qty. 167171 Table Top Panel, Color Specified ............................. 1 167807 Insert Panel, Color Specified .................................... 1 167172 Table Side Panel, Color Specified ........................... 2 210557 Imagination Table Hardware Package ................ 1 100173 3/1" x 2" BHCS w/Pin, SST ....................................... 6 100199 3/e" x 2 1/4" BHCS w/Pin, SST .................................. 4 100252 3/1" x 1 '/J" FHCS, SST .............................................. 4 100349 '/a" Low Crown Cap Nut, SST .................................. 4 100353 '/1" Flange Nut w/Pia, SST ...................................... 10 100365 3/1" SAE Flat Washer, SST ....................................... 14 188664 Steel Angle Bracket, Silver ....................................... 4 Specifications Permalenc' Panels: Two color panel, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see spe- cific product installation/specifications). Installation Time: 3/a man how Weight: 20 lbs. Installation Instructions I ) Attach insert panel and table side panels to sensory wall, using 1/s" x 2" BHCS w/pin with 3/1" SAE flat washers and 1/s" flange nuts w/ pin. Attach angle brackets to table side panels and insert panel, using 3/1" x 2 14" BHCS w/pin with'/," SAE flat washers and 3/1" flange nuts w/ pin. Refer to the Insert Panel Attachment Detail. 2) Attach table top panel to angle brackets, using 1/g" x 1 1/4" flat head cap screws and 3/a' low crown cap nuts with 3/1" SAE flat washers. Refer to Detail. Eco pa10nJ58 Daamie"t p2105<JW rtplam pI686ggOD. Repixd heMvere package. '-- U i O O c^ U landscape structures BHCS w/Pin w/ 1/;' SAE Flat Washers DETAIL INSERT PANEL ATTACHMENT Sensory Play 168105 (magi (Sold Separately' n Table (6) 3/8' Flange Nuts w/Pin X200 int. FAX(763)972-3155 kl-t landscape structures, (6)3/1 % 2 1&" BHCS w/Pin w/ 3/," SAE Flat Washers Ring Panel 1 1 1 CERTIFIED (B) a/a" Flange Nuts w/Pin SAFETY NOTE Choose a protective swfaong ,atonal mat hate a C the Heigh Value si l leas) Pte height a the Highest Glue ofEle , `f4l Height of the adjacent equipment. (Rel. ASTM F1487.) 181287 Kaleidospin Panel I Sensory • i i Kaleidospin 601 7TH STREET SOUTH, DELANO, MINNESOTA 66328-8606 8885744678 LSI Install Help 868-438.6671 LSI Direct 763-972-52001nt. FA% (763) 972-3186 Document #18128700 A& landscape structures" Parts List Part# 181245 167014 169033 100199 100353 100365 Sensory Play 168108 Kaleidospin Panel® Description Qty. Kaleidoscope Panel Assembly, Specify Color...............I Ring Panel, Specify Color ........................1 Sensory Panel Hardware Package ...........................1 3/e" x 2'/," BHCS w/Pin, SST._ .................................... 6 3/a" Flange Nut w/Pin, SST............................................6 % SAE Flat Washer, SST.............................................6 Specifications Kaleidoscope N O Panel Assembly: (Panels) Two color Permalene" panels, color spec- fJ1 � Fn, ified. (Tubes) Weldntent comprised of 2.375" O.D. RS40 (.130"-.140") galvanized tubing and 7 GA. (.179") sheet HRPO steel. Finish: ProShield*, color Q> specified. (Mirror) Fabricated from 22 GA. (.030") Gm stainless steel sheet. Panels: Two color Permalene panel, color specified. Fasteners: Primagr fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see spe- cific product installation/specifications). Installation Time: V, man hour Weight: 53 lbs. Installation Instructions 1) Attach kaleidospin panel assembly to sensory wall, using ring panel,'/." x 2'/a" BHCS w/Pin with'/r" SAE flat washers and'/s" flange nuts with pin. F *54398n0.:Ynrml*18138)00 replaces *168)1000. Rcm vinngpardrmmuembly N O Q �n fJ1 � Fn, t C-) Q> I— Gm v M o� = o CM o' F *54398n0.:Ynrml*18138)00 replaces *168)1000. Rcm vinngpardrmmuembly 9/& landscape structures° It�r S014001 III "a 18428100 DETAIL (BACK SIDE) TM Sensory Play 177715 Color Splash Panel ® 2012 by LandscaW Simclures. All nghts reserve0 Document #18428100 U landscape structures' J.\SPECS\lW8428100 P 5 Parts List Sensory Play 177715 Color Splash PanelTM Part# Description Qty. 178123-00 Color Splash Panel Assy., Specify Color ..... ._._.... . 1 178144-00 Color Splash Wheel Hardware Package ............. 1 100175-00 3/," x 2 3/4" BHCS w/Pin, SST .................................. 6 100353-00 '/," Flange Nut w/Pin, SST ....................................... 6 100365-00 '/," SAE Flat Washer, SST ........................................ 6 Specifications Color splash Panel Assy.: Assembly comprised of (Permalenes Panels), color specified (Lexan Panel)'/," (6,35 mm) thick x 261/," (679,45 mm) diameter. (Acrylic Panel)'/," (3,18 mm) thick x 26 3/," (679,45 mm) diameter clear. (Color Wheel) .1875" (4,76 mm) thick x 23 7/16" (595,30 mm) diameter aluminum sheet. Finish: ProShields, image is transferred into paint by the process of infu- sion. (Shaft) 30(1 Series stainless steel. (rhmst Oilite Bearing).] 25" (3,18 mm) thick x 2.875"(73,03 mm) diameter. (Sleeve Oilite Bearing) 1.25" (31,75 stun) diameter x .750" (19,05 mm) long. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see spe- cific product installation/specifications). Installation T7me: 1/2 man hour Weight: 38 lbs. Installation Instructions I ) Attach color splash panel assembly to sensory wall, using'/," x 2'/," BHCS w/Pin with %" SAE Flat washers and %" Flange nuts with pin. NOTE: Color splash panel assembly can be attached on either side of the Sensory Wall. Remove protective laver from Texan before in- stallation. Fin,54521 � x18428100 rtp 01781]000. Upa m Nlah pmol w,mihly. N O O n F3 71 D-4 —4 C-) —< CT 1 __4 C-) =<rn a rn s C:) M Fin,54521 � x18428100 rtp 01781]000. Upa m Nlah pmol w,mihly. All landscape structures - BEFORE YOU BEGIN... If this SpyroSlide is to be installed on any playstructure other than the 56" high bracket on a P1ayBooster, contact landscape Structures before you begin. With three people, approximate installation time is 2 3/d hours. Check that all pans are included in the package (see listing on back page) and have not been damaged in shipment. If you notice any damage, do not begin assembly. Notify the carrier claims agent and Landscape Structures. Read the entire instruction sheet before you begin. TOOLS REQUIRED • BHCS Allen Wrenches (Supplied) • 16 oz. Hammer • '/,' Electric Drill • Y;' or "F" Drill Bit • °/,;' Wrench or Cresent Wrench • Carpenters Level • Tape Measure • Suitable equipment to dig footing holes and pour concrete footings. NOTE: If there is clamp In- terference, offset hanger clamp assemblies may need to be raised. PLAN VIEW SAFET'NOTE 10311111111 Choose a pnNMlve swfaalg malenal Ilial has a Critical Height Velue of at least the helphl W Ilia Highest Accessible ParUFall '�O® Ce,i r�-��aCenl equpmeM. (RBI.ASTM 18513600 IMPORTANT PRECAUTIONS! At least three people are required to safely install the SpyroSlide. Do not attempt it by yourself. Do not allow the slide to be used until: • Concrete footings have cured at least 3 days. • Protective surfacing is installed around slide. ELEVATION 81" 1, N II lI II 11 N O Loose Fill Top of c9.3 aG Protective _ Surfacing\ LM a/; PlayBoostel,4 122033SpyroSlide 9 1111 , Bracket, D: Sheet 1 of 2 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574.4678 LSI Install Help 888438-8574 LSI Direct 783-972.5200 Int. FAX (7631972-3185 02012byLandsraireSnctures Ail rights rese�ed DocuryXvSe­ 124 landscape structures` BARRIER/DECK/SLIDE ASSEMBLY Typical i___,i (4) Typical Offset Pla Booster (4) 4 3/e" Pipe Bolts Hanger Clamp Post V w/Ne" Flat Washers Assemblies 13 n _��(4) BHCSS w/Pi- BHCS w/Pin w/ 3/s' Flat Washers _ ~ (2) Barriers /(4) 3/e" x r/s BHCSw/Pin I , 1 (2) Barrier Plates ' � 1 , , 1 1 (8) 3/e 1 x 7/e BHCS w/Pin 1 w/ 3/e' SAE Flat Was 1 Washers A duud J_- Hanger Bracket - - Entrence Hoi 1 Deck L- 1 (2) Deck (4) 3/e. Hanger 1 1 Standard Hex ClampsNu I 11 'll w/'/" SAE (4) 3/s' x 1 3 BHCS w/Pin 1 1 (2) 3/s^ x,/," Flat Washers w/ 313" SAE Flat 1 \ BHCS w/Pin Washers (4) 3/e" x'/s' w/ 34" Flat Handbar BHCS w/Pin 1 •1 Washers W/ 3/s' Flat 1 1 DETAIL Washers 1 1 __. HANGER BRACKET ATTACHMENT 1 1 Post 1'1 1 (4) 3/s' x 1 n/+e' 1 BHCi/Pin 1 1 w/ 3/356 FI ' 0 WashBre:::j (2) Deck o c? -G Hanger Clamps �n He Bracket o SpyroSlide o, (2)'/;' Patch Nuts ' w/'/;' Flat Washers PlavBooster® 122033 SpyroSlideTM 56", Bracket, DB by LaMsca,,e Stmdures. All ngnts reserve' 185136b 9/& landscape structureso (2)318" Flat Washers (2)Rubber Bushings- (2)3/;' ushings------- (2)3/," Flat Washers� (2)3/," X 1 V," BHCS w[Pin . Limited Thread Bolts SPYROSLIDE EXIT SUPPORT SpyroSlide Center - Column SAFETY NOTE 151047cO DETAIL EAt SWW womi Exit Support DETAIL DETAIL DETAIL FOOTING LAYOUT SLIDE EXIT FOOTING CENTER COLUMN FOOTING PlavBooster® 122033 SpyroSlide' 56", Bracket, D13 Sheet 2 of 2 Loose Fill Loose Fill Protective Protective Su� Surf RM 69'Deck4r.. Concrete E sor 000 Footing E V i3r, E E Concrete Footing N N Concrete Footing 0 16 IlIl 7 73 - 12"' 73070 Crushed 410 Crushed 187 2611" 1 Rock Rock PlavBooster® 122033 SpyroSlide' 56", Bracket, D13 Sheet 2 of 2 k& landscape structures Parts List PlayBooster" 122033 SpyroSlide"" 56", Bracket,1313 Part# Description Qty, 130099 SpyroSlide, Specify Color ......................................... 1 130686 Barrier, Specify Color ............................................... 2 130687 Hood, Specify Color .................................................. 1 119499 Handbar, Brown......................................................... 1 119501 Barrier Plate, Specify Color ..................................... 2 121825 Entrance Deck, Specify Color .................................. 1 184259 Hanger Bracket, Specify Color ................................ 1 130224 56" Center Column (DB), Specify Color ................ 1 150941 Exit Support (DB), Specify Color ............................ 1 136551 4 1/," Aluminum Pipe Bolt, Specify Color .............. 4 105327 5" Half Clamp, Specify Color .................................. 6 113729 Offset Hanger Clamp, Specify Color ....................... 4 106022 Deck Hanger Clamp, Specify Color ........................ 2 106580 Hanger Bracket Hardware Package .................... 1 100198 3/a" x I '/: BHCS w/Pin, SST..... ............................. 4 100321 1/6" Hex Patch Nut, SST ............................................ 2 100351 1/g" Tee Nut, SST ........................................................ 4 100362 3/a" Flat Washer, SST ................................................. 2 100610 '/," x 3/," Drive Rivet, AUSST................................. 2 114309 Rail Hardware Package .......................................... 2 100198 3/4" x I '/," BHCS w/Pin, SST .................................. 8 100203 1/," x 2 Y." BHCS w/Pin, SST....... ........................... 4 100351 3/, Tee Nut, SST ........................................................ 8 100610 114" x 1/," Drive Rivet, AL/SST................................. 4 121245 SpyroSlide Hardware Package ............................. 1 123224 1/," x 1"/„” BHCS w/Pin, SST ................................ 4 100196 1/a" x 7/a" BHCS w/Pin, SST .................................... 18 100198 3/s* x 1 '/a" BHCS w/Pin, SST .................................. 4 100203 5/," x 2 114 BHCS w/Pin, SST .................................. 4 100327 1/," Standard Hex Nut, SST ...................................... 4 100353 3/a" Flange Nut w/Pin, SST ....................................... 4 100365 311" SAE Flat Washer, SST ....................................... 20 100366 1/," Flat Washer, SST ................................................. 8 100362 1/," Flat Washer, SST ................................................. 6 121246 Exit Hardware Package .......................................... 1 100292 14 x 1 '4" BHCS w/Pin Ltd. Thread Bolt, SST .... 2 100362 '/," Flat Washer, SST ................................................. 4 111442 Rubber Bushing......................................................... 2 DB—Direct Bury $Deciflcations Slide, Hood & Cast aluminum. Finish: ProShield, color specified. Barriers: Rotationally molded from U.V. stabilized linear low- density polyethylene, color specified. Entrance Deck: Flange formed from 12 GA (.105") sheet steel con- forming to ASTM A1011. Standing surface is perfo- Installation Time: ratedw3th5/,a' diameter holes and measures 32'/, wide Concrete Req.: x 36'1/,3" long. Finish: TenderTufl"', color specified. Barrier Plates: Fabricated from'/," x 1 1/1" zinc plated HR flat steel. Weight: Finish: ProShieldr, color specified. Center Column: Fabricated from 3.500" O.D. RS -20 (.120" - .130") galvanized steel tubing. Finish: PmShield, color speci- ed. E33t Support: Weldmeot comprised of 2.375" O.D. RS -20 (.095" - .105") galvanized steel tub ingg and'/," x 3" x 11 1/," mounting plate. Finish: ProShield, color specified. Handbar: Formed from %" O.D. 11 GA (.120") steel tubing. Finish: Tenderfuff, brown in color. Hanger Bracket: Formed from 11 GA ( 120") HRPO low carbon sheet steel. Finish: TendaTuff, color specified. Pipe Bolts: I '/ " O.D. 6005-T5 aluminum extrusion with wars. Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperyrWf rn design, stainless steel (SST) MASTM F 879 unless otherwise indlmt d (see specific prod- uct installation/specifications). Installation Time: Approx. 2 3/, hours with 3 people Concrete Req.: Ap(pp2rox. 6 cu. ft. Area Req.: 8' 43 m) minimum use zone at Exit Weight: 3 403 lbs. Fall Height: 56" (1,42 m) Installation Instructions l) Dig footing holes to the spacing and depth shown. 2) Preassemble the spyroslide and hood over a clean non -scratching surface. 3) Slide the center column into the spyroslide, and bun it up light against the bottom sleeve. 4) Attach the hood to the spyroslide using'/a' x 1 'Ye" BHCS w/Pin with'/," SAE flat washers and 1/," flange nuts w/llrn. Refer to the Barrier/Deck/Slide Assembly. 5) Mark posts at 55'/," above finished grade. Attach deck hanger clamps to hanger bracket using 3/ " hex ppatch nuts with'/," flat washers. Position hanger bracket withdeck han erclam�sbetween posts level with marks. Attach to is uslnRR 5" halt olamps, / " x 1 I/r" BHCS w/Pin and'/," tee nuts. Retpe, to the Earrier/Deck/Sllde Assembly. 6) With threepeople minimum attach the entrance deck to the face of the hanger bracket using'/,' x 1 '/," BHCS w/Pin with 1/ " SAE flat washers and'/ " standard hex nuts with'/," SAE flat washers. Refer to the Barrier/beck/Slide Assembly. 7) Set thepreassembled spyroslide into the footing hole with inserts in line with the holes in the face of the entrance deck. Attach usingg 3/ " x 1/ " BHCS w/Pin with'/," flat washers. Refer to the Barrier/De& Slide Assembly. 8) Attach the exit support to the spyroslide using 3/," x 1 I// " wash- ers. S lirmted thread bolts /." flat washers, rubber bushings r NOTE: At1acA bolls in the center ojlhe slots to allow1br expan- sion and contraction. Snug bolts dawn onht do not owrltghten. Re- fer to the Exit Support Detail. 9) Attach the barrier plates to the barriers using 3/a" x r/a" BHCS w/Pin. Refer to the Barrier/Deck/Slide Assembly. 10) Attach the barrier plates with barriers to the spyroslide and hood using 1/x r/ BHCS w/Pin with 3/," SAE flat washers. Refer to the Banner/DecOSlide Assembly. 11) Attach offset hanger clamp assemblies to posts at heights shown, using 5" half clam,Ps.'/ " x I '/ " BHCS w/Pm and'/," tee nuts. Refer to the Typical Onset Hanger Ctlamp Spec Sheet. 12) Attach barriers to offset hanger clamp assemblies with 4 3/a" pipe bolts between barriers and offset hanker clamp assemblies. Attach barriers to pipe bolts using 5/," x 2.'1," BHCS w/Pin with 1/, flat washers elated on each side of barrier. Attacheipe bolts to offset hanger clamp assemblies using '/."x 2'/," BHCS w/Pin. Refer to the SpyroSlide Assembly. 13) Attach handbar to hood usingg '/," x 3/ " BHCS w/ke with 3/f flat washers. Refer to the BarrierQk/SAcAssemblyE_� 14) Level barriers and entrance deck. You lWy need Vadjust hanger clamp assemblies and prop up slide to dM, 15) Install'/ "x 5/8" drive rivets in all 5" half e'}dtop{. Raf +to thecal Offset }anger Clamp Spec Sheet. n _e 1 16) With slide plumb and level, poor concre�,fpe)ingulolow c nerete to core a minimum of 72 hours before us allowed to a on the structure. 17) Install protective surfacing before use lowig to plthe structure. yx v D o M Eco MS 551 O unanr 18513600 ree 151NW. Re IwW hanger bwka landscape structures PLAN VIEW Typi Foo 32" Deck SAFETY NOTE Chose a prdectiva surleong malenal Nal /� nas a Cntiwl Height Value of at least Ne ISO 140011 , hHegMo Ne erye a tey ipmenl l(RN S aM ce �i iiea Tuazl 16106000 ELEVATION PlayftosterO 123331 Double •ly Slide,Sheetof 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888-438-6574 LSI Direct 763-972-5200 Int. FAX (763) 972-3785 rr Document #1610800M k& landscape structures' J \SPECS\161\16108000. P65 Parts List PlayBooster° 123331 Double Poly Slide, 32' Part# Description Qty - 127449 -00 32" Double Poly Slide, Specify Color .............. 1 150941-00 Support, (DB), Specify Color ............................ 2 151007-00 Support, (SM), Specify Color ........................... 2 100583-00 40'/,6' Rail, Aluminum, Specify Color .......... 1 113468-00 Spacer Tube, Specify Color ............................... 2 131987-00 Hood, Specify Color ........................................... 1 105327-01 5" Half Clamp. Specify Color ........................... 4 113729-00 Offset Hanger Clamp, Specify Color ................ 4 132443-00 Rail Spacer, Specify Color ................................ 2 111508-00 Slide Hardware Package ................................. 1 100196-00 3/," x 7/."' BHCS w/Pin, SST ............................. 4 100362-00 3/," Flat Washer, SST .......................................... 8 100292-00 3/g" x 1'/4" BHCS w/Pin Ltd. Thread Bolt, SST 4 100365-00 3/," SAE Flat Washer, SST ................................. 4 111442-00 Rubber Bushing..................................................4 106577-00 Hood Hardware Package 100198-00 3/," x 1 '/," BHCS w/Pin, SST ............................ 8 100200-00 3/," x 3 1/2" BHCS w/Pin, SST ............................ 2 100203-00 3/g" x 2'/4" BHCS w/Pin, SST ............................ 2 100351-00 3/g" Tee Nut, SST ................................................ 8 100362-00 3/," Flat Washer, SST .......................................... 2 100610-00 1/4" x'/," Drive Rivet, AL/SST ......................... 4 121348-00 4 -Hole (SM) Hardware Package .................... 1 100266-00 1/2" x 2 3/4" Expansion Anchor. .......................... 4 100322-00 '/2" Standard Hex Nut, SST ............................... 4 100363-00 '/2" Flat Washer, SST .......................................... 4 DB = Direct Bury SM = Surface Mount Specifications Slide: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Support: Weldment comprised of 2.375" O.D. RS -20 (.095" - t T .105") galvanized steel tubing and 1/4" x 3" mounting t plate. Finish: ProShield®, color specified. Hood: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Rail: Extruded from 1.125" O.D. x.312" W. 6005-T5 alu- D minum. Finish: ProShield, color specified. j Rail Spacer: Fabricated from 1.3125 O.D. x 16 Ga. (.065) steel tub- rn ing. Finish: ProShield, color specified. SpacerTbbe: Made from 6061-T6 aluminum '/8" O.D. x 1 11461. Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 2 42 man hours Concrete Req.: Approx. 2.6 cu. ft. Area Req.: 6' (1,82 m) minimum use zone at exit Weight: 11 lbs. Fall Height: 32" Deck (0,81 m) Installation Instructions 1) (Direct Bury) Dig footings spaced as shown. 2) Insert 40'/16' rail through top of hood, place rail spacer tube on each end of the 40 7/16" mil and attach to posts at height shown using offset hanger clamp assemblies.Refer to the typical offset hanger clamp spec sheet. Fasten bottom of hood to clamps using'/," x 3 1/2" BHCS w/pin, 3/," flat washers and spacer tubes. Refer to Detail 1. 3) Attach supports to slide using 3/a' x 1 '/4" BHCS w/Pin limited thread bolts, 3/," SAE flat washers, rubber bushings and 3/," flat washers. Refer to Detail 3. NOTE: Attach bolts in the center of the slots to allow for expansion and contraction. Snug bolts down only, do not overtighten. 4) Attach slide to the face of the deck using 3/," x'/8"BHCS w/Pin with 3/," flat washers. Refer To Deck Connection Detail 2. 5) Install'/f x %" drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 6) (Direct Bury) With supports plumb pour concrete footings. Allow concrete footings to cure for a minimum of 72 hours before users are allowed to play on the structure. (Surface Mount) Mark anchor bolt locations on concrete slab through holes in anchor plate and remove slide. Drill 1/2" x 3" deep holes on marks into concrete using a hammer drill and'/2" masonry bit. Tap expansion anchors into drilled holes. Reposition slide and reattach to the face of the deck following step 4. Fasten anchor plates to ex- pansion anchors using 1/2" standard hex nuts with '/2" flat washers. 7) Install protective surfacing before users are allowed to play on the structure. N O O D � C:)■ C-31 t T C") =;c t =<rm M a 0 0 D C7 rn Eco #53372 Dmu t#16108000 WnN15101400.R9ylxe3alumi"wi"eaa.s. j & landscape structurese Post DETAIL 1 (2)e/e" x 2 1/4' HOOD ASSEMBLY 4 BHCSw/Pin (2) 1 5/,e' O.D. x 1 11/,a' ' Rail Spacers Top of aMP _ -" Hood 407/,." Rail l l 32" Deck -1 (2) Spacer TUtle3 01 ,tyeewr (2),/e' x 3 f/z' BHCS w/Pin w/a/,'Flat DETAIL Washers SURFACE MOUNT Expansion Anchors4 Rul W/ 1/2" Flat Washers Support gushi11l (4) Offset Hanger t/, Standard Hex SAE FI N Wash Nuts Washers DETAIL 2-------(4)3/;' x 1 1U' ------ -- w/Pin Limited DECK CONNECTION _ Thread (4) a/;' x'/;' BHCS w/Pin w/ (4) 3/8' Flat Washers Rock NOTE: Sufficient protec- tive surfacing must cover hardware to satisfy fall height requirements. layBoostee 123331 1 • • 501 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-0678 L: Footing SAFETY NOTE Choose a 18oleaive su"aang materiel Net hes a Cnlical Haight Value 0 at leasI the haiBht of the Highest Accessible P.NFell He1BMMthe edjacenleyuilxrieM (Ref ASTM Ff487.) 161080a HOOD -HANDLE DETAIL DETAIL 3 SUPPORT Slide yst �f—(4) —:/.J Flat of ..f ,e Slide,of 888-438.6574 LSI Direct 763.972-52001nt. FAX (7631972-318`, �•"IMM-Me:11• V— landscape structuresd Typical PlayBooster Post \; Hood Asay.- i - See Detail h--'1 I , I 1 I 1 I I I , I , 1 , I , I , I , I ; I I 48.-56. Deck I I I I I I 1 I •�I I f I I�� I I I I 1 1 I I I I 1 1 I � I I I I I I I I I I I I ' I 1 I I I I 1 I I I I I I I I i I I I I I I I I DETAIL MID -SUPPORT Mid -Sul Loose Fill Protective Surfacing ' �•' See C -I I' Key _C 0 TypicalW) Concrete Footing I , SAFETY NOTE Choose a protective sudadng malenal that has a Critical Height value M at bast an height of the Highest Accessible PaNFall 'SO 14UU1 Height o1 the adjacent equipment (Ref. c.rwl.d ASTM Fl M7) 13319300 PLAN VIEW/ FOOTING LAYOUT Deck Conn•c6on Sa• Detail T1 IA\�\'w Mid -Support n E 'c 0 2 Wave Poly Slide Protective 0 Surfacing b 11 —moi e. Support Conniij `" r'' -See Detail• y y. T J Crushed Iklll -.. Boostee 123336 Double Wave Poly Slide, 1 STREET SOUTH, DELANO. MINNESOTA 66328-8606 868.6744676 L I Instal Help 888-438-6674 LSI Direct 763-972-6200 Int. FAX (763) 9721 Documetit#21244TIM (1 n PlayBooster° 123336 Double Wave Poly Slide, 48"-56" sndscape stnxtuver Parts List Part# Dacription Qty. 130716 48" - 56" Double Wave Poly Slide, Specify Cut or ........ 1 131987 Hood, Specify Color ... .................................... ........... .-.I 105327 5" Half Clamp, Specify Color ... ___ .................... ___.4 3/; Flat Washer. SST.....................................................2 113729 Offset Hanger Clamp, Specify Color ............................4 121348 100583 40'/,; Aluminum Rail, Specify Color__. __ ............ 1 113468 Spacer Tube, Specify Color...........................................2 100363 116908 64" Mid -Support (DB), Specify Color ..........................1 116917 54" Mid -Support (DB) Specify Color ..........................1 134565 28'/; Mid -Support. 48" Deck(SM),Specify, Color.._..1 134567 18'/," Mid -Support, 48" Deck(SM),Specify Col or ...... 1 116920 36" Mid -Support, 56" Deck (SM), Specify Color......._ 1 116921 26" Mid -Support, 56" Deck (SM), Specify Color ......... 1 150941 Support (DB), Specify Color.... ....... ............ .... 2 151013 Support 48" Deck (SM), Specify Color.........................2 151003 Support 56" Deck (SM), Specify Color .........................2 132443 Rail Spacer, Specify Color ............ .................... ._.... ..2 116943 Slide Hardware Package...........................................1 100196 '/a" x'/," BHCS w/Pin, SST..........................................4 100292 '/." x I '/4" BHCS w/Pin Ltd. Thread Bolt, SST ............ 8 100362 3/." Flat Washer, SST .................................................... 12 100365 '/." SAE Flat Washer, SST., ........................... ............... 8 111442 Rubber Bushing.............................................................8 106577 Hood Hardware Package..........................................1 100198 3/r" x 1 '/; BHCS w/Pin, SST.......................................8 100200 3/; x 3'/," BHCS w/Pin, SST... .................... ______2 100203 '/,"x2'4"BHCS w/Pin,SST._............. ..... .... .._..........2 100351 3/." Tw Nm. SST............................................................8 100362 3/; Flat Washer. SST.....................................................2 100610 '/4" x % Drive Rivet, AL/SST......................................4 121348 4 Hole (SM) Hardware Package ........................ _.....2 100266 '/;' x 2 3/4" Expansion Anchor.......................................8 100322 '/; Standard Hex Nut, SST...........................................8 100363 '/," Flat Washer. SST.._..._._.......__ ..............................8 DB - Direct Bury SM- Serrate Mount SDCCiflcations Slide: Rotationally molded from U.V. stabilized fnearlow- density polyethylene, color specified. Mid -Support: Weldment comprised of 1.660" O.D. RS -20 (.085" - .095") galvanized steel tubing and'/," x 3" flat steel. Finish: ProShield", color specified. Support: Weldraent comprised of 2.375" O.D. RS -20 (.095" - .105") galvanized steel tubing and'/," x 3" mounting plate. Finish: ProShield, color specified. Hood: Rotationally molded from U.V. stabilized linear low- density polyethylene, color specified. Rail: Extruded from 1.125" O.D. x .312" W. 6005-T5 aluminum. Finish: ProShield, color specified. Rail Spacer: Fabricated from 1.3125 O.D. x 16 Ga. (.065) steel tubing. Finish: ProShield, color specified. Spacer Tube: Made from 6061-T6 aluminum'/," O.D. x 1 Finish: PmShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tam- perpmof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Installation Time: (DB) - 3 man hours Installation Instructions I ) (Direct Bury) Dig footings spaced as shown. Refer to the Key for the exit support and mid -support depths of bury. 2) Insert 40'/„” rail through top of hood, place rail spacer tube on each end of the 40'/,; mil and attach to posts at height shown using offset hanger clamp assemblies. Refer to the Typical Offset Hanger Clamp Spec Sheet. Fasten bottom of hood using 3/,' x 3 '/," BHCS w/Pin with 34" flat washers threl clamps, spacer tubes and into threaded inserts in hood. Refer to the Hood Assembly Detail. 3) Attach mid -supports and exit supports to slide using'/." x V/," BHCS w/Pin limited thread bolts, 3/." SAE flat washers, rubber bushings and 3/; flat washers. Refer to the Support Detail and the Mid -Support Detail. NOTE: Attach bolts in the center of the slots to allow for expansion and contraction. Snug bolts down only: do not over -tighten! 4) Attach slide to the face of the deck using 3/a' x'/," BHCS w(Pin with 3/a" flat washers. Refer to the Deck Connection Detail. 5) Install 1/4" x'/," drive rivets in all 5" half clamps. Refer to the Offset Hanger Clamp Spec Sheet. 6) (Direct Bury) With supports plumb pour concrete footings. Allow concrete footings to cure for a minimum of 72 hours before users are allowed to play on the structure. (Surface Mount) Mark anchor bolt locations on concrete slab through holes in anchor plates and remove wave slide. Drill'/,"x 3" deep holes on marks into concrete using a hammer drill and'/," masonry bit. To expansion anchors into drilled holes. Reposition wave slide and reattach to the face of the deck following step 4. Fasten supports to expansion anchors using'/," standard hex nuts with'/," flat washers. 7) Install protective surfacing before users are allowed to play on the structure. N O eJs C-.) CC:�)7 C-)�- �c-) �, r fir' M m To- D o Q, Eco MOIUo421 Document p212GJ I W replaces k161 ar500 Ch"eti hood height dimmaon. (SM) - 2 man hours Concrete Req.: Approx. 5.2 cu. ft. Area Req.: 6'(1,82 m) minimum use zone at exit. Weight: (DB) - 174 lbs. (SM) - 158 lbs. Fall Height: Deck Height Installation Instructions I ) (Direct Bury) Dig footings spaced as shown. Refer to the Key for the exit support and mid -support depths of bury. 2) Insert 40'/„” rail through top of hood, place rail spacer tube on each end of the 40'/,; mil and attach to posts at height shown using offset hanger clamp assemblies. Refer to the Typical Offset Hanger Clamp Spec Sheet. Fasten bottom of hood using 3/,' x 3 '/," BHCS w/Pin with 34" flat washers threl clamps, spacer tubes and into threaded inserts in hood. Refer to the Hood Assembly Detail. 3) Attach mid -supports and exit supports to slide using'/." x V/," BHCS w/Pin limited thread bolts, 3/." SAE flat washers, rubber bushings and 3/; flat washers. Refer to the Support Detail and the Mid -Support Detail. NOTE: Attach bolts in the center of the slots to allow for expansion and contraction. Snug bolts down only: do not over -tighten! 4) Attach slide to the face of the deck using 3/a' x'/," BHCS w(Pin with 3/a" flat washers. Refer to the Deck Connection Detail. 5) Install 1/4" x'/," drive rivets in all 5" half clamps. Refer to the Offset Hanger Clamp Spec Sheet. 6) (Direct Bury) With supports plumb pour concrete footings. Allow concrete footings to cure for a minimum of 72 hours before users are allowed to play on the structure. (Surface Mount) Mark anchor bolt locations on concrete slab through holes in anchor plates and remove wave slide. Drill'/,"x 3" deep holes on marks into concrete using a hammer drill and'/," masonry bit. To expansion anchors into drilled holes. Reposition wave slide and reattach to the face of the deck following step 4. Fasten supports to expansion anchors using'/," standard hex nuts with'/," flat washers. 7) Install protective surfacing before users are allowed to play on the structure. N O eJs C-.) CC:�)7 C-)�- �c-) �, r fir' M m To- D o Q, Eco MOIUo421 Document p212GJ I W replaces k161 ar500 Ch"eti hood height dimmaon. V— landscape structuress (2)5/e" x 2 1/4 BHCS w/Pin . I f DETAIL HOOD ASSEMBLY 15/,."O.D. x 1 11/,e' Rail loerS (4) Typical Offset Lt I I 4011,.' i I I 1 I I 01 1 ------ Hood Hood I I ------------i -"_-_ 1 � (2) Spacer (2) %" x 31/," 1 Tubes DETAIL BHCS w/Pin w/ A = 41/;'/108 5/e" Flat SURFACE MOUNT Washers (8)112" x 2 %" Expansion NOTE: Sufficient protec- Anchors w/V;'Flat tive surfacing must cover hardware to satisfy fall Washers & /,' Standard Hex Nuts (3)Supports height requirements. I i'rr DETAIL DECK CONNECTION Concrl Deci<--- Slide (4) 5/;' x %" BHCS w/Pin w/ 3/e" Flat Washers SAFETY N07E Choose a pmtectNe surteunp material Nat hae a C -tical He19M Value of at least Ne help-! of Ne Hi9heal Accessi -le PaNFall Help -t 1 Ne a4lacent eQuipment. (Rel. A6TM F1187.) Typical PlayBooster HOOD -HANDLE DETAIL Post (4) Rubber Bush (4) 3/;' SAE Flat Washers (4) 5/;' x 1 '/." BHCS w/Pin Limited Thread - - Crushed Support — Rodt Concrete KEY: Deck H t Dimension 48" . A = 41/;'/108 56" . A = 11"/280 48" . B = 37 5/;'/959 56" B = 317790 48" C = 37"/940 56" C = 30'7760 DETAIL SUPPORT Top of Sliding Slide Surface (4)3/a' Flat Washers See A Loose Fill Key Protective 1 See B Key — o0Lo 12" pas 3 • � • • � • • •; e 01 7TH STREET SOOT ELAND, MINNESOTA 66328-860 88.574»1676 LSI Install Hel 88438-6674 LSI Dire63-97242001n Ax (763) 972-318 - 7 0 C-) f7 S 1 r r*I a m Y- U! DETAIL SUPPORT Top of Sliding Slide Surface (4)3/a' Flat Washers See A Loose Fill Key Protective 1 See B Key — o0Lo 12" pas 3 • � • • � • • •; e 01 7TH STREET SOOT ELAND, MINNESOTA 66328-860 88.574»1676 LSI Install Hel 88438-6674 LSI Dire63-97242001n Ax (763) 972-318 SAFETY NOTE Choose a protective surtaorg-at .. that has a Critical Height Value of et least Ne bl height of it IS014001 Heightoithea4height of the i�ntequme t(Rea ASTM 487) landscape � IM F, structures° DETAIL 20890900 TUNNEL/RING ATTACHMENT PLAN VIEW (2) Top (24)'/," x 1 V;' Attach Wire Tunnel Ings BRCS w/Pin To Panel With Tab FOOTING LAYOUT (2) Tunnel On Top Wire Panels Typical T n (24)'/," Flange PlayBooster Nuts w/Pin Post Wire Tunnel (4)'/;' x 3 a/;' Deck BHCS w/Pin R(2) Top Rings Tunnel /"_42"Panel / 01 Deck 0 0 (2) Bottom Rings (24) 3/e' X 1 1/8' BHCS w/Pin rl.1.10 Y. "• Surfacing DETAIL TENDERDECKS _---T-T� _(2) Tunnel Deck (8)'/e' x a/e BHCS w/Pin w/ a/a' SAE Flat Washers %" Flange z WPM 1071 (4) Space Tubes Tunnel 0 m DECK MOUNT 119641 Crawl Tunnel, Wire Deck Offset Hanger mp Assemblies ) 3/;' Flange uts w/Pin (24) a/;' Flange Nuts w/Pin N O CJS C-) s vX ry Sheet 1 of 2 ti Document#20890900 st& landscape structures, Parts List PlayBooster° 119641 Crawl Tunnel, wire Part# Description Qty. Below Deck Approx. 3'/i man hours ABOVE DECK 6'(1830 mm) 119760 Wire Tunnel, Specify Color......................................1 119624 Tunnel Panel, Specify Color ..................................... 2 119625 Top Ring, Specify Color ........................................... 2 120701 Bottom Ring, Specify Color ..................................... 2 105327 5" Half Clamp, Specify Color .................................. 4 113729 Offset Hanger Clamp, Specify Color ....................... 4 113468 Spacer Tube, Specify Color ...................................... 4 119936 Wire Tunnel Hardware Package ........................... 1 100198 3/." x 1 Y." BHCS w/Pin, SST ................................. 24 100353 3/,' Flange Nut w/Pin, SST ...................................... 24 124900 Tenderdeck Mounting Hardware Package......... 2 124460 '/,' x 3 1/4" BHCS w/Pin, SST .................................. 4 100196 3/," x'/." BHCS w/Pin, SST ..................................... 8 100198 3/,' x 1 '/," BHCS w/Pin, SST .................................. 8 100351 3/." Tee Nut, SST ........................................................ 8 100353 '/a" Flange Nut w/Pin, SST ...................................... 12 100365 3/a" SAE Flat Washer, SST ........................................ 8 BELOW DECK 119760 Wire Tunnel, Specify Color ...................................... 1 119624 Tunnel Panel, Specify Color ..................................... 2 119625 Top Ring, Specify Color ........................................... 2 120701 Bottom Ring, Specify Color ..................................... 2 113464 Angled Panel Bracket, Specify Color ...................... 2 105327 5" Half Clamp, Specify Color .................................. 8 113729 Offset Hanger Clamp, Specify Color ....................... 8 113468 Spacer Tube, Specify Color ................................. ._.4 119936 Wire Tunnel Hardware Package ........................... 1 100198 3/a" x 1 '/." BHCS w/Pin, SST ................................. 24 100353 '/,' Flange Nut w/Pin, SST ............................ --- ... 24 124947 Ground Level Mounting Hardware Package..... 2 124460 '/a" x 3 '/," BHCS w/Pin, SST .................................. 4 100195 3/e" x'/," BHCS w/Pin, SST ..................................... 8 100198 '/." x 1 '/," BHCS w/Pin, SST ................................. 16 100203 5/8" x 2 '/," BHCS w/Pin, SST .................................. 4 100351 3/." Tee Nut. SST ....................................................... 16 100353 3/." Flange Nut w/Pin, SST ...................................... 12 100610 '/," x 5/," Drive Rivet, AL/SST................................. 8 Specifications WireTunnel: Formed from'/4" diameter wire with 2" x 3" openings. Wire tunnel measures 28" in diameter and 35 3/." long. Finish: Tendelfufl"', color specified. Permalene" Panel: Solid color panel measures 35 5/." wide x 41" high, color specified. Rings: Solid color Permalene, color specified. Angled Panel Brkt: Weldment comprised of. 190" thick 5052 aluminum formed angle with (2) 6061-T6 aluminum threaded tubes I /," O.D. x 1 '/2" long. Finish: ProShield', color specified. Spacer Tube: Made from 6061-T6 aluminum'/." O.D. x 1 11/o". Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Above Deck Approx. 3 man hours Below Deck Approx. 3'/i man hours Min. Use Zone: 6'(1830 mm) Weight: Above Deck 124 lbs. Below Deck 136 lbs. Fail Height: Deck Height Plus 4" (101 mm) Installation Instructions ABOVE DECK I ) Attach the wire tunnel to the panels using top and bottom rings,'/," x I '/." BHCS w/pin and'/,' flange nuts w/pm. Refer to the Tunnel/ Ring Attachment Detail. 2) Attach thepanels to the face of the decks using'/." x'/J' BHCS w/pin '/ with." SAE flat washers and 3/." flange nuts w/pin. Refer to the Tenderdeck Detail. 3) Attach the offset bangger clamp assemblies to the posts using 5" half clamps and'/e" x I '/." BHCS w/pin with 3/." tee nuts. Refer to the Typical Offset Hanger Clamp Spec Sheet. 4) Attach the panels to offset hanger clamp assemblies using 3/." x 3 3/," BHCS w/pm, spacer tubes and 'I," flange nuts w/pin as shown. 5) Install protective surfacing before users are allowed to play on the structure. BELOW DECK 1) Attach the wire tunnel to thePanels using top and bottom rings, 3/a" x 1 '/," BHCS w/pin and %" flange nuts w/pm. Refer to the Tunnet/ Ring Attachment Detail. 2) Attach the anled panel brackets to the bottom of the panels using 3/." x 5/a' BHCS w/pin and'/." flange nuts w/pin. See Below Deck Mount. 3) Attach the offset hanger clamp assemblies to the posts using 5" half clamps and 3/s" x 1 '/." BHCS w/pin with 3/a" tee nuts. Refer to the Typical Offset Hanger Clamp Spec Sheet 4) Attach the angled panel brackets with the �anels and wire tunnel to the offset hanger clamp assemblies using /." x 2 '/j' BHCS w/pin. See Below Deck Mount. 5) Attach the top of the Panels to the offset hanger clamp assemblies using 3/e" x 3 /4" BHCS w/pin, spacer tubes and /." flange nuts w/pin. See Below Deck Mount. ry 6) Install'/4"x'/." drive rivets in all 5" half clamps. Rego the Typical Offset Hanger Clamp Spec Sheet. �t.D('� pp� 7) Install protective surfacing before usersyreQowc%o plaf'i�{he structure.'q ---4c7 <1 o� � rn O CT) F 00100299 Dw:woc,a 20A9 t 1.01339 Ad nom 0 as ,h m"rcl wi tub m top. '� rgwzwff owl landscape structures° DETAIL TUNNEL/RING ATTACHMENT (2) Tunnt Panels(24) a/;' x 1 t/e' (2) Top Rings HCS w/Pin (24)'/a" Flange Nuts w/Pin Typical .meq iPlayBooster-_Post 11V'ji ;Tunnel ---48" or Hi_"---- -----TDeck(4) °/a" Flange--------- Nutsw/Pin «-- /- ------ange` 5ti(8) OffsetHanger (4) SpaClamp Assemblies Tuis 01 IamPop Rings o ProfedtUe Surfacing (2) Angled Panel Brackets 02015 by Landscape SWdures. All rights (24) 3/e" X 1 1/e BHCS w/Pin (8)'/a" Flange Nuts w/Pin SAFETY NOTE Choose a protective surtaaig material Ihet hes a Cbtical Height Velue of at least the height of the Highest Accessible ParllFall HeighlolNeadjacaM equpmenl (Rel ASTM FflBZ) 208909a I I Attach Wire Tunnel To Panel With Tab On Top li i riI � I , I , I , I , I , I , I ' I ' mac_% (4) °Q x 3 a/4" BHCS w/Pin BHCS w/Pin ( x BHHCSCS w/Pin I , I , I , \i I ' 0 lames Top ` � I ProfedtUe Surfacing (2) Angled Panel Brackets 02015 by Landscape SWdures. All rights (24) 3/e" X 1 1/e BHCS w/Pin (8)'/a" Flange Nuts w/Pin SAFETY NOTE Choose a protective surtaaig material Ihet hes a Cbtical Height Velue of at least the height of the Highest Accessible ParllFall HeighlolNeadjacaM equpmenl (Rel ASTM FflBZ) 208909a I I Attach Wire Tunnel To Panel With Tab On Top li i riI � mac_% 01 Z 119641 Crawl Tunnel, wire Wire Tunnel Sheet 2 of 2 V& landscape structures® DETAIL SIGN ATTACHMENT (4)'/;' Low Grown Cap Nuts wP/," SAE Flat Washers (2) Signs Age Appropriate Sign N Sign Post :2 N Small Border (4)'/j' x 1 Ve" BHCS w/Pin wi SAE Flat Washers CERTIFIED DETAIL SURFACE MOUNT (4)1/2" Standard Hex Nuts w/,12' Sign Post Flat Washers (4)1/2" x 2'/4' Expansion Anchors Concrete - Compacted Gravel Sign a -DETAIL 2 DIRECT BURY FOOTING Finished -,v.,Sign Post DETAIL t 11E-= Subgrade (2) #8 x 1 BHCS Torx (2) Borders Concrete Footing Z O Signs igns 305 Ulf Model 182503 - Landscape Structures Provided Welcome Sign N Model 182504 - Welcome Sign Signs Welcome Sign 31GE11331112M T—OrrIm.7170will MIMM= ® 2015 by Lshdsww Stmctures All rights reserved Document #21325600 Parts List Part# Description Qty. 211847 Warning Sign. Gray... .................................................... l 211846 Age Appropriate Si 2-12 Years, • 211848 Age Appropriate Sign, 2-5 Years, Gray ......................... 1/4-6 Lobe T-15 Tamp. Bit --- ......................................1 211849 Age Appropriate Sign, 5-12 Years, Gray. ...................... 100266 211850 Age Appropriate Sign, 1 '/2-5 Years, Gray .................... '/i Standard Hex Nut. SST...........................................4 211851 Age Appropriate Sign, 1 '/2-12 Years, Gray— ............... • 211852 Age Appropriate Sign, 6-23 Months, Gray ................... • - Quantity Determined 180598 Sign Post (DD, Speci . .._._._._....._._...... 181119 Sign Post (SM), Specify Color._._ .................__.... 193782 Large Border, Black.......................................................1 193783 Small Border, Black .................................................- I 213258 Age/Warning Sign Hardware Package .................... 1 100198 Y." x I'/," BHCS w/Pin, SST ... - ...................................4 100349 3/," Low Crown Cap Nut, SST......................................4 100365 H," SAE Flat Washer, SST .... --- .................................. 8 168323 M8 x V/ BHCS Tom, SST.............................................2 169413 1/4-6 Lobe T-15 Tamp. Bit --- ......................................1 121348 4 Hole (SM) Hardware Package...............................1 100266 1/2" x 2 %" Expansion Anchor .................................. --A 100322 '/i Standard Hex Nut. SST...........................................4 100363 'A" Flat Washer, SST.....................................................4 DB = Direct Bury SM - Surface Mount • - Quantity Determined By Your Order Specifications Sign Panel: Panel is fabricated from '/,"(.125"x3,17mm) alumi- num plate. Finish: ProShield", grey in color. (Sign) Digital image is tmnsfered to a'/e " (.125"x3,17 mm) ProShield coated aluminum plate, then infused into the ProShield. Border: Perrnalene, black in color. Post: Weldmentcomprised 2.375"(60,33 mm) O.D.RS20 (.095-.105) (2,41 mm -2,67 mm) wall galvanized tube,'/," (6,35 trun) HRPO steel sheet and aluminum post cap. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tam- perproofin design, stainless steel (SST) MASTM F 879 unless otherwise indicated (see specific product installation/specifications). Installation Time: (DB) Approx. 1 man hour (SM) Approx. '/r man hour Concrete Req: Approx. 1.31 cu. ft. Weight: (DB) - 24 lbs. (SM) - 27 lbs. Welcome Sign Installation Instructions Direct Bury 1) Dig footing hole to depth and diameter shown. 2) Attach sign panels and borders to post as shown, using'/," x P/r" BHCS with '/," SAE flat washers and'/," low crown cap nuts with'/r" SAE flat washers. Attach signs to borders using 88 x'/2" BHCS Tom. 3) Set sign assembly in footing hole and temporarily brace in plumb position. 4) Pour concrete footing. After concrete has cured, remove bracing. Surface Mount 1) Attach sign panels and borders to post as shown, using'/," x I'/," BHCS with Y. SAE flat washers and'/s" low crown cap nuts with 3/," SAE flat washers. Attach signs to borders using M8 x'/2" BHCS Tom. 2) With sign in proper position, using a'/2" masonry bit and hammer drill, drill 3" deep holes into concrete slab through holes in post plate. Tap I/r" x 2'/," expansion anchors into holes and secure using '/2" standard hex nuts with I/2" flat washers. E 40100457 nucunxm 421325600 replaces 421151400. Clanged "p W" numbers & replaced hardware. N 0 cn C-) Y --t Cr ' tT rn y ..c .. O m E 40100457 nucunxm 421325600 replaces 421151400. Clanged "p W" numbers & replaced hardware. 110070 is the Site Plan Not an Install doc. N 0 o� r rn �x �n Y � N V— landscape structures® a/e' x 1 BHCS '14"x sus" Rivet 5" Half SAFETY NOTE Choose a protective surfadig material that has a Critical Height Value of at least Ne height of the Highest Accessible Pal Height ONe adacant equipment (W ASTM F14BT.) 31-94 11002200 Tee Clamp Assemb N low 01994 by LarWscape Structures. All rights reserved Document #11002200 k& landscape structures* J \SPECV 110111002200.P65 Parts List Part# Description Qty 105327-01 5" Half Clamp, Specify Color .................................. 2 100198-00 '/e" x 1 '/." BHCS w/Pin, SST ................................... 4 100351-00 '/e" Tee Nut, SST ........................................................ 4 100610-00 1/4" x'Is" Drive Rivet, SST ....................................... 2 Specifications Tee/Beam: 356 alloy treated to T-6 hardness and welded to 5" aluminum beams or mechanically fastened to 5" steel beams. Finish: Powdercoat, color specified. Half Clamps: Cast aluminum. Finish: Powdercoat, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx.'/imanhour Weight: 2 lbs. PlayBooster°Tee Clamp Assembly Installation Instructions 1) Locate and mark center of clamp location on 5" pipe. 2) With beam in position, fasten 5" half clamps to tee clamp using %11 x 1 14" BHCS w/Pin and tee nuts as shown. Tighten cap screws evenly. 3) IMPORTANT: Install drive rivets in half clamps by drilling holes in clamps and into 5" pipe using a'/r" or "F"(only) dill bit. Insert rivet in hole, and hammer rivet pin in until it is flush with head. N O 0 n —4 /-% Ql rn a M o� �x a o 7� o m 115176 is a hard surface label Not an Install doc. 9& _ `-' landscape structures° NOTE: Surface mounting will not work in all applications. Consult Landscape Structures Inc. for your particular re- quirements. CONCRETE SLAB SPECS • Base under slab to be 4" - 6" of sand over a stable subgrade. • Depth of concrete slab to be 4" - 6" with a wire mesh support. • Minimum of 7 days curing time full cure after 30 days. • Surface of concrete to be trowled smooth and acid etched. • Concrete: 3000 PSI (Min) 30 Days 3500 PSI '/, Minus Crushed Rock NOTE: Sufficient protec- tive surfacing must cover hardware to satisfy fall height requirements. NOTE: Drill 3" deep hole using hammer drill and %"masonry bit. Tap anchors into concrete and secure with'/2" standard hex nuts and %" flat washers. 'a Q- aQ a d- SAFETY NOTE Choose a prolective aurtaarq malenal Met Ma a Critical Heigh( Veloe of et least Ine neigh of me Highest Accessible P."." Heigh pfinaa4acenl equpl_I (Ret.ASTM r„en 3-29-01 12194700 /'/e' x B" Square Steel or Aluminum Plate Continuously Welded to Upright Post DETAIL (4) %" Standard 1 Hex Nuts WashFlat\ Washers Upright (4)112" x 2'/4' Post Expansion Anchors I Surface 8- Specs, 200 fy.• 614' f/, 7,, f'I 1 165 1 At a o g o� to 17– m • a 0 0 t.0 o y' cn 'a Q- aQ a d- SAFETY NOTE Choose a prolective aurtaarq malenal Met Ma a Critical Heigh( Veloe of et least Ine neigh of me Highest Accessible P."." Heigh pfinaa4acenl equpl_I (Ret.ASTM r„en 3-29-01 12194700 /'/e' x B" Square Steel or Aluminum Plate Continuously Welded to Upright Post DETAIL (4) %" Standard 1 Hex Nuts WashFlat\ Washers Upright (4)112" x 2'/4' Post Expansion Anchors I Surface ayBooster® a, Specs, Surface Mount 7,, f'I At r-- -1 C) 01 c F 17– m �- m C t.0 o y' cn N ayBooster® Concrete Specs, Surface Mount 02Wt Ey LaMsCwSnmms. AIIdghtsreservW 1-30A7 0.mumcnl&121YJ]W rcpincablll4]IOW. Ulxlnlad hole°• Document#12194700 5 SAFETY ROTE Choose a Ixotaclive surfaa,g material Nal has a CMical Height Value of at least the height of the Highest AccassiDlP.Fer ( Heigh oadjacent eQuipment. (Ref. ASTMSTU F1467, SECTION 9 ) landscape structures," 42 42" 1070 1070 A A C Enclosures or components are required on any decks higher than 28" as indicated on your plan drawing. 56" 1 32" Dimension indicates center to center spac- ing of concrete footings. Number indicates height of deck above fin- ished grade. S - 48" 1 40" ,_ Letter indicates post length as indicated on lei your plan drawing. B B C Enclosures/ Components - Refer to your -- plan drawing for locations and their respec- (j tive spec sheets for installation. UVertical Ladders - Refer to your plan draw - 40" rl ing for locations and the Vertical Ladder spec Deck II u sheet for installation. Decks - Refer to your plan drawing for heights and orientation. Refer to the appro- priate deck spec sheet for installation. Deck Hanger Clamp Assembly - Refer to the appropriate Deck Assembly spec sheet for installation." 16" Deck C:) Concrete Footings:_ ftfercW the I at Concrete Footing spl"i eet9- ins laven. Kick Plates - Refer #6ur plan draor K locations and the :Flatel�ec sIT gor installation. -- -�- ---j cn Booster General Post/Tende 6-1-95 1601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-860563) 972-3391 1.888-LSI-LSI(1-888-57446781 FAX 972-3185 • 1 / tl v�/L landscape structumr J %SPEcstoanowzzot.res PlayBooster General Post/Tenderdeck Information Installation Instructions Before Starting, Read the General Construction Guidelines, Installation Hints, All Typical Detail Sheets and Specific In. stallation Instructions for Each Component Labeled on Your Plan. I ) Dig footing holes spaced as shown on the plan and spec sheets. Re- fer to the Typical Concrete Footing Spec Sheet. 2) Note the post lengths as shown on the plan and set in their appropri- ate footing holes. The post length is indicated on the finished grade sticker on each post. 3) Mark the appropriate posts for the deck heights you are installing and attach decks to posts at marked height. Refer to the appropriate deck spec sheet for installation. 4) After all the posts are at proper heights and plumb, and the decks are at proper height and level, pour the concrete footings per the Typical Concrete Footing Spec Sheet. 5) Continue installing enclosures and components and pour concrete footings as you progress, making sure everything is plumb and level. 6) When installation is complete, install Drive Rivets in all clamps per the Typical Offset Hanger Clamp Spec Sheet. 7) Install protective surfacing under and around all equipment before users are allowed to play on the structure. 61-95 Ravi l UP&W Urawi . N 0 r cn _T1 C) t Cr tT t n L' o is landscape structures - Rails A Same Height DETAIL ASSEMBLED CLAMP Onset Hanger Clamp Assembly (2) %" Tee Nu '/a' x 2 '/," BHCS w/Pin Offset Hanger Clamp NOTE: Position with offset fac- ing down as shown. See De- tail for special applications. �5� The Offset Hanger Clamp allows rails to be installed at same height for special applications, like at 900 to each other as shown, or when there are clamp conflicts, offset can be positioned upward. SAFETY NOTE Choose a pteteclive surtaarg material Nat hese CMical Height Value of al least the height of the HlyheslA¢essiEle PaNFell HegM of(YreaQaoant WulPmahl (Ref ASTM F1/BZ) 14397 12382100 NOTE: A drive rivet is not required in all applications. See Drive Rivet Addendum for a listing of components that do not re- x rivets. X a/�� Drive Rivet T FHW (2)'/i x 1 'f� BHCS w/Pin PlavBooster° 114261 Offset Hanger Clamp Assem 6017TH STREET SOUTH, DELANO, MINNESOTA 55328_$605 (763)972.3391 1.888-LSI-INST (1.888.574.4678) FAX(763)972-3185 ID Document #12382100 N O O -1n a1 .<� A L f 4 M Cn N PlavBooster° 114261 Offset Hanger Clamp Assem 6017TH STREET SOUTH, DELANO, MINNESOTA 55328_$605 (763)972.3391 1.888-LSI-INST (1.888.574.4678) FAX(763)972-3185 ID Document #12382100 kb landscape structures' J lSPECSU23112392100.Paa Parts List PlayBooster°114261 Offset Hanger Clamp Assembly Part# Descriptlon Qty 100198-00 '/," x 1 Y." BHCS w/Piq SST .................................... 2 100351-00 Y." Tee Nut. SST ......................................................... 2 100610-00 Y." x'/." Drive Rivet, ALSST................................... 1 105327-01 5" Half Clump, Specify Color ..................................... 1 113729-00 Offset Hanger Clamp, Specify Color ......................... 1 100203-00 '/r" x 2 '/," BHCS w/Pin, SST .................................... 1 Specifications Clamp: Cast aluminum. Finish: Powdercoat, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) paASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx.'/,manhour Weight: 3 His. Installation Instructions 1) Locate and mark position of clamp on 5" post. 2) Position clamp in proper direction and assemble with'/a" x 1 '/s" BHCS w/pin and'/r" tee nuts as shown and lightly tighten. Position rail against clamp and screw in -%" x 2 '/j' BHCS w/pin until rail bottoms out on clamp. Final tighten all fasteners. 3) IMPORTANT: Drill through hole in 5"halJelamp and into 5"post with a t/," or "F" (onls) drill bit, insert rivet in hole and hammer rivet pin in until it is flush with head. 10-3-97 D-ument 0121921- )re Iwft 01 liM1M1 . Added r CRry NOTE: Ick I- -VI a 0 C� Ln a& landscape structurese Is' SAFETY NOTE Ghmse a protective •urlatinp mabrbl tliat hes a Critical Height Velw M at bast th height of the Hiphetl Acce•side PerVFall HeigMO/theaQawM equlprreM. (Ref ASTM FfIB).) 11-22-99 129847a0 129947b0 General Rules For Use Of Drive Rivets • Rivets are used as "Insurance" to keep clamps from sliding down the posts. In many cases this "Insurance" is achieved in other ways; i.e. Panels that attach to the deck face. • Refer to the Spec Sheet Parts List and follow Installation In- structions for each component. • Decks and Overhead Events always need rivets. • Any component fastened to the Deck does not need rivets. Typical Steel Half Clamp Rivet Pin \�l Benefits of not installing unnecessary rivets: saves time, it makes clamp adjustments as well as the removal of clamps for replacement or adding phases much easier, and you will have fewer damaged clamps or posts due to poor installation techniques. Typical PlayBooster Post Typical Aluminum Half Clamp , Rivet \Pin ce_ 9� STEEL '/,' x'/ '/;' x'/;' Drive Rivet Drive Rivet CLAMPS 100610 100611 N O �� Cn IMPORTANT- MPORTANT-'/4s 1/4"Hole Typical n� 1 Typical Aluminum Half Clamp , Rivet \Pin ce_ 9� STEEL '/,' x'/ '/;' x'/;' Drive Rivet Drive Rivet CLAMPS 100610 100611 N O �� Cn +n 0 C7 Typical n� 1 PlayBoosZr9— Post - r -,T M ionn�aar. '/4' Hole ALUMINUM CLAMPS NOTE: Use Only Bit Size "F" or'/;' Drill Bit. After Play Component Assembly is Complete, Drill Hole into Post Through Half Clamp, Insert Rivet in Hole, and Hammer Rivet Pin in Until it is Flush with Head. 6 0 1999 by Landscape SWMures. All lights reserved 11.3..99 Dovmrnl el 2Ve47M Nl(Wl9 , Added ge,urM rvles f-.:� fdmemets. Document#12984700 landscape structures° Post Offset Post Hanger � Clamp Hammer. .MP Half Clamp 4:4 BHS \ w/Pin Tee Nut 11-22-99 109729a 1) Drive Center Pin of Rivet Straight into Post Using'/," Diameter Punch and Hammer. 2) Unbolt BHCS w/Pin and Tee Nuts from Clamp Using Tamperproof Hex Wrench. Remove Offset Hanger Clamp. Lightly Tap on Half Clamp with Hammer Until Head of Drive Rivet Pulls Away From Half Clamp. Tools Needed: • Claw Hammer • '/," Diameter Steel Punch • Tamperproof Hex Wrench RemovalDrive Rivet 601 7TH STREET SODTH. DEL- NO. MINNESOTA 55328-8605 763 9723391 1-888-LSI-INSi 1-888-5744678 FAX 763 972-3185 N O_ 0 � 3) Pull Out Drive Rivet Us' awaknd J Hammer. .MP 3 O in Tools Needed: • Claw Hammer • '/," Diameter Steel Punch • Tamperproof Hex Wrench RemovalDrive Rivet 601 7TH STREET SODTH. DEL- NO. MINNESOTA 55328-8605 763 9723391 1-888-LSI-INSi 1-888-5744678 FAX 763 972-3185 120688 is a danger keep off sign Not an Install doc. 0 CD r 3 rn z cn N 120688 is a danger keep off sign Not an Install doc. cn N A& landscape structures• Loose Filly` , Protective Surfacing Subgrade Concrete Crushed Rock 12" - 300 /Typical Component Support ,,moi 1�'_i—, ���J!_'I• I� SAFETY NOTE r 9-25-00 10970900 N 0 co "' c'> :< a �rn s � w,D r [be n mple: ou are using 12" of se 11 material, your ncrete footing will 22" deep. Minimum 1.2 Cubic Feet of Concrete Required per Support. IayBooster Concrete Footings, Components , .. :, a 0 2" by Lardsape S Ctums All rights reserved. 8-25-11) Unvnmm bl 12173M wln<c. p(W709M, Added concrete rm,ing nole. Document#13237300 SAFETY NOTE J Chose e p o e° a pea q mate al pat nes a Cnlical Hei9nt Value of et leas) Om gh I5014001 t , HeYrM ohne acl leQ acenlupmein '.IlRet. SFTM r,.e7, landscape structures• PlayBooster Installation 1) Before starting installation, study your PlayBooster plan drawing and all installation instructions carefully for location of posts, deck heights, components and safety enclosures. Make sure slides are oriented away from the afternoon sun and that the structure is visible (easily supervised) and accessible. 2) Clear an area large enough for your PlayBooster and at least the required minimum use zone around it, as shown on your plan drawmf. The subsurface must be well drained. If the soil does not drain naturally it must be tiled or sloped at I/," to '/,' per foot to a storm sewer or a "French Drain". If your PlayBooster is over 30' in length it is recommended to Install more than one "French Drain" or similar system to allow drainage from the center of the play area and decrease the overall slope. If this is not possible, the structure may need to be "stepped" to take up the grade change. 3) Overhead Obstructions: Overhead obstructions within the use zones ofplayground equipment that are not part of the play structure (for example, tree limbs) shall be at least 84 in. (2130 mm) above each designated play surface or 84 in. (2130 nun) above the pivot point of swings. All overhead utility line clearances above the use zone areas shall comply with all local, state, and national codes, such as the National Electical Safety Code. 4) Locate all mainstructure post footing holes according to the dimensions shown on your PlayBooster plan. This can be accomplished by laying a deck on the *round and measuring from it; by laying out a base line string grid or using a builders transit. This step is very Important and worth taking extra time to be precise. Location of component footings such as slide supports can be done at a later time. 5) Refer to the Typical Concrete Footing installation sheet. Dig holes to the proper width and depth as shown. (Only dig enough holes for one day's construction. Do not leave holes open over night.) Pour crushed rock in each hole level with each other and at least 4" deep as shown. This can be easily accomplished either with a builders transit or by laying out hole locations with a string grid, leveling the grid, and measuring down from the grid for each footing. Tamp the crushed rock down until compacted and at proper level. This step is impor- tant to ensure all posts will be at the proper height relative to each other, and it greatly simplifies installation. If the soils are loose or unstable, larger diameter holes may be necessary. Check with a local engineer if in doubt. 6) Start with the lowest deck and work your way to the highest deck following instructions on the installation sheets for typical post/deck assembly. Install barriers and roofs as located on the plan for stability_, 0 7) After the posts are at proper heights and plumb, and the decks are at proper height and leiiil j omge cogwje footings per the Typical Concrete Footing Detail. 8) During construction, the site and all the material on it must be secured when unattendettx"rev t ch' n from playing on them. Do not leave decks with unprotected openings when unattended_-0-8t'rem orary - cades if necessary. r'1 X. 111��' 111 9) Install all other play components per the installation instructions. After all compponentk*ld ettolnsureg?e properly attached, pour the remaining concrete footings per the Typical Concrete Footing�etail. c.n N 10) Install protective surfacing material. 11) Attach play hardware such as 'D' rings and swing seats last, after protective surfacing is in place and footings have cured at least 3 days. 12) Carefully and thoroughly inspect the entire PlayBooster to be sure all fastening hardware is tight. According to ASTM F1487, section 6.2 sharpporTits, edgges and protrusions; any exposed bolt ends should not protrude beyond the face of the nut more than two (2) threads. This condition is not planned, but may exist in some applications because materials and finishes will vary. To remedy this situation, add a second nut or washer(s), extras have been added to the spare parts kit. See illustrations on reverse side of this sheet. Children should not be allowed on the structure until this inspection is complete. 13) Before children are allowed on the structure, the site must be cleaned and free of all construction debris and packaging material. Do not bum on the site. Pla Booster General Construction Guidelines Sheet 1 of 2 6017TH STREET SOUTH, DELANO, MINNESOTA 55328,8605 (763)972-3391 1-888-LSI-INST (1.888.5744678) FA%17631972-3185WA 01 landscape structures° Tools Required Tools required for installation are an auger, or other equipment for digging 14" diameter footing holes; shovels, rubber mallet, drill (with'/f','/,6', 9/16 , "/ I6" and Y." drill bits), tape measure, hex keys or allen wrenches, level, %" socket set, hammer, open end wrench set, screw driver, for surface mount a hammer drill,'/8" and '/2" masonry bits and transit or string line to aid in layout. Some washable felt tip pens are also useful for marking clamp locations. Materials Required All PlayBooster materials are supplied except concrete for footings, protective surfacing mate- rial, and curbing or edging material. With the exception of the special wrenches required (for the pinned hex fasteners) no other tools are supplied. Recycling Many of our packaging materials can be recycled, please take the time to separate and deliver them to a recycler. Thank You. Installation Times Installation times, as noted on the back of the installation sheets, are approximate and will vary depending on soil conditions, installer's equipment and ability. Times indicated do not include unloading or unpacking equipment. The man hours given are for one person installing (unless otherwise noted). Cut time in half for two people. Technical Services If you have any questions or concerns about the installation of your structure, call our Technical Services Department at: I-800-328-0035 (7:30 - 5:30p.m. CST/M-F). No Illustrations For Note 10, (Reverse Side Of This More Than Two (2) Threads Exposed Add Washers Installation Add Another Nut (Align FlatArea) 02001 by LaMscape Stmclures All lights reserved 1101 lk% luncol 11 141291Y) Pepl,­ 1ep19W_ pdarcd lrmalWtimu lmwtiia j & landscape structures, SAFETY NOTE Choose a protective surlaoiy material Nat has a Ctltiwl Heigh Valob of at least Ne height of Ne Highmt Accessible PaNFall Mepht of the aQxeN eguprnent. (Rel. ASTM 1.) Determine the highest accessible part - by definition. 2.) Determine the type of surfacing material desired: • Unitary - Bound rubber type materials for the accessible areas. • Loose -fill - Sand, wood chips, etc. for non -accessible areas. 3.) Select a material that has a Critical Height value of at least the height of the highest accessible part. • According to the CPSC, Critical Height is defined as the maximum height from which the instrumented metal headform, upon impact, yields both a peak decelera- tion of no more than 200 G's and a HIC value of no more than 1,000 when tested in accordance with the procedure described in the ASTM Test Method F 1292. • Reqquest independent laboratory test results showing the critical height of each product per the above procedures for commercially available products. The CPSC has tested some common loose -fill materials that are commonly not tested as a protective surfacing. (See back page.) 4.) Cover the designated use zone with the desired materials. If a different type of material is used for the accessible route of travel, make sure the surfaces are maintained flush. N _O ; Vl C-3 E ck r M Selecting Protective Surfacing for Your Playgt6und Sheet2of2 C 2001 by Lanascst a Stmctures An rights reg r� e Document #13412800 TOP OF GUARDRAIL OR HIGHEST PLATFORM WITH BARRIER PIVOT POINT HEIGHT OF \ HIGHEST PART TAKEOFF PLATFORM i SLIDES PLATFORM SWINGS CLIMBERSAND CLIMBERS HORIZONTAL LADDERS 1.) Determine the highest accessible part - by definition. 2.) Determine the type of surfacing material desired: • Unitary - Bound rubber type materials for the accessible areas. • Loose -fill - Sand, wood chips, etc. for non -accessible areas. 3.) Select a material that has a Critical Height value of at least the height of the highest accessible part. • According to the CPSC, Critical Height is defined as the maximum height from which the instrumented metal headform, upon impact, yields both a peak decelera- tion of no more than 200 G's and a HIC value of no more than 1,000 when tested in accordance with the procedure described in the ASTM Test Method F 1292. • Reqquest independent laboratory test results showing the critical height of each product per the above procedures for commercially available products. The CPSC has tested some common loose -fill materials that are commonly not tested as a protective surfacing. (See back page.) 4.) Cover the designated use zone with the desired materials. If a different type of material is used for the accessible route of travel, make sure the surfaces are maintained flush. N _O ; Vl C-3 E ck r M Selecting Protective Surfacing for Your Playgt6und Sheet2of2 C 2001 by Lanascst a Stmctures An rights reg r� e Document #13412800 I& landscape structures SAFETY NOTE Choose a Ixotectiva suRaarg m711=111211 Ms a Critical Height Value of eheight of Ne Highest AmesaiblHeightUn aQarenl elripthe l Ff19T.) Critical Heights (in Feet) NA = Not Available * NOTE: Compressed depths most accurately depict conditions on a playground. * An approximation of the maximum fall height from which a life-threatening head injury would not be expected to occur, based on tests in which a headform yielded both a peak deceleration of less than 200 G's and a RIC of less than 1000 upon impact. * Handbook for Public Playground Safety, published by the U.S. Consumer Prod- ucts Safety Commission, Section 10, Table 2, page 21. Critical Heiahts 0 2W1 by LaMscape Structures All nghts reserved Ei Ay Uncompressed Depth Compressed Depth Material 6" 9" 12" 9" * Wood Mulch ................................................ T IV 11'...............10' * Double Shredded Bark Mulch ...................... 6 IV I I'................ 7' * Uniform Wood Chips ................................... 6 7' 12 ................. 6' * Fine Sand ..................................................... 5' 5' 9'................ 5' * Coarse Sand ................................................. 5' 5' 6'................ 4' * Fine Gravel .................................................. 6 T 10'................6' * Medium Gravel ............................................ 5' 5' 6'................ 5' NA = Not Available * NOTE: Compressed depths most accurately depict conditions on a playground. * An approximation of the maximum fall height from which a life-threatening head injury would not be expected to occur, based on tests in which a headform yielded both a peak deceleration of less than 200 G's and a RIC of less than 1000 upon impact. * Handbook for Public Playground Safety, published by the U.S. Consumer Prod- ucts Safety Commission, Section 10, Table 2, page 21. Critical Heiahts 0 2W1 by LaMscape Structures All nghts reserved Ei Ay cn y nth C r A m �x a 9/& landscape structures° Q k; SAFETYNOTE Choose a prolective sudaorq material that nose Critical Heigh Value m at least the dhM height of the Highest Amessible ReNFell '�O® Cerlii'ieE F1,B7) iris agacent equpnrent lRef.ASiM 3-14-01 12026200 Arch 211"1530 Radius SPECIFICATIONS: Arch formed from 5" O.D. 6005-T5 alumi- num tubing with t/;' wall thickness. Unit is coated with a baked -on polyester powder - coating, color specified. Key: e.n O —4 Deck Height Dimension 32"/810 ............. 92 %'72350 40'71020 ............ 98 '1 48"/1220 ............ 90 1/2'/2299 56"1420 ............. 98 '/z"/2502 64"/1630 ............ 90 1/2"/2299 72"/1830 ............ 90 1/2"12299 At Grade (No Deck)... 97'/,"/2470 Dark NOTE: ==H Refer To Your Plan For Location Of Arches. 1070 Finished Grade pp M1 :9499[ Standard Concrete Footings Required w/ 347/860 Bury Arches IR771211 O tF I r' —i e.n O —4 r � rn = m 2} cn ry 1 ® toot by Landscape Structures All rights reserved 1 -w -In 1*1;4zsa0o Ml,a.,# 13317700, cman,•ai tul to axis-rs. Document#13433600 11-21.01 "How to distribute your hardware Headache Free" We have received feedback from you, our customers, that the most common delay in completing your playground installation is lost or misplaced hardware. Some of our most successful installations have used a "check- out" system with one person appointed to distribute the various hardware packages. Installation sheets are provided for each component that indicate hardware packages/items required to assemble that component. Refer to these sheets to determine which hardware items to request from the designated "check-out" person. HELPFUL HINTS: Read installation sheets. Be sure to use the correct length hardware as specifMd on the installation sheets. �^ Be sure to use clamps in the correct location 2ind}ptee-= on the installation sheets.,- n, M E -,c ,A 77 N Document#13701800 11-21-01 "How to distribute your hardware Headache Free" We have received feedback from you, our customers, that the most common delay in completing your playground installation is lost or misplaced hardware. Some of our most successful installations have used a "check- out" system with one person appointed to distribute the various hardware packages. Installation sheets are provided for each component that indicate hardware packages/items required to assemble that component. Refer to these sheets to determine which hardware items to request from the designated "check-out" person. HELPFUL HINTS: Read installation sheets. Be sure to use the correct length hardware as specified on the installation sheets. e Be sure to use clamps in the correct locatiotinHi0 cat on the installation sheets. r M C'— r rrn n. M rl y' t�J Document #13701800 j & landscape structurev Post Specifications: Post length shall vary depending upon the intended use and shall be a minimum of 42" above the deck height. All posts shall be powdercoaled to specified color. All posts shall have a "finished grade marker" positioned on the post iden- tifying the 34" bury line (or 44" bury line for posts for 96" decks) required for correct installation and the top of the loose fill pro- tective surfacing. Top caps for posts shall be aluminum die cast from 369.1 alloy and powdercoated to match the post color. All caps shall be factory installed and secured in place with (3) self sealing rivets. A molded low density polyethylene cap, with drain holes, shall be pressed onto the bottom end of the post to in- crease the footing area. Steel Posts: All steel PlayBooster posts are manufactured from 5" O.D. tubing with a wall thickness of .120" and shall be galva- nized after rolling and shall have both the I.D.and the cut ends sprayed with a corrosion resistant coating. Aluminum Posts: All aluminum PlayBooster posts are manufac- tured from 6005-T5 extruded tubing conforming to ASTM B-221. Posts shall have a 5" outside diameter with a .125" wall thick- ness. Finished Grade. Sticker LOQSE FILL PRQTECTIVE SIACING CONCRETE a:. • 1.87 Cubic Feet per Footing. - • 2000 PSI (Min.) • 3000 PSI (Min.) If Freezing Conditions Exist. Crushed Rock -- PlavBooster'' 1 11 CERTIFIED SAFETY NOTE Caaose a pMeceve nurletlrp material ttut Iru •Critical Heist Value of at leael Ore Might d Ne Highest AccessiNe PaNFall HeigN ohne a4.t equp ytM (Ref ASM F11B7) 13871600 Part Number Label Example 14" Minimum i—_ 360 Concrete Footin a "An Example: If you are using 12" of loose fill material, your concrete footing will be 22" deep. 5" Posts C 2002 by LarWscap Seucw,es All rights reservea l 1)om�ei,iaun7l(AX)<ph•Y•e114n7tn-1rem, edPad l<eeth srcke,. Document#13871600 kk landscape structuress warning Your playground may include equipment containing moving parts. Moving parts are more vulnerable to wear, mis-use and abuse than other non-moving parts. It is critical these parts be inspected and maintained according to our recommendations. As the owner, it is your responsibility to perform preventative maintenance and record your findings. Failure to do so may create a hazard and cause serious injury or death. 6017TH STREET SOUTH, P.O. BOX 198 DELANO, MINNESOTA 55328-0198 (763)972-3391 1-888-LSI-INS7 1.888.5744678) FAX (763) 972.3185 , Document01 N O 6� CJ1 � Imo{ i n / I 1 zy M a� cn N 6017TH STREET SOUTH, P.O. BOX 198 DELANO, MINNESOTA 55328-0198 (763)972-3391 1-888-LSI-INS7 1.888.5744678) FAX (763) 972.3185 , Document01 kk landscape structures, Wammog, Your playground may include equipment containing moving parts. Moving parts are more vulnerable to wear, mis-use and abuse than other non-moving parts. It is critical these parts be inspected and maintained according to our recommendations. As the owner, it is your responsibility to perform preventative maintenance and record your findings. Failure to do so may create a hazard and cause serious injury or death. N O Q ri. C-1) m v� s Cn N V2004 by Landscape swcwres All ngnts reserved , Document #14916800 According to the U.S. Consumer Product Safety Commission (CPSC) nearly 70% of all playground injuries are caused by falls to the surface. PLEASE INSTALL AND MAINTAIN ADEQUATE PROTECTIVE SURFACING UNDER AND AROUND YOUR PLAYSTRUCTURE! Never let children play on the equipment before protective surfacing is installed. Consult the CPSC's Handbook for Public Playground Safety, the ASTM F1487 Standard or your Landscape Structures representative—. for more information. 12 o v� _1 t M 3 (V� l0 landscape structures` PS/PB/FP/Evos/Weevos 7 2006 Document#15745100 According to the U.S. Consumer Product Safety Commission (CPSC) nearly 70% of all playground injuries are caused by falls to the surface. PLEASE INSTALL AND MAINTAIN ADEQUATE PROTECTIVE SURFACING FP UNDER AND AROUND YOUR PLAYSTRUCTURE! Never let children play on the equipment before protective surfacing is installed. Consult the CPSC's Handbook for Public Playground Safety, the ASTM F1487 Standard or your Landscape Structures representative for more information. _, U � C-1 o' �-m landscape structures` >1 rn N 7/12/2/6/5 2006 Document#15745100 U) LL 06 CL R 0 m CD co U c 0 JS CIO E E -F'F'F a U e q ��N LL x xxx y 43) LL Imo,, -1 N– NNNNNNNNNN�r RRRg��.�.b SQ'F WSO S4 SQ SO SR SQ��E3 � �Nj� ���� MO 0 �pSNC4�&��Oi O>msrNxXXXXXXXXXxXXXXXXMM XXoNoNNN�-qqqNYON 0X `^ a e-�^ �ry��VNN Nil t+l t•1M �^�^N x x x` x^ x xq x^ x x ^ AM 9* 53 !OWA N N N N N N N N N • r • r r • • r Vr-Vt+Ir���r NCpy Ol•-Nr-mN xxxxxx� In c;06Y) IN 1n"N --N N Oi 01� � 0) O)– � – a t FW. o mE�y = „ V y O cm d ro N N TN�0„ -a-aLL E ;dtE 9– OlX • r cc N 0 cc 9 m 0 is QL d W � CE$O E m .000 07 �L� w NaN N 0 CL mm 0 O O E c 4) °.00CL U = r ?. Q 3 10 U m�a� =.2 cc S V C Y r ti « o � O w C maw`° C W m y E>> EPrZ O v C C L = t ams agi�c$ .co;3 v ~ ac:; Lij.y0m moo .2 00,0 z3m_ Expansion Anchors (used To secure components To Concrete Slabs) C:f: Recommended Sizes Mat'I Torque Part # Inches mm or Grade Ftilbs Kgm 10C2630D '/,'x2'/i' (9,5x69,9) AlbySteel 15 2 10028800 '/2'x2'/i' (12,7x89,9) MbySteel 2) 28 Drtve Riveffi Sizes Part # Inches mm Mat'l 100609M '/;'x'/,,' BHCS w/Pin Limited Thread Bolts Akre RieVAkm Pin 0::3 '/�"X'/e" Recommended ALmRietS Ph Sizes Mat'I Torque Part # Inches mm or Grade FtAbs Kgm 10029DO0 '/e'x'/e' 52) ssiiTa 21 3 100292-00 '/,'x1'/;' 8)) SST�IT 21 3 15770100 1'9:5xx3'1. 7/,e"X2' 11,11x51 SSFFff 40 55 12706800 7/,,'x27/,,' 11,11X81,91) SSMAT 40 55 Lag Screws 10051300 '/4"x7/;' 6,4X22,2) Sizes Mat'[ Part # Inches mm or Grade Head Type 100127-00 141.x 1, p,9x31,8) SSf lex Head 16819800 '/,'x1'/=' (9,5x38,1) SST ButtonHead(Shmn 13903900 '/;'x2' (9,5x50,8) SST Button Head Shovm Screw, Type AB Thread BHCS w/Pin call", Mat'] Part # Size or Grade 129571-00 #14x'/;' SST 127872-00 #14x'/4'' SST 136232-00 #14x1" SST 129872-00 #140'/;' SST Expansion Anchors (used To secure components To Concrete Slabs) C:f: Recommended Sizes Mat'I Torque Part # Inches mm or Grade Ftilbs Kgm 10C2630D '/,'x2'/i' (9,5x69,9) AlbySteel 15 2 10028800 '/2'x2'/i' (12,7x89,9) MbySteel 2) 28 Drtve Riveffi Sizes Part # Inches mm Mat'l 100609M '/;'x'/,,' 6,4x4,8 Akre RieVAkm Pin 1O0611 -0D '/�"X'/e" 6,4x9,5 ALmRietS Ph 11330DOO '/4"X'/2" 6,4x12, AkrnRheMinPin 1O061O4M '/4"x'/e" 6,4x15,9 AkxnRi.RVSSTPn 139152-00 /4.X'/;' 6,4x19, ) A rnRiiNAkmPin 10051300 '/4"x7/;' 6,4X22,2) MrnRieVAkmPn 11815600 '/;'x1" 6,4x25,4) Alun Ri" Akm Pin Low Crown Cap Nut Size Inches %"-16UNC N G 0 O n-< i �C :<r,i a a o Mall' rn g �\ B , � - k\ j) I}�z�zr}z1 §Kgs §§)§' E§§A WAR $ E $ � \ � ® | ci c E _ CO) 7 \§k \ B H $5) g �\ B , � - k\ j) I}�z�zr}z1 §Kgs §§)§' E§§A WAR ME §/ E $ ® / \§§2 E 2 ME WIN §/ E $ ® E § \§k � B H $5) WIN m c § §/ $ ® E \§k B H $5) cq •. 7\ x� � a z m c § Set Screw Size Mat'1 Part# Inches ® orGraile 10029600 3/e"X'/,." (9,5X11,1) SST Bolt Link Part # Double Clevis Mat'I or Grade IR Offset Hanger Clamp (PlayBooster) Part # Mael 11372800 Ca4AArrism Half Clamp (PlayBooster) Part # Mat'I 105327-01 CsAAUnrun� 0 p 0 "ems Deck Hanger Clamp (PlayBoc;ii— ::;n r _crrn- fT`i o S C) Mat'I Pato # or Grade Part # Mat'l 138917-00 SST 106022M CaSiAtriY%rrl A& landscape structures* Swing Hanger Clamp Part # Mat'I 121219M CastAk i Ring/Rail Hanger Clamp (Playsooster) am 1. CI 11 1 CastAluminum 1 1 1 CERTIFIED Offset Bolt Bracket (Playshaper) b Part # Hex -Pin Allen Wrench Mat'I Hex -Pin Drlwr Part# Description 10068640 Flex-inAllenWench 100695M Hex-P1nDmer(Used VNthASI,_='Socket) 6 -Lobe Wrench -M 6 -Lobe Driver N O Cf1 C-,) u.�m �-�jr,r m :�Iorx pjn Driver Part # Description 146017-00 6{abeWerxh(T45) 146007-00 64.obeDrier -05 (UsedMA51,a'Socket) 127463-10 Tax4)nDiver(T-27)(LWWtliAY4'SodBt) Sheet 3 of 3 Document #16338900 Eco#537N pcuvwnt#16338M "lace 01W"k U&tl Fatenen k4-1. landscape structures INCH mm HOW TO DETERMINE BOLT LENGTHS Example shows a 1 '/," long plow bolt. Measurement method also applies to flathead cap screws. Example shows a 1 '/," long BH cap screw. Measurement method also applies to hex cap screws, limited thread bolts, lag screws and carriage bolts. Rule: Measurements should be based on the part of the screw that penetrates the surface. 0 N � �...t an O C-) =r n rn rn X. rn m o a/& landscape structures® ;wIqq ctl:ririeoim Common Parts & Fasteners Button Head Cap Screws BHCS w/Pin 05DRecommended Sizes Mat'] Torque Part # Inches nun or Grade F[./lbs Kgm 137277-00 '/;'x%" (6,4x9,5) SSTTPT 10 14 131849W '/,;'x'/,'(7,9x12,7) SSTTPT 10 1.4 13262600 1/,8'X7/e" 9x22,2 SST -W �8x24mm 10 1.4 195071-00 3/1'. X11/i' SSTAV 10 1.4 10019.500 %"x'/;' (9,5x15,9) SST -FAT 15 2 1001960D/8''X7/e' (((9,5x31,8) 9,5x44,5) 9,5x22,2 1 Ur 2 10019600 °la'X1'/1" 9,5x28,6 SST -PAT 15 2 113077-00 '/e 1X 1'/e" 9,5x34,9 SSi�7CT 15 2 100171-00 'l;'x1It," 9,5x38,1 SSTfl4T 15 2 12322400 1/8'x1"/,s' 9,5x42,9 SST -RV 15 2 10017300 1/;'x2" 9,5x50,8 ssrFAT 15 2 10019900 %"x21/,' 9,5x57,2 SSMAT 15 2 10017400 %"x21/2' 9,5x63,5) SST -FAT 15 2 10017500 %"x21/;' 9,5x69,9) SSMAT 15 2 1D0176M '/e11x3" 9,5x76,2) SST -RV 15 2 10016600 %"x31/i' 9,5x82,6) SST -W 15 2 10020000 '/;'x3'1,' 9,5x88,9) SSTPAT 15 2 12446100 1/e'x31/;' 9,5x95,2) SST -FU 15 2 100201-00 5/;'x1'/2' 15,9x38,1) SST -W 5) 7 127551M 5/;1x1'/z' 15,9x38,1) SST 5) 7 ANTI-SIEZE 100203-00 5/5''x2'/4' (15,9x57,2) SST -PAT 5) 7 Hex Cap Screws Recommended Sizes Mat'] Torque Part # Inches mm or Grade Ft./lbs Kgm 10020600 1/8'x1" (9,5x25,4 SSMAT 15 2 10020600 1/;1x1'/i' (9,5x38,1 SSMAT 15 2 10020900 %"x11/;' (9,5x44,4 SST -W 15 2 135682-00 1/;1x3'/;' (9,5x79,3 SST -PAT 15 2 13568300 %"x45/;' (9,5x117,5) SST 15 2 100214-0D 1/;'x5" 9,5027) SSTRV 15 2 12149300 7118'x 13/4' 11, t x 114,3) SST -PAT 15 2 100216M '/,'x111;' 12,7x31,7) SST 15 2 131862M 1/,'x2'/;' 12,7x57,1) SST -FAT M 28 Carriage Bolts Recommended Flat Head Cap Screws (FHCS) No Pin* With Pin 6:ZD 6E]JI Sizes Mat'l Torque Part # Inches mm or Grade FtAbs Kgm 100135400 5/,;1x1'/;' (7,9x31,8) SSTTAT 5 07 100147-00 1/;'x1'/;' 3/1'. X11/i' SSMAT 15 2 116017-00 1/;'x1'/1' 9,5x38,1) SSr-FAT 15 2 10014800 3/e'x1'l;' (((9,5x31,8) 9,5x44,5) SST -PAT 15 2 Flat Head Cap Screws (FHCS) No Pin* With Pin 6:ZD 6E]JI NOTE: These are recommended torque applications per fastener size. When fasteners are used with plastic or wood products, the torque specifications will be excessive and we recommend that the installer apply some caution when tightening the fasteners. Plastic or wood products should begin to deform slightly. Fasteners indicated with :"Pat" Includes a locking patch type material and should cure for 72 hours for maximum strength. 1� #16338900 Recommended Size Mat'l Torque Part # Inches mm or Grade Ft./lbs Kgm 148686M 3/8'x1/;' 9,5x19,05) SSWAT 13 18 104452-00' 3/1'. X11/i' 9,5xSSMT 13 1.8 15148767654M 11 ��°�„z31/2” T 9'Sz�T 112,51k, 18 ] 18 11,'x2'/," '--"®A 28 13082400' SSI1 n—< m t Cr— rn M NOTE: These are recommended torque applications per fastener size. When fasteners are used with plastic or wood products, the torque specifications will be excessive and we recommend that the installer apply some caution when tightening the fasteners. Plastic or wood products should begin to deform slightly. Fasteners indicated with :"Pat" Includes a locking patch type material and should cure for 72 hours for maximum strength. 1� #16338900 BHCS w/Pin Limited Thread Bolts L1101111 Sizes Mat'] Torque Part # Inches mm or Grade Ft./lbs Kgm 10O29OM 3/a"X71a" 9,5x22,2 SST -PAT 21 3 100292-00 a/e'x1'/�' 9,5x318)) SSMV 21 3 15770400 7/,;'x2" 11,11x51) SsrPM 4) 55 127068-00 7/,;'x27/,8' 111,11)61,91) SSMAT 4) 55 Lag Screws r Air '111 Recommended so Screw, Type AB Thread BHCS w/Pin Part # M Size Mat'] or Grade 129671-00 #14x1/2' SST 127MM #14x3/4' SST 136232-00 #14x1" SST 129672-00 #140'/4' SST Expansion Anchors (Used To Secure Components To Concrete Slabs) Recommended Sizes Mat'l Torque Part # Inches mm or Grade FtAbs Kgm 10026300 3!8'x23/;'(9,5x69,9) AloySted 15 2 10026600 1!,'x23/4' (12,7x69,9) AlaySteel 2l 28 Drive Rivets Gr n9th Sizes Mat'l Part # Inches nun or Grade Head Type 100127-00 '/,8'x1'/;' ,9x31,8) SST Hex Head 16919800 3/8'x11/,' 9,5x38,1) SST Button Head((Shawn) 1390390 0 x2" % 9,5x50,8) SST BuftonHead (Shawn) Screw, Type AB Thread BHCS w/Pin Part # M Size Mat'] or Grade 129671-00 #14x1/2' SST 127MM #14x3/4' SST 136232-00 #14x1" SST 129672-00 #140'/4' SST Expansion Anchors (Used To Secure Components To Concrete Slabs) Recommended Sizes Mat'l Torque Part # Inches mm or Grade FtAbs Kgm 10026300 3!8'x23/;'(9,5x69,9) AloySted 15 2 10026600 1!,'x23/4' (12,7x69,9) AlaySteel 2l 28 Drive Rivets Gr n9th Size Part # Inches Mat'] 100349-00 3/8'-16UNC SST Sizes Part # Inches mm Mat'l 10060900 '/4'x3/,8' (6,4x4,8) AkmRK,9VAkmPn 100511-00 '/8'XV AkmRiveGSSTPn 11330O0D '/;'x'/,' ((6,4x9,5) 6,4x12,7) Alum RNeVA1um Pn 10061000 /4. %. (6,4x15,9) AlunRhEUSSTPn 139152-00 3/;'x3/;' Alum RkeYAkm Pn 10051340 '/;'x7/8' 6,4x22,2) Alum Rivd/Akm Pin 11815800 '/43x1" 4((6,4x19,05) 6,4x25,4) Alun RiVet/Alun Pin Low Crown Cap Nut ..., C"—+ c"s-C 1 r —1 n rn fir— M o >, o Cr Size Part # Inches Mat'] 100349-00 3/8'-16UNC SST A& landscape structures' Standard Hex Nuts (S) Sizes Mat'1 Part # Inches or Grade 100326,00 si,,18UJC SST 100321-00 '/,16UJC SSMA 100327-00 '/,16LW SST 128295M '/,16UNC(JamNut) SST 100328,00 'I„ 14UNC SST 145021-00 '/a-14UNC(JamNut) SST 100322-00 '/,13UNC SST 129N2-00 '/%-13UNC SS -M& 12969300 '/2-13UNC (Jam Nut) SST 10002300 %-11 UNC SST Flange Nut w/Pin Sizes Mat'l Part# Inches or Grade 19206400 M8x24mn SST 10035300 3/,16UNC SST Flat Washers 1.1 Part # Sizes Inches nun or Grade I.D. O.D. 12203900 '/4' (6,3) SST 0.312 .734 100362-00 3/8' (9,5) SST 0.406 1.002 11279300 '/,;'11,1 / SST 0.506 126'2 100063-00 '/2' 1273 SST 0.535 1232 100396-M '/e' 15,9) SST 0.B6 1.750 123737-00 11/e' ,6) SST 1.140 1.750 ISO ctfiliciEo Curved Spring Washer Sizes Mail Part# Inches mm or Grade I.D. O.D. 10038D00 1/2.' (12,7) SST 0.531 0.795 SAE Flat Washers Sizes Mat'1 Part # Inches mm or Grade I.D. O.D. 10036400 '/i' ((6,35) SSr 0281 0.625 100365430 '/e' (9,5) SST 0.411 0.816 11355000 12' (12,7) SST 0531 1.062 1295COW s/a' (15,9) SST 0.666 1.342 Fender Washers IN Sizes G". Ng'] ^2 RIO. Part # Inches or F Cade O.D. 100378-00 '/;'x1'/z' (9,� w ..W1G6 1.500 10037900 '/,'x2" (12, M 10.531 2000 Tee Nut (PlayBooster Clarpmk, ,tl 1 c.n / Sizes Mail Part # Inches or Grade 100351-00 '/,16UNC SST Sheet 2 of 3 Document #16338900 a& landscape structures, Set Screw Sizes Mat'1 Part # Inches mm or Grade 10Ce9800 '/e'x'/1a' (9,5x11,1) SST Bolt Link Mat'1 Part # or Grade 13E8.1500 SSr Double Clevis Part # 131817-00 Mat'1 or Grade N Offset Hanger Clamp (Play600ster) Part # Mat'1 11372900 CaA krrwi m Half Clamp (Playsooster) Part 4 Mat'I 105327-01 CastAkmtrxm N c� fJl Deck Hanger Clamp (Playsoosj -- �� a f 0 Z5 CD Part # Mat'1 A& landscape structures* Swing Hanger Clamp Part # Mad 12128900 Caslaurtlun Ring/Rail Hanger Clamp (Playsooster) EM nsai CaMumin rn cEarrFlEo Offset Bolt Bracket (Playshaper) 0 Part # Mat'1 CasfMrrinun Hex -Pin Allen Wrench Hex -Pin Driver Part # Description 10068500 Flex-PnAllenWrench 100685M Heat-PinDnver(UsedWthA'/,;'Socket) 6 -Lobe Wrench MM 6 -Lobe Driver Torx-Mn Driver Part # N L� 146017-00 &LobbeWench(T-45) 146007-00 6-LobeDrkw(T-05)(UsedWthA51,,'Socket) 12746300 Tkxx4inDrivw f-2 (Used MA1/i'Socket) c') r O Torx-Mn Driver Part # Description 146017-00 &LobbeWench(T-45) 146007-00 6-LobeDrkw(T-05)(UsedWthA51,,'Socket) 12746300 Tkxx4inDrivw f-2 (Used MA1/i'Socket) Sheet 3 of 3 Document#16338900 F 0537WD ml#1633$Mmlec #IU36 Udated Futenen. lk landscape structures, 1 INCH 1 HOW TO DETERMINE BOLT LENGTHS Example shows a 1 '/," long plow bolt. Measurement method also applies to flathead cap screws. Example shows a 1 '/;' long BH cap screw. Measurement method also applies to hex cap screws, limited thread bolts, lag screws and carriage bolts. 2 3 4 Rule: Measurements should be based on the part of the screw that penetrates the surface. 5' 6 1 •- N O_ r CJ9 .' CCS O zin � r ;<r a rn _m o o Did you know that most of the packaging materials you receive on a Landscape Structures order are recyclable? Do you reuse or recycle everything you can from your playground sites? We're making it easier for you to do the right thing and keep these materials out of landfills! FOAM/SCRIM SHEETS Landscape Structures has partnered with our supplier to recycle foam/scrim material, the grey and white sheets that are layered between the large painted parts. This material is not usually accepted at general recycling facilities but this supplier will re -use it in their manufacturing of new packaging materials. It's easy! Just put the foam/scrim from your installation site in a box and ship it to the facility closest to you. Here is a list of participating facilities throughout the U.S.: Foam/Scrim Products Only Pregis Plant 159 N San Antonio Ave. Pomona, CA 91767 Pregis Plant 8201 W Elowin Ct. Visalia, CA 93291 Pregis Plant 7574 Presidents Dr. Orlando, FL 32809 Pregis Plant 3825 N Main St. Granite Falls, NC 28630 Pregis Plant 18 Peck Ave. Glens Falls, NY 12801 Pregis Plant 3500 S Highway 287 Corsicana, TX 75109 Foam/Scrim, Plastic Banding, Shrink Wrap Anchor Facility 480 Broadway St. St Paul, MN 55101 Anchor Facility 1501 Swasey Rd. Hudson, WI 54016 Pregis Plant Pregis Plant 1411 Pidco Dr. 310 Old Station Rd. Plymouth, IN 46563 Wenatchee, WA 98801 N Pregis Plant --1 R _ 300 Harris Rd. c'r4 I Wurtland, KY 41144 .Gm a M Don't stop here! Most of the other packaging materials can also be recycled, reused of 7pu poed. CJ9 • CORRUGATED CARDBOARD: Boxes can be broken down and recycled at a local recycler, or reus6d for other storage. • SHRINK WRAP: Contact your local plastic recycler and ask if they accept polyethylene plastic. • PLASTIC BANDING: Contact your local plastic recycler and ask if they accept polypropylene. If you have suggestions for recycling, reusing or repurposing other materials, please email them to: info@playlsi.com. Just one more way Landscape Structures is building healthy, sustainable communities. #16604400 182212 is an entanglement label Not an Install doc. cn w 182213 is a hot surface label Not an Install doc. N IE D- O �� Q1 r <r -- m �_ M w D cn I?, landscape structures' Look for compliance to the following guidelines and standards whenever you install playground equipment. It's your assurance that the products you install meet the most rigorous safety and quality assurance standards. Landscape Structures is a member in good standing of IPEMA, the International Play Equipment Manufacturers Association. IPEMA is a member - driven, international trade organization that represents and promotes an open market for manufacturers of play equipment. l(UIPEMA MEMBER In the interest of playground safety, IPEMA provides a Third Party Certification Service whereby a designated independent laboratory validates a participant's certification of conformance to ASTM F1487, Standard Consumer Safety Performance Specification for Playground Equipment for Public Use, except sections 7.1.1, 10 and 12.6.1; CAN/CSA Z614, Children's Playspaces and Equipment Standards, except clauses 9.8, 10 and 11; or both. The use of the corresponding logo in the Landscape Structures Inc. catalog signifies that Landscape Structures Inc. has received written validation from the independent laboratory that the product(s) associated with the use of the logo conforms with the requirements of the indicated standards. Check the IPEMA website (www.ipema.org) to confirm product certification. The use zone and fall height requirements in this publication are shown to ASTM standards. The requirements for other standards may be different. According to the CSA, playground maintenance and inspection is a continuous and integral part of budgetary costs. The cost of inspection and maintenance shall be considered and incorporated into the budget at the time of design, purchase equipment and installation (11.1.1 Budgeting). The Consumer Product Safety Commission (CPSC) is a governmental organization that provides technical safety guidelines for designing, constructing, operating and maintaining public playgrounds. U.S. Consumer Product Safety Commission 4330 East West Hwy. Bethesda, MD 20814 www.cpsc.gov The American Society for Testing and Materials (ASTM) is a scientific and technical organization that is a major developer of standards for testing different types of materials. In 1993, the ASTM published "Standard Consumer Safety Performance Specifications for Playground Equipment for Public Use," designation F1487-93. ASTM is more technical than the CPSC. ASTM revised its old standard and published a new standard in 1995, 1998, 2001, 2005, 2007 and again in 2011. American Society for Testing &,8and Materials 100 Barr Harbor Dr. P.O. Box C700 u' West Conshohocken, PA 19428 www.astirl The Canadian Standards Association Nearly all equipment developed by Landscape Structures is certified to meet CAN/CSA-Z614-07, the Children's Playspaces and Equipment Standard, through IPEMA. The European Standard was developed by the European Committee for Standardization. The majority of Landscape Structures products have been designed to beTUV certified by a third -party validator to EN 1176: 2008, the European Standard for Playground Equipment. .01011k ISO 9001:2008 has a pro International Play Equipment Manufacturers customer focused and emphasizE��inti,16us r Association improvement in quality. �Grn M 4305 N. Sixth St. Suite A Harrisburg, PA 17110+- 0 www.ipema.org w, "' ,°•o• Y 11.11.d IPEMA ISO 14001:2004 drives us toward operatinitt a CERTIFIED CERTIFIED manner that is environmentally conscious. ASTM ASTM t` F7487 Ayna ISO 14001 PSTB/FNEvos/Weevos Guidelines & Standards 601 7TH STREET SOUTH, DELANO MINNESOTA 5532B-8605 (763)972-3391 1-888-1-SHNST (1-888-574-4678) FAX (763)972-3185 0 2012 by Landscape Structures. All rights resemd. Eco #54540 Document 18482200 replaces 15749200. Updated document. Document#18482200 I& landscape structures Look for compliance to the following guidelines and standards whenever you install playground equipment. It's your assurance that the products you install meet the most rigorous safety and quality assurance standards. Landscape Structures is a member in good standing of IPEMA, the International Play Equipment Manufacturers Association. IPEMA is a member - driven, international trade organization that represents and promotes an open market for manufacturers of play equipment. 1(4 IPEMA MEMBER In the interest of playground safety, IPEMA provides a Third Party Certification Service whereby a designated independent laboratory validates a participant's certification of conformance to ASTM F1487, Standard Consumer Safety Performance Specification for Playground Equipment for Public Use, except sections 7.1.1, 10 and 12.6.1; CAN/CSA Z614, Children's Playspaces and Equipment Standards, except clauses 9.8, 10 and 11; or both. The use of the corresponding logo in the Landscape Structures Inc. catalog signifies that Landscape Structures Inc. has received written validation from the independent laboratory that the product(s) associated with the use of the logo conforms with the requirements of the indicated standards. Check the IPEMA website (www.ipema.org) to confirm product certification. The use zone and fall height requirements in this publication are shown to ASTM standards. The requirements for other standards may be different. According to the CSA, playground maintenance and inspection is a continuous and integral part of budgetary costs. The cost of inspection and maintenance shall be considered and incorporated into the budget at the time of design, purchase equipment and installation (11.1.1 Budgeting). The Consumer Product Safety Commission (CPSC) is a governmental organization that provides technical safety guidelines for designing, constructing, operating and maintaining public playgrounds. U.S. Consumer Product Safety Commission 4330 East West Hwy. Bethesda, MD 20814 www.cpsc.gov The American Society for Testing and Materials (ASTM) is a scientific and technical organization that is a major developer of standards for testing different types of materials. In 1993, the ASTM published "Standard Consumer Safety Performance Specifications for Playground Equipment for Public Use," designation F1487-93. ASTM is more technical than the CPSC. ASTM revised its old standard and published a new standard in 1995, 1998, 2001, 2005, 2007 and again in 2011. International Play Equipment Manufacturers Association 4305 N. Sixth St. Suite A Harrisburg, PA 17110 www.ipema.org _ r'"•r`0µ'•.,- ,•°`•"•,"". �IPEMa 'sIPEM/I` CERTIFIED CERTIFIED A6TM ASTM Ft487 Rtatl7d , American Society for Testing and Materiels 100 Barr Harbor Dr. P.O. Box C700 *U1 West Conshohocken, PA 19428 www.astm.org The Canadian Standards Association Nearly all equipment developed by Landscape Structures is certified to meet CAN/CSA-Z614-07, the Children's Playspaces and Equipment Standard, through IPEMA. The European Standard was developed by the European Committee for Standardization. The majority of Landscape Structures products have been designed to be TUV certified by a third -party validator to EN 1176: 2008, the European Standard for Playground Equipment. ISO 9001:2008 has a process -orientated structuWis customer focused and emphasizeL=ontinq�us improvement in quality. �c ISO 14001:2004 drives us toward gpit ng to manner that is environmentally consci�:`-^a �-' 1 r .rA CEiitir i[o, PS/PB/FP/Evos/Weevos Guidelines & Standards 0 2012 by Landscape Structures. An lights reserved. Eco #54540 Document 18482200 replaces 15749200. Updated document DOCUment#18482200 S & landscape structures Typical Offset Hanger Clamp Assemble '/e' x 2 BHCS i I I I I I I I I %"x 2'/;' BHCS w/Pin (! 1 E; C E F T I i l E 0 Typical Handloop SAFE7Y NOTE Clause a polecLva sutlaorg material that las a Cntiwl Height Value of at least NB Wight of the Il ghter, ssible PaNFall Heigflldlneedjacenl equipment (Ref, ASTM Ff4a7.) 10971300 I I � 0 0 I c y I I _ I I o U c � N N I U i I I Typical Deck (32" Shown) r __ I � I Ooo am I I Q (✓) � LD cif lV O w O C—) 1 r n m <m a M _yam -0 cn 32" Deck - Use "ails (Shown) 40" Deck - Use 3 Rails 40'/,s" Rail Rail/Handl 9 Assembl 0 2013 by Landscape structures. All ngh,s reserved. Document #19437600 JU& landscape structures' J \SPECSM4119437600. P65 Parts List PlayBooster° Rail/Handloop Assembly Part# Description Qty- ty.111275-00 111275-00 Handloop Assembly ................................................. 1 108542-00 Handloop, Specify Color ........................................... 1 100198-00 3/e" x I '/i' BRCS w/Pin, SST ................................... 4 100203-00 '/s" x 2 1l4" BHCS w/Pin, SST ................................... 2 100351.00 3/e" Tee Nut, SST ........................................................ 4 100610-00 '/s" x %" Drive Rivet, SST ....................................... 2 105327-01 5" Half Clamp, Specify Color .................................. 2 113729-00 Offset Hanger Clamp, Specify Color ....................... 2 111276-00 Rail Assembly............................................................ 1 108569-00 Rail, Specify Color .................................................... 1 100198.00 3/,' x I '/s" BHCS w/Pin, SST ................................... 4 100203-00 '/a' x 2 '/i' BHCS w/Pin, SST ................................... 2 100351-00 '/s" Tee Nut, SST ........................................................ 4 100610-00 '/4" x'/s" Drive Rivet, SST ....................................... 2 105327-01 5" Half Clamp, Specify Color .................................. 2 113729-00 Offset Hanger Clamp, Specify Color ....................... 2 SDecifications I landloop: Weldment comprised of 1.125' O.D. 11 GA (.120") steel tubing with 203 or 303 stainless steel inserts, with '/,'internal thread.Finish: Tenderfufru,color speci- fied. Rail: Weldment comprised of 1.125" O.D. I I GA (.120") steel tubing with 203 or 303 stainless steel inserts, with '/r" internal thread. Finish: Tenderfuff' , color speci- fied. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShieldo, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproofin design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific pmd- act installation/specifications). Installation Time: Approx.%manhour Weight: 111275-00 (One) 11 lbs. 111276-00 (One) l l lbs. Installation Instructions 1) Mark locations of clamps on posts per dimensions on front of sheet 2) Attach offset clamps to ends of rails/handloops using 3/s" x 2'/4" BRCS w/pin. 3) Position rail/handloop on marked position on posts and attach using 5" half clamps and'/s" x 1 t/s" BHCS w/pin with'/." tee nuts. Refer to the Typical Offset Hanger Clamp Assembly Sheet. 4) Install drive rivets in half clamps per the Typical Offset Hanger Clamp Assembly Sheet. 5) Install protective surfacing before users are allowed to play on the structure. rros54sar D« t#1%37emn a142493M.Am mita bly r iri efia s. N O n C.n CD C --y ° 7 O r rros54sar D« t#1%37emn a142493M.Am mita bly r iri efia s. OWN landscape structuresm. SAFET'NOTE Choose a prolective svtadrg material nal tidy a Cnlical Meiphl V.lue M al I.dSt me height of Ne Hlylrest Accsaiwa ParVFall Heghl otme aejaoerdeWwrlenL (Ref ASTM F148T.) AWARNING Oravrstdngs have AWARNING entangled on slides tM lx•wd.aa has Thu, elaPlmclun and other playground — fall yyMe wthaNM �tWre,alme IW head ae3lgnee : 2 to 12 years ole aaalMkq «pro. de fir children equipment causing an., rpmraauwn tlgs ed.lpm.d + 6 to 23 months old strangulation, REMOVE Z7 0 And, her[,ent nnroMell. radon- and rae.aas usan helmet, drmastrings, tel rem.•aaidew:..... re. a„e ,,, 6to lz vena old. to have stool nt sa,tlrt.rcnW h WPe in had. ++aeon scarves and other same,and e.-h.ar 5treneln.de edo,dlnenu^. YetaataM3lan dragon antl neck priors playinround g sNa,NwWMnnu ^nr.aT+."tlrevl �"er^��'"'"tlie ea.tlinsireedden Adult •ul»rvined neck prior to PlaYin9 on n�W #rumor thatrWat.d.e`rn. Y�.r�...lxed Wemrea. the playground. wapVwu.eatnaaa. ... ./i, .rrat. -" 2 w h Part No. 156546-00-000 Part No. 156848-00-000 Part No. 166751-00-000 Part No. 182212-00-000 Part No. 183064-00-000 4 Trus plry31nw4mneragre4bR,Men ths paryou "e n deiprod m, e,.Mre^ .. TM1s geyabuCeaaw Geegred r rimier Tall Pai7ia. Maa oxy, me. a aurae. 2 to 5 Ygar• oltl 2 to 12 year. old 5 to 12 Ywn old b•Iw+ rN e^O reynres uamblw sreed�e And reer.aaa ubrs in herrn-11inu any 704 ogre to lNW sunenml 21ay Wllrinq. al,r:,glh y,dlttN„ayV• use's", aT.Srgh;nryq ract Ttla Rtlurl to I on Inc. Adult 3uperrlsmn a bong,, reAduX wParvlceapYpr,enln parvo uau e m..... (d pmc0.ders1 - angryrecommeMeeto l . causeenahwgtbn ♦beyaan old. ttW.en ur.•anri5yah, tae�ria 0aer4at6 timer A.....rl.brr n.+lll rr�ir�la�rrn Arer.are.+�,aa al Part No. 156850-00.000 Part No. 166815-00-000 The playatr,rc,.,< Ms rated ae5gned M ehlldran 5 to 12 years old Md ohn i005 is to MW •Wnclenl atungN add <oordlnation. Aon WParid". MIMgn Iacdndranded. All iiiie"i— 'N' n"" r' ­ that toren dr ,;nrrd (or children 2 to 5 years old and! own. . to haW •uniceant strength add coordination Adult sugarYl•lon r .,rid, ..a~.._ Part No. 200331-00-000 Part No. 200332-00.000 Part No. 200333-00-000 0 NOTE: The Playstructure desigi dentacsnine .- - whichPlay It Safe sticker will be supplied: INSTRUCTIONS: Surface must be clean and dry pnorto apply stick Peel back- ing sheet away from back of stickerdg11� pl��e stickei`in position. Using backing sheet, rub over face itf sticke'f�o burnish down into place. Choose a location visible to adults in *0bnspicuous location on product. Stickers work best on painted parts. Where possible, avoid placing on rotationally -molded plastic parts, TenderTuff-coated parts or where children may step and wear off sticker. This applies to both Freestanding Play items and Composite Playstructures. Apply sticker adjacent to or visible from the primary entrance to the structure. Apply 4'-5' above the surface. Apply at least (1) one to every structure and (2) two to large Composite Playstructures. Part No. 156847-00-000 Part No. 156845-00-000 PB/PS/FP/Evos®/Weevos® Warnina Labels 02014 by Lantlscape Structures. All rights reserved Fm 401 M8]Drrumanl#]0151300 rtplaes N 1 83066(1 Added (3) warning l.bels. Document Tni• PYSr,`L has been desitil AWARNING AWARNING I-erld<^ 2 to 3 years old O Installation over a and readier,.sara o Surfacing and playsurlaus - v - hard surface such = tnM.<s.nKlem may become H07 an0 >'D as concrete, asphalt, = s4.dgth am coo,eidallw. cause bums. Check for hot or packed earth may Add;udarrhil surfaces pnw to playing result in serious injury ag,; ad on the playground. or death from falls. - ^ a•aurra wa.r� �64 2 +Ij 64 Part No. 182213-00-000 Part No. 115176-00-000 Part No. 156844-00-000 AWARNING Oravrstdngs have AWARNING entangled on slides tM lx•wd.aa has Thu, elaPlmclun and other playground — fall yyMe wthaNM �tWre,alme IW head ae3lgnee : 2 to 12 years ole aaalMkq «pro. de fir children equipment causing an., rpmraauwn tlgs ed.lpm.d + 6 to 23 months old strangulation, REMOVE Z7 0 And, her[,ent nnroMell. radon- and rae.aas usan helmet, drmastrings, tel rem.•aaidew:..... re. a„e ,,, 6to lz vena old. to have stool nt sa,tlrt.rcnW h WPe in had. ++aeon scarves and other same,and e.-h.ar 5treneln.de edo,dlnenu^. YetaataM3lan dragon antl neck priors playinround g sNa,NwWMnnu ^nr.aT+."tlrevl �"er^��'"'"tlie ea.tlinsireedden Adult •ul»rvined neck prior to PlaYin9 on n�W #rumor thatrWat.d.e`rn. Y�.r�...lxed Wemrea. the playground. wapVwu.eatnaaa. ... ./i, .rrat. -" 2 w h Part No. 156546-00-000 Part No. 156848-00-000 Part No. 166751-00-000 Part No. 182212-00-000 Part No. 183064-00-000 4 Trus plry31nw4mneragre4bR,Men ths paryou "e n deiprod m, e,.Mre^ .. TM1s geyabuCeaaw Geegred r rimier Tall Pai7ia. Maa oxy, me. a aurae. 2 to 5 Ygar• oltl 2 to 12 year. old 5 to 12 Ywn old b•Iw+ rN e^O reynres uamblw sreed�e And reer.aaa ubrs in herrn-11inu any 704 ogre to lNW sunenml 21ay Wllrinq. al,r:,glh y,dlttN„ayV• use's", aT.Srgh;nryq ract Ttla Rtlurl to I on Inc. Adult 3uperrlsmn a bong,, reAduX wParvlceapYpr,enln parvo uau e m..... (d pmc0.ders1 - angryrecommeMeeto l . causeenahwgtbn ♦beyaan old. ttW.en ur.•anri5yah, tae�ria 0aer4at6 timer A.....rl.brr n.+lll rr�ir�la�rrn Arer.are.+�,aa al Part No. 156850-00.000 Part No. 166815-00-000 The playatr,rc,.,< Ms rated ae5gned M ehlldran 5 to 12 years old Md ohn i005 is to MW •Wnclenl atungN add <oordlnation. Aon WParid". MIMgn Iacdndranded. All iiiie"i— 'N' n"" r' ­ that toren dr ,;nrrd (or children 2 to 5 years old and! own. . to haW •uniceant strength add coordination Adult sugarYl•lon r .,rid, ..a~.._ Part No. 200331-00-000 Part No. 200332-00.000 Part No. 200333-00-000 0 NOTE: The Playstructure desigi dentacsnine .- - whichPlay It Safe sticker will be supplied: INSTRUCTIONS: Surface must be clean and dry pnorto apply stick Peel back- ing sheet away from back of stickerdg11� pl��e stickei`in position. Using backing sheet, rub over face itf sticke'f�o burnish down into place. Choose a location visible to adults in *0bnspicuous location on product. Stickers work best on painted parts. Where possible, avoid placing on rotationally -molded plastic parts, TenderTuff-coated parts or where children may step and wear off sticker. This applies to both Freestanding Play items and Composite Playstructures. Apply sticker adjacent to or visible from the primary entrance to the structure. Apply 4'-5' above the surface. Apply at least (1) one to every structure and (2) two to large Composite Playstructures. Part No. 156847-00-000 Part No. 156845-00-000 PB/PS/FP/Evos®/Weevos® Warnina Labels 02014 by Lantlscape Structures. All rights reserved Fm 401 M8]Drrumanl#]0151300 rtplaes N 1 83066(1 Added (3) warning l.bels. Document jl/�/ t landscape structures Typical Mainstructure Post Play It Safe Label (3) Warning Labels Finished Grade Play It Safe N 18263600 PB/PS/FP/Evos1[WeevosO Warning Labels 0 2014 dy Landw St,,Mr.s All nghT, reserved fe Label J & landscape structuresro Iris ala, d. ,a,, his, cern dc,iamd 17, hind - 2 to 3 years old and noun.. uwu eo hawaha aan envth and coominadaa Adam woa-i rwun.a 21/l 64 Part No. 156844-00-000 SAFETY NOTE Chohas a a protective sWide o material roar has a Critical ignes Value or le leas) me 15014001IM he9Md'Nexj'a�nlxA# X (Rea STM ied F14e]) AWARNING Surfacing and playsurfaces _ may become HOT and cause bums. Check for hot N surfaces prior to playing an the playground. 2 1,' Part No. 182213-00-000 gl, Play It Safel AWARNIN Installation over a hard surtdctl as concreted asphalt, ""�'� or packed earth may tV result in serious hjury ^ or death Iro1117alls, a1'w 2 IK�' �-�{ 1 Fri r :a y^9 Part No. 1150.6A 'WAI in rnsoarsuu .a'..0 n.., ma aWmv,Nre h.e "ure and other playground nr caandesNrNb ehi. c ne, own da,l9naa i e .,,,, Nrmadm, equipment causing V 2�nouie,ine.d r o. 6 t 23 months old strangulation REMOVE to new wa.—,omn�aw.d a , id ane requires users helmets drawstrings. M rwem.acoordan.,an Qn8 toU vee,: nan.n to low wmciwt scarves and other .m m. n...mn axxmme. wnv. u .sm«seoin I,,— d search anducoommwnon. accessories the --.ad. crahew.aAeunw. eneck prior to playing on s"�^m.., nobv'nednaa,a.« m,na,m..anow.a,a w�wrdred. o .wn ww.u.mn the Playground. r 2112" 11a 2 1/2" If 64 Part No. 156846-00-000 Part No. 156848-00.000 Part No. 166751-00-000 Part No. 182212-00-000 Part No. 183064-00-000 2 1/i rNa plarsiwaeeargma arddaen TNSIANaauc...12 ..,,apwe,1012 aoayaee la cwd.an Trus oaysn !nn . uvvlme.a•ume N 2te ayean ehl 2to 12 yenrd old Sto 12 y¢are qla desiv,w a-,..— r ry ero r,p>a•uanb,weWFJsa arm mc..ae..unle, .Ilhlan w,e requres unesmlvwa wnmrn z mlavears airs no www«monis¢. A,v�ydmeb„ an -vin a�a,nrsmnooman woMm wa waanvwn m rew•e, user, rens aoulmaire. neon wwrvww naul,.e. aam,�wnu,ed for pmi,nooaaal need noun s,aoer n mnaw woken, arwnw re, rnile,e, onoH,r coned emam.,a co euaatwn. a m s vee., old ea.— our aial1as al MM ap awe's sYYWI,.[ea.e.nY! sum,ient n„e,-now ,nerpT ii W -.—a— Man wy�ltler, Mei.L Part No. 156850-00-000 Part No. 166815-00-000 Thai payslruchae uas naso dergne l For m arw 5 to 12 years old .,rd i ewiw, user, to haw wrriced lady hand cdorm,ii adult wpervalw TN, daYu�udure Ms childrenad 2 to a yearss old and resume, users to Mve tulliciont nrwvm and cwrdmauon. Adan wp•r d o. required. asci , Part No. 200331-00-000 Part No. 200332-00-000 Part No. 200333-00.000 Part No. 156847-00-000 Part No. 156845-00-000 PB/PS/FP/Evos0Meevos® NOTE: The Playstructure design will determine which P/ayl[Safe stickerwill be supplied. INSTRUCTIONS: Surface must be clean and dry prior to applying sticker. Peel back- ing sheet away from back of sticker and place sticker in position. Using backing sheet, rub over face of sticker to burnish down into place. Choose a location visible to adults in a conspicuous location on product. Stickers work best on painted parts. Where possible, avoid placing on rotationally -molded plastic parts, TenderTuff-coated parts or where children may step and wear off sticker. This applies to both Freestanding Play items and Composite Playstructures. Apply sticker adjacent to or visible from the primary entrance to the structure. Apply 4'-5' above the surface. Apply at least (1) one to every structure and (2) two to large Composite Playstructures. Warninq Labels 02014 by Lardsfdpe Structures All dgets reseN¢d. kmWI 82 wmunent#2RlslJpg,cplacas#laJu6(app. Aruea (3) earning land.. Document#20151300 IS& landscape structures• )els Play It Safe PB/PS/FP/EvosOMeevos® Warninq Labels ® 2014 by Landswp SUuavres An ngms rewen W. -KS •f F m 0 .fe Latey j & landscape structuress (4) y/8 Nuts w gr�SAFETY NOTE Choose a pvteclive suHatirg malarial mat has a Critical Height Value of at least the height of the Highest Accessible PaN all �SO 14 01 Height 0 Me aQaoert equipment.(RO..ASTM 1 I .a7) ce�tinea 19953600 PLAN VIEW/ FOOTING LAYOUT PlavBoostee 114665 Arch Bridge, 42" 02014 by Lahlsc pe Sitth res. NI rghts reserved Document Pin I kk landscape structures* Parts List PlayBooster{ 114665 Arch Bridge, Ort Part# Description Qty - 105327 -01 5" Half Clamp, Specify Color .................................. 4 113453-00 Arch Bridge Panel, Specify Color ............................ 2 113729-00 Offset Hanger Clamp, Specify Color ....................... 4 134946-00 Arch Bridge, Specify Color ...................................... 1 133508-00 Arch Bridge Hardware Package ........................... I 100173-00 Y." x 2" BHCS. SST .................................................. 4 100196-00 3/v" x'/v" BHCS w/Pin, SST ..................................... 4 100198-00 3/8" x 1 3/v" BHCS w/Pin, SST ................................. 16 100349-00 3/"" Low Crown Cap Nut, SST .................................. 8 100351-00 3/"" Tee Nut, SST ........................................................ 8 100353-00 '/v" Flange Nut w/Pin, SST ....................._................ 8 100362-00 '/"" Flat Washer, SST ................................................ 16 100365-00 3/3" SAE Flat Washer, SST ........................................ 4 100610-00 '/,"x'/v"Drive Rivet, AL/SST.................................4 Specifications .Arch Bridge: Fabricated from 12 GA (.105") sheet steel conform- ing to ASTM AI011. Standing surface is perforated with diameter holes. Finish: Tende Tuff , color specified. Panel: Solid color Permalenespanel. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SSI) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. l man how Weight: 160 lbs. Installation Instructions 1) With posts & decks in position, attach arch bridge to face of decks using'/"" x 1 1/v" BHCS w/pin with'/s" flat washers and %" low crown cap nuts with'/"" flat washers. See Detail. 2) Attach panels to the arch bridge using'/"" x'/j' BHCS w/pin with'/"" SAE flat washers and '/," BHCS w/pin. See Detail. 3) Attach offset hanger clamps to panel using '/&" x 2" BHCS and 3/1" flange nuts w/pin. Fasten offset hanger clamps to posts using 5" half clamps and'/"" x 1 Ys" BHCS w/pin and'/"" tee nuts. See Detail. 4) Install'/4"x%" drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 5) Install protective surfacing before users are allowed to play on the structure. t:w 0100032 Ib .tk19 MOO to %13534000. Pic Mty updated) k tided bw cmwv pp nun W Pub Lia N O_ �f Crr - e --4 e ::4 �m A rn D z o `z� o r t:w 0100032 Ib .tk19 MOO to %13534000. Pic Mty updated) k tided bw cmwv pp nun W Pub Lia IS01' f landscape DETAIL structureso SWIGGLEKNOTS BRIDGE - GROUND LEVEL DETAIL POD CABLE ATTACHMENT (7) .439" 1. D. x 1.156" Bushings Beam ,(7)Tabs L (14) Connecting it (7)'/,e' x 2" BHCS w/Pin Plugs Limited (7) Pod Cable Thread Assemblies (8) a/a t x r/,"� BHCS w/Pin 10 CableCable Cable A B C JA ble_ o (24) Cable Ball G7 Protective - ` Surfacing ` � 21 "/„” 18/'a Chain Chain 31131 16,ems Chain Chain / 24 s/,s' Chain 2113/,," 241/j," DETAIL Chain Chain DETAIL CHAINATTACHMENT CABLE BALL KNOT ( x'/e' BRCS HCS w/Pin i`t) Cables ATTACHMENT Limited �f-{4_ \ r (24) Ball (4) 1/e' x 1 'r,, BHCS w/Pin ' (4) Chains Limited Thread PlaxBooster® 193171 ® 2015 by LaMseape SWdures. All rights reserved SAFETY NOTE Choose a piotecUve au on material that hes a Cmiwl Height Value of at least the height IN the Highest Accessible ParUFall Hmghtarthe.dacentequipment. (Ref ASTM F14B).) 19497000 DETAIL BEAM ATTACHMENT (4) 5" Half C91 N O Post I(4)1/,' x 1/, Drive Rivets (8) a/a, Tee Nuts m U c7 crt r (24) a/," x 1 1/2" BHCS w/Pin with'/a' SAE Flat Washers 123" Sheet 1 of 4 9/& landscape structures° 16" Max 1111' IS0 DETAIL SWIGGLEKNOTS BRIDGE - GROUND TO DECK DETAIL GRAB BAR ATTACHMENT SAFETY NOTE Choose a protemve suffatlig material Viet has a Cntical Height Value of at least the height &the Highest Accessible Partffall Heightoftheadamttequipm (Ref.ASTM F1IBZ) 1sas7oc X a/e w/Pin N 0 +a 193171 SwiaaleKnote Bridae. 1230• ® 2015 by LarWscape Svuatum All nghts mserveE. O �17- landscape OT structures - , II (2) Grab Bars c I , 16" Deck C Max. I , Protective Surfacing SAFETY NE Choose a protective s NOT maIsuft terial mat nag a Critical Heigh Value of at leas) in t IS014001 ' HegMoofftM1exQeBentseq �no�RHalM t/ISI F1487) 194970d DETAIL SWIGGLEKNOTS BRIDGE - DECK TO DECK (4)'/s" Tee (2) 5" Half - Clamps DETAIL GRAB BARATTACHMENT ' D , e in we Rivets x 7/e, w/Pin �Tt Top Of Clamp E E iplayBochsterl 193171 • • • i • • 601 TTH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-5744678 LSI Install Help 888-4383574 LSI Direct 76: Sheet 2 of 4 (� � SAFETY NOTE J Goose a pool a urfaorq nM has a Cntical Height Value of c height of the Highest Amessito'JO® aterl�i'iea Ff4BldMexjamntaguiMara. landscape structures 194970e PLAN VIEW/FOOTING LAYOUT 1 ,,1a. 31 Booster 193171 © 2015 by Landscape Structures All nghts reserved IeKnots'M Bridae, 123" N O C:) �S2 CJ" 0 Dom{ -'-� ' �a r m a m S D o j V 1 landscape structures• (3) t a/ Long (3) %" x t/e BHCS w/Pil Limited Thr (6) 4/s" O.D Long Bush (3) % BHC: Limitea I nreaa SAFETY NOTE Cnoose a protective surfacing mshi that hes a Critical Height Value of at least the height of the Highest Accessible ParVFell IS014001 1 o he aQa a tegWp reM (Re1.ASTM NIB].) certified DETAIL 194970b PODATTACHMENT DETAIL (7) Chains n -�-i Subgrade '' a � t Concrete u. a4 .1 -y I I- I -t - (7)Bolt Links - (7) Footers Q (7) "/e" O.D. x'/2" NOTE: The hole depth for the footer needs to be deep enough, so the footer plate doesn't contact the bottom of the hole. The weight of the concrete will force the footer plate down, tightening the cable. IlayBooster° 193171 0 2015 by Landscape Stmaums. •All rights reserved X 1 f/•" able Assemblies )ds Pod Bok Plates $/a" X ]/e" BHCS w/Pin 3/1 SAE Flat Washers I DETAIL FOOTER ATTACHMENT (7) Chains,lt Loose Fill Protective Surfacing - • • • i74-0678 LSI Install Help 888-438-6574 LSI Direct 763-972-5200 Int. FAX (763( 972-3185 Ia 1•• :11 n -�-i Subgrade '' a � t Concrete (7) Footers '• Q a o Crushed Rock 12" 300 - • • • i74-0678 LSI Install Help 888-438-6574 LSI Direct 763-972-5200 Int. FAX (763( 972-3185 Ia 1•• :11 ,drim landscape Structures` DETAIL DIRECT BURY WITH POUR -IN-PLACE SURFACING Pour -In -Place Chain 1"3" Diameter oC'5 Surfacing 25-76 Concrete Slab.. — nrm C:) q 3 v Pea Gravel, Sand Or Sub O q Grade a„- -'�;c'--:• —111= : �I 8"-10" Diameter W:. Concrete Form Tube (Not Supplied) - Subgrade f Footer °b DO a Concrete Pour-In- Surfacin DETAIL DIRECT BURY WITH POUR -IN-PLACE SURFACING ( PEA GRAVEL) In z„ l • : a a I - : • • 111 • 0, • • 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328.8605 888-574.4678 LSI Install Help 888-438-6574 LSI Direct 7 SAFETY NOTE Choate a pdaceva surtaun malenal that has a Cntiwl Height Value of at least the height of the Highest Accessible Fell HeightdlheaQacenta{uilbi (Rel ASTM F1467) 179891b N O oC'5 �- -r — nrm C:) q 3 v O q CD W A& structures' Parts List PlayBooster�l193171 SwiggleKnotsru Bridge, 123" Part# Description QtY" 1"518 Grab Bar Hardware Package.....................................1 Ground Level 1001% 3/." x'/s" BHCS w/Pin, SST...........................................2 100610 '/," x '/." Drive Rivet, AUSST...................................... 4 100351 %" Tee Nut, SST ............................................................. 2 105327 5" Half Clamp, Specify Color ....................................... 4 100610 '/," x'/," Drive Rivet, AUSST ...................................... 1 154460 Pod, Specify Color..........................................................3 164367 Footer, Specify Color ...................................................... 7 Deck To Deck 176895 /a" x 1" x 2 '/;" Link, SST ............................................. 4 100610 '/," x %" Drive Rivet, AL/SST......................................4 177932 Pod Bolt Plate, Specify Color ........................................ 3 105327 5" Half Clamp, Specify Color.......................................6 178586 1 '/„” O.D. x 1 '/s" Long AL. Spacer ........................... 3 154460 Pod, Specify Color .......................................................... 3 192629 Beam, Specify Color.......................................................1 1643670 Footer, Specify Color ...................................................... 7 192734 SwiggleKnots Cable A, Black ....................................... 2 176895 '/," x 1" x 2 '/_" Link, SST ............................................. 4 192735 SwiggleKnots Cable B, Black ....................................... 1 177932 Pod Bolt Plate, Specify Cor ........er ...........................3 192736 SwiggleKnots Cable C, Black ....................................... 2 178586 1 O.D. 1 /a" Long AL. Spacer ...........................3 192737 SwigglcKnots Cable D, Black ....................................... 2 192629 Beaamm , Specify Color........... ....................................... 1 192748 Cable Bail Knot, Specify Color .................................... 24 192734 SwiggleKnots Cable A, Black.......................................2 193111 1/4" P70 x 24'/,6" Long Chain.......................................2 192735 SwiggleKnots Cable B, Black.......................................1 193112 1/4' P70 x 18 1/,6" Long Chain.......................................2 192736 SwiggleKnots Cable C, Black.......................................2 193113 1/4" P70 x 21 "/16" Long Chain... ................................... 2 192737 SwiggleKnots Cable D, Black.......................................2 193114 '/," P70 x 31 13/,6" Long Chain ...................................... 1 192748 Cable Ball Knot, Specify Color.................................... 24 195411 SwiggleKnots Bridge Hardware Package ................ I 193111 '/," P70 x 24'/,6" Long Chain.......................................2 100171 3/." x 1 IA" BHCS w/Pin, SST ...................................... 24 193112 '/4" P70 x I8'/„” Long Chain ....................................... 2 100196 3/." x'/.* BHCS w/Pin, SST 17 193113 '/," P70 x 21 "/16" Long Chain ...................................... 2 100290 ......................................... '/," x 7/i BHCS w/Pin Limited Thread, SST 7 193114 '/," P70 x 31 "/„” Long Chain ...................................... 1 100292 .............. '/.*x 1'/," BHCS w/Pin Limited Thread, SST........... 14 141541 Grab Bar, Specify Color.................................................2 100351 ............ .............. ............................. 3/," Tee Nut, SST ............................................................. .. . . , 8 195411 SwiggleKnots Bridge Hardware Package................ 1 100365 '/." SAE Flat Washer, SST............................................33 100171 '/." x 1 '/," BRCS w/Pin, SST ...................................... 24 127179 '/," O.D. x 3/," Bushing, SST ......................................... 6 100196 3/," x 7/," BHCS w/Pin, SST ......................................... 17 138915 Bolt Link, SST............................................................... 14 100290 3/,* x 7/," BHCS w/Pin Limited Thread, SST ..............7 156962 %/ O.D. x 1/2" Bushing, SST ......................................... 7 100292 3/." x 1'/4" BHCS w/Pin Limited Thread, SST........... 14 157224 .439" I.D. x 1.156" Bushing, SST ................................ 7 100351 3/." Tee Nut, SST............................................................. 8 157704 7/„” x 2" BHCS w/Pin Limited Thread, SST... ............ 7 100365 3/," SAE Flat Washer, SST ............................................ 33 162729 Connecting Plug............................................................. 14 127179 '/," O.D. x 7/s" Bushing. SST ......................................... 6 138915 Bolt Link. SST................................................................ 14 Ground To Deck 156962 '/." O.D. x '/," Bushing, SST.........................................7 100610 '/," x'/," Drive Rivet, AUSST...................................... 4 157224 .439" I.D. x 1.156" Bushing, SST................................7 105327 S' Half Clamp, Specify Color ....................................... 5 157704 7/„” x 2" BHCS w/Pin Limited Thread, SST ............... 7 154460 Pod, Specify Color.......................................................... 3 162729 Connecting Plug ............................................................. 14 164367 Footer, Specify Color......................................................7 106518 Grab Bar Hardware Package ..................................... 2 176895 3/." x 1" x 2 VI" Link. SST ............................................. 4 100196 3/i' x 7/s" BHCS w/Pin, SST... ........................................ 4 177932 Pod Bolt Plate, Specify Color........................................3 100351 '/." Tee Nut. SST.............................................................4 178586 1 '/„” O.D. x 1 '/s" Long AL. Spacer ........................... 3 100610 /." x'/." Drive Rival, ALISST ...................................... 2 192629 Beam, Specify Color ....................................................... 1 192734 SwiggleKnots Cable A, Black.......................................2 192735 SwiggleKnots Cable B, Black ....................................... 1 192736 SwiggleKnots Cable C, Black.......................................2 192737 SwiggleKnots Cable D, Black ....................................... 2 0 192748 Cable Ball Knot, Specify Color .................................... 24 cn 193111 '/," P70 x 24'/„” Long Chain ....................................... 2 S2 p —71 193112 1/4" P70 18'/„” Long Chain ....................................... 2 4� �--1 193113 1/4" P70 x 21 "66" Long Chain ...................................... 2 —� n"< 1 193114 '/. P70 x 31 "/16" Long Chain ...................................... 1 M �' 141541 Grab Bar, Specify Color ................................................. 1 ---IC—:1 195411 SwiggleKnots Bridge Hardware Package ........... I -<( p, 100171 '/i x I '/," BHCS w/Pin, SST ...................................... 24 100196 3/." x 7/." BHCS w/Pin, SST ......................................... 17 : LO 100290 3/a" x 7/." BHCS w/Pin Limited Thread, SST .............. 7 •• 100292 '/s" x 1 '/," BHCS w/Pin Limited Thread, SST........... 14 Cil 100351 34" Tee Nut. SST............................................................. 8 100365 3/," SAE Flat Washer, SST ............................................ 33 127179 5/," O.D. x'/." Bushing, SST ......................................... 6 138915 Bolt Link, SST................................................................ 14 156962 5/," O.D. x %/ Bushing, SST...... ................................... 7 157224 .439" I.D. x 1.156" Bushing, SST................................7 157704 '/„” x 2" BHCS w/Pin Limited Thread, SST...............7 Sheet 4 of 4 162729 Connecting Plug............................................................. 14 Document #20997800 Em WIM329 Dx t 209978 mphuea 19497000. Changed cable dmmptim bA. B. C a D. U ll landscape structures, Play,Boosteh 193171 SwiggleKnotsT' Bridge, 123" Specifications Cable Assembly: (Cable) Made of tightly woven polyester -wrapped, six - stranded galvanized -steel cable with a polypropylene core. (Cable Connectors) 6063-T6 aluminum Pod: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Chain: Steel '/j' (6,35 mm) straight link chain, 3,150 lbs. (1428.82 kilograms) working load limit. Finish: ProGuard. Ball Knot: Rotationally molded from U.Y. stabilized linear low density polyethylene, color specified. Pod Bolt Plate: Weldment consists of (4,75 mm) HRPO steel plate and '/&" (9,53 mm) thick HRPO steel plate. Finish: PmShields, color specified. Grab Bar: Weldment comprised of formed V," O.D. 1 t GA (.120") and'/," x 1 '/," stainless steel half clamp. Fin- ish: TenderTuf ", color specified. Beam: Weldment comprised of2.375"(60,33 mm) O.D. RS20 (.095"-.105") (2,41 mm -2,67 mm) wall galvanized steel tubing.'/," (9,53 mm) thick stainless steel plate, and'/," (6,35 mm) HRPO flat steel. Finish: ProShield, color specified. Footer: Weldment comprised of 1.660"(42,16 mm) O.D. RS20 (.120" - .130") (3,05 mm -3,30 mm) wall galvanized steel tubing and'/„" (4,75 men) HRPO sheet steel. ProShield, color specified Half Clamps: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 5 man hours Concrete Req.: Approx. 9.17 cu. ft. Weight: 141 lbs. Ground Level 146 lbs. Ground To Deck 151 lbs. Deck To Deck Fall Height: 49"-51"(1,24 m-1,29 m) Installation Instructions I) (Direct Bury) Refer to the Site Plan for footing locations. 2) Attach beam to posts at height shown. Refer to the Beam Attachment Detail. 3) (Ground To Deck & Deck To Deck) Attach grab bars to posts at dimension shown, using 5" half clamps and'/," x'/," BHCS w/pin with'/," tee nuts. Refer to the Typical Offset Hanger Clamp Assem- bly Sheet. 4) Attach cable ball knots to cables A, C and D. Refer to the Cable Ball Knot Attachment Detail. 5) Attach pod cable assemblies to pod climb across tabs. Refer to the Pod Cable Attachment Detail. NOTE: Pod cable assemblies are num- bered A. A C and D. and must be attached to pod climb across as shown. 6) Attach chains to cables C and D. Refer to the Chain Attachment Detail. 7) Feed cables A and B through 1 '/„" O.D. x 1 '/r" long spacers and holes in pods. Attach pod bolt plates to cables Refer to the Pod At- tachment Detail. 8) Attach pod bolt plates to pods. Refer to the Pod Attachment Detail. 9) Attach chains to pod bolt plates. Refer to the Pod Attachment Detail. NOTE: Chains are different lengths, and must be attached to pod bolt plates as shown. 10) Attach footers to chains. Refer to the Footer Attachment Detail. 11) With pod cable assemblies positioned properly, pour concrete foot- ings. Allow concrete footings to cure for a minimum of 72 hours before users are allowed to play on the structure. (Direct Bury With Pour -In Place Surfacing) Cut 7 lengths of con- crete form lubes (not supplied) long enough to set on top of concrete footings and be level with top of concrete slab. Concrete form tubes should be 8"-10" in diameter. Disconnect bolt links from pod bolt plates. Place concrete form tubes over chains and footers. Connect bolt links to pod bolt plates. Fill concrete form tubes with pea gravel, sand or sub grade. Pour concrete slab. After concrete slab has cared, pour surfacing. NOTE: When pouring surfacing leave a 1 "-3" di- ameter opening around chains. Refer to the Direct Burr Pour -/n - Place Surfacing Detail. 12) Install'/," x'/r" drive rivets in 5" half clamps. Drill through hole in 5" half clamps and into 5" post with a '/," or "F" (only) drill bit, insert drive rivet in hole through clamp and into post. Hammer drive rivet pin in until flush with head. Refer to the TypiciL91fset Hanger Clamp Spec Sheet. o U 13) Install protective surfacing before users aWaHpwed o play mpe structure. Cn r = <r rn a n� x D xo 0 W 9& landscape structures° I 1 1 1 CERTIFIED SAFETY NOTE hp a protective surtednq melena) mel hes a Critical Height Value M al least the height Mme Highest Accessible Pa1Fell Hei the agacenlequlpment.(Ref ASTM FUs7.) DETAIL (4)1/2' Standard SURFACE MOUNT Hex Nuts w/ 1/2" Flat Washers, -rir Support Expansion � Ij Anchors NOTE: Sufficient protective surfac- ing must cover hardware to sat- isfy fall height re- quirements. Play Safe Labor (3) %" x 7/e BHCS w/Pir w/ a/a" Flat Washers rrolealve Surfacing DETAIL DISC ATTACHMENT 120710 8" Height (Shown) Support 158997 10" Height 120711 16" Height 158998 20" Height 120712 24" Height 120713 30" Height Loose FIII 18381300 Concrete Crushed DETAIL Rock DIRECT BURY - Support I. .1i vc Surfacing E o E Goo Subgra a 'c o � N Label N Concrete Crushed Rock 12" 3 PLAN VIEW/FOOTING LAYOUT (Layout Varies -See Your Plan) 30 c 1' 4 0 — 1 I —1 a,. C, r X.- M 3 14"- � �J t.....1 360 cn Climbers• •Climbers 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888438-6574 LSI Direct 763-972-5200 Int. FAX (763( 972-3185 0 2012 by Laindsbape structures All rights resswW Document #18381300 UUk landscape structures, J \SPEC SU 83\18381300 P65 Parts List Part# Description Qty - 126956 -00 Disc, Specify Color .................................................... Approx. 1.31 cu. ft. each 169340-00 Support 8" (SM), Specify Color ............. .................. 169339-00 Support 8" (DB), Specify Color ............................... e 169342-00 Support 10" (SM), Specify Color ............................ 169341-00 Support 10" (DB), Specify Color ............................. 30" - 16 lbs. 169344-00 Support 16" (SM), Specify Color ............................ 169343-00 Support 16" (DB), Specify Color ............................. 156625-00 Support 20" (SM), Specify Color ............................ 156627-00 Support 20" (DB), Specify Color ............................. 120605-00 Support 24" (SM), Specify Color ............................ 120601-00 Support 24" (DB), Specify Color ............................. 153987-00 Support 30" (SM), Specify Color ............................ 153988-00 Support 30" (DB), Specify Color ............................. 183871-00 Disc Climber Hardware Package ......................... 1 100196-00 '/," x 7/e' BHCS w/Pin, SST ..................................... 3 100365-00 31s" Flat Washer, SST ................................................. 3 156847-00 Play Safe Label, 5-12 Yrs ......................................... 1 183064-00 Warning Label............................................................ 1 121348-00 4 Hole (SM) Hardware Package 100266-00 1/2" x 2'/," Expansion Anchor...... 100322-00 '/r" Standard Hex Nut, SST .......... 100363-00 1/2" Flat Washer, SST ..................... DB - Direct Bury SM - Surface Mount • - Quantity Determined By Your Order Specifications Disc: Rotationally molded from U V. stabilized linear lo%c density polyethylene, disc measures 14" in diameter x 7" high, color specified Support: Weldment comprised of 1.900" O.D. RS20 (.090" - .100" Wall), 1.315" O.D. RS20 (.080" - 090" Wall) and'/7a" x 5" diameter plate. Finish: ProShield', color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, staialess steel (SST)perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: SM - Approx. Y, man hour each DB - Approx. '/, man hour each Concrete Req.: Approx. 1.31 cu. ft. each Weight: 8" - 12 lbs. 10" - 1316s. Q% 16" - 1416s. �rn 20" - 15 His. 24" - 1516s. 3 30" - 16 lbs. Climbers Pod Climbers Installation Instructions 1) (Direct Bury) Dig footing as shown. See your Plan View/Footing Layout. 2) Attach disc to support using '/&" x'/a' BHCS w/pin with 3/&" flat washers, as shown. 3) (Direct Bury) Position support in footing hole and pour concrete footing. With support post plumb, prop support to hold in position. (Surface Mount) Mark anchor bolt locations on concrete slab through holes in support plate. Remove disc climber. Drill 3" deep holes on marks into concrete slab using hammer drill and 1/r" masonry bit. Tap expansion anchors into holes and secure disc climber using 1/2" standard hex nuts with 1/1" flat washers. 4) Apply labels as shown. 5) Install protective surfacing before users are allowed to play on the structure. Eco#54517 Doormen[418381300rep1aces#16934500.Addedwarning1abe1 w h tNw package. N 0 O {n rs F l7� Q% 1 �rn O� 3 O T� o W Eco#54517 Doormen[418381300rep1aces#16934500.Addedwarning1abe1 w h tNw package. 9/& landscape structuress 2"x4"x48 V," Board (Cedar) 2" x 4" x 48'/2" Board (Cedar) (2) 2" x 3" Deck Face Boards (Cedar) Play Naturalir P 2015 by Landscape Structures. All ngn s reserved 1 1 1 CERTIFIED 2" x 6" x 49" Board 2" x 4" x 47 1/2" Board (Cedar) 207582 The ndTM Rock SAFETY NOTE Choose a protective surfaong material that has a Critical Height Value of at least the height of the 1lighest Accessible ParVFall Meighl W the agacent equipment (Ref ASTM Ff08).) 2' x 4" x 49" Board (Cedar) 2" x 6" x 51" Board (Mink) 2" x 4" x 50'/," Board (Cedar) — 2" x 4" x 50'/," Board (Cedar) 9/& landscape structuress SAFETY NOTE Choose a "active sur aceg material that has a Critical Height Value of r least Ne 15014001 Here �mheesaHlagceHrae9ui t(Rea S M 1 I I F1a9L) Certified RECOMMENDED INSTALLATION TOOLS (NOT INCLUDED) PADDING FOR PROTECTION. ONLY NEEDED IF USING LIFTING STRAPS PRY BAR WITH WHEELS FOR FINAL ROCK PLACEMENT co:: cueq � a •... CALES ('. Ur,ino51TE SHH,'S COMPOSITE SHIMS FOR FINAL ROCK PLACEMENT •layBooster' 207582 The Bend Rock 601 7TH STREET SOUTH, DELANO, MINNESOTA 553284605 8885741678 LSI Install Help 388138-6574 LSI Direct 763-972-52001nL FAX (763) 9723184 ..s 0 r � - y 2 - 3" x 20' STRAPS=FOR o INSTALLING IN TIGHT AREAS •layBooster' 207582 The Bend Rock 601 7TH STREET SOUTH, DELANO, MINNESOTA 553284605 8885741678 LSI Install Help 388138-6574 LSI Direct 763-972-52001nL FAX (763) 9723184 j & landscape NOTE Choose a protective Su NOT ma10111111111 lenal mal has a Cntioal Height Value ofheial least the WFall IS014001 , Height ht f ht oflheaclacentthe seulp qment(Refie a STM CIIIUh F14811 LINING UP THE ROCK WITH POSTS INSTALL THE ROCKS WITH A TELEHANDLER. IN THE BASE OF EACH ROCK, THERE ARE ALIGNMENT CUTOUTS FOR EASE OF PLACING THE ROCKS. THE CUT OUTS ARE DESIGNED TO HELP LINE UP THE ROCKS WITH THE POSTS. USE THE CUT OUTS AS GUIDANCE FOR PROPER ROCK PLACEMENT. STRAP LOCATIONS FOR LIFTING THE BEND ROCK ALWAYS ALWAYS USE FORK POCKETS FOR INSTALL. STRAPS SHOULD ONLY BE USED IF ROCKS ARE UNABLE TO BE PLACED USING THE FORK POCKETS. ALWAYS USE PADDING BETWEEN THE STRAPS AND ROCK FOR PROTECTION PlayBoostet4 207582 The Bend Tr� Rock __ Sheet 2 of 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328.8605 888.5744578 LSI Install Help 803438.5574 LSI Direct 763-972-5200 Int. FAX Document 4207883(o N G O Va 0 �C dl -<r M x_- M f D cn .r - ALWAYS ALWAYS USE FORK POCKETS FOR INSTALL. STRAPS SHOULD ONLY BE USED IF ROCKS ARE UNABLE TO BE PLACED USING THE FORK POCKETS. ALWAYS USE PADDING BETWEEN THE STRAPS AND ROCK FOR PROTECTION PlayBoostet4 207582 The Bend Tr� Rock __ Sheet 2 of 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328.8605 888.5744578 LSI Install Help 803438.5574 LSI Direct 763-972-5200 Int. FAX Document 4207883(o SAFETY NOTE J Choose a protective surfacing mD ����//��/�/� hes a Critical HBlght Value of ISO 14001 hHai olthe aGamnleight of the secuipmdR landscape ® Certified F148)) structures` POSITIONING INSPECTION PERFORM THE INSPECTION TYPE IN THE AREAS IDENTIFIED BELOW. SEE POSITIONING INSPECTION DESCRIPTION FOR DETAILS C rs OWARNING [Failure to position rock panel correctly ay result in serious injury. USING THE PRY BAR FOR FINAL ROCK PLACEMENT Fl - ® 2015 by Landscape Structures. All rights reserved ter —16awha.6i Correct NOTE: When using pry bar, always use the steel baseplate as a contact point. Using the concrete only could damage the product. Incorrect 207582 The BendTy'Rock CD c-� u' o --n "-< Ir C", —1A �r m a m z x = 44 0 D p to SAFETY NOTE Choose a protective suKaang material that has a Critical Height Value of at least the IS014001 il T egrit otihe adl wnteq pmentbl(Re ASTM landscape`ertifi`d rrae� structures POSITIONING INSPECTION DESCRIPTION PRIOR TO SURFACING BEING INSTALLED, INSPECT OPENINGS TO VERIFY ROCKS ARE POSITIONED CORRECTLY I& e� INSPECTION A Place torso template between post and rock. Template should be perpendicular to the opening. Torso template shall not pass between post and rock. INSPECTION C Place head template between deck and rock. Template should be perpendicularto the opening. Head template shall pass between deck and rock. Booster V 2015 by Lendswpe Structures. All nights reserved. 1, INSPECTION B Place torso template between barrier boards and rock. Template should be perpendicularto the opening. Torso template shall not pass between boards and rock. 207582 The BendTy"Rock Sheet 3 of 5 landscape structures! C ERTIFIED. DETAIL CONCRETE SLAB DIMENSIONS 55'/;' Concrete Slab (3) Po Holes 791/," DETAIL CONCRETE SLAB W/LOOSE FILL Post - Loose Fill— _ 5, Geotextile Cloth Loose— M Fill g a Crushed Rock e Subgrade-- Concrete Crushed -- Rock The Bend Rock SAFETY NOTE Choose a protective surtai material Wt has a Critical Height Value & at least Ne height of the Highest Accessible Part/ all Height ofthe adjacent egqulxnenl(Rat ASTM F148T.) 207883a NOTE: Refer to Site Plan for footing & concrete slab locations. 0 m r N 0 DETAIL �^ CONCRETE SLAB W/POUR-RPIACE Post- : T n Cn Unitary r Surfacing - Crushed - Rock Or Concrete Crushed– Rock Subgrade – Con t 460 ` i Bend TIM • 601 7TH STREET SOUTH, DELANO, MINNESOTA 55326.8605 888.574-4678 LSI Install Help 888438.65741-81 Direct 763-972-5200 111111. FAX (763) 9723185 A& landscape structures° 1 1 1 CEBTIFIEB DETAIL FACE BOARD/HANDHOLD ATTACHMENT (2) Handhold Frames I SAF ETV NOTE Choose a peWve sur(aang material Nal has a Critical Heigh Value of at least Ne height of the Highest AccessiCla P.N .Il Height of Me atljacent equipment (Ref ASTM F14B7) 207878c "v (4) 3/." x 21/,' BHCS Wein w/ a/." SAE Flat (4) a/a' Standard Washers (a) a/;' x t '/;' Lag Screws Hex Nuts w/ a/;' NOTE: Using handhold frame w/ 34" SAE Flat Washers (2) 2" x 3" SAE Flat }abs as a guide, drill'/;' holes Deck Face Washers throughface boards and decks. NOTE: Line up pilot holes in Boards back of deck face board with holes in deck. DETAIL DETAIL BOARD ATTACHMENT CLAMP ATTACHMENT (16) 3/;' x 2" Lag Screws w/'/;' SAE Washers (2) Typical Offset Hanger Clamp pmt Assemblies, �anlP / . m i4 t LBH)C 5/i' x 2 4,' 1 D r S w/Pin 1 ToP Of Deck (8) Boards - d Handhold 'r-^-- Hes (16) Rai11 �(2) Hlapd'IoId Board Lr0 Frame&,- CII .c 1 . " i ' • • _ 601 7TH STREET SOUTH. DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888-438-6574 LSI Direct 763 -972 -52001st. FAX (763) 9723165 Document 1 0 d & landscape structures 5" Hall Clamp 1 1 1 CENTIFIE9 DETAIL CLAMPATTACHMENT (LEFT & RIGHT) (2) 3/e" x 7/e, 3/e' Low Crown Cap BHCS w/Pin Nut w/ 3/," SAE Flat w/ 3/;' SAE I Wanhar Flat Washers 3/e' x 1 1/s, BHCS w/Pin wl 3/," SAE Flat Washer Wall Mount Clamp Cl Half\\/ amp \` Post Cl 1/4" , x 5/e" Drive Rivet (2) ,/a„ Tee Nuts (2)'/a" x 7/e' BHCS w/Pin w/ 3/e' SAE Flat Washers SAFETY NOTE choose a protecOve surfaarg material that has a Cntiral HeigM1t Value of at least the height of the Highest Accessible PaNFell HeghlafaieadjamMaquipment (Ref ASTM F1457.) Wall Mount Bracket (2)3/."x 7/;' BHCS w/Pin W/ 3/a" SAE Flat Washers Rock Panel Wall Mount Bracket 0 cn7 O n I 3 cv 0 W 3/s' Low Crown Cap Nut w/ 3/," SAE Flat Washer (2)'/a" x 7/s BHCS w/Pin w/ 3/s' SAE Flat Washers 041,11l PlayBooster�i Bend TIL • 601 7TH STREET SOUTH, DELANO. MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888438.6574 LSI Direct 763-972-5200 Int. FAX (763) 9723185 , Uvh landscape structures` Parts List Part# PlayBoosteil' 207582 The Bend T" Rock Description Qty. 205878 The Bend Rock, Natural Tree Color ........................ 1 105327 5" Half Clamp, Specify Color .................................. 4 113729 Offset Hanger Clamp, Specify Color ....................... 2 175267 2" x 3" Recycled Deck Face Board, Cedar ............. 2 206977 Handhold Frame, Tan ................................. 2 207549 2" x 4" x 48 '/r" Recycled Board, Cedar .................. 2 207550 T' x 6" x 49" Recycled Board, Mink ....................... 1 207553 2" x 4" x 50 '/," Recycled Board, Cedar ................. 2 209595 2" x 4" x 47 'A" Recycled Board, Cedar ................. 1 207691 2" x 6" x 51" Recycled Board, Mink ....................... 1 209598 2" x 4" x 49" Recycled Board, Cedar ...................... l 207485 Railing Board Spacer, Tan ....................................... 16 206535 Wall Mount Bracket, Specify Color ........................ 2 206536 Wall Mount Clamp, Specify Color ........................... 2 100610 '/," x'/," Drive Rivet, AL./SST................................ 4 169651 Recycled Deck/Kick Board Hardware Pkge....... 2 100365 3/1" SAE Flat Washer, SST ........................................ 8 168198 3/," x 1 '/i" BH Lag Screw, SST ............................... 8 207631 Wide Handhold Hardware Package ..................... 2 100174 3/," x 2 '/r" BRCS w/Pin, SST.. ................................ 4 100198 3/," x 1'/," BHCS w/Pin, SST .................................. 4 100203 '/," x 2'/," BHCS w/Pin, SST .................................. 2 100327 '/," Standard Hex Nut, SST ...................................... 4 100351 '/," Tee Nut, SST ........................................................ 4 100365 '/," SAE Flat Washer, SST ....................................... 24 139039 '/," x 2" BH Lag Screw, SST ................................... 16 207876 Rock Clamp (Pair) Hardware Package ............... 1 100196 5/," x 74" BHCS w/Pin, SST ..................................... 8 100351 %" Tee Nut, SST ........................................................ 4 100365 3/," SAE Flat Washer, SST ........................................ 8 100349 '/," Low Crown Cap Nut, SST .................................. 2 100610 '/i' x'/g" Drive Rivet, AL./SST................................ 2 100198 3/," it 1 '/," BHCS w/Pin, SST .................................. 2 Specifications Rock Panel: Weldment comprised of5/,"(15,87tmn)&'/,"(19,06 mm) rebar, '/j' (6,35 ram) HRPO steel sheet and 7 GA. (.179") (4,55 mm) thick HRPO steel plate. Fin- ish: ProShiel&. (Rock -fully assembled) Wet cast solid pow concrete product. Finish: Latex paint made for concrete, natural colors. Poly Board: Recycled high-density polyethylene, cedar or mink in color. Handhold Frame: Weldment comprised of 1.125" (28,58 mm) O.D. ll GA. (.120") (3,05 mm) steel tubing with 203 or 303 stainless steel inserts, with 5/e' (15,87 mm) internal threads, and'Q" (6,35 nun) HRPO steel sheet. Finish: ProShield", tan in color. Spacer Tube: Made from 1 '/a' (28,57 mm) O.D. 6061-T6 alumi- man tube. Finish: ProShield, tan in color. Wall Mount Brkt.: Fabricated from 7 GA. (.179") (4,55 mm) thick HRPO steel plate. Finish: ProShield°, color specified. Wail Mount Clamp: Weldment comprised of'Q' (6,35 mm) HRPO steel plate. Finish: ProShielda', color specified. Installation Instructions I ) (Direct Bury) Dig footing holes and build frame for concrete slab. Refer to Direct Bury Detail and Site Plan. Warning: Never crawl under any part of the Rock Panel - espe- cially when it is only supported by a forklift. 2) With posts plumb and deck level, pour concrete footings and slab. NOTE: Concrete slab must be level. 3) Allow concrete to cure a minimum of 24 hours before placing Rock Panel on concrete slab. 4) To unload a Rock Panel a "Lull" type material handler with at least an 8000 lb. capacity is recommended. NOTE: At least 2 people am mcommended for Rock Panel installation. One person to operate the material handling equipment and one person to spot far the op- erator. 5) Pick tip the Rock Panel by inserting the material handling forks into the forklift pockets. Be very careful to keep the Rock Panel level to the ground when raising or lowering. Do not tip the Rock Panel on a comer or edge. Do not contact the concrete face of the Rock Panel with material handler forks, chipping can occur. Refer to the Site Plan for proper orientation. 6) Attach Rock Panel to posts. Refer to the Wall Bracket Details. 7) Attach offset hanger clamps to posts at heights shown using 5" half clamps,'/," x 1 '/," BHCS w/pin and'/," tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 8) Attach handhold frames to offset hanger clamps, using 5/," x 2 '/," BHCS w/pin. 9) Line up pilot holes in boards with spacers and handhold frame tabs and attach, using'/g' x 2" lag screws with'/," SAE flat washers. Refer to the Board Attachment Detail. 10) Lineup pilot holes in deck face board with holes in deck and attach, using 3/s' x 1 '/r" lag screws with %" SAE flat washers. Refer to the Face Board Attachment Detail. 11) install'/f x'/," drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 12) Install protective surfacing before users are allowed to play on the structure. 13) NOTE: After Installation if Touch-up/Repairs are needed, con- tact Landscape Structures at 1-888-574-4678. Sheet 5 of 5 Document #20788300 Z5 .� CR) -T1 I� a —4 Clamp: Cast aluminurrCf�iniQv PrdShield3' Ch}6r specified. Fasteners: 01 Primary faste— Tall be sock�nd pinned 't)perASTM tampelproofin gexstaii3*sstee F 879 unless otpelwige indicated (siffl4ecific prod- uct installation/gpoWicatimiss. `--' Installation Time: Approx. 10 marl hours ctt Fall Height: 72" (1,83 m) z Concrete: Approx. 17.75 cu. ft. Weight: 4683 lbs. Installation Instructions I ) (Direct Bury) Dig footing holes and build frame for concrete slab. Refer to Direct Bury Detail and Site Plan. Warning: Never crawl under any part of the Rock Panel - espe- cially when it is only supported by a forklift. 2) With posts plumb and deck level, pour concrete footings and slab. NOTE: Concrete slab must be level. 3) Allow concrete to cure a minimum of 24 hours before placing Rock Panel on concrete slab. 4) To unload a Rock Panel a "Lull" type material handler with at least an 8000 lb. capacity is recommended. NOTE: At least 2 people am mcommended for Rock Panel installation. One person to operate the material handling equipment and one person to spot far the op- erator. 5) Pick tip the Rock Panel by inserting the material handling forks into the forklift pockets. Be very careful to keep the Rock Panel level to the ground when raising or lowering. Do not tip the Rock Panel on a comer or edge. Do not contact the concrete face of the Rock Panel with material handler forks, chipping can occur. Refer to the Site Plan for proper orientation. 6) Attach Rock Panel to posts. Refer to the Wall Bracket Details. 7) Attach offset hanger clamps to posts at heights shown using 5" half clamps,'/," x 1 '/," BHCS w/pin and'/," tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 8) Attach handhold frames to offset hanger clamps, using 5/," x 2 '/," BHCS w/pin. 9) Line up pilot holes in boards with spacers and handhold frame tabs and attach, using'/g' x 2" lag screws with'/," SAE flat washers. Refer to the Board Attachment Detail. 10) Lineup pilot holes in deck face board with holes in deck and attach, using 3/s' x 1 '/r" lag screws with %" SAE flat washers. Refer to the Face Board Attachment Detail. 11) install'/f x'/," drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 12) Install protective surfacing before users are allowed to play on the structure. 13) NOTE: After Installation if Touch-up/Repairs are needed, con- tact Landscape Structures at 1-888-574-4678. Sheet 5 of 5 Document #20788300 SAFETY NOTE Choose a pmective surfaang mater al [ha[ has a Cntioel Height Value of at least the height of the Highest Accessible PaiV all IS0 14003 r I I HeightmlheagaceNeguipn (Ref ASTM F1481) landscape °"" structures° DETAIL 19026900 PLAN VIEW PANELATTACHMENT FOOTING PLAN (2)Typical Offset 56" Deck Hanger Clamp 3 1/,"/ 63 Assemblies (2)e/e' Flange - n 21" 21" Nuts w/Pin '"1 I < t �--- Typical (2) Handhold C3 cn rn Mainstructure Panels (2) Space r v 1 • 1 Post Tubes 38,19-65Min• Panels tlHCS w/Pin panel To r DETAIL Top O1 ° peck Surface Mount (64" Deck) TOQ of ° Vertical Clamp 3/," x 11/," BHCS Ladder w/Pin w/'/;' SAE 1/2' Standard Hex Nut Flat Washer w! 1/2' Flat Washer Max 1/j' x 2 3/4" Expansion w 15" .. Anchor ---39f '/," Low Crow Angle Plate n Cap Nutw/'/e' SAE Flat her Deck NOTE: Sufficient protec- Concrete Slab tive surfacing must cover 4) a/." Flange hardware to satisfy fall of Nutsw/Pin Crushed height requirements. peck (4) a/," x r/e, Rock BHCS w/Pin w/ a/," SAE Flat Washers DETAIL (2) Standard Hex Surface Mount (72" Deck) Nut W/ a (2)+/i' Standard Hex Nut w/ Nuts w/ '/,,Flat SAE Flatt Washers Footer Washers — Expansion —416 AnchorsConcrete Slab (2)'/° x 1 Vil Crushed Rock BHCS w/Pin w/a/;'SAE DETAIL Flat Washers Direct Bury Footing Footer Loose Fill a�3<' Protective Surfacing Subgrade Vertical ,'.';•'- Ladder Concrete a '/;' Low Crown - '- Cap Nut , _;' `protective wP/e" SAE Flat !H x 1 /, Surfacing Crushed Washer BHCS w/Pin g Rock Footer w/'/i' SAE Flat Washer 12" 116249 Vertical Ladder, 64" - 72' Decks 05 Document#19026900 U i�) landscape structures' Parts List PlayBooster' 116249 Vertical Ladder, 641e - 72" Decks Part# Description Qty. 115779 Vertical Ladder, 64"/72", Specify Color ................. 1 139563 Handhold Panel, Specify Color ................................ 2 180703 Footer (DB), Specify Color ....................................... 1 180705 Footer (SM), Specify Color ...................................... 1 180702 Angle Plate (SM), Specify Color ............................. 1 105327 5" Half Clamp, Specify Color ...............................– 2 113729 Offset Hanger Clamp, Specify Color ....................... 2 113468 Spacer Tube, Specify Color ...................................... 2 190270 Vertical Ladder (Tenderdeck) Hardware Pkg ... 1 124460 34" x 3 34" BHCS w/Pin, SST .................................. 2 100196 3/," x Y," BHCS w/Pin, SST ........................... --...... 4 100198 '/," x I '/e" BHCS w/Pin, SST .................................. 7 100327 '/c" Standard Hex Nut, SST ...................................... 2 100349 s/a" Low Crown Cap Nut, SST .................................. 1 100351 '/a" Tee Nut, SST ........................................................ 4 100353 3/e' Flange Nut w/Pin, SST ....................................... 6 100365 '/e" SAE Flat Washer, SST ....................................... 10 111392 2 Hole ;SM) Hardware Package 100266 Y..: x 2 /i' Expansion Anchor...... 100322 '/, Standard Hex Nut, SST .......... 100363 1/2" Flat Washer, SST ..................... 116432 1 Hole ISM) Hardware Package ........................... 1 100266 1/2" x 2 /4' Expansion Anchor .................................. 1 100322 'A" Standard Hex Nut, SST ...................................... 1 100363 1/2" Flat Washer, SST ................................................. 1 DB - Direct Bury SM = Surface Mount Sclecifications Vertical Ladder: Weldment comprised of 1.125' O.D. 11 GA (.120"I steel tubing, 1.029" O.D. RS -20 (.070" - .080")) and 3/ , x 2" wide steel flat plates. sh: TenderTufP", cotor specified. Footer: Fabricated from 1.315" O.D. RS -20 (.050" - .09(111) galvanized steel tubing. Finish: ProShield', color specified. Handhold Panel: Solid color Permalenex, color specified Spacer Tube: Made from 6061-T6 aluminum 7/8" O.D. x 1 "/26". Finish: ProShield. color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof mdesign, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: DB - Approx. 1 '/2 man hour SM - Approx. 1 man hour Concrete Req.: 1.3 cu. ft Weight: DB 64"/72" - 51 lbs. SM. 64" - 54 lbs. Fall Height: SM 72" - 56 lbs. Da Height Installation Instructions Direct Bury 1) Dig footing to depth and spacing, as shown. 2) Attach footer to ladder, using a'/R' x I Ys" BHCS w/ in with 3/," SAE flat washer and a 3/," low crown cap nut with %" SAE flat washer, as shown. 3) Attach ladder to deck, using %" x 1 '/s" BHCS w/pin with 3/," SAE flat washers and 1/i" standard hex nuts with 3/," SAE flat washers, as shown. 4) Attach handhold panel to the face of the deck, using'/," x'/," BHCS w/Pin with'/," SAE flat washers and'/, " flange nuts w/ in, as shown. NOTE: Be sure handhold panels are snug to vertical ladder. 5) Attach offset hanger clamps to posts at height shown, using 5" half clamps and I/," x 1 '/," BHs CS w/pin with " tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 6) Attach panels to offset hanger clamp assemblies, using'/e" x 3 3/," BHCS w/pm, spacer tubes and 3/," flange nuts w/pin. See Panel At- tachment Detail. 7) With ladder plumb,ppour concrete footing. Allow concrete footing to cure a minimum of 72 hours before users are allowed to play on the structure. 8) Install protective surfacing before users are allowed to play on the structure. Surface Mount I ) Attach footer to ladder, using a 3/," x 1'/," BHCS w/ in with %" SAE flat washer and a %" low crown cap nut with 3/," SAE flat washer, as shown. NOTE: The Footer (SMP is usedlor the 71 "deck height, and the Angle Plate (SAI) is used jar the 64 deck height. 2) Attach ladder to deck, using %" x I '/e' BHCS w/pin with 3/," SAE flat washers and 3/," standard hex nuts with 3/," SAE flat washers, as shown. 3) Attach handhold panel to the face of the deck, using 3/s' x 7/a' BHCS w/ pin with 3/g" SAE flat washers and 3/," flange nuts w/pm, as shown. NOTE: Be sure handhold panels are snug to vertical ladder. 4) Attach offset hanger clamps to posts at height shown, using 5" half clamps and Y." x 1 '/." BHCS w/pin with %" tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 5) Attach panel to offset hanger clamp assemblies, using 3/r" x 3 3/4" BHCS w/pin, spacer tubes and 3/," flange nuts w/pin. See Panel At- tachment Detail. 6) Using a'/2"hammer drill and /2" masonry bit, drill anchor bolt holes into concrete slab 3" deep through holes in footer plate or angle plate, as shown. 7) Tap expansion anchors into holes and fasten, using'/2" flat washers and 'A" standard hex nuts, as shown. 8) Install protective surfacing before users are allovW to play on the structure. -- CD �O ,—I n --- 4 n�C 1 p1 c �, ri a 9 r s O W Em4054756�1#I90I6900rtph 18158500. Rett vwirsl leddeelmrM package. A& landscape structures° PLAN VIEW/FOOTING LAYOUT 46 De M" -[Z- UeCKS-11'1.-11Mf (2)Handhold Panels \ Typical PlayBooster �O���e� Post � igt°'dP�y0\ n x Washers (4)'/." Flange Nuts w/Pin SAFETY NOTE CMpse a prolective sunaarg material mai tm . CM1tiwl Heipp� Value of at lease the ISO 14001 r bpMo Cepa emseQ pme (Re A TM I I F113]) ceruned 19043700 ELEVATION Key A B 48" Deck 15 3/," 35'/,' 56" Deck 233/,' 35 3/,' 64" Deck 171/,-- 34" 72" Deck 251/," 34" Acal ncrete oting DETAIL HANDHOLD PANEL set eune ATTACHMENT (2)Typical Offs Hanger Clamp (2)'/,' Flange Nuts w/Pin (2) Spacer Tubes DETAIL SURFACE MOUNT /, Ex x Expansion Anchors & 1/2" Standard Hex Nuts w/ '12" Flat Washers Concrete— Slab oncrete Slab Crushed Rock PlayBooster® 1 i 02013by LarMsd wStructures. •NInghtsreserved (2) Handhol Panels (2)'/,' Standard Hex Nuts w/3/." Flat Washers Climber (2) C3 7 r, r; 7 .(2)x3I " -� BHCS w/Pin in 12" 300 DETAIL DECK ATTACHMENT Deck Snake See Key A See Key B Rode (2),/," x 11/s BHCS w/Pin w/3/," SAE Flat Washers DETAIL SUPPORT ATTACHMENT Surfacing a NOTE: Sufficient protec- tive surfacing must cover hardware to satisfy fall Snake height requirements. Climber 913 Snake Climbers. 48e1a2e (2) Supports Document #19043700 PlayBooster® 122913 Snake Climbers, 48"-72" landscape structureir Parts List Part# Description Qty. 139561 Handhold Panel, Specify Color ................. ......_...... 2 142047 Snake Climber, 48" & 56", Specify Color .... ._...... 1 142048 Snake Climber, 64" & 72", Specify Color .............. 1 142101 Support, 48" Deck (SM), Specify Color ................. 2 142103 Support, 56" Deck (SM), Specify Color ................. 2 142084 Support, 48" & 64" Deck (DB), Specify Color...... 2 142083 Support, 56" & 72" Deck (DB), Specify Color...... 2 142105 Support, 64" Deck (SM), Specify Color ................. 2 142107 Support, 72" Deck (SM), Specify Color ................. 2 105327 5" Half Clamp, Specify Clamp ................................. 2 113729 Offset Hanger Clamp, Specify Color ....................... 2 113468 Spacer Tube, Specify Color ...................................... 2 190446 Snake Climber Hardware Pkg .............................. 1 124460 '/e" x 3'/4" BHCS w/Pin, SST .................................. 2 100196 '/e" x 7/e" BRCS w/Pin, SST ..................................... 4 100198 '/e" x I '/e" BHCS w/Pin, SST .................................. 6 100327 '/," Standard Hex Nut, SST ...................................... 2 100351 '/e" Tee Nut, SST ........................................................ 4 100353 '/e" Flange Nut w/Pin, SST ....................................... 6 100365 '/e" SAE Flat Washer, SST ........................................ 6 100362 '/e" Flat Washer, SST ................................................. 2 100611 '/," x %" Drive Rivet, AL/SST................................. 4 121348 4 Hole (SM) Hardware Package ........................... 1 100266 '/_" x 2'/," Expansion Anchor .................................. 4 100322 V.," Standard Hex Nut, SST ...................................... 4 100363 Flat Washer. SST .................................................4 DB-Dlrect Bury SM -Surface Mount Specifications Climber: Weldment comprised of 1.660" O.D. RS -40 (.111" - .121") galvanized steel tubing, and 1.315" O.D. RS - 20 (.080" - .090") galvanized steel tubing. Finish: ProShield', color specified Supports: Formed from 1.660" O.D. RS -40(.111" -.121") gal- vanized steel tubing. Finish: PmShield, color speci- fied. Handhold Panel: Solid color Pennalenee, color specified. Spacer Tube: Made from 6061-T6 aluminum'/," O.D. x 1 "/16". Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: SM - Approx. 1 '/r man hours DB - Approx. 2 '/i man hours Concrete Req.: Approx. 2.6 cu. fl. Weight: Off 48" & 56" Deck (SM) - 99 lbs. Off 48" & 56" Deck (DB) - 1071bs. Off 64" & 72" Deck (SM) - 106 lbs. Off 64" & 72" Deck (DB) - 114 lbs. Fall Ileight: Deck Height Installation Instructions I ) (Direct Bury) Dig footing holes spaced as shown. Refer to the El- evation Key. 2) Insert supports into snake climber. Attach snake climber to deck us- ing'/ x P'/e" BHCS worts with'/e" SAE Flat washers and N" stan- dard Rex nuts with'/e" Flat washers. Refer to the Deck Attachment Detail. 3) With suppports plumb drill through holes in snake climber into sup- Rorts wmh a'/4 or Tl' (only) drill bit. Insert'/ " x'/ " drive rivets m oles and hammer drive rivet pin in until Flush wilt[ head. Refer to the Support Attachment Detail. 4) Attach handholdpanels to the face of the deck using'/," x'/s' BHCS w/pin with'/," SAE flat washers and '/," Flange nuts w/pm. 5) Attach offset himgger clamps to posts at heights shown using 5" half /, clampps,'" x I '/s' BHCS w/pin and'/," tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 6) Attach handholdpanels to the offset hanger clamp assemblies using '/4" x 3 '" BHCS /4w/pin, spacer tubes and Y.." flange nuts w/pin. Refer to the Handhold Panel Attachment Detail. 7)(Direct Bury) With snake climber in final position, pour concrete Clings. Allow concrete footings to core a minimum of 72 hours before users are allowed to play on the structure. (Surface Mount) Mark anchor bolt locations on concrete slab through holes in anchor plate and remove climber. Drill '/ " x 3" deep holes on marks into concrete using hammer drill and V," masonry bit. Tap expansion anchors into drilled holes. Reposition climber and reat- tach to the face of the deck following step 3. Fasten anchor plates to expansion anchors using'/i" standard hex nuts with 'I," Flat washers. 8) Install protective surfacing before users are allowed to play on the structure. r� 0 O v=1 -4'T1 C-)-< C, rT =Cm y ! •' ac � Ox O v O W ECO047(d Uucunrom p19D1J70a rtplrcesp113N4pa. Replawdherdwme pc4egc. j & landscape structures- Typical P PlayBooster Mainstructure _ Post (6) Typical Offset Hanger Clamp Assemblies in Top "34�— Deck , (6) 3/s' x 7/a' BHCS w/Pin w/ 1/," SAE Flat Washers (6)'/l Flange/; Nuts w/Pin i i Top 01 l Clamp i m Handhold , O SAFETY NOTE dftm FChoose a protective ,urtaorp material Vial rias , CnVcal Height Value of el least the IISS01�4'0�03 hM�gMm�eaaa '.,upmari (RM ASTM i7�IWY1% Cer'i'lea I F1487) 15489700 DETAIL PANELATTACHMENT (6)'/," Flange p� Nuts w/Pin /, L (10) Hand Grips (20)'/," x 1 Y." BHCS w/Pin Spacer N \ O .Y-.. � (6)'/;' x 3'/;' BH w/Pin (6)Typical Offset 84/j/171 Hanger Clamp (I!( p Assemblies 6 i 48" - 72" 297740 Deck 8'/4%171 a o ZY Vertical Ascent Panel (20)3/," Flange isNuts w/Pin L (10) Hand Grips (20)'/," x 1 Y." BHCS w/Pin Spacer N \ O .Y-.. � (6)'/;' x 3'/;' BH w/Pin dho� 84/j/171 erlil Ascent 1 M c' � t.C3 °✓ Y Ln 4 - 6 4/4%171 Dock Height A B 48" 84/j/171 217530 56" 61/4"/171 25"/640 64" 6 4/4%171 297740 72" 8'/4%171 33"/840 OP 0CtaTnp Protective T_ Surfacing Gfa.- PlayBoosterO 145624 Vertical Ascenr, ' 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888-438-5574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 Document 1, O /1� PlayBooster° 145624 Vertical Ascent', 48"-72" landscape structures, Parts List Installation Instructions Part# Description Qty. 182957 Vertical Ascent Handhold Panel. Specify Color ......... 2 145597 Vertical Ascent Panel, 48" Deck, Specify Color ........1 _ �" 145596 Vertical Ascent Panel, 56" Deck, Specify Color ........1 145595 Vertical Ascent Panel, 64" Deck, Specify Color ........1 145585 Vertical Ascent Panel, 72" Deck, Specify Color ........1 105327 5" Half Clamp, Specify Color......................................6 113729 Offset Hanger Clamp, Specify Color ...........................6 113468 Spacer Tube, Specify Color..........................................6 100610 '/; x 14" Drive Rivet, AUSST.....................................6 145792 Hand Grip Set...............................................................1 143110 Hand Grip, Blue.............................................................2 143110 Hand Grip, Yellow.........................................................2 143110 Hand Grip, Red..............................................................3 143110 Hand Grip, Green...........................................................3 145616 Vertical Ascent Hardware Package ..........................1 100196 %" x %" BHCS w/Pin, SST.........................................6 100198 1/1" x 1 '/." BHCS w/Pin, SST ..................................... 32 100351 1/," Tee Nut, SST........................................................... 12 100353 3/." Flange Nut w/Pin, SST .......................................... 32 100365 1/." SAE Flat Washer, SST............................................6 124460 '1." x 3 1/," BHCS w/Pin, SST......................................6 Specifications Band Grip: Made from Polyester Resin. Hand Grips measure approx. 51/,' long x 2/," wide x I '/." high. Panels: Solid color Pennalene", color specified. Spscer Tube: Made from 6061-T6 aluminum 7/." O.D. Finish: ProShield", color specified. Clamps: Cast aluminum. Finish: PtoShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) MASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 2 man hours Weight: 48" Deck Height - 83 Has. 56" Deck Height - 91 lbs. 64" Deck Height - 99 lbs. 72" Deck Height - 106 lbs. Fall Height: 531/3"/1358 (48" Deck Height) 61'/i"/1562 (56- Deck Height) 69'/,"/1765 (64" Deck Height) 7711"/1968 (72" Deck Height) I ) Attach handhold panels and vertical ascent panel to deck using'/,' x 7/." BHCS w/pin with'/," SAE flat washers and'/," flange nuts w/pin, as shown. 2) Attach handhold panels and vertical ascent panel to offset hanger clamps using'/.' x 3 3/," BHCS w/pin, spacer tubes and'/"" flange nuts w/pin. Refer to the Panel Attachment Detail. 3) Attach offset hanger clamps to posts at heights shown using 5" half clamps, 1/1" x 1 '/." BHCS w/pin and'/; tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 4) Attach hand grips to handhold panels and vertical ascent panel using 3/," x 1'/," BHCS w/pin and 3/," flange nuts w/pin, as shown. 5) Install Y." x Y." drive rivets in all 5" half clamps. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 6) Install protective surfacing before users are allowed to play on the structure. Fin x5N66 DocumM la3981na rtplecc l}ttl970a. ReplecW hmdG+ld M"14. N 0 E; cn O C-) Y � C-) --e � 1 _ �" CD S 0 Y O W Fin x5N66 DocumM la3981na rtplecc l}ttl970a. ReplecW hmdG+ld M"14. V _ landscape structures° DETAIL INFILL PANEL ATTACHMENT Barrier (5)'/." Flar Nuts w/Pin Infill Panel Star Set Climber Protective Surfacing C E R T I F I E D (5) 3/:' x 7/;' BHCS w/Pin w/'/:' SAE Flat Washers DETAI (2) a/," x 21/4" BHCS w/Pin w/ a/," SAE Flat Washers Net SAFETY NOTE choose a prolective suffacm, matenal that has a Critical Haight value of at lees[ he height of the Highest Accessible PaNFell Height of the adjacent equipment. (Ref. ASTM F148n 20782100 3) 5" Half (4) Steel Posts Required (See Direct Bury Detail) Infill Panel t__ \I r Typical Offset Hanger Clamp Assembly BHCS w/Pin 72" Deck I'ras � m i i i i er 1 V;' O.D. x 1 '4" (2) %" Standard Hex Nuts w/ d/e" SAE Flat Washers 601 7TH STREET SOUTH, DELANO, MINNESOTA 565284606 888374-4678 LSI Install Help 888-438$674 LSI Direct 763. Sheet 1 of 3 Document#21308400 SAFETY NOTE choose a prolective sValue o material mat I a Cnlioal Height Value ni el 1ed91 IM1e Height of ltrh Highest paue t equipment Accessible nt (Ratl ASTM1 the aelacenl eQoipmani (Ref. ASTM F1d°]) landscape 177934a structures` PLAN VIEW/FOOTING LAYOUT Square DETAIL AUeck TTACHMENTbf,ple�e�oo 0 0 1pA c Star Seeker Climber (3) °/j x 1" x 2'/{ dy ° Q Link Plates BHCS w/ x'/° e1 ,.� 104"/2640 `t HC Pin Limited -- �- enter Of Post To Center Of Concrete Footing ll Thread n er 104 n (3) Ya" Standard 0 n 40 ' ° Hex Nuts (3) "Ife" x 2" BHCSw/Pin - -- (3)Turnbuckles Limited Thread DETAIL STEEL MAINSTRUCTURE POSTS (3)Anchor Concrete DIRECT BURY Bars Footing 42" DETAIL O O ANCHOR BAR FOOTING o o (3) Turnbuckles Hex Nuts an da d (3) 112' - L;10e�Fill o a r P1otective v i O 0 BHCS w/Pin Limited Thread Sxirfacing 0 g I_ 1680----j Mainstrudure Subgrade `^ Posts � Loose Fill -- Concrete —4 Protective Surfacing Im(3)Anchor _ Subgrade Bars II c1 Concrete zg Crushed r� a �1 Rock 36" Dia. Crushed Rock 910 Pla Bo/_ o 148039 Star Seeker Climber, 722" D}�e�ck Only = 02015 by Landscdpd Stmctmes- All rights resew I S & landscape structures SAFETY NOTE Choose a protective sudadng material that has a Critical Height Value N i leas) tha height of the Highest Accessible PaN all Height of the adjacent equipment (Ref. ASTM F148]) 148042CO DETAIL TRI -DECK FOOTING 6T ^ t t NOTE: Steel posts are required when attach- ing Star Seeker Climber ttach- ingStarSeekerClimber '^ to a Tri -Deck. NI1RIl�a� `V `• • I Steel DETAIL Tri -Deck DIRECT BURY Posts Loose Fill - c Protective—. -------- --- --------- Surfacing C3 DETAIL" `' HEXAGON DECK FBQ INCA Subgrade t ,_•tri Cn T ..{� 3 1 •, Concrete +' cn DETAIL - Steel k DIRECT BURY Hex Post \ _ Loose Fill - Hexagon Deck ; Steel Post Protective. Required Surfacing I p IIII I Subgrade x Concrete 11 ame er - 910 ---- Concrete 148039 Star Seeker Climber, 72" Deck On Sheet 2 of 3 CM15by Landscape StF�Wles J Document#21308400 k& landscape structures` DETAIL CLAMP ATTACHMENT (3) Net AMPS FOR STAR SEEKER Assemblies Tap Of Clamp I I I Steel Post— Only gg TOPOf V d Clamp I ' I I I 1 " I � I ' - Top Of Deck j r 1 I ' I 1 I ' I ' I ' 1 NOTE: Bottom net clamp assembly will set on top of deck. DETAIL CLAMPS FOR STAR SEEKER (TOP VIEW) Steel Post NOTE: Angle net clamp assemblies in line with anchor bars. I I 1 I I I I I I (6 Ni BottomNet Clamp -,Assembly CLAMPS FOR ENCLOSURE PANEL 0 M Q^j Middle Net Clamp Assembly -Top Net Clamp Assembly (6) 3/e1 x'/8" BHCS w/Pin 3/o" Tee ?op Of Deck h� I I Infill Panty 1 DETAIL STAR SEEKER TO POST ATTACHMENT 5" Half Steel Post 170994b Net rs (3)'/;' 0. D. X'/," I G? Bushings L t (3) o/e' A BHCSw/Pin Limithed ThreagKFri y - o Booster 148039 Star Seeker Climber, 72" Deck Only o P 2015 by Landscape Slmclures All nghts reserved 9/& landscape structures` SAFETY NOTE choose a protective Wei material Mat has a Cntinl Height Value of at least Ma height of the Highest Accessible PaNFall Haight of the adjacent equipment. (Ref. ASTM F1a97) 177934b PLAN VIEW OF INSTALLATION Pour In Place Surfacin Concrete T bN� all n n DETAIL PLAN FOR FOUNDATION �c m .<r rte, Radius Pour In Place Surfacing On This Edge \ Turnbuckle 'tn Ln t Pour In Place Surfacing Loose Fill Material 36" Dia 910 PlayBoostero Detail PlanFor Pour In Place Surfacir 601 7TH STREET SOUTH, DELANO, MINNESOTA 66328.8606 888-674-4678 LSI Install Help 888.4.73-6674 LSI Direct 763-972.6', Sheet 3 of 3 Document #21308400 Alk PlayBooster�' 148039 Star Seeker Climber, 72" Deck Only landscape structures' Parts List Part# Description Qty. 170930 Barrier, Specify Color..._._._ ....... .................................. 1 17'0931 Infill Panel, Specify Color.............................................1 203672 Net, Specify Color_._ .......... ....... ._.................. ......_. ..... 1 144565 Anchor Bar......._ ......................... ..._......... ...... .............. 3 105327 5" Half Clamp, Specify Color...._... .............................. 4 113729 5" Offset Hanger Clamp, Specify Color........................1 161898 Net Clamp, Specify Color ...... -- ...................................3 100610 '/: x % Drive Rivet, AIISST......................................4 151072 1 '/: O.D. x I '/; AL. Spacer, Specify Colm...............2 171654 Turnbuckle ._._......._____.......---- ..............................3 213093 Star Seeker Climber Hardware Package ................1 100196 %"x% BHCSw/Pin,SST..._.................................... II 100198 3/i x 1 '/," BHCS w/Pin, SST.......................................2 100199 3/.' x2'/: BHCS w/Pin,SST...................................... 2 100203 3/."x2'/: BHCS w/Pin, SST .......................................1 100290 3/, x'/.' BHCS w/Pm Ltd. Thread Bolt, SST._._.........6 100327 3/: Standard Hex Nut, SST...........................................2 100351 !/."Tee Nut. SST ...................................................8 100353 3/ ' Flange Nut w/Pin, SST............................................5 100365 3/: SAE Flat Washer. SST.............................................9 157704 7/, j x 2' BHCS w/Pm Ltd. Thread Bolt, SST.. _...._._..6 127179 3/: O.D. x3/," Bashing, SST ....... ....... _._...................... 3 176895 3/." x I' x 2 V2' Link Plate, SST....................................3 100328 7/1: Standard Hex Nuts, SST.........................................6 Specifications Net: Made oftightty woven potyesterw'rapped, six -strand- ed galvanized -steel cable with a polypropylene core, color specified. Connector fabricated from 1.250" O.D. 6063-T6 aluminum. Anchor Bar: Weldment comprised of/," x 3" flat steel and'/," x 8" square plate. Finish: Galvanized. Infill Panel: Solid color Permalenc`, color specified. Barrier: Weldment comprised of 1.125" O.D. I I Ga. (.120") steel tube per ASTM A513 with 203 or 303 stainless steel threaded inserts with I/." internal threads and '/," tabs. Finish: TenderTufl13M, color specified. Net Clamp: Weldment comprised of x I '/," HRPO flat steel and .375" stainless steel sheet. Finish: ProShield', color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tam- perproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific product installation/specifications). Installation Time: Approx. 2 man hours for net and enclosure panel Approx. 2 man hours for anchor bar footings Wright: 135 lbs. Concrete: Approx. 48 cu. A. (3 anchor bars) Approx. 30 cu. ft. (steel square deck mainstmcture posts) Approx. 14 cu. ft. (steel hes-deck mainstructure post) Approx. 28 cu. ft. (steel tri -deck mainstructure posts) Fall Height: 84" (2,13 m) Installation Instructions 1) Dig footings to depths and spacing, as shown. 2) Place anchor bars in footing holes to dimensions shown. Anchor bars should be angled in line with center post. 3) With anchor bars in final position, pour concrete footings. NOTE: Allow mainstructure and anchor bar concrete footings to cure for a minimum of 72 hours before attaching Star Seeker Climber and turnbuckles. 4) Attach offset hanger clamp assembly to post at height shown, using 5" half clamp,'/," x 1 '/." BHCS w/pin and'/." tee nuts. Refer to the Clamp Attachment Details. 5) Attach net clamps to posts at height shown, using 5" half clamps,'/;' x'/," BHCS w/pin and '/." tee nuts. Refer to the Star Seeker to Post Attachment Details. 6) Attach barrier to offset hanger clamp assembly using 3/,"x2'/j"BHCS w/pin. 7) Place 1 '/." O.D. x 1 3/," spacers between barrier tabs and deck. Attach barrier to deck using'/." x 2'/," BHCS w/pin with'/," SAE flat washers and 3/," standard hex nuts with'/; SAE flat washers. 8) Attach infill panel to barrier acing Y." x Y." BRCS w/pin with SAE flat washers and'/," flange nuts w/pin. Refer to the Infill Panel Attachment Detail. 9) Insert'/." O.D. x'/," bushings into net clamp tabs. Attach net to net clamps with bushings, using 3/," x 7/." BHCS w/pin limited thread. Refer to the Star Seeker to Post Attachment Detail. 10) Attach tumbuckles to net and anchor bats. Refer to the Turnbuckle Attachment Detail & Anchor Bar Footing Detail. 11) Tighten turnbuckles evenly until net is tight, but not bending post. 12) Install '/," x 3/," drive rivets in all 5" half clamps. Drill through hole in 5" half clamps and into 5" post with a '/," or "F" (only) drill bit, insert drive rivet in hole through clamp and into post. Hammer drive rivet pin in until flush with head. Refer to the Typical Offset Hanger Clamp Spec Sheet 13) Install protective surfacing before users are allowed to play on the structure. EC00100136 Dxummi 2130trm,eplace 201a21 m. Repliedhwdu epackage. -n CD I 4 Cid I � n Os r— M 7D O W EC00100136 Dxummi 2130trm,eplace 201a21 m. Repliedhwdu epackage. jl/y t landscape structures` Typical PlayBooster Post I ; Top o1�� clamp X (8) a/i' x 7 /41 BHCS w/Pin w/ a/," SAE F Washers I i I i ' I I I , I Step Section (4 -Step Shown) DETAIL PANEL TO DECK ATTACHMENT (4) Pariah Qom{ (4) a/a" x r/a" BHCS w/Pin w/'/j' SAE Flat Washers PlavBoostel SAFETY NOTE Clwose a pmtaUlw svleo,tg material mat has a Critical Height Value of at leas) the IS014001 i M g atneageg seq ama l(ae� s u Cer'I lietl F14B]) 15312400 DETAIL PANEL TO CLAMP ATTACHMENT (4) Typical Offset Hanger Clamp -,- Assemblies (4)'/f' Flange` Nuts w/Pin . f 152907A -1 STEP: 16" DECK HEIGHT DIFFERENCE 152907B -2 STEPS: 24" DECK HEIGHT DIFFERENCE (4)'/;' Standard 152907C - 3 STEPS: 32" DECK HEIGHT DIFFERENCE Hex Nuts SAE Flat Washers W152907D - 4 STEPS: 40" DECK HEIGHT DIFFERENCE 152907 Deck Link, w/ Barriers Sheet 1 ore 02008 by Landscape Structures All rights e,a.r I Document BHCS w/to =7e' / SAE Flat Washers 4) lubes DETAIL (2) Barriers (4) Panels STEP SECTION TO DECK ATTACHMENT Dock ------- ---'`(8)'/e" o (8) 1/,"Standard Hex Nuts w/'/," / SAE Flat Washers (2) Lower Panels _ n St �r Se n Q1 (8)'/i . x Iv;. `�W*,��.TML�,�r•Tji' �j�CS w/Pin tTt P. r rY+/ °/e" SAE r Washers �. It , vCil t � I I ' I � I wg NOTE:- " o �� These lower deck posts must be next longer -__ =_-- --- length than standard deck height posts and two lengths longer than . standard height roof posts. Top 01 Deck f 152907A -1 STEP: 16" DECK HEIGHT DIFFERENCE 152907B -2 STEPS: 24" DECK HEIGHT DIFFERENCE (4)'/;' Standard 152907C - 3 STEPS: 32" DECK HEIGHT DIFFERENCE Hex Nuts SAE Flat Washers W152907D - 4 STEPS: 40" DECK HEIGHT DIFFERENCE 152907 Deck Link, w/ Barriers Sheet 1 ore 02008 by Landscape Structures All rights e,a.r I Document 9/1. landscape structures Parts List PlayBooster{" 152907 Deck Link, w/ Barriers Part# Description Qty. 144696 1 -Step Section, Specify Color .................................. 1 144698 2 -Step Section, Specify Color .................................. 1 144700 3 -Step Section, Specify Color .................................. 1 144702 4 -Step Section, Specify Color .................................. 1 144703 1 -Step Barrier, Specify Color ................................... 2 144705 2 -Step Barrier, Specify Color ................................... 2 144707 3 -Step Barrier, Specify Color ................................... 2 144709 4 -Step Barrier, Specify Color ................................... 2 153896 Lower Panel, Specify Color ...................................... 2 153895 Upper Panel, Specify Color ...................................... 2 113468 Spacer Tube, Specify Color ...................................... 4 100610 '/," x 1/." Drive Rivet, AL/SST................................. 4 105327 5" Half Clamp, Specify Color .................................. 4 113729 Offset Hanger Clamp, Specify Color ....................... 4 156283 Deck Link Barr/Hrail Hardware Package.......... 1 100168 3/." x 3 '/," BHCS, SST ............................................. 4 100196 3/," x'/." BHCS w/Pin, SST .................................... 12 100198 14" x 1 Y." BHCS w/Pin, SST ................................. 16 100327 3/." Standard Hex Nut, SST ..................................... 12 100351 3/." Tee Nut, SST ........................................................ 8 100353 3/," Flange Nut w/Pin, SST ....................................... 4 100365 % SAE Flat Washer, SST ....................................... 36 Specifications Panels: Zinc plated 7 GA. (.179") HR flat steel. Finish: ProShield', color specified. Step Section: Formed from 12 GA (.105) sheet steel conforming to ASTM A 1011. Standing surface is 24 3/," wide x 14" en O deep and is perforated with 3/16" diameter holes. Fin- ish: Tenderfuff, color specified. Barrier: Weldment comprised of 1.125" O.D. x 11 Ga. (.120" CT wall) steel tubing, '/," O.D. steel bar with 203 or 303 stainless steel inserts with 34" internal threads. Finish: rn TenderTuff, color specified. SpacerTube: Made from 6061-T6 aluminum '/," O.D. x 1 "/16". T. Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specil' ions). Installation Time: Approx. 1 '/1 man hours Weight: I -Step - 130 tbs. 2 -Step - 182 tbs. 3 -Step - 236 lbs. 4 -Step - 296 lbs. Fall Height: Deck Height Installation Instructions I) Attach step section to decks using 3/e" x 1'/a" BHCS w/pin with 3/6" SAE flat washers and %" standard hex nuts with 3/," SAE flat wash- ers, as shown. Refer to the Step Section To Deck Attachment Detail. 2) Attach upper and lower panels to the face of the deck using 3/s" x'/s" BHCS w/pin with 3/," SAE flat washers and 3/," standard hex nuts with %" SAE flat washers. Refer to the Panel to Deck Attachment Detail. 3) Attach offset hanger clamps to posts at heights shown using 5" half clamps, 3/." x 1 '/," BHCS w/pin with 3/a" tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 4) Attach upper and lower panels to offset hanger clamps using Y." x 3'/4" BHCS with 34" SAE flat washers, spacer tubes and 3/s" flange nuts w/pin. Refer to the Panel To Clamp Attachment Detail. 5) Attach barriers to upper and lower panels using 3/." x'/," BHCS w/pin and 3/," SAE flat washers, as shown. 6) Install'/," x %" drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 7) Install protective surfacing before users are allowed to play on the structure. Eco Mom nxu,"eot M1562861)() rcPl M15312.00.Aaaed Y: xII', BHCS w/ to a advert pwkage. N a CD �n Z en O -- �� CT r rn T. o T� O W Eco Mom nxu,"eot M1562861)() rcPl M15312.00.Aaaed Y: xII', BHCS w/ to a advert pwkage. U V & landscape structures-, PLAN VIEW/FOOTING LAYOUTS FOOTINGS/ 1 -STEP Deck Deck FOOTINGS/ 3 -STEP RfRffRff mi mi Mi iffmoffmmm [a 0 2008 by Landscape Swcwres All rights reserved Deck FOOTINGS/ 2 -STEP 31 O_ O vt 'O O ,M FOOTINGS/ 4-S�F�P :�� r . M. 77�_ m iirG11 Deck Deck 152907 Deck Link, w/ Barriers 153124a Sheet 2 of 2 j & landscape structures Typical , (2)3/;' Flar PlayBooster (2)Handhold h--4 Nuts w/Pin Post Panels I URSe1 I V) / Hanger (2) 7/;' O.D. x 1 "/ Clamp Spacer Tubes Assemblies I I I , I 48"-72"' Deck Croqu Climbs I ' I , ' I (2) 3/e' Standard ' Hex Nuts w/ 3/;' Flat Washers I I I I , � I , I I I i I I I (2) Handhok Panels Protective Surfacing DETAIL PANEL TO CLAMP ATTACHMENT (2)Typical Offset Post Hanger Clamp DETAIL CROQUET CLIMBER ATTACHMENT Deck I i I i I I / (4) still x 7/l BHCS w/Pin w/ 3/e' Flat Washers (2) Handhold Panels (2) 3/," x 3 3/ BHCS w/Pin (2) 3/;' x 1 '/;' BHCS w/Pin w/ 3/e' SAE Flat Washers DETAIL fiAFETY NOTE -- lWaung material Nei Choose a protective sW PANEL TO DECK_; has a Cf tihel ue o least 0e Veale 14UU1 Highest si lat e height of the Highest Accessihl• 1. .11 IS0 MapM MNe agacent equipmaix (Ref. ASTu :IIIIeJ F1487.) /Pin 17608200 Typical , (2)3/;' Flar PlayBooster (2)Handhold h--4 Nuts w/Pin Post Panels I URSe1 I V) / Hanger (2) 7/;' O.D. x 1 "/ Clamp Spacer Tubes Assemblies I I I , I 48"-72"' Deck Croqu Climbs I ' I , ' I (2) 3/e' Standard ' Hex Nuts w/ 3/;' Flat Washers I I I I , � I , I I I i I I I (2) Handhok Panels Protective Surfacing DETAIL PANEL TO CLAMP ATTACHMENT (2)Typical Offset Post Hanger Clamp DETAIL CROQUET CLIMBER ATTACHMENT Deck I i I i I I / (4) still x 7/l BHCS w/Pin w/ 3/e' Flat Washers (2) Handhold Panels (2) 3/," x 3 3/ BHCS w/Pin (2) 3/;' x 1 '/;' BHCS w/Pin w/ 3/e' SAE Flat Washers DETAIL PANEL TO DECK_; ATTACHMENT Flange /Pin p C.n r • e y, 176077 Croquet 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888-4384574 L51 Direct 763-972-5200 Int. FAX (763) 972-3185 Document #17608200 Parts List PlayBooster®176077 Croquet Climber, 48"-72" Deck Part# Description Qty. 100610 '/," x'/," Drive Rivet, AUSST................................. 2 105327 5" Half Clamp, Specify Color .................................. 2 113468 '/," O.D. x I "/,a" Spacer Tube, Specify Color ...... 2 113729 5" Offset Hanger Clamp, Specify Color .................. 2 139563 Handhold Panel, Specify Color ................................ 2 176202 48"-56" Croquet Climber, DB, Specify Color ........ 1 175792 64"-72" Croquet Climber, DB, Specify Color........ 1 176111 48" Croquet Climber, SM, Specify Color ............... 1 176112 56" Croquet Climber, SM, Specify Color ............... 1 176113 64" Croquet Climber, SM, Specify Color ............... 1 176114 72" Croquet Climber, SM, Specify Color ............... 1 176385 Croquet Climber Hardware Package .................. 1 100196 1/," x 7/," BHCS w/Pin, SST ..................................... 4 100198 '/," x 1 Y.' BHCS w/Pin, SST .................................. 6 100327 1/," Standard Hex Nut, SST ...................................... 2 100351 3/," Tee Nut, SST ........................................................ 4 100353 1/," Flange Nut w/Pin, SST ....................................... 6 100362 3/," Flat Washers, SST ............................................... 6 100365 1/," SAE Flat Washers, SST ...................................... 2 124460 3/," x 3 3/," BHCS w/Pin, SST .................................. 2 111392 2 -Hole (SM) Hardware Package ........................... 1 100266 1/1" x 2 1/," Expansion Anchors ................................ 2 100322 '/1" Standard Hex Nut, SST ...................................... 2 100363 1/," Flat Washer, SST ................................................. 2 DB - Direct Bury SM - Surface Mount Specifications Croquet Camber: Weldment comprised of 2.375" O.D. RS20 (.095"- .105" wall) galvanized steel tube. 1.029" O.D. RS20 (.070"-.080" wall) galvanized steel tube, and'/," HRPO steel sheet. Finish: ProShield', color specified. Handhold Panel: Pennalene', color specified. Spacer Tube: Made from 6061-T6 aluminum 7/," O.D. x I Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SSI) perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: SM- Approx. l'/_ man hours DB - Approx. 2 man hours Concrete: DB - Approx. 1.31 cu. R Weight: DB 65 lbs. (48"-56") DB 68 lbs. (64"-72") SM 57 His. (48") SM 58 His. (56") SM 63 Its. (64") SM 64 lbs. (72') Fail Height: Deck Height Installation Instructions 1) (Direct Bury) Dig footing hole spaced as shown. 2) Attach the handhold panels to the face of the deck, using 1/," x 7/," BHCS w/pin with 1/," flat washers and 3/," flange nuts w/pin. 3) Attach handhold panels to the offset hanger clamps, using 3/," x 3 3/," BHCS w/pin, Y." O.D. x 1 "/,," spacer tubes and 1/," flange nuts w/pin. Refer to the Panel Attachment Detail. 4) Attach offset hanger clamps to posts, using 5" half clamps, 3/," x 1 '/," BHCS w/pin and 1/," tee nuts. Refer to the Typical Offset Hanger Clamp Spec Sheet. 5) Attach Croquet climber to deck, using 1/," x I'/e' BHCS w/pin with SAE flat washers and Y." standard hex nuts with 1/s' flat washers. 6) Install'/," x 3/," drive rivets in all 5" half clamps. Drill through hole in 5" half clamp and into 5" post with a'/," or "F" (only) drill bit, insert drive rivet into hole through clamp and into post. Hammer drive rivet pin in until flush with head. Refer to the Typical Offset Hanger Clamp Spec Sheet. 7) (Direct Bury) With Croquet climber plumb, pour concrete footing. Allow concrete footing to cure for a minimum of 72 hours before users are allowed to play on the structure. (Surface Mount) With Croquet climber plumb, drill '/1" x 3" deep holes through mounting plates using hammer drill and 1/1" masonry bit. Tap expansion anchors into drilled holes. Fasten mounting plates to expansion anchors, using'/_" standard hex nuts with'/1" flat wash- ers. 8) Install prolective surfacing before users are allowed to play on the component. N o_ O r" O 4 C -) -G li+ r <m a, M � �7C = O Q c:) N j & landscape structures - PLAN VIEW/FOOTING LAYOUT 50'/,-/1280 (94"42 L)OM) SAFETY NOTE Choosa a O 0,_,ve awtaang Mal-a,0a, hae a on, Haigh value of et least the h.'gM , ,he Hlgheri AmessiEle Pan/Fall HMyM or Mie sOjacen, eµnpmxa. (Ref ASTM F11BT.) N O DETAIL DIRECT BURY !o Croquet -74" DETAIL Climber SURFACE MOUNT Loose Fill Protective (2)'/i' Standard-- _ ,Croquet Croquet Surfacing - Hex Nuts w/ 11, Climber Flat Washers = (2)'/,' x 231," Subgrade •`'e Expansion •- Anchors °J Crushed �•' `•` Rock Concrete o NOTE: Sufficient protec- tive surfacing must cover hardware to satisfy fall Crushed height requirements. Rock I, 12" SAFETY NOTE Choosa a O 0,_,ve awtaang Mal-a,0a, hae a on, Haigh value of et least the h.'gM , ,he Hlgheri AmessiEle Pan/Fall HMyM or Mie sOjacen, eµnpmxa. (Ref ASTM F11BT.) 176082A 176077 Croquet Climber, 48"-72" Deck Sheet 2 of 2 02011brianos�ve Stu,W,es. Anhghtsmse,ven Document#17608200 N O —, !o -74" rn 'JP cn 176082A 176077 Croquet Climber, 48"-72" Deck Sheet 2 of 2 02011brianos�ve Stu,W,es. Anhghtsmse,ven Document#17608200 J1114, landscape structures` (2)Typical---A Offset Hanger Clamp Assemblies PlavBoosterO 176078 Lcilli reserved 1 11 C Efl71FIEU SAFETY NOTE Chpose a prolective s,matirg material ,n2( rias a CMical Height -,.e of at least ne hepht of the Highest Accessi11. Pa V.1 HegM of Ne actaxn, epuprwxp (Ref.ASTM Fr4BZ� 17608400 DETAIL PANEL ATTACHMENT -"� (2)TYpicalOffset (2)3/," Fla Hanger Clamp Nuts w/Pin Assemblies (2) Handhold Panels (2) 7/e' O.D. x 1 t1/,a' Spacer Tubes DETAIL LOLLIPOP CLIMBER r Lollipop a, Deck _ Climber (2) 3/e' Standard \• Hex Nutsw/ 3/s' Flat Washers DETA� PANEL TO f ATTACHM) 111111111111IM0 (2) Handhold \\ , Panels , i I (4) °/a" x a/, BHCS w/Pin w/ 3/," Flat .n Washers Protective Surfacing Climber, 48"-72" Deck " x 3 3/4" S w/Pin (2) 3/f' x 1 1/," BHCS w/Pin N w/ 3/," SAE c Flat Washers rr o i C ,DD.eck I{� / 'ri (4) 3/, Flange Nuts w/Pin Sheet 1 of 2 Document #17608400 (1„ PlayBooster"' 176078 Lollipop Climber, 48"-72" Deck landscape structures* Parts List Installation Instructions Part# Description Qty. 100610 '/4" x 3/," Drive Rivet, AUSST................................. 2 105327 5" Half Clamp, Specify Color .................................. 2 113468 7/," O.D. x 1 "/„' Spacer Tube, Specify Color ...... 2 113729 5” Offset Hanger Clamp, Specify Color .................. 2 139563 Handhold Panel, Specify Color ................................ 2 175873 48"-56" Lollipop Climber, DB, Specify Color....... 1 175871 64"-72" Lollipop Climber, DB, Specify Color....... 1 176115 48" Lollipop Climber, SM, Specify Color .............. 1 176116 56" Lollipop Climber, SM, Specify Color .............. 1 176117 64" Lollipop Climber, SM, Specify Color .............. 1 176118 72" Lollipop Climber, SM, Specify Color .............. 1 176384 LoWpop Climber Hardware Package .................. 1 100196 '/," x 7/," BHCS w/Pin, SST ..................................... 4 100198 3/," x 1 '/," BHCS w/Pin, SST .................................. 6 100327 '/," Standard Hex Nut, SST ...................................... 2 100351 3/," Tee Nut. SST ........................................................ 4 100353 '/," Flange Nut w/Pin, SST.... ................................... 6 100362 '/," Flat Washers, SST ............................................... 6 100365 %" SAE Flat Washers, SST ...................................... 2 124460 3/," x 3 3/," BHCS w/Pin, SST .................................. 2 111392 2 -Hole (SM) Hardware Package ........................... 1 100266 1/2" x 2'/," Expansion Anchors ................................ 2 100322 '/2" Standard Hex Nut, SST ...................................... 2 100363 'A" Flat Washer, SST ................................................. 2 DB - Direct Bury SM - Surface Mount Specifications Lollipop Climber: Weldment comprised of 1.315' O.D. RS20 (.080% .090" wall) galvanized steel tube, 2.375" O.D. RS20 (.095"-.105" wall) galvanized steel tube, '/," HRPO steel sheet and 10 GA. (.135") HRPO steel- Finish: ProShield", color specified Handhold Panel: Permalener, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/." O.D. x 1 Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: SM - Approx. I '/r man hours DB - Approx. 2 man hours Concrete: DB - Approx. 1.31 cu. ft. Weight: DB 63 lbs. (48"-56") DB 71 lbs. (64"-72') SM 59 lbs. (48") SM 60 lbs. (56") SM 66 lbs. (64") SM 68 lbs. (72") Fail Height: Deck Height 1) (Direct Bury) Dig footing hole spaced as shown. 2) Attach the handhold panels to the face of the deck using'/," x 7/." BHCS w/pin with 34" flat washers and'/," flange nuts w/pin. 3) Attach handhold panels to the offset hanger clamps, using'/r" x 3 3/," BHCS w/pin, %" O.D. x 1 "/,," spacer tubes and'/." flange nuts w/pin Refer to the Panel Attachment Detail. 4) Attach offset hanger clamps to posts at height shown using 5" half clamps, 3/," x 1 '/," BHCS w/pin and 3/," tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 5) Attach Lollipop climber to deck, using'/." x I'/," BHCS w/pin with '/," SAE flat washers and'/," standard hex nuts with 3/," flat washers. 6) Install'/," x 3/," drive rivets in all 5" half clamps. Drill through hole in 5" half clamp and into 5" post with a '/4" or "F" (only) drill bit, insert drive rivet into hole through clamp and into post. Hammer drive rivet pin in until flush with head. Refer to the Typical Offset Hanger Clamp Spec Sheet. 7) (Direct Bury) With Lollipop climber plumb, pour concrete footing. Allow concrete footing to core for a minimum of 72 hours before users are allowed to play on the structure. (Surface Mount) With Lollipop climber plumb, drill 'A" x 3" deep holes through mounting plates using hammer drill and'/t" masonry bit. Tap expansion anchors into drilled holes. Fasten mounting plates to expansion anchors, using 1/." standard hex nuts with'/," flat wash- ers. 8) Install protective surfacing before users are allowed to play on the component. N 0 `S2 C:) "}71 , t D -i -- t C7� 1 fit- a ITl CTI 70 = ax o O fV U landscape structures, PLAN VIEW/FOOTING LAYOUT 50'/4-/1280 (54"-72' UeCKS) DETAIL SURFACE MOUNT Standard-- He NLollipop Hex Nuts w/ /," Climber Flat Washers (2)'12" x 2 3/," Expansion Anchors Concrete Crushed Rock DETAIL DIRECT BURY Loose Fill 176078 ••••Climber,48"-72" Deck _ et 2 of 2 .NO. MINNESOTA 553288605 888.574-4678 L51 Install Help 888438,8574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 Document •08.00 N O C V1 Sn O - Y --4 ? Eo n t c — a {r m M C3 _a s 0 D' cn < uT NOTE: Sufficient protec- 176078 ••••Climber,48"-72" Deck _ et 2 of 2 .NO. MINNESOTA 553288605 888.574-4678 L51 Install Help 888438,8574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 Document •08.00 4.- n Subgrade a.:.. e ? Eo _ c — a Concrete— < v NOTE: Sufficient protec- tive surfacing must cover hardware to satisfy fall Crushed— ' height requirements. Rock 176078 ••••Climber,48"-72" Deck _ et 2 of 2 .NO. MINNESOTA 553288605 888.574-4678 L51 Install Help 888438,8574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 Document •08.00 A& landscape structures• (2),/." x 2 /4 BHCS w/Pin 64"-72" Deck (2) Typical \ Offset Hanger Clamp Assemblies Sunbeam Climber Typical Offset Hanger Claml Assembly N DETAIL Sunbeam —} I Climber I (2)'/." x 1 '/,' BHCS w/Pin w/ It," SAE (2)'/,' Standard Flat Washers Hex Nuts w/'/,' Flat Washers 'IayBoostere 176079 Su 0 2011 by Lantlsoape Struclures. All rights reserve. SAFETY NOTE Choose a protecays surfai h alerial 1-1 has a Critical Height Value of at lea isast the height of the Highest A�ss all IS014001 Heightoftheagacerdswrier Ina STM Cer'i 1F1487) (5)'/,' Flar Nuts w/Fin 141, w/Pin Panel 17608600 DETAIL INFILL PANEL ATTACHMENT Barrier w/'/, A BHCS w/Pin w!'/,' SAE Flat Washers 114"O.D.xI Spacer Panel ;FTAILo —� �61TJ�1C�AENT— r J�' 3 / UBq' BHCS BHCS w/Pin Standard w/'!;' SAE x Nut w/'/," Flat Washer 2 Flat Washer DETAIL CLIMBER/BARRIER ATTACHMENT 1 '/," 0. D. x 7/,' SPacer---,gr--��Barrier '/;' Standard— Hex Nut w/ 3/1 Flat Washer Sunbeam Climber Climber DETAIL CLIMBER TO POST AT rACHIMME\NT / PI oat I \ '/," x 2 1/1 BHCS w/Pin w/'1;' SAE Flat Washer (2) 5" Half Clamps (4) '/," Tee Document#17608600 (4)'l," x 71,"_ BHCS w/Pin Protective w/'/," SAE Surfacing Flat Washers DETAIL CLIMBER TO POST AT rACHIMME\NT / PI oat I \ '/," x 2 1/1 BHCS w/Pin w/'1;' SAE Flat Washer (2) 5" Half Clamps (4) '/," Tee Document#17608600 Jilin landscape structures, Parts List PlayBooster" 176079 Sunbeam Climber, 64"-72" Deck Part# Description Qty. 100610 1/4" x'/," Drive Rivet, Al./SST................................. 5 105327 5" Half Clamp, Specify Color .................................. 5 108542 Handloop, Specify Color ........................................... 1 113729 5" Offset Hanger Clamp, Specify Color .................. 3 151072 1 '/," O.D. x 1 V." Spacer, Specify Color ............... 1 170930 Barrier, Specify Color ............................................... 1 170931 Barrier Infill Panel, Specify Color ........................... 1 176050 Sunbeam Climber, Specify Color ..... ._._._._...._..... 1 176344 1 '/," O.D. x'/," Spacer, Specify Color..... .............. 1 176386 Sunbeam Climber Hardware Package ................ 1 100196 14" x 1/," BHCS w/Pin, SST ..................................... 9 100198 3/," x 1'/," BHCS w/Pin, SST .................................. 8 100199 3/r" x 2'/4" BHCS w/Pin, SST ... .............. I ............. ... 2 100203 1/," x 2'/," BHCS w/Pin, SST .................................. 3 100327 1/," Standard Hex Nut, SST ...................................... 4 100351 1/," Mod T -Nut, SST ................................................. 10 100353 1/,' Flange Nut w/Pin, SST ....................................... 5 100362 1/," Flat Washer, SST ................................................. 4 100365 1/," SAE Flat Washer, SST ....................................... 13 Specifications sunbeam Climber. Weldment comprised of 1.315" O.D. RS20 (.080"- .090" wall) galvanized steel tube, 2.375" O.D. RS40 (.130"-.140" wall) galvanized steel tube, and 1/4" HRPO steel sheet. Finish: ProShieldx, color specified. Barrier: Weldmem comprised of 1.125" O.D. 11 Ga (.120") steel tube per ASTM A513 with 203 or 303 stainless steel threaded insert with 1/," internal threads and 1/4" tabs. Finish: TenderTuft , color specified. Handloop: Weldment comprised of 1.125" O.D. 1 I GA (.120") steel tubing with 203 or 303 stainless steel inserts, with 14" internal threads. Finish: TenderTuR, color speci- fied Infill Panel: Pennalene°, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 1 '/4 man hours Weight: 118 lbs. Fall Height: Deck Height Installation Instructions 1) Attach Sunbeam climber to deck, using'/," x I Y." BHCS w/pin with 34" SAE flat washers and'/," standard hex nuts with'/," flat washers. Refer to Detail. 2) Attach Sunbeam climber to post, using 5" half clamps, 3/,' x 3/,' BHCS w/pin with 1/," SAE flat washers and 3/,' tee nuts. Refer to Climber To Post Attachment Detail. 3) Place 1 '/," O.D. x 1/," spacer between barrier tab and Sunbeam Climber. Attach barrier, 1 '/," O.D. x r/," spacer and Sunbeam Climber to deck, using 3/,' x 2'/4" BHCS w/pin with 3/," SAE flat washer and 3/," standard hex nut with 3/," flat washer. Refer to the Climber/Bar- net Attachment Detail. 4) Place 1 '/," O.D. x 1 '/," spacer between barrier tab and deck. Attach barrier and 1 '/," O.D. x I '/," spacer to deck, using 3/," x 2'/4" BHCS w/pin with 3/," SAE flat washer and 3/," standard hex nut with 3/," flat washer. Refer to the Barrier Attachment Detail. 5) Attach barrier to offset hanger clamp, using'/." x 2'/4" BHCS w/pin. 6) Attach infill panel to barrier, using 3/," x'/," BHCS w/pin with %" SAE flat washers and 3/," flange nuts w/pin. Refer to the Infill Panel At- tachment Detail. 7) Mark locations for clamps on posts per dimensions on front of sheet. Attach offset hanger clamps to posts, using 5" half clamps, 3/," x 1 '/," BHCS w/pin and 1/," tee nuts. Refer to the Typical Offset Hanger Clamp Assembly Sheet. Attach handloop to offset hanger clamp as- semblies, using 1/," x 2 '/4" BHCS w/pin. 8) Install 14" x 1/," drive rivets in all 5" half clamps. Drill through hole in 5" half clamp and into 5" post with a'/," or "F" (only) drill bit, insert drive rivet into bole through clamp and into post. Hammer drive rivet pin in until flush with head. Refer to the Typical Offset Hanger Clamp Spec Sheet. 9) Install protective surfacing before users are allowed to play on the structure. t;9_ E5 n D -I cn n -f -� C-)--) tT r ;< m a rn C:)� S O Q v o N A& landscape structures• 11:11f1llll (4)'4" x a/;" NET CLAM Drive Rivets (4)'/e" O.D. x'/; Post Bushings (8)'/e" Tee Nuts W/ V.11 Jam Nuts BHCS w/Pin (4) '/," x '/a' BHCS w/Pin Limited Thread 72" Deck ,rh VO 6 O NOTE: Top of first tread needs to be level with top of deck. Adjust supports as needed to make level. (16)'/1;'x2'/+d" DETAIL BHCS w/Pin Limited Thread Bolts (16)'/;' x 1 BHCS w/Pin Limited Thread Bolts } (16)'/;' 0. D. x 3/ ------ (32)'/;' Lot, Bushings Crown Cap Nuts w/'/;' NOTE: Do not over SAE Flat tighten bolts, make Washers sure Trapeze Bars (B)Trapeze movefreely. Bars 5" Half Net Nets (2) Betts (2) Belt Tabs NOTE gram Choose a protective Y NOTg material that has a Chhi i Height Wore of at least the IO 14001 height of Vie Highest AwesatWe ParWall Megvame ageam agiipriwt (Ref. Asnw Certified Flat) 20062000 DETAIL CABLEATTACHMENT (28) a/;' 0. D. x'/a"- Long Bushings (28)'/;' X'/a"— BHCS w/Pin Limited Thread (32)'/e" x 1 1/z" FHCS w/Pin\ -Lower Beam Double O 2015 by LeMsc iae &m W es. All rights reserved. Supports (2) Nets (8)'/a" x 11/$ BHCS w/Pin Supports ower Beam 3UPPORTATTACHMENT 7POst4) 1/4" x'/; Drive Rivets (8)'/;' Tee Nuts (4) a/". x 3'/;' (8) Treads BHCS w/Pin (4) Spac70amp Tubes (4 HA (4)'/a" Flange Vpg6, Nuts w/Pin Protective Surfacing Lower Beam Sheet 1 of 3 Document #20811500 (8) Treads Low Bea (4) a/". x 3'/;' (8) Treads BHCS w/Pin (4) Spac70amp Tubes (4 HA (4)'/a" Flange Vpg6, Nuts w/Pin Protective Surfacing Lower Beam Sheet 1 of 3 Document #20811500 J & landscape structures, Post 72" Deck (4) Handhold Panels \ As 1 1 1 CERTIFIED DETAIL BELT TAB ATTACHMENT SAFETY NOTE Choose a goteGiva surtaarq mabnal Mat hes a CnUwl Height Veale of et besl the height of qw Nighasl Acceuide PaNFall HegadMe agaceraequipner2 (Rel ASPM F11a1) (6)'/a' x 1'/a' BHCS w/Pin wI'/;' Flat Washers I T (2) Decks (2) Belt Tabs (6)3/;' Low -- Crown Cap Nuts w/'/e' Flat Washers (8)'/;' Standard (8) 3/j' x 1 t/;' Nuts BHCS w/Pin Hex HexFlat w/'/;' SAE Flat Washers Washers (Large) (Small) DETAIL BELTATTACHMENT (4) a/aex 54"Tread BHCS w/Pin w/ I&" Flat (4) %" Flange Nuts w/Pin NOTE: Attach belt with textured surface up. 208115a NOTE: Top of first tread needs to be level with top of deck. Adjust supports as needed to make level. Lower Beam Dn --1 n� m r �M q ^ V 'y 7C p y o N • i ") 200609 Traveler Climber 6017TH S I REST SOUTH. DELANO, MINNESOTA 55328-8605 888.5744878 LSI Install Help 888-438-6574 LSI Direct 76"7Z.5200 Int. FAX (763) 972.3186 I S & landscape structures` Top of Clamp -w of peck (4) 3/," x 3/e BHCS w/Pin w/3/;' Flat Washers (Large) PlayBooster� ® 2015 oy Larfdscape Stmdures. All nghU reser dxJ (4) Handhold Panels Of SAFETY NOTE CnWSe a prolective surta0!`7 malPnal Nal nas a CnVcal Heignl Value of it leas)d I�O 140U1 , height of Ire Highest Ac ese ie PaNFall Certified F14BZHeigfdo/Ne aQaced 6quipmant (Ref.A5TA1 2006200 (4)Typical Offs Hanger Clamp Assemblies (4)3/a' Flange - Nuts w/Pin (4) Sp Tubes DETAIL PANELATTACHMENT / (4)'/."x3/e Drive Rivets (4) Handhold (4) 3/01' x 3 3/4" Panels BHCS w/Pin 3/a' Flange s w/Pin 200609 Traveler Climber _o C-) O I n-< 1 --1 n Q1 .<rM A i � l 72" � 3 Deck to CA 3/a' Flange s w/Pin 200609 Traveler Climber j & landscape structurev 1 1 1 CERTIFIED SAFETY NOTE Choose a prdecUve surf., ,"renal that has a Critical Height value of el least the he of the Highest Amessible paNFall Height of the agacent equipment (Ref ASTM F-,, 200620b Finished Grade DETAIL HANGER BRACKET ATTACHMENT NOTE:Ahangerbracketis44eHan7ger anger Bracket o required when there is not rs a lower deck at the end of �n o the TravelorClimber. --1rJm:<r—a(2) 5" Half m x Clamps ; Q D o N Booster° C 2015 by Lan scape Stmnures All nghts resents %" Patch Nuts '!e" Flat Washers 200609 Traveler Climber 1 landscape structures Parts List Part# Description Qty. 100610 '/." x 5/e" Drive Rivet, AL./SST ............................... 12 105327 5" Half Clamp, Specify Color .................................. e 113729 5" Offset Hanger Clamp, Specify Color .................. 4 106022 Deck Hanger Clamp, Specify Color ........................ a 113468 '/e' O.D. x I "/1s" Tube, AL., Specify Color .......... 4 144476 Handhold Panel, Specify Color ................................ 4 161898 Net Clamp, Specify Color ......................................... 4 190911 Upper Support, Specify Color .................................. 2 202759 Net (Cable Assy.), Black, Specify Color ................. 2 194917 Lower Beam, Specify Color ...................................... 1 195007 Trapeze Bar, Specify Color ....................................... 8 201922 Belt, Black.................................................................. 2 201971 Belt Tab, Specify Color ............................................. 2 202034 GripX Tread, Black .................................................... 8 184259 Hanger/Transition Bracket, Specify Color ............. 208121 Traveler Climber Hardware Package .................. 1 100196 '/5" x'/," BHCS w/Pin, SST ..................................... 4 100198 '/.' x 1 I/a" BHCS w/Pin, SST ................................. 38 151421 3/r" x 1 11r" FHCS w/Pin, SST ........................ I......... 32 100290 1/a" x'/: BHCS w/Pin Limited Thread, SST ........ 32 100292 x 11/1" BHCS w/Pin Limited Thread, SST...... 16 100349 1/r" Low Crown Cap Nut,SST................................. 38 100351 % Tee Nut, SST ....................................................... 24 100353 1/r" Flange Nut w/Pin, SST ...................................... 12 100327 '/r" Standard Hex Nut, SST ...................................... 8 100362 3/." Flat Washer, SST ................................................ 28 100365 1/1" SAE Flat Washer, SST ....................................... 40 124460 3/a" x 3 3/"" BHCS w/Pin, SST .................................. 4 127068 1/16" x 2.438" BHCS w/Pin Limited Thread, SST. 16 127179 5/a" O.D. x 1/8" Long Bushing, SST ......................... 48 138917 Double Clevis, SST ................................................... 16 128296 1/a" Jam Nuts, SST .................................................... 16 100195 1/e" x 5/1" BHCS w/Pin, SST ..................................... 4 106676 Hanger Bracket Hardware Package .................... 100198 1/r" x 1 1/r" BHCS w/Pin, SST .................................. 4 100321 3/a" Hex Patch Nut, SST ............................................ 2 100351 3/a" Tee Nut, SST ........................................................ 4 100362 1/a" Flat Washer, SST ................................................. 2 100610/:' x 5/5" Drive Rivet, AL/SST................................. 2 Quantity Determined By Year Order PlayBooster"' 200609 Traveler Climber Specifications Lower Beam: Weldment comprised of 1.900(48,26mm)O.D.RS20 (.090"-.100") (2,29 mm -2,54 mm) galvanized steel tub- ing, 1.315 (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,29 mm) galvanized steel tubing. 7 GA. (.179") (4,55 mm) HRPO steel sheet,'/s" (3,18 mm) HRPO steel sheet and %" (9,53 mm) thick HRPO steel sheet. SAE 841 dry bronze bushings are pressed into hous- ings at factory. Finish: ProShield', color specified. Trapeze Bar: Weldment comprised of 1.315"(33,40 ram) O.D. RS20 (.080"-.090") (2,03 rnm-2,29 man) galvanized steel tub- ing and 7 GA. (.179") (4,55 mm) HRPO steel sheet. Finish: ProShield, color specified. Cable Assembly: (Cable)Made of tightly woven polyester-wmpped,six- stranded galvanized -steel cable with a polypropylene core. (Cable Connectors) 6063-T6 aluminum. Hanger Bracket: Formed from 11 GA (.120") (3,05 mm) HRPO low Area Req: carbon sheet steel. Finish: TendciTuff, color specified. GripX Tread: 3/J' (19,05 mm) Thick Permalene", black in color. Handhold Panel: Permalene', color specified. Support: Weldment comprised of2.375"(60,33 mm) O.D. RS40 Max. Fall Height: (.130" - .140") (3,30 mm -3,56 mm) wall galvanized steel tubing,%" (9,53 mm) thick HRPO steel sheet, Eco 01W30 Dmwn,n 20x11500 reylam 20062000. Repa net and 1/4' (6,35 ram) HRPO flat steel. Finish: ProShield, color specified. Bek: .315" (8,00 mm) Thick mini rough top rubber belting with polyester fabric plys, black in color. Bek Tab: Weldment comprised of 1/d' (9,53 man) thick HRPO steel sheet, and 1Q' (6,35 man) HRPO Bat steel. Fin- ish: ProShield, color specified. Net Clamps: Weldment comprised of 1/4" (6,35 mm) x 1 1/4' (44,45 mm) HRPO Bat steel and .375" (9,53 mm) stainless steel sheet. Finish: ProShield, color specified. Clamp: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tam- perproof in design, stainless steel (SST) per ASTM F879 unless otherwise indicated (see specific product installation/specifications). Installation Time: Approx. 41/r man hours Area Req: 6'(1,83 m) minimum use zone Weight: 309 lbs. No Hanger Brackets �� 330 lbs. w/ 1 Hanger Brackets A 352 lbs. w/2 Hanger Brackets Max. Fall Height: 72" (1,82 m) `<r—r Ql 1 3 M �� A to (:Dpheet 3 of 3 y: --Document #20811500 cn Eco 01W30 Dmwn,n 20x11500 reylam 20062000. Repa net aatrpvelor seldmre pckase. kl�-, landscape structures' PlayBoosterl 200609 Traveler Climber Installation Instructions 1) Attach belt tabs and handhold panels to decks. Refer to the Belt Tab Attachment Detail. 2) Attach offset hanger clamps to handhold panels. Refer to the Panel Attachment Detail. 3) Attach offset hanger clamps to posts, using 5" half clamps and'/." x 1 '/," BHCS w/pin with 3/8" tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 4) Lay beam on ground with bushings facing up. Position double clevis's over bushings and fasten with'/,," x 2'/,6" BHCS w/pin limited thread bolts. See Detail. NOTE: Do not over tighten bolts. 5) Attach trapeze bars to double clevis's as shown, using bushings and 3/," x I '/." BHCS w/pin limited thread bolt. NOTE: Do not over tighten bolts, make sure trapeze bars move freely. 6) Tum lower beam over. Attach treads to lower beam. Refer to Detail. 7) Attach supports and net clamps to posts at height shown. Refer to the Support and Net Clamp Attachment Details. 8) Attach nets to clamps and supports. Refer to the Cable and Net Clamp Attachment Details. 9) Attach lower beam to nets. Refer to Details. NOTE: Top of first tread needs to be level with top ofdeck Adjust supports as needed to make level. 10) Attach belts to belt tabs and lower beam. Refer to the Belt Tab & Belt Attachment Details. 11) (If applicable - Hanger Bracket) Mark posts at 16" above finished grade. Attach deck hanger clamps to hanger bracket. Position hanger bracket with deck hanger clamps between posts level with marks. Attach to posts. Refer to the Hanger Bracket Attachment Detail. NOTE: A hanger bracket is required when there is not a lower deck at the end of the Travelor Climber. 12) Install '/," x `I," drive rivets in all 5" half clamps. Drill through hole in 5" half clamps and into 5" post with a'/," or" F" (only) drill bit, insert drive rivet in hole through clamp and into post. Hammer drive rivet pin in until flush with head. Refer to the Typical Offset Hanger Clamp Spec Sheet. 13) Install protective surfacing before users are allowed to play on the structure. O _o era C- COT D.{ --4 n-< I rn -t c, fir- rT1 o IV landscape structures° NOTE: When using this deck, ALL enclosures and components are mounted on the OUT- SIDE of the posts like the bubble panel shown above. 1 1 1 CERTIFIED 1070 DETAIL DECK HANGER CLAMP (8) a/a. x 1 va BHCS w/Pin (4)'/4" X % Drive Rivets (4) 5' Half Clamps 111228 Deck Post SAFETY NOTE Choose a protaMive surfial material that has a critical Height Value of at least the height of the Highest AcceasiEle PaNFall Heigh oftheaQe�M equpmenl. (Ref. ASTM F149IJ 14582100 (4) Deck Hanger Clamps (4)'/e" Flat Washers W/ 3/," Hex Patch Nuts uare Deck �r 1 rn 0 C 2004 by Lanasnp Structures. All rights reserved Document #14582100 N A zE- n -< m <rn a -n S (4)Stu(W tl1 cn _ (8)'/e" Tee (4) Deck Hanger Clamps (4)'/e" Flat Washers W/ 3/," Hex Patch Nuts uare Deck �r 1 rn 0 C 2004 by Lanasnp Structures. All rights reserved Document #14582100 U v(�1- landscape structures J:65PEM145114582100. P65 Parts List Pat U4 Description 145656-00 Tenderdeck, Specify Color .................... 105327-01 5" Half Clamp, Specify Color .............. 106022-00 5" Deck Hanger Clamp, Specify Color 119491-00 Hardware Package ............................... 100198-00 '/e" x I Y." BHCS w/Pin, SST .............. 100321-00 '/8" Hex Patch Nut, SST ........................ 100351-00 '/e" Tee Nut, SST .................................... 100362-00 '/r" Flat Washer, SST ............................. 100610-00 V," x 3/r" Drive Rivet, SST ................... Specifications Qty. .. 1 .. 4 .. 4 Square Deck: Flange formed from 12 GA (.105") sheet steel con- forming to ASTM A1011. Standing surface is perfa- rated With '46" diameter holes. Deck face has (4) slot- ted holes for face mounting components. The finished size measures 2'/a' x 47" x 47". Finish: TenderTuff111, color specified Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShielda, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproofin design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 1 man hour Weight: 119 lbs. PlayBooster" 111228 Square Deck Installation Instructions 1) Mark posts for the appropriate height of the deck you are installing. 2) Fasten hanger clamps to marked position on posts. See Detail on front of sheet. 3) Lift deck into position, lining up studs underneath deck with deck hanger clamp as shown. Attach with 3/r" Dat washers and'/a" hex patch nuts. 4) Level deck and plumb posts. Install the drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 5) After all enclosuros/components are installed, pour concrete foot- ings per the Typical Concrete Footing Detail Sheet. 6) Install protective surfacing before users are allowed to play on the structure. F M2264 nava"ik145821WO Imw#1395/600.Rgh Tmdn L N O O CD r r su z 0 0 rV j & landscape structures 0 r 0 Tenderdeck NOTE: When using this deck, ALL enclosures and components are mounted on the OUTSIDE of the posts. V 111229 OWN SAFETY NOTE Choose a protective surtaarg material Net �/� /�/� hes a Critical Height Value of at least the IS014001 , rbgma ne edHzgehnala9�P sntltlHe eASTaM ® Ce'11ed F11d]J 14582200 DETAIL Deck 4 Extension (4) 1/." x 1 1/e' BHCS w/Pin w/ (8)'/;' Flat Washers & (4)'/;' Standard Hex Nuts Tenderdeck Extension (2) Studs (2) Deck Hanger Clamps (4)'/e' Tee Nuts (2)'/;' Flat Washers &- 3/;' Hex Patch Nuts uare Extension Post x 1 1/a" w/Pin 5" Half 1/1. x s/e ve Rivets 02004 by Landscape Structures. All rights reserved Document #14582200 o_ O tri c+� n 1 J —I ""4 Ci 1 ic� m 'DET?QL DECK HANGER CLAMP (2) Studs (2) Deck Hanger Clamps (4)'/e' Tee Nuts (2)'/;' Flat Washers &- 3/;' Hex Patch Nuts uare Extension Post x 1 1/a" w/Pin 5" Half 1/1. x s/e ve Rivets 02004 by Landscape Structures. All rights reserved Document #14582200 Un landscape structures, J 1SPECS\145\14582200 P65 Parts List PlayBooster° 111229 Square Extension Part# Description Qty. 145661-00 Square Deck Extension, Specify Color ................... 1 105327-01 5" Half Clamp, Specify Color .................................. 2 106022-00 5" Deck Hanger Clamp, Specify Color ................... 2 106556-00 Hardware Package ................................................... 1 100198-00 '/a" x 1 V." BHCS w/Pin, SST .................................. 8 100327-00 '/s" Standard Hex Nut, SST ...................................... 4 100351-00 '/a" Tee Nut, SST ........................................................ 4 100362-00 3/a" Flat Washer, SST ................................................ 10 100610-00 1/4" x 3/a" Drive Rivet. AL/SST................................. 2 100321-00 '/a" Hex Patch Nut, SST ............................................ 2 Specifications Square Deck Extension: Flange formed from 12 GA (.105") sheet steel con- forming to ASTM A1011. Standing surface is perfo- rated with'/,a" diameter holes. Deck face has (4) slot- ted holes for face mounting components. The finished size measures 2'/a" x 42" x 47". Finish: TenderTufrTM, color specified. Deck Hanger Clamp Assembly: Cast aluminum. Finish: PraShielda, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx.I man how Weight: 106 lbs. Installation Instructions 1) Mark posts for the appropriate height of the deck you are installing. 2) Fasten hanger clamps to marked position on posts. See Detail on front of sheet. 3) Lift deck into position, lining up studs underneath deck with deck hanger clamp as shown. Attach with'/s" flat washers and'/s" hex patch nuts. 4) Attach extension to tenderdeck using'/a" x 1 1/8" BHCS w/pin with'/s" flat washers and'/." standard hex nuts. 5) Level deck and plumb posts. Install the L/411 x'/s" drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 6) After all enclosurestcomponents are installed, pour concrete foot- ings per the Typical Concrete Footing Spec Sheet. 7) Install protective surfacing before user; are allowed to play on the structure. F #52264 D"cummt#145822Wrep1 #13972000.Repl Ache im. N O GTl 0 �C —.j t 7— t7x 9 M a � 0 0 rd landscape structuress NOTE: The Tri -Deck Extension can attach to all other deck styles. 1 11 CERTIFIED Tenderdeck (4) 3/8' x 1 1/en BHCS w/Pin w/'/," Flat Washers SAFETYNOTE Choose a protective sunafirg material that has a Critical Hei9h1 Value of at least the height of the Highest Accessible ParUFall HegMofthe atljaoentequipmeM (Ref ASTM 1141' ) 14582600 DETAIL Deck V Extension (4)'/a' Standard Hex Nuts W/3 /," Flat Washers Tri -Deck Extension N O Q C1 •Ao�o chi Cn 1 DETAIL DECKHANGERCLAMP o = 0 �X %p Post D c cn 5" Half (2)'/e" Tee Nuts Clamp —Deck Hanger 1/4" x'/," Clamp Drive Rivet Hex Patch Nut w/'/," Flat (2)'/;' x 1 1/8" Washer BHCS w/Pin PlayBooster"' 119646 Triangular Tenderdeck Extension 1 0 2004 by Landscape Structures. All rights reserved Document #14582600 NOTE: When using this deck, ALL enclosures and components are mounted on the OUTSIDE of the posts. A& landscape structures• J\SPECS\145\14582600. P65 Parts List PlayBooster° 119646 Triangular Tenderdeck Extension Part# Description Qty. 145663-00 Tri -Deck Extension, Specify Color .......................... 1 105327-01 5" Half Clamp, Specify Color .................................. 1 106022-00 5" Deck Hanger Clamp, Specify Color ................... 1 119593-00 Tri -Deck Extension Hardware Package .............. 1 100198-00 '/." x 1 Y." BHCS w/Pin, SST .................................. 6 100321-00 1/1" Hex Patch Nut, SST ............................................ 1 100327-00 '/." Standard Hex Nut, SST ...................................... 4 100351-00 34" Tee Nut, SST ........................................................ 2 100362-00 '/," Flat Washer, SST ................................................. 9 100610-00 '/4"x'/s" Drive Rivet, AL/SST.................................1 Specifications Tri -Deck Extension: Flange formed from 12 GA (.105") sheet steel con- forming to ASTM A1011. Standing surface is perfo- rated with 5/,s' diameter holes. Deck face has (4) slot- ted holes for face mounting components. The finished size of two of the three sides measures 2 5/s" x 37 7/s" on the face ofthe deck and the other side measures 2'/s" x 43 3/4". Finish: TenderTuff' , color specified. Deck Hanger Clamp Assembly: Cast aluminum. Finish: ProShielda, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx.'/4manhour Weight: 52 His. Installation Instructions 1) Mark the post for the appropriate height of the deck you are install- ing. 2) Fasten the deck hanger clamp to the marked position on the post. Refer to the Deck Hanger Clamp Detail. 3) Lift the deck into position, line up the studs underneath the deck with the deck hanger clamp. Attach using a'/." hex patch nut and'/e' flat washer, as showa. 4) Attach the tri -deck extension to the tendmileck using %" x 1 '/a' BHCS w/pin with'/s" flat washers mid 1/8" standard hex nuts with flat washers. 5) With the tri -deck extension level and the post plumb, install the '/4" x '/e drive rivet in the 5" half clamp. Refer to the Typical Offset Hanger Clamp Spec Sheet. 6) Install protective surfacing before users are allowed to play on the structure. N O C:) S Y-1 Clf (7 ZA �-� I cn r <ra M Ma CD rV Ew#52268 orcwe"ia14581cO6rt #139xIM.tlwl Th -o kExu,,.im. landscape structures, 900 Triangular Tenderdeck llw� SAFETY NOTE Ctwase a prolective surtadng material that has a Critical Heigh Value M et least the height of the Highest Acpeael0le PeNFell HelgMottheadjecenleguipmanl (ftef. RSTM Ff48].) 14592500 DETAIL DECK HANGER CLAMP Post Ded (3) 5" HalfStainless Clamps Steel Stud (3)t/' x °/° X Drive Rivets� (6) °%' Tee / ( Flat \ Washer w/ (6) W, x 1 1/e' Hex Patch Nuts BHCS w/Pin (3)Deck Hanger Clamps 122197 90° Trianaular Tenderdeck e 2004 by Landscape Stredures All rights reserved Document #14582500 O �n I n C-)--) a, r M 42" 3 1070x D cn ut 122197 90° Trianaular Tenderdeck e 2004 by Landscape Stredures All rights reserved Document #14582500 U& landscape structures, J \SPEM145\145e2500 P65 Parts List PlayBooster-O 122197 90' Triangular Tenderdeck Part# Description Qty. 145658-00 90" Tri -Deck, Specify Color ..................................... 1 105327-01 5" Half Clamp, Specify Color .................................. 3 106022-00 Deck Hanger Clamp, Specify Color ........................ 3 120203-00 Triangular Deck Hardware Package ................... 1 100198-00 3/." x I '/." BHCS w/Pin, SST .................................. 6 100321-00 3/." Hex Patch Nut, SST ............................................ 3 100351-00 3/." Tee Nut, SST ........................................................ 6 100362-00 3/." Flat Washer, SST. ................................................ 3 100610-00 1/4" x 3/8" Drive Rivet, AL/SST................................. 3 Specifications Triangular Deck: Flange formed from 12 GA (.105") sheet steel con- fomting to ASTM A101 L Standing surface is perfo- rated with 3/16' diameter holes. Deck face has (4) slot- ted holes for face mounting components. The finished size measures 2 3/e" x 37 3/,'. Finish: Tendelfufl 3, color specified. Deck Hanger Clamp Assembly: Cast aluminum. Finish: PmShielde, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)paASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx.%manhour Weight: 67 lbs. Installation Instructions I) Mark posts for the appropriate height of the deck you are installing. 2) Fasten deck hanger clamps to marked position on posts. See Detail on front of sheet. 3) Lift deck assembly into position, lining up stud underneath deck with deck hanger clamp as shown. Attach using 3/." hex patch nuts with Y." Flat washers. With deck level and posts plumb, final tighten all hard- ware. 4) Install'/4"x3/."drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 5) After attachment of enclosures and components is complete, pour concrete footings. Allow concrete footings to cure a minimum of 72 hours before users are allowed to play on the structure. 6) Install protective surfacing before users are allowed to play on the structure. Eco 02268 Oxumeni p1a5.2500 repbm pll9)J4m. aeplxcd 90' Tri-Drc.. 63 M o CD ru 9/& landscape structures* Typical PlayBooster h Post i I 7 48" Deck , , , (2)'/e x'/�" BHCS w/Pin w/'/;' SAE Flat Washers /, (4)'/," x 1 '/;' BHCS w/Pin w/'/," SAE Flat Washers "--;-a Infill l gels � 24'I: a e 4 I I I li l rte/ I (2)3 2)3/ Flange == = / Nuts w/Pin Standard (4) '/;x1,/,' (4)w/Pin Hex Nuts Fll SAE BHCS Flatt w/'/;' SAE Washers ; Flat Washers SAF NOTE - Choose a pal Heng sValue o material Net �/� /�/� hes a Critical Height Value of at least iha ISO 14001 , He gMoheight lNe atlthe e a leg p xlghest liRe SW I I Certified I F1481, 20402400 Plange Nuts w/Pin DETAIL PANELATTACHMENT (2) Infill Post Typical ei Offset etrya CaP x 3'/;' w/Pin Handrails DETAIL HANDRAIL ATTACHMENT (3) Rails Step Section (6)'/," x 2" BHCS w/'/e' SAE Flat Washers 6 '/e. Low Crown 3 -Step Cap Nuts Section _ _ _ _--_- - -_ w/'/," Fender _ _ Washers Washers - + Lower Rail - _--_=,_:_tiYiensff 1 -Step Section o Deck w(�" 3 Flat Support cVIters NOTE: Protective surfacing adjacent to the transfer deck must be accessible. +' (4)'/, u1v Crown - Cap Nuts w/'/, SAE T o - (8)'/;' x 1'/;' (8) ,/;' Standard Flat Washers r o V ' BHCS w/Pin Hex Nuts w/'/;' `w/'/," SAE SAE Flat Washers Protective Flat Washers Surfacing PlayBoosters 152911 Transfer Module, 48", w/Handrails Sheet 1 of 2 0 2014 by Landscape Stmctures. All rights reserved Document #20402400 1h landscape structures, Parts List Part# 100610-00 105327-01 113468-00 113729-00 181371-00 181373-00 181374-00 181376-00 144696-00 144700-00 152640-00 152641-00 153398-00 153399-00 204034-00 100173-00 100196-00 100198-00 100327-00 100351-00 100353-00 100365-00 113027-00 124460-00 100378-00 100349-00 PlayBoosterl 152911 Transfer Module, 48", w/Handrails QfY• Color. Color Transfer Module Hardware Package ................... 2" BHCS. SST .................................................. x'/." BHCS w/Pin, SST ..................................... Y. x 1 '/a" BHCS w/Pin, SST ................................. 3/." Standard Hex Nut, SST ..................................... '1." Tee Nut, SST ........................................................ "/a" Flange Nut w/Pin, SST ....................................... %" SAE Flat Washer, SST ......._ __ ........................... %. x I Y." BHCS w/Pin, SST .................................. 3/." x 3 1/." BHCS w/Pin, SST .................................. '/," Fender Washer, SST ............................................ 3/," Low Crown Cap Nut, SST ................................. 111393-00 4 -Hole ISM) Hardware Package 100263-00/," x 2 /4" Expansion Anchors... 100327-00 '/." Standard Hex Nut, SST .......... 100365-00 34" SAE Flat Washers, SST .......... 121256-00 2 -Hole Hardware Package 100263-00 ISM) 3/." x 2 /," Expansion Anchors .... 100327-00 `/." Standard Ilex Nut, SST .......... 100365-00 7." SAE Flat Washers, SST .......... DB - Direct Bury SM - Surface Mount Specifications 2 2 2 2 1 1 Deck: Flange formed from 12 GA (.105") sheet steel con- fomung to ASTM A1011. Standing surface isp, c- Concrete Req.: rated with 1/16" diameter holes and measures 2 per Weight: (2) sides. Finish: TenderTuflr , color specified. Railings: Weldment comprised of formed 1 '/," O.D. x l l GA Fall Height: (. 120') steel tubing with 203 or 303 stainless steel in- serts with 3/j" internal threads. Finish: TenderTuff, cola specified. Step Sections: Formed from 12 GA (.105") shat steel conforming to ASTM A 1011. Standing surface is 24 3/." wide x 14" deep and is perforated with'/,." diameter holes. Fin- ish: TenderTuff. color specified. Spacer Tube: Made from 6061-T6 aluminum'/." OD. x 1 "/u. Fin- ish: ProShield', color specified. Panel: Solid color Permalene" panel, color specified. Deck Support: Weldment comprised of3'/1" O.D. RS20 (.125") ggal- vanized steel tubing and'/," O.D. x 5" long rod. Fin- ish: ProShield, color specified. Step Support: Weldment comprised of 1.660 O.D. RS20 (.080"-.095) 3/," 17," HR Finish: ProShiel and 1 x 1 x'/s' angle. color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned 'arnperproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: SM - Approx. 3 man hours DB - Approx. 4 man hours Concrete Req.: Approx. 3.4 cu. ft Weight: SM - 264 lbs. DB - 279 lbs. Fall Height: Deck Height Installation Instructions 1) (Direct Bury) Dig footings as shown. Refer to your Plan View/Foot- ing Layout. 2) Attach the deck support to the transfer deck wing 'Is" x'Is" BHCS w/pin and'/ " low crown cap nuts with 1/." SAE flat washers. NOTE: Make sure 1/s" rod on support is under support strap on deck m shown. Refer to the Deck Support Attachment Detail. 3) Attach the 3 -step section to the transfer deck win I/ x I'/a" BHCS w/pin with'/." SAE flat washers and'/." standard hex nuts with'/." SAE flat washers. 4) Attach the 3 -step section to the face of the mainstructure deck using 3/f x 1'/," BHCS w/pin with Y." SAE flat washers and 3/," standard hex nuts with 1/." SAE flat washers. 5) Attach the step support to the I step section using'/s" x 1 '/s" BHCS w/pin with'/," SAE flat washers and /s" standard hex nuts with 'Is" SAE flat washers. Refer to the Step Support Attachment Detail. 6) Attach the I -step section to the transfer deck using Y." x 1 '/," BHCS w/pin with'/," SAE flat washers and'/," standard hex nuts with SAE flat washers. 7) Attach offset hanger clamps to posts at heights shown using 5" half clamps,'/." x 1 '/s" BHCS w/pin and 1/," tee nuts. Refer to the Typi- cal Offset Hanger Clamp Spec Sheet. 8) Attach infill panels to the face of the mainstmcture deck using'/," x'/," BHCS w/pin with 3/,' SAE flat washers and'/," flange nuts w/pin. 9) Attach infill panels to offset banger clamp assemblies using 3/," x 3 Y." BHCS, spacer tubes and 3/." Flange nuts w/pin. See Panel Attach- ment Detail. 10) Attach the handrails to the 3 -step section using I/," x 2" BHCS with %,. SAE flat washers and '/," low crown cap nuts with'/," fender washers. Refer to the Handrail Attachment Detail. I I) Attach the handrails to the infill panels using 34" x 1'/," BHCS w/pin and'/," SAE flat washers. 12) Attach the lower mil to the transfer deck using Y." x 1 3/s" BHCS w/pia with'/," SAE flat washers and Vs" low crown cap nuts with Ya" SAE flat washers. 13) Attach the lower mil to the I -step section using$' x 2" BHCS with 3/." SAE flat washers and '/," low crown cap Vs with' /s' fender washers. Refer to the Handrail Attac Del, t��-2' 14) (Direct Bury)With transferdeck and veaQd supports lumb, pour concrete footings. Allow con mgs o cure imum of 72 hours before users are allowed a on&F stru ure. (Surface Mount) Mark holes for expapptprranchors on c�1@t�le slab through support plates. Detach the trio gla fro�'jhe m n t crate and slide module aside, drill'/," x)*—d€d� hoft on rtPmq usingg hammer drill and Y." masonry bit. on ®dale drilled holes and tap expansion anchors intd�illed hol0s. Fasten support plates to expansion anchors using /i standar"ex nuts with SAE flat washers. Reattach module to stmcture.N 15) Install'/," x'/." drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 16) Install protective surfacing before users are allowed to play on the structure. E n100178 D"cun"n,2a4024Wrtv� I M 1379 .Replaced haN =p ka,e. landscape structures• PLAN VIEW FOOTING LAYOUT RIGHT HAND STEP AR', ncek 1 -Step PLAN VIEW FOOTING LAYOUT IrEFT HAND STEP 1 -Step I .o„ fl—, DETAIL 11 200 "1 Rock SURFACE MOUNT DECK SUPPORT DETAIL (4) b/e' Standard Deck Support " Hex Nuts w/ ! / SAE FlatI,..�. (2) b/;' Standard Washers Hex Nuts w/ 3/4" Deck Support SAE Flat (4)'/"x23/ -- -------- a 4 Washers Expansion 12 bl;' x 2 d/;' Anchors - Expansion Concrete Anchors NOTE: Sufficient Crushed tive surfacing must protec- cover Rock hardware to satisfy height requirements. fall SAFETY NOTE r- 204023a DETAIL STEP SUPPORT BURY Loose Fill Protective Ste Surfacing p Support -.; K Subgrad Concrete .` 8" -- --- 11 200 "1 Rock DETAIL SURFACE MOUNT DETAIL STEP SUPPORT DECK SUPPORT BURY ,-Step Section Deck Support Step Support Loose FIII Protective:: / Surfacing DECK SUPPORT ATTACHMENT a�Concrete Concrete Crushed Crushed Rock 14" Rock 380 (2) b/;' Low Crown DETAIL.— Cap Nuts w/ b/e' SAE Flat Washers STEPSUPPCn_jT ATTifiCHT Deix ---------- - - - n - — -- ,-step SEaloh rn r (2) a/;' x'/." NOTE: Make sure'/d" rod on BHCSw/Pin support is under support .a strap on deck as shown. (4) Standard Hex Nuts hep (4) a/;' x 1'/;' BHCS Deck Pin w/ b/;' SAE Support w/pin w/'/;' SAE Flat Support Flat Washers Washes oster® 152911 Transfer Module. 48". W/Handrails Sheet 2 of 2 02014 Hy LaMsfa Sa &ums. All rghls mserve V _ landscape structures (2) Typical Offs Hanger Clamp Assemblies Top o'" Clamp Top SAFETY NOTE Choose a prMecMe surtatlng material that has a Critical Height Value of et least the height of the Highest Accasside Pa"all '® Cerlil'letl FH'e4g8idlMa§acenl equprrwit lRet.ASTM 13533200 DETAIL 90o ATTACHMENT BRACKETS (2) a/;' Flange Nuts w/Pin Post ------� Pipe (2) a/e � x 1 1/2 Wheel BHCS w/Pin Se Tee nderdeck 2 a/' Detail S7 DETAIL WHEEL ASSEMBLY a/,a" x 1" Spring Pin Cap (2) a/;' x T/;' BHCS w/Pin 4;��Wheel Brackets — Pipe Barrier (2) a/a " x 1 ,/z Carriage Bolts (2) a/;' Flal Nuts w/Pin NOTE: Steering Wheel Infill Panel available. Re- fer to the Wheel Spec Sheet. Protective „ "Surfacing )sten"' 116244 Wheel Clamp Refer to Wheel Assembly Details on the back of sheet 2. DETAIL TENDERDECKS Pipe (2) a/;' Standard w//a^ SAE Flat Hex Nuts w/ a/a" Washers SAE Flat Washers N O crs O 4 -11 C-) �, r ::4c-) :-ri: rr-,, rn a � Zz cn cn DECK MOUNT Barrier. w/Wheel 02W4 by LanOscape Structures. All rights reserved Document#14865100 loop � 115PECS\146\1486510n.P65 Parts List PlayBooster-' 116244 Pipe Barrier, w/wheel NNheel Bracket: Weldment comprised offonned3/1.'plate and%"O.D. stainless steel shaft. Finish: ProShield, color specified. Part# Description Qty. ABOVE DECK 132755-00 Pipe Barrier, Specify Color ....................................... 1 128824-00 90" Attachment Bracket, Specify Color .................. 2 127207-00 Wheel Clamp, Specify Color .................................... 1 127242-00 Steering Wheel Bmcket, Specify Color ................... 1 108432-00 Wheel, Specify Color ................................................. 1 105327-01 5" Half Clamp, Specify Color .................................. 2 113729-00 Offset Hanger Clamp, Specify Color ....................... 2 100610-00 1/," x'/," Drive Rivet, AL/SST................................. 2 132739-00 Barrier, Above Deck Hardware Package ............ 1 100198-00 3/," x 1 1/," BHCS w/Pin, SST .................................. 6 100201-00 5/," x 1 1/g' BHCS w/Pin, SST .................................. 2 100351-00 %" Tee Nut, SST ........................................................ 4 100353.00 3/," Flange Nut w/Pin, SST ....................................... 2 116017-00 3/," x I '/r" Carriage Bolt w/Patch, SST .................. 2 100327-00 3/s" Standard Hex Nut, SST ...................................... 2 100365-00 3/," SAE Flat Washer, SST ................. I...................... 4 148618-00 Wire/Pipe Barrier Hardware Package ................ 1 100196-00 3/a" x 7/," BHCS w/Pin, SST ..................................... 2 100353-00 '/a" BHCS w/Pin, SST ............................................... 2 118452-00 3/,6" x I" Spring Pin, SST ......................................... 1 148623-00 Cap, White.................................................................. 1 BELOW DECK 132755-00 Pipe Barrier, Specify Color ....................................... 1 128824-00 90" Attachment Bracket, Specify Color .................. 2 127207-00 Wheel Clamp, Specify Color .................................... 1 127242-00 Steering Wheel Bracket, Specify Color ................... 1 108432-00 Wheel, Specify Color ................................................. 1 105327-01 5" Half Clamp, Specify Color..................................4 113729-00 Offset Hanger Clamp, Specify Color ....................... 4 113464-00 Angled Panel Bracket, Specify Color ...................... 1 100610-00 1/4" x 5/," Drive Rivet, AL/SST................................. 4 148628-00 Wire/Pipe Barrier Hardware Package ................ 1 100196-00 3/a" x 7/," BHCS w/Pin, SST ..................................... 2 100353-00 '/," Flange Nut w/Pin, SST ....................................... 2 118452-00 3/,4" x 1" Spring Pin, SST ......................................... 1 148623-00 Cap, White.................................................................. 1 132741-00 Barrier, Below Dark Hardware Package ............ 1 116017-00 1/," x 1 '/," Carriage Bolt, SST ................................. 2 100198-00 3/," x 1 1/," BHCS w/Pin, SST .................................. 8 100196-00 3/," x 7/," BHCS w/Pin, SST ..................................... 2 100203-00 5/," x 2 1/4" BHCS w/Pin, SST .................................. 2 100351-00 Y." Tee Nut, SST ........................................................ 8 100201-00 5/," x 1 1/2" BHCS w/Pin, SST .................................. 2 100327-00 3/," Standard Hex Nut, SST ...................................... 2 100365-00 '/." SAE Flat Washer, SST ........................................ 4 100353-00 '/," Flange Nut w/Pin, SST ....................................... 2 Specifications Barrier: Weldment comprised of%" solid steel vertical mils, I Vg' O.D. x 11 GA (.120") steel horizontal mils with 203 m 303 stainless steel welded inserts with 5/," internal threads, I'/," x 1 1/2" x 29 3/g' angle iron. Barrier mea- sures 33 7/," wide x 39 "/Ig' high. Finish: Tendelruft l, color specified. 90" Bracket: Formed from 1/g' x 11/4" HRPO flat steel. Finish: ProShield®, color specified Wheel: 12" diameter cast A356 aluminum alloy. Finish: TenderTuff, color specified Angled Panel Brkt.: Weldment comprised of .190" thick 5052 aluminum formed angle with (2) 6061-T6 aluminum threaded tubes 1 1/," O.D. x I '/2" long. Finish: ProShield, color specified Wheel Clamp: Formed from x 2" HRPO zinc -plated. Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications) Installation Time: Approx. 1 1/4 man hour Weight: Above Deck 58 lbs. Below Deck 62 lbs. Installation Instructions ABOVE DECK (See Sheet I of 2) I ) Attach pipe barrier to the face of the deck using 3/g' x 1 1/s" BHCS w/pin with 3/," SAE flat washers and'/.' standard hex nuts with 3/g' SAE flat washers. Refer To The Tenderdeck Detail.. 2) Attach offset hangerciamps to posts at height shown, using 5"half clamps and'/," x I 1/s" BHCS w/pin with'/," tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 3) Attach the 90' attachment brackets to pipe barrier using 5/," x 1 1/2" BHCS w/pin. Refer To The 90" Attachment Bracket Detail. 4) Attach the 90" attachment brackets to the offset hanger clamps using 3/," x 1 1/," carriage bolts and %" flange nuts w/pin. Refer To The 90" Attach- ment Bracket Detail. 5) Attach wheel bracket and wheel clamp to barrier in desired position us- ing 3/," x 7/e" BHCS w/pin and'/," flange nuts w/pin. Slide wheel and cap onto wheel bracket shaft and tap 3/16" x V spring pin through cap and shaft. Refer To The Wheel Assembly Details on front of sheet I and the back of sheet 2. 6) Install protective surfacing before users are allowed to play on the struc- ture. BELOW DECK (See Sheet 2 of 2) 1) Attach offset hanger assemblies to posts at height shown, using 5" half clamps and 3/8" x 1 1/," BHCS w/pin with 3/g' tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 2) Attach angled panel bracket to bottom of pipe barrier ming 3/,"x7/,"BHCS w/pin with %" SAE flat washers and'/," standard hex nuts with '18" SAE flat washers. See Below Deck Mount. 3) Attach angled panel bracket with pipe barrier mAgset hanger clamp assemblies using 54" x 2'/4" BHCS w/pin. See Belt Deck Mount. 4) Attach the 90" attachment brackets to pi r use 5/g' x FAiaeBHCS w/pin. Refer To The 90o Attachment B --4 etas NAM 5) Attach the 90" attachment brackets to thepr'se0anget clampsle ft 54" x 1 1/2" carriage bolts and'/," flange nuts a #4r) tefe90 The§0° Attach- ment Bracket Detail. -<.m a, rn 6) Attach wheel bracket and wheel clamp ta'eer illsiredr n us- ing'/." x 7/," BHCS w/pin and'/," flanj�A w/fR. Slide. 71el and cap onto wheel bracket shaft and tap'/,;5'1r I" spft pin through cap and shaft. Refer To The Wheel Assembly Details orrflbnt of sheet 1 and the back of sheet 2. 7) Install 1/4" x'/," drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec sheet. 8) Install protective surfacing before users are allowed to play on the struc- ture. Eco x525080. Uu tX148651W, 1 #135332W. Rtp1a,'N 4 "v, spin, pin. 9& landscape structures 135332a0 Typical PlayBooster Post ' 48" or Higher -- ---r-' Deck --------------------- I (2)3/," Flange ��� Refer to Wheel Assembly Nuts w/Pin Details on the back of sheet 2. (4)TypicalOffset Hanger Clamp Pipe Barrier To of Clam Assemblies (2)90- Attachment 2)90°Attachment Wheel Brackets i ' (2)11 x 1 112" � BHCS w/Pin (2)3/e"X11/2" i a Carriage Bolts (2)'/e x 2 1/4' BHCS w/Pin (2) % Standard 1 Hex Nuts w/ a/;' ' SAE Flat Washers 20 of Clam _ O Firild Gsde C� ti 1 Protective Surfacing Angled Panel (2) 3/e, X I/e � (� M Bracket �BHCSw/Pin ern A w/'/e" SAE Fill ? S r Washers n BLOW D CK MOUNT PlavBooster'' 116244 Pipe Barrier, W/Wheel Sheet 2 of 2 02004 by Lanascape Structures All rights reserved Document #14865100 j & landscape structuresA '/,a' x t Spring C DETAIL NOTE: To assist in the alignment of the cap to the wheel bracket shaft, tap spring pin through cap approximately V,s'. Orient spring pin to groove on wheel bracket shaft. Slide cap in place and tap spring pin though cap and shaft until flush. 116244 Pi ©2004 by Landscape SimcWres All ngnis reserved 3/,e' x Sprint Cap (CAP BACK VIEW) Barrier, wMheel 1 0 4 )> 0 cr, r �m = m _r oX D o S & landscape structures` (2) Typical Offset Hanger Clamp \Assemblies 1 11 CERTIFIED DETAIL 90o ATTACHMENT BRACKETS (2) a/e" Flange .-- Nuts w/Pin i — — (2) 90° Attachment Brackets 0 ®' Pipe Barrier CO- 2 ) s/a" x 1 +/q. Carriage Bob , See�rdeck 2 11 Detail 87 SAFETY NOTE R oose a prolective sunadng matenal mal sticalHeightVelue of at leas) NeHighestP.F•egfTM F1CST.) 13533100 Pipe Barner DETAIL x 1 +/i' TENDERDECKSPipew/Pin , I , l l + i l I Protective -r' --Surfacing PIayBOOSter'=116244 Pi 02001 by Landscape Structures All nghls reserved l l l l l l l l l l l l l l l 1 I l l l l l l l l l l l l l l l l I l , l l Barrier (2) a/e" Standard (2) a/e' X 1 '/;" Hex Nuts w/ a/;' BHCS w/Pin SAE Flat Washers w/ 3/;' SAE Flat Washers N O o A ti M+ tJ1 O rr a � a 0 r DECK MOUNT Sheet 1 of 2 Document#13533100 Ilk landscape structures" Parts List Part# Description Qty - ty.ABOVEDECK 3/," x I '/," BHCS w/Ptn, SST.......................................6 ABOVE DECK 5/e" x 1 '/3" BHCS w/Pin, SST.......................................2 132755-00 Pipe Bartier, Specify Color .... ................... ..................1 100353-00 128824-00 90° Attachment Bracket, Specify Color ... ...... ._........... 2 105327-01 5" Half Clamp, Specify Color ..... ._............ .. .........2 113729-00 Offset Hanger Clamp, Specify Color ............................ 2 100610-00 '/," x 5/," Drive Rivet, AUSST._._ ..... 132739-00 Barrier, Above Deck Hardware Package .................1 100198-00 3/," x I '/," BHCS w/Ptn, SST.......................................6 100201-00 5/e" x 1 '/3" BHCS w/Pin, SST.......................................2 100351-00 34" Tee Nut, SST..... ........... .._._..._._............................. 4 100353-00 3/: Flange Nut w/Pin, SST. .................... — .................... 2 116017-00 3/," x 1 I/3" Carriage Bolt w/Pateh, SST.........................2 100327-00 3/," Standard Hex Nut, SST...........................................2 100365-00 34" SAE Flat Washer, SST.............................................4 N BELOW DECK 132755-00 Pipe Barrier, Specify Color...........................................1 128824-00 90 -Attachment Bracket, Specify Color.........................2 105327-01 5" Half Clamp, Specify Color...... ................................. 4 113729-00 Offset Hanger Clamp, Specify Color ............................4 113464-00 Angled Panel Bracket. Specify Cokx............................1 100610-00 '/," x 5/," Drive Rivet, ALSST......................................4 132741-00 Barrier, Below Deck Hardware Package .................1 116017-00 3/," x 1 '/i" Carriage Bolt, SST..... ................................. 2 100198-00 3/. x I Y. BHCS w/Pin, SST........ ............................... 9 100196-00 % x 5/: BHCS w/Pin, SST..........................................2 100203-00 5/: x2'1: BHCS w/Pin,SST.......................................2 100351-00 3/: Tee Nut SST..... ........... .--...................................... 8 100201-00 5/," x I'/i BHCS w/Pin, SST ..................................... 2 100327-00 3/, Standard Hex Nut, SST... ........................................ 2 100365-00 3/," SAE Flat Washer, SST.............................................4 100353-00 Y.' Flange Nut w/Pin, SST.. ..... .................................. -2 Specifications Barrier: Weldmentcomprisedof3/," solid steel vertical rails,) I/," O.D. x I I GA (.120") steel horizontal rails with 203 or 303 stainless steel welded inserts with %" internal threads. I I/," x 1 I/r" x 29'/r" angle iron. Barrier measures 33'/," wide x 39131,6" high. Finish: TenderTuff ', color specified. 90" Bracket: Formed from '/," x I V," HRPO flat steel. Finish: ProShield', color specified. Angled Panel Brkt.: Weldment comprised of.190" thick 5052 aluminum formed angle with (2) 6061-T6 aluminum threaded tubes I I/a" O.D. x I I/3" long. Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tam- perproof in design. stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product instal lation/specifications) Installation Time: Approx. I man hour Weight: Above Deck 52 lbs. Below Deck 56 lbs. PlayBooster" 116244 Pipe Barrier Installation Instructions ABOVE DECK (See Sheet 1 of 2) 1) Attach pipe barrier to the face of the deck using 3/," z 1 I/," BHCS w/pin with 3/," SAE flat washers and 3/a' standard hex nuts with 3/.' SAE flat washers. Refer To The Tenderdeck Detail.. 2) Attach offset hanger clamps to posts at height shown, using 5" halfclamps and %"x 1 '/p' BHCS w/pin with'/," tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. 3) Attach the 90' attachment brackets to pipe barrier acing 5/," x I '/r" BHCS w/pin. Refer To The 901 Attachment Bracket Detail. 4) Attach the 90' attachment brackets to the offset hanger clamps using 5/." x I '/,"carriage bolts and 3/,"flange nuts w/pin. Refer To The 90' Attachment Bracket Detail. 5) Install protective surfacing before users are allowed to play on the structure. BELOW' DECK (See Sheet 2 of 2) I Attach offset hunger assemblies to posts at height shown. Using 5" half clamps and 3/," x 1 '/w' BHCS w/pin and with 3/1" tee nuts. Refer To The Typical Offset Hanger Clamp Spec Sheet. I Attach angled panel bracket to bottom of pipe barrier using'/," x'/," BHCS w/pin with 3/e SAE flat washers and'/: standard hex nuts with 3/," SAE flat washers. See Below Deck Mount. Attach angled panel bracket with pipe barrier to offset hanger clamp assemblies using'/," x 2 Y," BHCS w/pin. See Below Deck Mount. Attach the 90' attachment brackets to pipe barrier using 5/," x I I/3" BHCS w/pin. Refer To The 90" Attachment Bracket Detail. Attach the 90" attachment brackets to the offset hanger clamps using 3/." x I '/,.carriage bolts and 3/," flange nuts w/pin. Refer To The 90' Attachment Bracket Detail. Install It," x 5/," drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec sheet. Install protective surfacing before users are allowed to play on the structure. N O C:) t) -C 1 r �irn A I , 1 Y o N 3"1 th ,MI35331aprep]r 01316C60a. Rmg lbvnam bnaWa. k& ,I `/ 131646a0 landscape structures® , , Typical PlayBooster Post i 46" or Higher -r ' Deck ------- -------- I " (2)% Flange �` � �-------- Nuts w/Pin ' (4)TypicalOffset Hanger Clamp Pipe Baffler Ta of Ctem Assemblies (2) 9l Attachment Brackets t (2)'/a' x 1 '/z' BHCS w/Pin ` (2)'/s' x 1 Vi' Carriage Bolts , t (2) 1/0• x 2'/4• (2) a/e' Standard BHCS w/Pin Hex Nuts w/ /;' SAE Flat Washers 0. Top Of CWM b. � de_, Gra Finished _ Protective Surfacing Angled Panel Bracket 116244 Pipe Barrier C —i7 C-') •I I r BELO DECK WONT Sheet 2 of 2 0 2001 by Landscape Strictures An rights reserved Document #135331 -<r— (2) %" x'/e" "' BHCS w/Pin w/ 14" SAE Flat Washers 116244 Pipe Barrier C —i7 C-') •I I r BELO DECK WONT Sheet 2 of 2 0 2001 by Landscape Strictures An rights reserved Document #135331 U landscape structures, Typical PlayBooster Post ro d Pene1- i WE SAFETY NOTE Choose a l r j Heiv h sVala o al le al Ihal has a Cf the Heigh V ixe of a, leas) Ne IS014001 aline ao negAw eM l(Re a ASM Ce ll'letl F1061.) 13037400 (2)'/a" Flange Nuts w/Pin i , I Periscope Panel , DECK MOUNT All hghts reserve) 117957 DETAIL PANELATTACHMENT I (2) Typical Offset Hanger Clamp (2) Spacer Tubes Periscope Panel _ (2)'/a" x 3 3/4" BHCS w/Pin DETAIL TENDERDECKS Perlacope Panel (4)1/a' Flange Nuts w/Pin (4)'/e" x'/e' BHCS w/Pin w/'/;;SAE Flat Washers r cn CD _ C??' all G? 1.0 i✓ UI Qn Panel Sheet I of 2 888438-6574LS101rect 763-972-52001n1. FAx(763(972-3185 �a ••tl U V l/ C. landscape structures NOTE: The minimum height deck above a Ground Level Periscope Panel is 64". Typical PlayBooster� Post ' i I I (2)'/a' Flange Nuts w/Pin T, of Ctam�A (4)Typical Offset Hanger Clamp Assemblies M-) �71J (2) Spwar I ' Tubes57- Q I , O O I I (2)'4,x33/„ � I BHCS w/Pin O O (2),/," x 2 1/4" BHCS w/Pin Q OQi w/Pln ro ' o ' O To of Gan' I o Oil Grey°; _ - 0. s Protective Surfacing Angled Panel \�(4)'/�" Flange Bracket NW w/Pin PlayBoosterfi" 117957 Periscope Panel C 2004 by LarW.r Slrudures All ngnts reserved bb IoW ivioun 13037490 rn 9/1, landscape structures` (7) ,/s, Nuts w (Z)' BH( BACK OF PANEL 1303700 cope Assembly x 1 V", w/Pin a/s. x 7/e. CS w/Pin P12 olosler" 117957 Periscoee Panel Sheet 2 of 601 4 H STREET SOUTH, DELANO, MINNESOTA 5532&8605 868.5744878 LSI 1"812111 Help 6884138.6574 LSI MOM 763.972.5200 Int. FAX (763)972-3185 Document #1485690MI Uvk landscape structures" Parts List Part# Description Qty. A rns ABOVE DECK O 129071 Periscope Panel, Specify Color ................................ 1 129118 Periscope Assembly, Specify Color ......................... 1 130269 Mounting Plate, Sped Cotor................................. 1 113729 Offset Hanger Clamp, Specify Color ....................... 2 105327 5" Half Clamp, SpeciFy Color .................................. 2 113468 Spacer Tube, Specify Color ................................._... 2 100610 b." x 14" Drive Rivet, AUSST................................. 2 130367 Perlscate Attachment Hardware Package ......... 1 100195 '/," x Y. BHCS w/Pia, SST ..................................... 2 100196 % x 7/," BHCS w/Pin, SST ..................................... 2 100198 1/." x 1 '/," BHCS w/Pin, SST .................................. 3 100353 Y." Flange Nut w/Pin, SST ....................................... 7 100362 3/a" Flat Washer, SST ................................................. 1 145121 Urethane Bumper ....................................................... 1 124900 Tenderdeck Mounting Hardware Package......... 1 124460 1/," x 3 '/," BHCS w/Pin, SST .................................. 2 100196 1/," x'/," BHCS w/Pin, SST ..................................... 4 100198 %" x I '/." BHCS w/Pin, SST .................................. 4 100351 1/," Tee Nut. SST ........................................................ 4 100353 5/," Flange Nut w/Pin, SST ....................................... 6 100365 1/," SAE Flat Washer, SST ........................................ 4 BELOW DECK 129071 Periscope Panel, Specify Color ................................ 1 129118 Periscope Assembly, Specify Color ......................... 1 130269 113729 Mounting Plate, Specify Color ................................. Offset Hanger Clamp, Specify Color ....................... 1 4 105327 5" Half Clamp, Specify Color .................................. Vier 4 113468 Spacer Tube, Specify ...................................... 2 113464 Angled Panel Bracket, Specify Color ...................... 1 100610 '/," x'/," Drive Rivet, AUSS ............................... 4 130367 Periscote Attachment Hardware Package ......... 1 100195 1/8" x 5/. BHCS w/Pin, SST ..................................... 2 100196 1/." x 7/i BHCS w/Pin, SST ..................................... 2 100198 Y." x 1 1/," BHCS w/Pin, SST .................................. 3 100353 % Flange Nut w/Pin, SST ....................................... 7 100362 '/," Flat Washer, SST ................................................. 1 145121 Urethane Bumpper....................................................... 1 124947 Below Deck Mountin` Hardware Package......... 1 124460 '/a" x 3 1/." BHCS w/Pm, SST .................................. 2 100195 1/." x'/," BHCS w/Pin, SST ..................................... 4 100198 1/, x 1 '/," BHCS w/Pin, SST .................................. S 100203 5/," x 2 1/," BHCS w/Pin, SST .................................. 2 100351 3/." Tee Nut, SST ........................................................ 8 100353 '/," Flange Nut w/Pin, SST ..................................... 6 Soecifications PlayBooster" 117957 Periscope Panel Permalene° Panel: Two color panel measures 35 '/s" x 41" high, color specified. Periscope Assy.: Fabricated from an octagon 14 GA (.075") steel tube with (2) 18 GA (.048") 304 stainless steel bright an- nealed (reflective finishes). Periscopge rotates vertically and horizontally. Finish: PmShield4, color specifed. Permalene: Hand -grip and tense covers are black in color. Mounting Plate: Fabricated from formed I I GA (.120") HRS. Finish: ProShield, color specified Angled Panel Britt.: Weldment comprised of.] 90" thick 5052 aluminum formed anile with S2) 6061-T6 aluminum threaded tubes 1 1/s O.D. x I /," long. Finish: ProShield, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/," O.D. x 1 Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof m design, stainless steel (SST) WASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Above Deck Approx.'/, man hour Below Deck Apppprox. 1 man hour Weight Above Deck Mbro,. Below Deck 73 lbs. Installation Instructions ABOVE DECK I ) Attach panel to the face of the deck using'/." x 7/," BHCS w/pin with 1/." SAE flat washers and'/." flange nuts w/pin. Refer to the Tenderdeck Detail. 2) Attach offset hanger clamp assemblies to Posts at height shown, us- ing half clamps and'/." x I Y." BHCS w/pm with 3/." tee nuts. Refer to the Typical Offset Hanger Clamp Spec Sheet. 3) Attach panel to the offset hanger clamp assemblies, using 3/s" x 31/," BHCS w/pin, spacer tubes and'/." flange nuts w/pin. Refer to the Panel Attachment Detail. 4) Attach periscope assembly to panel, using mounting plate,'/," x'/s" BHCS w/pin,'/." x 7/a' BHCS w/pin, %" x I'/s" BHCS w/pin and'/s' flange nuts w/pin, as shown. 5) Attach urethane bumper to periscope assembly, using 3/," x 11/a' /. BHCS w/pin with'" flat washer and 1/," flange nut w/pm, as shown. 6) Install protective surfacing before users are allowed to play on the structure. BELOW DECK 1) Attach offset hanger clamp assemblies to Posts at height shown, us- ing half clamps and 3/," x I I/." BHCS w/pm with'/." tee nuts. Refer to the Typical Offset Hanger Clamp Spec Sheet. 2) Attach angled panel bracket to bottom of panel, using 1/8" x 1/." BHCS w/pin and 3/." flange nuts w/pin. Refer to Below Deck Mount. 3) Attach angled panel bracket with panel to offset hanger clamp as- semblies, using 1/," x 2 IQ' BHCS w/pin. Refer to Below Deck Mount. 4) Attach top of panel to offset banter clamp assemblies, using 1/," x 3'/," BHCS w/pin, spacer tubes and /," flange nuts w/pin. Refer to Below Deck Mount. 5) Attach periscoppye assembly to panel, using mounting Dlate, 3/s" x 5/s" BHCS w/pin, 1/," x 7/e' BHCS w/pin,'/," x I Ys" BHCS w/pin and 3/a' flange nuts w/pin, as shown. 6) Attach urethane bumper to periscope assembly, using 3/." x I I/," BHCS w/pin with %" flat washer and'/," flange nut w/pm, as shown. 7) Install Y." x 1/," drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 8) Install protective surfacing before users are allowettig play on the structure. U Ci p "Pq D' 4 a 1 EC0#5218. Pwwrcn�pl<856900 rtplxe. M1109?700. RepI.xW ,uHl�ne.�„p u'iiM1 urtlh"ce bumlxr. r .<r rn A rns O= O n o N EC0#5218. Pwwrcn�pl<856900 rtplxe. M1109?700. RepI.xW ,uHl�ne.�„p u'iiM1 urtlh"ce bumlxr. k& landscape structures` s n (4) 1/ „ X t ,/e, Typical BHCb III PlayBooster Post \ (2) Rod Covers i o TAKETURNS TO MATCH THREE o IN A ROW To VAN I � I y t t 4 O t II ` It II uti II ` i III I ,u t I mil S i V I11 IIII \�`V 111 \J) � 11\ Protedilda Surfacing Match 3 1 11 CERTIFIED (4)'/e' Flange Nuts w/Pin I i I SAFETY NOTE Choose a protective surfacing matenat that has a Critical Height Value W at least he height of the Highest Accessiele Parl Fall Height of the adjacent equipment (Ref ASTM Fta67.) Access NOTE: The large radius ' on the access bracket $ shown. h t a t P � I' I, I �t-Ii ' td1 _--Irr i t ji m ; 111 U I I Ct/ I {ti _< <ril Accessible Surface` I93719191cil .:11 ' 1 01 7TH STREET SOUT ELANO, MINNESOTA 55328-860 88574-0678 LSI Install Hel 88-438-6574 LSI Direc 63-972-5200 In AX (763) 972-318 f to - ••111 k�l landscape structures Parts List PlayBooster° 135730 Match 3, Reach Panel Part= Description Qty. 135115 Match 3 Panel, Specify Color.. ... _.__ ................._.1 '/"" Tee Nut. SST ...-- .....................................................4 136774 Pivot Block SR ..................... 127463 135116 Aluminum Rod 121/x ..................................................4 414 x 3/," Torx Screw, SST............................................4 135114 Rod Cover, Specify Color ..................... ........... ............ 2 127331 Angle, Specify Color.. ................................................... 1 188387 Access Clamp, Specify Color........................................2 105327 5" Half Clamp, Specify Color.......................................2 100610 '/," x'/," Drive Rivet, AUSST......................................2 211890 Access Panel Spacer, Specify Color ..............................2 122034 Match 3 Hardware Package .. ...1 100198 3/r"xI'/e BHCS w/Pin, SST ........ ........ ...........__. _..... 6 100353 '/a" Flange Nut w/Pin, SST .................................. .._...... 6 212999 Panel Hardware Package..........................................1 100196 %"x Y, BHCS w/Pin, SST.. .......................................... 4 100351 '/"" Tee Nut. SST ...-- .....................................................4 100353 Flange Nut w/Pin, SST............................................4 127463 Tom Hex Bit.................................................................. l 127872 414 x 3/," Torx Screw, SST............................................4 100171 '/a x 1 '/, BHCS w/Pin, SST .............................. ......... 100365 '/,"SAE Flat Washer. SST................... ._...................... 8 Specifications Panel: Two color Pemalene* panel measures 34" wide x 14" high, color specified. Panel Spacer: Permalene*, color specified. Pivot Blocks: U.V. stabilized high-density polyethylene, tan on one side and brown on the other. Aluminum Rod: '/t" x 12'/g" aluminum rod. Rod Cover: Solid color Permalene, color specified. Angle: Fabricated from formed 11 GA (.120" HRS. Finish: ProShield', color specified. Access Clamp: Weldment comprised of/a' HRPO steel plate and I/," x I'/ "wide steel clamp. Finish: PmShield, color specified. Half Clamp: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fastenersshall besocketed and pinned tam- �m perproof in design, stainless steel (SST) per ASTM F rn 879 unless otherwise indicated (see specific product 3 instal lation/specifications). Installation Time: Approx. 3/, man hour Weight: 26 lbs. Installation Instructions 1) Attach the angle to the bottom of the panel, using # 14 x'/," torx screws. Refer to the Angle Attachment Detail. 2) Attach the access clamps to posts at the height shown, using 5" half clamps,'/r" x Y." BHCS w/pin with'/r" SAE flat washers and'/r" tee nuts. NOTE: The large radius on the access clamp needs tojace down, as shown. 3) Attach panel and access spacer panels to access clamps, using '/a" x I/r" BHCS w/pin, with '/." SAE flat washers and'/," flange nuts w/ pin. Refer to the Panel Attachment Detail. 4) Place (4) pivot blocks on each of the 12'/g" rods and tap rods into cut out grooves on panel using a plastic or rubber hammer. Continue this process until all (4) rods are in place. Refer to the Pivot Block Assembly Detail. 5) Attach the rod covers using'/r" x 1 I/c" BHCS w/pin and'/a" flange nuts w/pin. 6) Install I/, x V,"drive rivets in all 5" half clamps. Refer to the Typical Offset Hanger Clamp Spec Sheet. 7) Install protective surfacing before users are allowed to play on the structure. Eco M01061a9 D"cunml 821299000 repnca e1888a21n. Replaced hardware pkg d added spacer panels. o_ 0 cn O "'tea �m a rn 3 7C C:) O Eco M01061a9 D"cunml 821299000 repnca e1888a21n. Replaced hardware pkg d added spacer panels. J & landscape structures£ (4) a/ „ X t 1/� BHCb w/Pin ,At/ 31 " SAE Flat washers (2) Access Spacer Panels (2)Access Clamps SAFETY NOTE Ctmose a Protective surfacing materialNat hius a cnUcal Height Value of i least tM1e heght of the Highest Accessible PartlFall '� 001 Height of the adjacent equipment (Ret cuunee ASTM F1487 ) 212995b DETAIL PANEL ATTACHMENT (2) 5" Half NOTE: The large radius on the access clamp needs to face down, as shown. (4) Tee PlayBooster® Post Panel (4) a/ X 1/ BHCb w0in w/ e/ " SAE Flat Washers DETAIL PANEL ATTACHMENT (WITH BALCONY DECK) /fALft (4)'/a' Flange Nuts w1Pin ©2015 by Landscape Structures. All rights reserved ESOTA 66328.860 8.674-0678 LSI Install Hel - 88-438-6674 LSI Dirac r rn 0 let 63-972.6200 InAX (763( 972-318 ■r a • 111 st& landscape structures` Typical ` PlayBooster . D, ° Post 0 o �•_•� a n =I. Match 3 Panel Angle NOTE: If the Match 3 Reach Panel is located on a wheel- chair accessible deck, a curb (Model #128623) is required. IayBoostei4 C 2015 by Landscape Structures •All rights reserved 212990a DETAIL PIVOT BLOCK ASSEMBLY (16) Pivot Blocks 2) Access lamps DETAIL ANGLE ATTACHMENT Match 3 Panel 1 (4) #14 x e/�' Angle Torx Screws N O_ O U 0 :-<rb CTI M :. 0 �� o O 9& _ `-' landscape structuress (4) 3/," SF Flat Wasl (4) 3/a' x BHCS N OmniSpin Spinner OmniSpin Frame Assembly Loose FIII Protective ' Surfacing Subgrade LSO 14001 SAFETY NOTE Choose a prolective aurtaarp material that has a Critical Height Value oC et lent tha height of the Highest Accesside PaNFall 1leiplaaltle adjamtepiprnenf (Rat ASTM F115T.) 18384300 Y KAMC ANGM V KIND 7' 2.13 m 173591 ay Safe Surface rning urface (4)'/," Standard DETAIL Hex Nuts w/'/," o.m Flat WasFqrs �++ Bowl Sp w O FrameA'§a ly (4) i /ice Expaa N g An �D y Concrete cn fT in° Spinner Sheet 1 of 2 02012 by Larwscape SthicWras. All rights reserved. Document #18384300 W1 Kids in Motion 173591 OmniSpin' Spinner landscape structures` Parts List Installation Instructions Part# Description Qty. 171060-00 OmniSpin Spinner, Specify Color ........................... 1 171061-00 OmniSpin Spinner Frame Assy., Black ................... 1 183892-00 OmolSplu Spinner Hardware Package ............... 1 100196-00 3/." x'/." BRCS w/Pin, SST ..................................... 4 100365-00 3/." SAE Flat Washer, SST ........................................ 4 156846-00 Play Safe Label, 2-12 Years ...................................... 1 183064-00 Warning Label............................................................ 1 175599.00 4 Hole (SM) Hardware Package ........................... 1 100271-00 1/3" x 5 1/3" Expansion Anchor w/Nut/Washer ........ 4 SM - Surface Mount Specifications OmniSpin Spinner: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. OmniSpin Spinner Frame Assembly: (Frame) Weldment comprised of 2.375" O.D. RS20 (.095"-.105" wall) galvanized steel tubing. 2.875" O.D. RS40 (.160"-.170" wall) galvanized steel tubing.'/N" HR flat steel and 3 1/r" O.D. CF steel bar. (Base) Weldment comprised of 3/s" HRPO sheet steel and 3/11' HRPO sheet steel. (Shock Covers) 16 GA(.060" ) HRPO sheet steel. (Crank Arms & Pins) Fabricated from stainless steel. (Shocks) Gas shocks with foxed bearings. Finish: ProShield', black in color. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) MASTM CR —4 F 879 unless otherwise indicated (see specific prod- C -) uct installation/specifications). Installation Time: (Direct Bury) Concrete Footing - 2 People approx. 3 a hours Assembly - 3 People I how Concrete: (Direct Bury) 9 cu. It. Weight: 499 lbs. Actual Size: Tx 7'(2,13 in x 2,13 m) Area Required: 19'x IV (5,79 in x 5,79 m) ASTM Fall Height: 18" (460 mm) I ) (Direct Bur)) Build and pour concrete footing. Refer to Frame An- choring Details. Allow concrete footing to cure for a minimum of 72 hours before continuing. 2) With Omnspin Spinner frame in position, drill through 4 outside holes in OmniSpin Spinner frame 5 '/1" deep into concrete slab, using '/" masonry bit and hammer drill. Refer to the Frame Anchoring De- tail. 3) Tap 42" x 5 1/r" expansion anchors into drilled holes and secure using 1/3" standard hex nuts with '/r" flat washers. Refer to the Frame An- choring Details. 4) Attach OmniSpin Spinner to OmniSpin Spinner frame, using %" x 3/r" BHCS w/pin and 3/." SAE flat washers. 5) Apply labels as shown. 6) Install protective surfacing before users are allowed to play on the component. Eeo N5451r pxtvnM NItlJ8/30o rtpaw Nl M IIPI0a.A8kdvuvi" 1l 1 t twrdw PKI,W N o_ n CR —4 4f t' f C -) I :< rn a M o Q �+ o Eeo N5451r pxtvnM NItlJ8/30o rtpaw Nl M IIPI0a.A8kdvuvi" 1l 1 t twrdw PKI,W landscape structures - Concrete - Slab Crushed— Aggregate Finished Grade OWN SAFE. NOTE Choow a prolective surlearg malenal iMt (4)'/;' Standard referto Frame Anchoring Detail hes a cml Helghl vela. of .t ledst the IS014001 Flat Washers HawIXU.dgd. t.,Me mael(Ref' ASTM Bowl Spindle— Cer'I lletl F1481.) Frame Assemblv 180814a Unitary Surfacing OmniSpin NOTE: When using unitary sur- facing on crushed aggregate, (4)'/;' Standard referto Frame Anchoring Detail Hex Nuts w/ V;' for loose fill protective surfac- Flat Washers ing. Bowl Spindle— Frame Assemblv (4)'/;' x 5 Expansion Anchors DETAIL Slab Q` 2"/51 Min. e e e • • 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888.574.4578 LSI Install Help 888-4384574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 Document #18384300 Alk landscape structures• SAFETY NOTE (3boose a praeosve sMfatlng materim met ties a Gibul Height W. a M s est me Might of the Highest Ac ssige PaNFall Helghtof"sQecenleWpirl (Ref ASTM F1/81.) 18592800 m r m C.7 Sheet 1 of 2 0 2014 by Landsaape Strkj�l,-es All rjms «served Document #20214900 U landscape structures" F lyw Spin DETAIL FLYWHEEL SPINNER ASSEMBLY SAFETY NOTE C:IXDse a pdBCOve sVlatil�j material IINI has a Cdpwl Heghl Value m at least the height olihe Highest Accessible ParVFell Heigh of theadjacertt equipment. (Ref. ASTM F1481.) 185928a Kids In Motion by Landscape Structures All rights reserved 185927 Flvwheel° Spinner )inner if C> _— r rn o � _- S 0 0 a o landscape structures SAFETY NOTE Chooze a polective sutlaciig material tnzt rias a Cnocal Heign� value of et lease ma IS014001re egn,o veal aoartpipwt(Re ASTM DETAIL Q MINIMUM USE ZONE tasersb Kids In Motion © 2014 by Landsca0e Slruct,es Alingnts reserved Loose Fill Protective Surfacing Minimum Use Zone DETAIL DIRECT BURY 850 Flywheel Spinner Post RockI. 24" Dia. 4i 508 185927 Flvwheel° Spinner Sheet 2 of 2 Document#20214900 N O CJ. n �cr �� a m Ln m Flywheel Spinner Post RockI. 24" Dia. 4i 508 185927 Flvwheel° Spinner Sheet 2 of 2 Document#20214900 W1 landscape structures' Parts List Kids In Motion 185927 Flywheel" Spinner Part # Description Qty. 182495-00 Flywheel Spinner, Specify Color ............................. I 182518-00 Flywheel Spinner Post, Specify Color ..................... 1 186445-00 Flywheel Spinner Assembly, Specify Color............ 1 188876-00 Retaining Compound ................................................. 1 185929-00 Flywheel Spinner Hardware Package ................. 1 100196-00 3/e" x'/s" BHCS w/Pin, SST .................................... 10 100365-00 3/," SAE Flat Washer, SST ....................................... 10 185920-00 2" Shaft Snap Ring .................................................... 1 115176-00 Hard Surface ASTM Warning Label ........................ 1 156847-00 Play Safe Label 5-12 Years ....................................... 1 182212-00 Entanglement Warning Label ................................... 1 182213-00 Hot Surface Warning Label ....................................... 1 Specifications Flywheel Spinner Post: Weldment comprised of 3.500" (88,9 mm) O.D. RS20 (.125") (3,17 mm) wall galvanized steel tubing, Vg" (3,17 tram) thick HRPO steel plate and 1.967" (49,96 mm) O.D. steel shaft. Finish: PmShieldr, color speci- fied. Flywheel 125 lbs. Spinner Assembly: (Wheel) Weldment comprised of 1.315" (33,4 mm) Min. Use Zone.: O.D. RS20 (.080"-.090") (2.03 mm -2,28 mm) wall gal- Concrete: vanized steel tubing, 4!' (6,35 mm) thick HRPO steel Fall Height: sheet and 3.500" (88,9 mm) O.D. steel pipe. Finish: v+ ProShield, color specified. (Bearings) 2" (50 mm) Deep groove stainless steel. Spinner: Rotationally molded from U.V. stabilized linear low density polyethylene measuring 47 '/," (1206 mm) wide x 12 42' (317 mm) high, color specified. Fasteners: Primary fasteners shall be socketed and pinned o tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Installation Time: 5 man hours Weight: 125 lbs. Area Req.: 22'(6,71 m) diameter Min. Use Zone.: 9'(2,74 m) Concrete: Approx. 5.23 cu. ft. Fall Height: 74" (1,88 m) Installation 1) Dig footing as shown. Refer to the Direct Bury Detail. 2) Place post in footing hole. Place a level on post gusset, when gusset is plumb pour concrete footing. Allow concrete footing to cure a mini- mum of 72 hours before attaching flywheel spinner assembly, and overhead spinner to post. NOTE: Post will have to be propped in position, until concrete has cured. 3) Remove cable ties from Flywheel spinner assembly bearings. NOTE: Apply retaining compound to inner race of top bearing. Make sure bearings set against top and bottom of bearing housing. 4) Apply retaining compound to shaft surface, as shown. Place flywheel spinner assembly onto post. Fasten snap ring to post shaft NOTE: A snap ring pliers (not provided) is required to attach snap ring to part shaft. 5) Attach spinner to Flywheel spinner assembly, using 3/s" x'/s" BHCS w/ pin and 3/s" SAE flat washers. Refer to Flywheel Spinner Assembly Detail. 6) Apply labels to post as shown. 7) Install protective surfacing before users are allowed to play on the structure. 1 E000100090o«wnsn0014WM pi.s>tesazsm. Cnanare "umus:oss. .a ii d,.i.. N o_ G'i Z—„ n crs O t7 �� v+ r. m `Dx o `v o 1 E000100090o«wnsn0014WM pi.s>tesazsm. Cnanare "umus:oss. .a ii d,.i.. kk landscape structures` I&M PLAN VIEW 23' S" 7,14 m We -saw Assembly 4) Rung Caps 4 Motion TIM of 601 7TH STREET SOUTH, DELANO, MINNESOTA 66328-8606 888-574-46781.51 Install Help 868-433-6574 LSI Direct 763-972-6200 Int. FAX (763) 972-3186 020151hyl_ands,a�Structurs� All rights reserv�d locuuest #21130500 NOTE a protectives ung materiel Net haul.Choose al lana Cnlical Height Value b st least NB IMSAFETY Might of the Highest Accesaiela parVFall Height of the eG(ecenl equipment (Ref. .rrn.a ASTM Fl,tf37 20735100 We -saw Assembly 4) Rung Caps 4 Motion TIM of 601 7TH STREET SOUTH, DELANO, MINNESOTA 66328-8606 888-574-46781.51 Install Help 868-433-6574 LSI Direct 763-972-6200 Int. FAX (763) 972-3186 020151hyl_ands,a�Structurs� All rights reserv�d locuuest #21130500 k1l landscape structures' (4) Footer Guide Pla (4)'/a" x 11/,' BHCS w/Pin Grey Anti-Sieze (4) a/a" x T/e" BHCS w/Pin Grey Anti-Siez NOTE: Concrete foot- ing should not be larger than outside dimen- sions of anchor cage. Concrete should be flush with top of anchor cage. Concrete Footing Yij DETAIL BUMPER FOOTER ATTACHMENT (4) 1 x 3' Hex Head Botts 737 (4) Bumper Footer c Guide Plates - II -� Subgrade (4) Bumper Footers Kids In Motion 02015 Dy Landscape Swctures All rights reserved Cage Anchor SAFETY NOTE Choose a protective surfacing material Nat Das a Critical Heigh Value si at least the ISO 14U�3 height of me Highest Accessible GaNFall Height of the adjacent equipment. (Ret. c..un•a ASTM F1487) 210877a DETAIL WE -SAW ASSEMBLY ATTACHMENT BI We -saw DETAIL CONCRETE FOOTINGS (WITH FOOTER GUIDE PLATES) 36„ . o K_]il (8) a/e, x 1 t/z, BHCS w/Pin w/ Orange Patch w/ a/e" SAE Flat Washers Cage t (4) Rung Caps Loose FIII Tt C Protective. -� Surfacingn. - II -� Subgrade (4) Bumper Footers Kids In Motion 02015 Dy Landscape Swctures All rights reserved Cage Anchor SAFETY NOTE Choose a protective surfacing material Nat Das a Critical Heigh Value si at least the ISO 14U�3 height of me Highest Accessible GaNFall Height of the adjacent equipment. (Ret. c..un•a ASTM F1487) 210877a DETAIL WE -SAW ASSEMBLY ATTACHMENT BI We -saw DETAIL CONCRETE FOOTINGS (WITH FOOTER GUIDE PLATES) 36„ . o K_]il (8) a/e, x 1 t/z, BHCS w/Pin w/ Orange Patch w/ a/e" SAE Flat Washers Cage eHn - II Subgrade-- 0 Concrete U DETAIL RUNG CAP ATTACHMENT 1(4) 5/1 x 1 1/2 (4) Rung BHCS w/Pin m a 0 Caps w/ Orange Patch r17 S 7(4) Bumper Dooters -- 186490 We -saw" ftCS_: N f0 -.- eHn - II Subgrade-- 0 Concrete U DETAIL RUNG CAP ATTACHMENT 1(4) 5/1 x 1 1/2 (4) Rung BHCS w/Pin m a 0 Caps w/ Orange Patch r17 S 7(4) Bumper Dooters -- 186490 We -saw" IS014001 landscape DETAIL structures WE -SAW ASSEMBLY (8)'/a' x 2' Platform BHCS w/Pi Handhold w!'/e' SAE Flat Teeter Pad Washers (4) ale' x'/a'— _ BHCS w/Pin w/ 1/," SAE (4) Center Pad I Flat Washers Edges I It 2) #14 x 1 '14" 1 BHCS w/Pin I o nsert Centar o _ 000 - Pad OI (8)'/e" Low Crown G Nuts w/'/," SAE Flat Washers (24)3/ a 1 1 x ]/ B 11 , BHCS w/Pin w/ 3/," SAE Flat Washers 1r3r172rn,T/• • DETAIL SEAT ATTACHMENT DETAIL FILLER PLATE ATTACHMENT (2) Filler SAFETY NOTE Choose a protective surfacing malenal Nat Plates has a Chi Height Value of al least the (4)'/a' Low height of the Highest social Pawl'all Crown Cap Height of the adjacent equipment. (Rat. umr.4 ASTM F1487) w/ 3/," SAE 187943b (8)'/a' x 2' Platform BHCS w/Pi Handhold w!'/e' SAE Flat Teeter Pad Washers (4) ale' x'/a'— _ BHCS w/Pin w/ 1/," SAE (4) Center Pad I Flat Washers Edges I It 2) #14 x 1 '14" 1 BHCS w/Pin I o nsert Centar o _ 000 - Pad OI (8)'/e" Low Crown G Nuts w/'/," SAE Flat Washers (24)3/ a 1 1 x ]/ B 11 , BHCS w/Pin w/ 3/," SAE Flat Washers 1r3r172rn,T/• • DETAIL SEAT ATTACHMENT DETAIL FILLER PLATE ATTACHMENT (2) Filler Plates (4)'/a' Low Crown Cap Nuts w/ 3/," SAE Flat Washers N d GIs C:) 7 —,Cqi% —11V NMI• /(J DETAfIlLi RUNG CAP ATTACHMENT We -saw Assembly (2) Filler We -saw BHCS Plates J. Assembly Seats e' x 1'/z' BHCS w/Pin w/ Orange Patch - (12) Rung Caps Assembly (4) 186490 We—saw TM DETAIL (24) #10-24 x Ili' FHMS (12)Footman Loops Sheet 2 o` 3 012015 by Lands�m Sl ware; All rights reserved Document #21130500 structures° DETAIL DIRECT BURY WITH POUR -IN-PLACE SURFACING SAFETY NOTE Choose a protective au NOT material Inas hes a Cul Value at lead lne IS014001 si height d the Highasl Att'assiDle Pal Highest Height of the adjacent equipment (Ref landscape 1coon"e ASTM F1487.) 210877= structures° DETAIL DIRECT BURY WITH POUR -IN-PLACE SURFACING Kids In Motioni • O7 7TH STREET SOU7 iwwmnawzrnESOTA 66526-660 663744676 LSI Install Hel 88458-6674 LSI Dire 65-67232001n Ax (763) 672.516 CONCRETE FOOTINGS (WITH FOOTER GUIDE PLATES) 29" 36 29 _ Concrete �` _ 737 914 737 - 1" 25 Footing e e - ° _--- Bumper Foote oo Guide Plates ::10 r� 1" 0 25 (4) Rung e Caps ° Pour -In -Place Anchor Cage } 1 Surfacing il. ul r Lr - Concrete ab 5 Or = _ Compacted Gravel = Neo 7 Subgrede Subgrade/L Concrete _ 36 914 Concrete. - o (4)Bumper - DETAIL Footers RUNG CAP ATTACHMENT c� < I (4) a/e" x 1 t!z' x'Pl n m BHCS m Sy t��T� i !:-I w/ Orange Pate _ 0 (4) Rung : p Caps (4) Bumper Footers O Kids In Motioni • O7 7TH STREET SOU7 iwwmnawzrnESOTA 66526-660 663744676 LSI Install Hel 88458-6674 LSI Dire 65-67232001n Ax (763) 672.516 U ii l landscape structures' Parts List Part# Description Qty. 181123 Seat, Specify Color .................... ............... ............. __._4 182262 Rung Cap, Bieck .................................................... 16 182458 Platform Handhold, Spocify Color ................ .___._._..I 783 lbs. 182947 Center Pad, Black.... ......................................__._._._._1 211277 GripX Insert, Black ... .............................. ...................... 1 183327 Teeter Pad, Specify Color..............................................1 183328 Pad Edge Long, Specify Color......................................2 183329 Pad Edge Short, Specify Color......................................2 183748 Filler Plate, Specify Color.............................................2 186453 Anchor Cage, Black .......... ........... ._ .............................1 187231 Bumper Footer, Specify Color.......................................4 188068 We -saw Assembly, Black ..............................................1 186951 Footer Guide Plate, Black ........ .._.......... ....._................. 4 208040 Wt -saw Hardware Package......................................1 100173 3/: x 2" BHCS w/Pin, SST............................................8 100196 3/r" x 7/r" BHCS w/Pin, SST ......................................... 28 100201 '/: x 1 '/," BHCS w/Pin, SST -Patch ............................ 24 100365 8: SAE Flat Washer, SST ........................... 48 129500 '/: SAE Flat Washer, SST.............................................8 129672 # 14 x 14"" TORX BHCS, SST .................................... 12 207709 Footman Loop, SST ...................................................... 12 162462 #10-24 x'/:" FRMS......................................................24 115176 ASTM Hard Surface Warning Label .............................1 156846 Play Safe Label. 2-12 Years...........................................1 182212 Entanglement Warning Label........................................1 182213 Hot Surface Warning Labcl...........................................1 100349 3/r" Low Crown Cap Nut, SST .................................... 12 127463 Bit Hex TPP T-27 Torx..................................................1 188123 Bumper Guide Plate Hardware Pickup ................1 127546 3/: x 7/r" BHCS w/Pin, SST.. ........ --- .........................4 127551 '/r" x 1 1/3" BHCS w/Pin, SST........ .. .. .. ......... ............ 4 188124 5/r" x 3" Hex Cap Screw, ZP.... ...... -- ............................4 Specifications We -sax Assembly: (Arm Assembly) Weldment comprised of 3.500" (88,9 mm) O.D. x 8 GA. (.162") (4,11 mm) wall galvanized steel tubing, 2.375" (60,33) O.D. RS40 (.130"-.140") (3,30 mm -3.56 mm) wall galvanized steel tubing, 1.900" (48,26 mm) O.D. RS40 (.120% .130") (3,05 mm -3,30 mm) wall galvanized steel tubing, .375" (9,52 mm) thick HRPO steel plate and .250" (6,35 mm) HRPO steel plate. Finish: Proshield•, black in color. (RockerAssembly) Weld- ment wmprised .250" (6,35 mm) HRPO steel plate and 2" (50 mm) x'/,,," (7,93 mm) wall steel tubing. Finish: ProShield, black in color. (Base) Weldment comprised .375" (9,53 mm) HRPO steel plate and 2.500" (63,50 mm) O.D. x 1.150" (29,21 mm) I.D. stainless steel tubing. Finish: ProShield, black in color. (Base Plate) Fabricated from .250" (6,35 mm) HRPO steel plate. Finish: ProShield, black in color. (Spring) 5 5/r" (142,87 mm) diameter 1J/n," (20,62 mm) tempered alloy steel coil. Finish: ProShield, black in wlor. (Spring Wedge) Cast from ductile iron alloy. Finish: ProShield. black in color. (Bear- ings) 1.145" (29,08 mm) I.D. oilite bronze. (Shaft) 1.14" (28,96 mm) O.D. stainless steel. Filler Plate: Fabricated from 12 Ga. (105") (2,66 mm) HRPO steel sheet. Finish: ProShield, color specified. GripX Insert: 3/," (19.05 mm) Thick Permalener, black in color. Kids In Motion 186490 We-saWTM Teeter Pad & Edges: Permalener, color specified. Platform Handhold: Weldment comprised oft.315"(33,4 mm) O.D. RS20 (.080"-.090") (2,03 mm - 2,28 mm) wall galvanized steel tubing, 10 GA (.135") (3, 42 mm) HRPO steel sheet and 7 GA. (.179") (4.54 mm) HRPO steel sheet. Finish: Proshieldr, color specified. Anchor Cage: Weldment comprised of 1.029" (26,13 mm) O.D. RS20 (.070"-.080") (1,77 mm - 2,03 mm) wall galvanized steel tubing with 203 or 303 stainless steel welded inserts with %" internal threads and 7 GA. (.179") (4,54 mm) HRPO steel sheet. Finish: Proshield", black in color. Rung Cap: Molded from U.V. stabilized black EPDM rubber encapsulating.250" (6,35 mm) thick aluminum sheet and. 125" (3,18 mm) thick aluminum plate. Center Pad: Fabricated from .250" (6,35 mm) thick HRPO steel sheet plate. Finish: Proshield", black in color. Bumper Footer: Weldment comprised of 1.315" (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm - 2,29 mm) wall galvanized steel tubing with 203 or 303 stainless steel welded inserts with'/r" internal threads and .250" (6,35 mm) thick HRPO steel plate. Finish: Proshield•, color specified. Seat: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Fasteners: Primary fnsteners shall be socketed and pinned tam- perproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific product instal lation/specifications). Installation Time: Approx. 16 man hours Fall Height: 54" (1,37 m) Min. Use Zone: 6'(1,83 m) Area Required: 16' 8" x 23'5" (5,08 in x 7,14 m) Concrete Req.: Approx. 17.82 cu. ft. Weight: 783 lbs. N 0 C:) `L7 crt O Ti C7—C —i C'7 1 C71 r :fira r*1 M z�K D CT1 Cn Sheet 3 of 3 Document#21130500 �sot()0393ooave102113050()r3ss 921UMW. Ch."sm ,,X ince"pwtnm er kil- landscape structures Installation Instructions I ) (Direct Bury) Dig footing holes for anchor cage and bumper footers. Build a form for anchor cage concrete footing. Concrete footing for anchor cage should not be larger than outside dimensions of anchor cage. Refer to Concrete Footing Details. 2) Attach rung caps and bumper footers to bumper footer guide plates using'/." x 3" hex head bolts. Refer to the Bumper Footer Attachment Detail. 3) Attach bumper footer guide plates to anchor cage using'/;' x 1 '/r" BRCS w/pin and'/." x V." BHCS w/pin. Refer to the Bumper Footer Attachment Detail. 4) Place anchor cage and bumper footers in footing holes, as shown. Top of anchor cage should be flush with finished grade. With anchor cage level and bumper footers plumb, pour concrete. Concrete should be flush with top of anchor cage. Allow concrete footing to cure for a minimum of72 hours before continuing. Refer to the Concrete Footing Details. 5) Remove footer guide plates from anchor cage and bumper footers. Discard bumper guard plates and hardware. Attach rung caps to bumper footers using'/." x 1 '/r" BHCS w/pin. Refer to the Rung Cap Attachment Detail. 6) Set We -saw assembly onto anchor cage. Line up holes in We -saw assembly bottom plate with threaded inserts in anchor cage. Attach We -saw assembly to anchor cage using Y." x 1'/2" BHCS w/pin with '/." SAE flat washers. Refer to the We -saw Assembly Attachment Detail. 7) Attach Her plates to We -saw assembly using 814x 1'/f BHCS w/pin with'/." SAE flat washers and'/." low crown cap nuts with %" SAE flat washers. Refer to the Filler Plate Attachment Detail. 8) Attach center pad edges to teeter pad, using N 14 x 1 '/4" BHCS w/pin. Refer to the We -saw Assembly Detail. 9) Attach platform handhold. teeter pad, insert and center pad to We -saw assembly attachment plates, using Y." x 2" BHCS w/pin with'/." SAE flat washers and %" low crown cap nuts with'/." SAE flat washers. Refer to the We -saw Assembly Detail. 10) Attach rung caps to We -saw assembly using'/." x I '/r" BHCS w/pin. Refer to the Rung Cap Attachment Detail. 11) Attach seats to We -saw assembly using'/." x'/." BHCS w/pin with'/." SAE flat washers. Refer to the Seat Attachment Detail. 12) Attach footman loops to seats using #10-24 x'/t" FHMS. Refer to the Seat Attachment Detail. 13) Apply Play Safe and warning labels, as shown. 14) Install protective surfacing before users are allowed to play on the structure. Kids In Motion 186490 We -saw'"' N O_ �? n a, i -4 ..� z� =gym �' M � 3 �x o D o landscape structures' Fj NOTE: Roof will rest on top of posts. DETAIL (8) Post— Extensions (8) Post Extensions 'ctm1 Sections (8) Tall Outer (24) 11i1 x a/e" Posts Drive Rivets PLAN VIEW (8) Tall � Outer Posts PlayOdyssey 165596 P © 2010 by Landscape Stmtlures All ngbls reserved SAFETY NOTE Choose it prolacUve lig". material Mal �/� /�/� bas a Cght f the Haijf�t Value of at IeeSt ., IS014001 , HeIgMalM1e aqa eMseq pnaei(Rel ASTM t I I F1481.) Certitietl 16584700 Poly Roof (2) Double Prolective Posts/Ladder'- Surfacing 12' Tower Sheet 1 of 5 Document tt17264600 S & landscape structuress PLAN VIEW/FOOTING LAYOUT SAFETY NOTE F tSTMT) IMa4acenlaquilmiant. (ReI.ASTMB].) 165848b (2) Double Posts/Ladc NOTE: Place #5 re -bar 3" up from the bottonisend 3" down from the top of the concrete, as shown. Rebar should be placed 3" in from the edge of the concrete on all sides and approximately 103/," on center. Concrete Footina With Re -Rod 0 2010 by Landscape Sbuclures All nght reserved. 9/1, landscape structures° Step #1 DETAIL MAINSTRUCTURE ASSEMBLY SEQUENCE Step #2 Step #3 Step #4 Step #5 Step #6 165847f 02010 by LaMsna StWC es. An nghM reserved. Document #17264600 A& landscape structures° DETAIL MAINSTRUCTURE ASSEMBLY SEQUENCE Step #7 165596 PI 0 2010 by Lar so pe &mctures. All ngbls reserved. Step #8 12' Tower 165847g 71 r m 9/& landscape structures° DECK TO DECK 06)%""14" ATTACHMENT BHCS w/Pin (16)'/;' Standard Flat Hex Nuts Wash hers Washers Flat Washers (4) Octagon Sections (2) Double Posts (8) Tall Outer Posts 165847a DETAIL DECK TO TALL OUTER POST ATTACHMENT (4) Octagon Deck ° Sections ° (8) Deck Hanger Post Clamp Assemblies, DETAIL DECKASSEMBLY (BOTTOM VIEM DETAIL SupF DECK SUPPORT ATTACHMENT (4) Deck Supports (4) Octagon Deck Sections 3 7T(8) Outer Attachment Plates (16) a/," Patch Hex Nuts w/Y." SAE (8)'/,;' Nylok Flat Washers Hex Nuts w/%" SAE Flat Washers ��4(4) Octagon Deck BHCSw/Pinw/ /, (16)'/ext'/s' Flat Washers —I �� BHCS w/Pin w/ 3/," / (16) a/e° Standard Flat Washers Hex Nuts w/a/e' Deck (4)'/," Standard Hex Nuts w/'/e' Flat Washers Flat Washers (4) Octagon Deck Sections 020,0 by LarM.c Str Urft. ui n9h,a resarvaa. Document#17264600 9/& landscape structures® (2) Infill (2) Double- Posts/Ladder (4) Octagon' Deck Sections DETAIL INFILL PANELATTACHMENT _ (2) Support Straps (4)'/;' x'/a' BHCS w/Pin w/'/," Flat Washers (8)'/;' Standard Hex Nuts w/14" Flat Washers IGSiIIr '/;' Flange Nuts (4)'/," x 1 Ys' DETAIL BHCS w/Pin w/'/," SAE PIPEBOLT ATTACHMENT Flat Washers (2) 21 '/;' Pipebolts 165847c w/'/;' SAE Flat Washers INOTE: Post pictorially removed for clarity. DETAIL INFILL DECK ATTACHMENT (BOTTOM VIEW) 165596 P '/;' Flange s w/Pin DETAIL INNER UPPER DECK PLATE ATTACHMENT S)'/," x 1 V," BHCS r/Pin w/'/e' Flat Vashers (2) Inners Deck Plates (4) Octagon Deck Sections (4)'/;' Standard Hex Nut W/ 31,11 SAE Flat Washers 12' Tower A# Octagon P,ck Sections C:) "n n t (2) Double s. Post 3 O C) (4) 3/e' x r/e' BHCS w/Pin W/ 3/,-' SAE Flat Washers V — landscape structures (4) Nylon Spacers Double Posts/Ladder 165848d 5' Half (16) %" x 1 a/," BHCS w/Pin PlavOdvssev KOOT VOST. KOOT & bUDDie HSSemw Sheet 02010 dy Landscape St,xtures_AII rights r.se,ed Document #17264600 x/1/1 landscape structures Parts List PlayOdyssey 165596 PlayOdyssey° 12' Tower Part# Description Qty. 100610 '/." x 51," Drive Rivet, AI/SST................................. 16 100611 1/4" x 3/." Drive Rivet, AUSST................................ 24 105327 5" Half Clamp, Specify Color ................................. 24 106022 Deck Hanger Clamp, Specify Color ....................... 16 119883 Bubble.........................................................................1 Q 126900 Poly Roof Section, Specify Color ............................ 2 127914 Roof Post, Specify Color .......................................... 4 128503 Infill Panel, Specify Color ........................................ 2 136366 Infill Deck, Specify Color ......................................... 1 149182 Support Strap, Specify Color .................................... 2 152982 Octagon Deck Section, Specify Color ..................... 8 165206 Outer Attachment Plate, Specify Color .................. 16 165299 Post Extension, Specify Color .................................. 8 165368 Double Post/Ladder, (DB), Specify Color .............. 2 165370 Tall Outer Post, (DB), Specify Color ...................... 8 165501 Deck Support, Specify Color .................................... 8 165725 21 '/." Pipebolt, Specify Color ................................. 2 165726 Inner Deck Plate, Specify Color ............................... 2 165895 Re -bar #5 x 114" long .............................................. 48 130009 Roof Hardware Package., ....................................... 1 100196 3/#" x'/." BHCS w/Pin, SST ..................................... 4 113027 3/#" x 1 3/." BHCS w/Pin, SST ................................. 16 100610 V, x 5/e Drive Rivet, AUSST................................. 8 100611 1/4" x 3/." Drive Rivet, AUSST................................ 12 112501 Nylon Spacer.............................................................. 4 112793 1/16" Flat Washer, SST.. ............................................. 12 123224 3/." x 1 W,4" BHCS w/Pin, SST ............................... 12 165599 PlayOdyssey Tower Hardware Package .............. 1 100196 3/." x'I," BHCS w/Pin, SST .................................... 12 100198 34" x I 'W BHCS w/Pin, SST ................................ 108 100321 3/0' Hex Patch Nut, SST ........................................... 32 100327 3/.' Standard Hex Nut, SST ..................................... 84 100329 5/,6" Nylok Hex Nut, SST ......................................... 16 100351 3/a" T -Nut, SST .......................................................... 32 100353 3/s" Flange Nut w/Pin, SST., ..................................... 8 100362 3/." Flat Washer, SST ............................................... 164 100365 3/#" SAE Flat Washer, SST ....................................... 64 113027 5/." x 1 5/#" BHCS w/Pin, SST .................................. 8 Specifications Double Post: Weldtnent comprised of 5" O.D. x 11 GA (.I 20") gal- vanized steel tubing, 1.029" O.D. RS -20 (.070"-.080") galvanized steel tubing, 1.315" O.D. RS -20 (.080" - 090") galvanized steel tubing and'/,' x l '/4" HRPO flat steel. Finish: ProShield"', color specified. Roof Post: Weldment comprised of 4.675" O.D. x .150" 6065- T5 extruded aluminum and formed 5" O.D. x .125" 6061-T6 extruded altuninum. Finish: ProShield, color specified. Post Extension: Weldment comprised of 4.675" O.D. x .150" 6065- T5 extruded aluminum, formed 5" O.D. x.125"6061 - T6 extruded aluminum and die cast 369.1 aluminum post cap. Finish: ProShield, color specified. Outer Post: Fabricated from 5" O.D. x 11 GA (.120") galvanized steel tubing. Finish: ProShield, color specified. Poly Roof: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Bubble: Vacuum formed .230" x 26/," diameter clear poly- carbonate. Octagon Deck: Flange formed from 12 GA (.105") sheet steel con- forming to ASTM A 1011. Standing surface is perfo- rated with diameterholes. Deck face has (4) slot- ted holes for face mounting components. The com- bined finished size measures 21&" x 106'/:' x 106'/,'. Finish: TenderTuD color specified. Re-bar0: 5/s" Diameter. Nylon Spacer: 3/s" I.D. nylon washer. Pipeboit: Fabricatedfmm 1.125"O.D. 6061-T6aluminum tube, with 34" internal threads. Infill Deck: Flange formed from 12 GA (.105") sheet steel con- formingtoASTMA1011. Standing surface isperfc- rated witb 3/1,' diameter holes. The finished size mea- sures 2 5/,' x 24 3/8" x 24 3/s". Finish: TenderTuff, color specified. Infill Panel: Solid color Permalene", color specified. Inner Deck Plate: Fabricated from '/,' HRPO steel sheet. Finish: ProShield, color specified. Support Strap: Fabricated from '/," x 1 '/f HRPO flat steel. Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 36 hours with 4 people minimum Concrete Req.: Approx. 3.70 cu. yds. Actual Size: 106'/f x 106'/,' (2,70 in x 2,70 m) Weight: 3102 lbs. Fall Height: 144" (3,65 m) Deck Height Eco #54072 D"avnaa,#172646005ep1"ecs#165MM tx ffimai po.a eximsimu 1'.,". ro o_ C-) �, r El Z Q 7C Q q' O Eco #54072 D"avnaa,#172646005ep1"ecs#165MM tx ffimai po.a eximsimu 1'.,". tw landscape structures' Installation Instructions PlayOdyssey 165596 PlayOdyssey° 12' Tower NOTE: To lift deck sections and poly roof, a "Lull" type material handler is recommended. 1) Dig footing, and level ground as shown. Refer to the Plan Yew/ Footing Layout. 2) Step #1 -Attach deck hanger clamps to outer posts at height shown, using 5" half clamps, '/." x I '/e' BHCS w/pin and %" tee nuts. Refer to the Offset Hanger Clamp Assembly Spec Sheet. 3) Attach outer attachment plates to deck hanger clamps, using 5/3." nylok hex nuts with %" SAE flat washers. Refer to Detail. 4) Stand double post/ladder and (2) tall outer posts upright in footing hole. NOTE: Rope may be used to tie off the double post. The use of rope will help keep the double post in plumb position, while attach- ing decks. Tie a rope (not supplied) on each side of the top ladder rung. The rope should be long enough to attach to a ground stake (not supplied). When the double post is in plumb position, pull the ropes tight, and attach to ground stakes. 5) Lift deck section and place onto outer attachment plates, and double post plate. Attach deck section to tall outer post attachment plates, using %" patch hex nuts with %" SAE flat washers. Refer to Detail. 6) Step #2 - Stand (2) tall outer posts upright in footing hole. Lift deck section and place onto tall outer post attachment plates, and double post plate. Attach deck section to tall outer post attachment plates, using'/," patch hex nuts with'/," SAE flat washers. Refer to Detail. 7) Step #3 - Attach infill deck to deck sections, using %" x 1 '/s" BHCS w/pin with %" flat washers and %" standard hex nuts with 3/," flat washers. Refer to the Infill Deck Attachment Detail. 8) Stand remaining double post and (2) tall outer posts upright in foot- ing hole. Lift deck section and place onto tall outer post attachment plates, and double post plate. Attach deck section to tall outer post attachment plates, using 3/," patch hex nuts with'/." SAE flat wash- ers. Refer to Detail. 9) Attach 21 3/," pipebolts to double posts, using 1/," x 7/," BHCS w/ pin and %" SAE flat washers. Refer to the Pipebolt Attachment De- tail. 10) Step #4 - Stand remaining tall outer posts upright in footing hole. Lift deck section and place onto tall outer post attachment plates, and double post plate. Attach deck section to tall outer post attach- ment plates, using 3/s" patch hex nuts with'/," SAE flat washers. Refer to Detail. 11) Attach infill deck to deck sections, using'/." x 1 '/," BHCS w/pin with'/," flat washers and'/," standard hex nuts with 1/." flat washers. Refer to the Infill Deck Attachment Detail. 12) Attach (4) deck sections together, using 3/," x 1 '/," BHCS w/pin with'/," flat washers and 14" standard hex nuts with 14" flat wash- ers. Refer to the Deck Assembly Detail. 13) Attach (4) deck supports to decks, using'/a' x I'/," BHCS w/pin,'/," x I Y." BHCS w/pin,%" flat washers and 31." standard hex nuts. Refer to the Deck Assembly Detail. 14) Step #5 -Attach remaining (4) deck sections to tall outer post attach- ment plates, using 'I," patch hex nuts with 'I," SAE flat washers. Refer to Detail. 15) Step #6 - Attach infill panels to double posts, using support straps,'/." flange nuts and 3/," x 1 '/e" BHCS w/pin with 1/g" SAE flat washers. Refer to the Infill Panel Attachment Detail. 16) Attach (2) inner upper deck plates to deck sections, using 3/," x '/," BHCS w/pin with'/," SAE flat washers and'/," standard hex nuts with 14" SAE flat washers. Refer to the Inner Deck Plate Attachment Detail. 17) Step #7 - Place post extensions onto tall outer posts. Drill through holes in tall outer posts and into post extensions with a'/," or "F" (only) drill bit. Insert'/f x'/s" drive rivets into holes and hemmer rivet pins in until it is flush with heads. Refer to Detail. 18) Step #8 - Attach the bubble to the roof using nylon washers between the bubble and the roof and'/," x'/e' BHCS w/pin. Refer to the Roof Post, Roof & Bubble Assembly page. 19) Insert the roof posts into the double posts. Refer to the Roof Post, Roof & Bubble Assembly page. 20) Assemble the roof using'/," x I "/,s' BHCS w/pin with '/16" flat washers. Refer to the Roof Post, Roof & Bubble Assembly page. NOTE: Stand roof upright on its side for easiest assembly. 21) Position roof on roof posts with a minimum of 6 people and fasten using 5" half clamps and 3/," x 1 3/," BHCS w/pin. Refer to the Roof Post, Roof & Bubble Assembly page. NOTE: Roof will rest on top of posts. 22) Using the holes in the double posts as guides drill through holes with a '/f or "F" only drill bit. Insert 'Q x'/s" drive rivets in holes and I ammer drive rivet pin in until flush with head. Refer to the Roof Post, Roof & Bubble Assembly page. Finishing Steps 23) Install'/."x'/." drive rivets in all 5" half clamps. Referto the Typical Offset Hanger Clamp Spec Sheet. Refer to the Roof Post, Roof & Bubble Assembly page. N 24) With posts plumb and decks level, pourVtcrete footing. Let con- crete cure for 72 hours before ] a efetyt the P iew/Footing Layout. NOTE: Make sure Re nis plc(c in concYAe as shown. 25) Install enclosures/play comporM M'fis shotvn on yronaite drawings. Cr% 26) Install protective surfacing bef'q�tMers are allowo�tp play on the structure. _ f*'1 �' i � � 3 Y cri rn Sheet 5 of 5 Document #17264600 landscape structures` (4) Typical Hanger Cla Assemblies T C T C 11 1 1 1 C E_R TIiIE0 SAFETY NOTE Goose a protective surfaorq material that has a Crieul Height Value of at lean t1b height of the Highest Accessible P.VF Height of" agecantepnprbrR. (Red. ASTM Ff4B].) 16630000 (4) spa, x z tff4, BHCS w/Pin t 166302 Upper Pine Barrier A tD UT CT l a 1 CD ©2001) by Landscape Structures All rights reseNea Document ttl6630000 ki?, landscape structures PlayBooster-0 166302 Upper Pipe Barrier Parts List Installation Instructions Part# Description Qty. 100610 '4" x 5/." Drive Rivets, AUSST ............................... 4 105327 5" Half Clamp, Specify Color .................................. 4 113729 Offset Hanger Clamp, Specify Color ....................... 4 166196 Upper Pipe Barrier, Specify Color ........................... 1 166470 4- Clamp Barrier Hardware Package .................. 1 100198 5/." x 1 '/." BHCS w/Pin, SST .................................. 8 100203 5/.. x 2 '/." BHCS w/Pin, SST .................................. 4 100351 '/," Tee Nut. SST ........................................................ 8 Saecifications Upper Pipe Barrier: Weld,uentconhprisedofl.315"O.D.RS20(.080"-.090" wall) galvanized steel tube with 203 or 303 stainless steel welded inserts with 5/:' internal threads, and 12 GA. (.105") steel pipe cap. Finish: ProShield°, color speci- fied. Clamps: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: %manhour Weight: 49 lbs. 1) Attach the offset hanger clamps to the posts at height shown, using 5" half clamps and'/." x I '/," BHCS w/pin with r/." tee nuts. Refer to the Typical Offset Hanger Clamp Spec Sheet. 2) Attach Upper Pipe Barrier to offset hanger clamp assemblies, using °/." x 2'Q' BHCS w/pin. 3) Install drive rivets in half clamps per the Typical Offset Hanger Clamp Assembly Sheet. 4) Install protective surfacing before users are allowed to play on the structure. N O Cf. � < r �m a I D p A& landscape structures' 144" Deck Straight Section Typical PlayBooster Post Top 0 Po 144" TopesDe Elbow Section (LH) Straight Section SAFETY NOTE has a e a pal Height aWlia o Material leas Nat has a Critical MFET NO of el least Ne eight by Me Highest Acxassible Part�al; IS014001@I, °(Ra AiM Cerlietl Po481.) 17789200 ENTRANCE SECTION Entrance Section DETAIL (2)Typical Offset Hanger Clamp Assemblies Entrance Section DETAIL ENTRANCE SECTION ATTACHMENT T Entrance (4) Va" x 7/a" ,� I \ Section BHCS w/Pin w/ a/." Flat Washers (2) a/;' X 2 y,, BHCS w/Pin. Straight Section "Mid -Support Straight Section Elbow Section (R H) Protective I I Surfacing 114" Mid -Support 11 NOTE: / Refer to your plan drawing for location of footings 82" Mid -Support and layout and direction of SlideWinder sections. PlayBooster° 165780 Tower SlideWinder2 02011 by Landscape Structures All nghls reserved Post 3 407/1," Rail Section Sheet 1 of 2 Document #17789200 j & landscape structures DETAIL TYPICAL SLIDE SECTION (2) x/e" x 1 °/is" BHCS w/Pin w/ 3/," Flat Washers (3)'/s' x 1 n/a" BHCS w/Pin w/ 3/;' Flat Washers Typical Mid -Support DETAIL TYPICAL MID-SUPPOR-Cjn BOTTOM VIEW -.ter m PlavBoosterl 165780 Tower SlideWinder2 Details 2)11 by Landscape SN,cwres FII fights reserved 154547a0 J & landscape structures° Top Of Sliding Surface Loose Fill-,% Protective -31+ Surfacing :+t, `$ . o n Crushed Rock SAFETY NOTE Choose a protective surtaang material that has a Cntical Height VaLe of at least the height of the HighestAaessi6le Pan all Heightethe a4aosnt equpmerX. (Rel. ASTM F14e7) DETAIL DIRECT BURY I EXIT SECTION DETAIL tsaszab DIRECT BURY/ MID -SUPPORTS (3) Mid -Supports Exit Loose Fill Section Protective NOTE: Exit Heights may vary if the pro- tective surfacing is not level. Do not put pressure/tension on the entrance section when adjust- ing the exit height. NOTE: The SlideWindel2 is de- signed so the user can exit to the rig ht or left. Refer to the Site Plan for footing locations and direction of SlideWinder2. 144" Deck 7 2003 (2) a/e" Flat Washers (2) Rubber Bushings (2)3/;' Flat Washers ° (2)'/;' x 1 '/;' Subgrade BHCSw/Pin Concrete— Bolts oFooting ncrete Limited Thread Bolts g ° Crushed Subgrade Rock �12" 'I 300 Exit Footer NOTE: Attach bolts in the center of the footer slots to allow for Concrete expansion and contraction. Footing Snug bolts down only, do not 12" overtighten! ,Ann 3990 PLAN VIEW/FOOTING LAYOUT 237 Ve" Typical Concrete Footing 1 872440 Min. Use Zone . 0 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-5744678 LSI Install Help 888438-6574 LSI Direct 763-972-52001n1. FAX (763) 972-318! Document #17789204 Milk landscape structures" Parts List Part# 100583 105327 113729 124864 124867 124868 124876 124877 128261 128077 166079 166026 100610 132443 121371 100196 100362 124342 100198 100203 100351 128373 100292 100362 111442 Description 40'/„" Rail, Specify Color 5" Half Clamp, Specify Co: Offset Hanger Clamp, Spec Straight Section (30 '1," Lo Elbow Section (RH), Speci Elbow Section (LH), Specie Exit 146" k '/4" x', Spacer PlayBoosterr�' 165780 Tower SlideWinder2 Qty. ........................................ 1 ........................................ 2 Color............................. 2 , Specify Color ............. 6 :olor ............................... 1 'olor ............................... 1 9r.................................... I Entrance/Deck Mounting Hardware Package ......... 1 3/e" x 7/e" BHCS w/Pin, SST...........................................4 3/6" Flat Washer, SST.. ....................... ............................. 4 Rail Hardware Package ................................................ i 1/e" x 1 '/a" BHCS w/Pin, SST ........................................ 4 5/s" x 2 1/4" BHCS w/Pin, SST... ..................................... 2 3/a" Tee Nut, SST.............................................................. 4 Exit Support Hardware Package (DB) ...................... 1 1/e" x 1 /4" BHCS w/Pin Limited Thread Bolt, SST .... 2 5/." Flat Washer. SST.......................................................4 RubberBushing...............................................................2 154942 SIIdeWinder Section Hardware Package..................9 100362 3/," Flat Washer, SST ...................................................... 45 113027 3/f x 1 3/," BHCS w/Pin, SST ....................................... 27 123224 1/e" x 1 "/1a" BHCS w/Pin, SST ..................................... 19 DB = Direct Bury RH = Right Hand LH = Left Hand Specifications Slide Sections: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Rail: 1 '/" O.D. 6061-T6 aluminum extrusion with watts. Finish: ProShield', color specified. Spacer Tube: Fabricated from 1.3125 O.D. x 16 Ga. (.065) steel tubing. Finish: ProShield, color specified. Mid -Support: Weldment comprised of 1.900" O.D. RS -20 (.090" - .100") galvanized steel tubing and 3/16 11x 1 1/4" zinc pplated steel strap. Finish: ProShield, color specified. Exit Footer: Weldment comprised of 2.375" O.D. RS -20 (.095" -.105") galvanized steel tubing and 1/" x 3" x 7 1/ " mounting plate. Finish: ProShield, color specified. Offset Hanger Clamp Assy.: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamppe roof in design stainless steel /SST) per AS"1 M1 879 unless otherwise indicated (see spe- cific product installation/specifications). Installation Time: 4 man hours with 2 people Concrete Req.: 5.25u.ft. Weight: 321 lb$. Fall Height: 144" (3,65 m) Installation Instructions 1) Refer to the Site Plan for footing locations and direction of SlideWinder2. 2) Dig footing holes spaced as shown. Refer to the Direct Bury Exit Section and Direct Bury Mid -Support Details. 3) Place 40 7/1," rail through entrance section, place spacer tubes over each end of the 40 Yn" rail, attach offset hanger clamps using'/R' x 2 1/4" BHCS w/Pin. 4) Attach entrance section to the face of the deck using'/s" x'/a' BHCS w/Pin and 3/s" flat washers. 5) Attach offset hanger clamps to posts, using 5" half clamps,'/," x 1 1/," BHCS w/Pin and 3/e" tee nuts. Refer to the Typical Offset Hanger Clamp Spec Sheet. 6) Attach SlideWinder straight section to entrance section loosely, start- ing in the middle and working your way to the outside of each section, using 3/e" x 13/," BHCS w/Pin with 3/e" flat washers on the 3 inside holes and 3/s" x 1 "/16' BHCS w/pin with 3/s" flat washers on the 2 outside holes. When all bolts are started, pull the tops flush with each other and tighten. Add remaining Slide Winder seclions.The left elbow section reads (LH) and the right elbow section reads (RH). Refer to the Typical Slide Section Detail. 7) Attach mid -supports to slide using 3/e x 1 3/s" BHCS w/Pin. Refer to the Typical Mid -Support Detail. 8) Attach exit footer to base of slide using 3/s" x 1 1/j' BHCS w/Pin limited thread bolts, 3/1" flat washers, rubber bushings and 3/8" flat washers. NOTE: Attach bolts in the center of the slots to allow for expansion and contraction. Snug bolts down only, do not overtighten. See Direct Bur)JExit Section Detail. 9) With supports plumb pour concrete footings. Allow concrete foot- ings to cure for a minimum of 72 hours before users are allowed to play on the structure. 10) Install protective surfacing before users are allowed to play on the structure. �291 rgcu [#177892X0 sepleas#16582800.A pacer tubes NP List. C- cn C-) r'7 9 C' tT O �291 rgcu [#177892X0 sepleas#16582800.A pacer tubes NP List. V _ landscape structures PlayBooster (6)Typical Offset/ Tall Bubble Hanger Clamp Panel Top Ot Clamp A ° TOP Of Game to �ri'a �r m Tog of ° Clamp 00 O O 0 0 Kick Plate Octagon Hex Deck (2) a/a' x'/e' BHCS (2) a/;' Standard w/Pin w/ a/;' SAE Hex Nuts w/ e/ee Flat Washers SAE Flat Washers Play.Booster® . 0 2009 by Landscape Structures All rights reserved SAFETY NOTE Choose a protective surtaclng matanal Nat has a Critical Height Value of at least the height of the Highest Accessible ParVPall IsO� Certified F148lof lheeQacent equipneM. (Ref ASTM DETAIL 16582300 PANELATTACHMENT Hanger C Offset Hanger Clamp Assemblies (6)a/;' Flange—CA 1 Nuts w/Pin (12) s/s. Nuts w/1 Bubbli T P Tall B Panel x 3 3/1 w/Pin DETAIL BUBBLE ATTACHMENT Use (12) Nylon Spacers Panel ,/e " x °/e', S w/Pin lie DETAIL KICK PLATE ATTACHMENT (2) °!;'xs/;' BHCS w/Pin w/ a/a' SAE Flat Washers Kick Document#16582300 Tall Bubble o Panel r� 0, r Mile M (2 M_, Flangi C!7 Nuts w/Pin ON Document#16582300 kih landscape structures° Parts List PlayBoostei-O 165824 Tower Bubble Panel Parti! Description Qty. 100610 '/," x'/," Drive Rivets, AWSST ............................... 6 105327 5" Half Clamp, Specify Color .................................. 6 113468 Spacer Tube, Specify Color ...................................... 6 113729 Offset Hanger Clamp, Specify Color ....................... 6 119883 Bubble.........................................................................1 12 165820 Tall Bubble Panel, Specify Color ............................. 1 165821 Kick Plate, Specify Color ......................................... 1 115385 Bubble Hardware Package .................................... 1 100195 3/8" x 5/a' BHCS w/Pin, SST .................................... 12 100353 '/," Flange Nut w/Pin, SST ...................................... 12 112501 Nylon Spacer............................................................. 12 165822 Tall Permalene Panel Hardware Package .......... 1 100195 '/," x'/e" BHCS w/Pin, SST ..................................... 2 100196 3/," is 7/," BHCS w/Pin, SST ..................................... 2 100198 %" x I Y." BHCS w/Pin, SST ................................. 12 100327 '/," Standard Hex Nut, SST ...................................... 2 100351 '/," Tee Nut, SST. ...................................................... 12 100353 '/," Flange Nut w/Pin, SST ....................................... 8 100365 '/," SAE Flat Washer, SST ........................................ 6 124460 '/,' x 3'/4" BHCS w/Pin, SST .................................. 6 Specifications Permalene" Panel: Solid color panel measures 35 %" wide x 71" high, color specified. Bubble: Vacuum formed .230" x 26'/," diameter clear poly- carbonate. Nylon Spacer: 3/s' I.D. nylon washer. Spacer Tube: Made from 6061-T6 aluminum 7/a' O.D. x I Finish: ProShieldv, color specified. Kick Plate: Fabricated from 11 Ga. (.120"). Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: 1 man hour Weight: 72 lbs. Installation Instructions I ) Attach bubble to tal I bubble panel with panel laying on its backside. Position the (12) nylon spacers over the panel holes. Place the (12)'/," x '/," BHCS w/pin through the bubble holes, lower bubble onto panel and secure using'/," flange nuts w/pin from backside of panel. 2) Attach offset hanger clamps to posts at height shown, using half clamps and 34' x 1 '/s" BHCS w/pin and with 34" tee nuts. Refer To The Typical Offset Hanger Clamp Assembly Sheet, 3) Attach kick plate to the face of the deck using'/;' x 7/a' BHCS w/pin with'/j' SAE flat washers and'/," standard hex nuts with'/," SAE flat washers, as shown. 4) Attach tall bubble panel to kick plate and offset hanger clamp assem- blies using'/," is 3 3/." BHCS w/pin, spacer tubes and 1/g" flange nuts w/pin. See Kick Plate Attachment Detail. 5) Attach tall bubble panel to offset hanger clamp assemblies using 3/," x 3'Q' BHCS w/pin, spacer tubes and'/," flange nuts w/pin. See Panel Attachment Detail. 6) Install protective surfacing before users are allowed to play on the structure. N O cn 2� :<r'— X.-M O 9/& landscape structures® DETAIL ENTRANCE SECTION ASSEMBLY (2) Typical Entrance Offset Hanger _ Section Clamp Assemblies Post Top of (24) %" x T/a" 144" Deck BHCS w/Pin 155" 1 w/ a/;' Flat Washers 86" h 104" dhm ISO 14001 Typical Play Booster Post ' -- ' (72) %11 x 1 t/a" BHCS w/Pin W/ a/a' Flat Washers ' Entrance Section s: ' (3) Straight Tunnel Sections 0 SAFETY NOTE Choose a protective surtatirp metenel tltet hese Critical Height Value of atleast the height of Me Highest Accessible PaNFell He ightoftheaQamnlepuprtlent (Ref ASTM F11H7J 16583000 DETAIL TUNNEL SECTION (72) Attachment Blocks ,View Tube Assembly (Optional) Lip %" Standard Nuts NOTE: Center arrow with top of straight sec- tion. NOTE: Line up arrows when connecting slide sections. (4) Spiral Tunnel Sections NOTE: Center arrow with toptf straight sec - 407/1511 Rail M BHCSw/Pin DETAIL (2) Rail k,D Spacers FACE MOUNT ATTACHMENT Deck-- _ Entrance Section (4) D/a" x 7/e " BHCS w/Pin ah Flat Wasshers W / DETAIL ENTRANCE/EXIT SECTION (24) %" x T/a" 144" Deck BHCS w/Pin 155" 1 w/ a/;' Flat Washers 86" h 104" dhm ISO 14001 Typical Play Booster Post ' -- ' (72) %11 x 1 t/a" BHCS w/Pin W/ a/a' Flat Washers ' Entrance Section s: ' (3) Straight Tunnel Sections 0 SAFETY NOTE Choose a protective surtatirp metenel tltet hese Critical Height Value of atleast the height of Me Highest Accessible PaNFell He ightoftheaQamnlepuprtlent (Ref ASTM F11H7J 16583000 DETAIL TUNNEL SECTION (72) Attachment Blocks ,View Tube Assembly (Optional) Lip %" Standard Nuts NOTE: Center arrow with top of straight sec- tion. NOTE: Line up arrows when connecting slide sections. (4) Spiral Tunnel Sections NOTE: Center arrow with toptf straight sec - Exit Protective Surfacing p•• '� 165827 Tower• •Sheet 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888-438-6574 LSI Direct 763972-52001n1. FAX (763)98-3185 Document #20454600 c -3 -jn M k,D Ut +T Exit Protective Surfacing p•• '� 165827 Tower• •Sheet 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888-438-6574 LSI Direct 763972-52001n1. FAX (763)98-3185 Document #20454600 landscape structures PLAV VIEW/FOOTING LAYOUT 165830b =1t-� I rn �— �m 3s m (5::o o 0 0 PlayBoosterO 165827 Tower Turbo Twistei'm 607 7111STREET SOUTH, DELANO, MINNESOTA 553288605 888-574-4678 LSl Install Hel 888-438-6574 LSI Dimt 763-972-52001nt. FA% 63 972,3185 V & landscape structurese DETAIL MID -SUPPORT UO (8) 1/," Low Crown Cap Nuts DETAIL w/%" Flat Washers MID -SUPPORT DIRECT BURY Loose Fill Protective Surfacing Subgrade ---- Concrete ---- Crushed, Rock 12" 300 DETAIL DIRECT BUI Flange (8) 3/," x 1 Y." BHCS w/Pin w/ 3/," Flat Washers Lower Top of Sliding Upper SAF NOTE — — ooa� materValue of at height of Ne HighestA¢essible ial q a6 2 -se a protective � ' h.. . Critical bb- Height Hei 204546a DETAIL EXIT SECTION SUPPORT DETAIL EXIT SECTION SL Exit Section (2)3/." Flange ---- - ---- 2-/50 Nuts w/Pin ��� Loose Fill SC ion Protective Surfacing Em"upport 4 (rm Bury) (2)3/," Flat Washers Subgrade E (2)Rubber Bushings' M (2)3/," SAE Flat, Exit Support Washer a I x 1 1/" (2)3/811 a BHCS w/Pin--- cn E)Jt Support Concrete DO NOT OVERTIGHTEN Crushed Tr Rock 7/ 300 PlayBooster'll' 165827 Tower Turbo Twisterr" Sheet 2 of 3 =1111111VAGIM I � 101 .111.1111_11111.�_% TLyrij.1 nmyllFr.iTt.EFslr� C 2014 by Landscape StmcWfeg All rights reserved Document #20454600 U� landscape structures DETAIL COVER ATTACHMENT (SHOWN FOR REFERNCE ONLY) PlayBooster" Optional View Tube, 32" Section 02014 by Landsca SVupures. All dgnls resernea 12s77oao '/4.' X 3/," :S w/Pin /," Flat lhers 3/e" Nylon ;ers kil" landscape structures' Parts List PlayBoostet-0 165827 Tower Turbo Twisterr" Part# Description Qty. 100583-00 40 7/,a" Rail, Specify Color. ...................................... 1 100610-00 '/," x 54" Drive Rivet, AL/SST................................. 2 105327-01 5" Half Clamp, Specify Color .................................. 2 111716-00 Exit Support (DB), Specify Color ............................ 1 113729-00 Offset Hanger Clamp, Specify Color ....................... 2 127687-00 Tunnel Slide Section, Specify Color ....................... 4 127694-00 Entrance Section, Specify Color .............................. 1 127695-00 Exit Section, Specify Color ...................................... 1 127699-00 32" Straight Section, Specify Color ....................... 2/3 132443-00 Rail Spacers, Specify Color ...................................... 2 133047-00 Attachment Block, Specify Color ........................... 72 166036-00 Tunnel Mid -Support 68", Specify Color ................. 1 166080-00 Tunnel Mid -Support 86", Specify Color ................. 1 166083-00 Tunnel Mid -Support 104", Specify Color ............... 1 166074-00 Tunnel Mid -Support 155", Specify Color ............... I 125629-00 View Tube Assembly (Optional), Specify Color .... 1 111704-01 Exit Support Hardware Package .......................... 1 100353-00 3/," Flange Nut w/Pin, SST ....................................... 2 100362-00 3/," Flat Washer, SST ................................................. 2 100365-00 3/," SAE Flat Washer, SST ........................................ 2 111442-00 Rubber Bushing......................................................... 2 113027-00 3/," x 1 3/," BHCS w/Pin, SST .................................. 2 121371-00 Entrance/Deck Hardware Package ...................... 1 100196-00 3/," x 7/," BHCS w/Pin, SST ..................................... 4 100362-00 3/," Flat Washer, SST ................................................. 4 124342-00 Rail Hardware Package .......................................... 1 100198-00 3/," x I o," BHCS w/Pin, SST .................................. 4 100203-00 3/," x 2'/4" BHCS w/Pin, SST .................................. 2 100351-00 3/i' Tee Nut, SST ........................................................ 4 204573-00 Turbo Twister 144" Deck Hardware Package ... 1 100196-00 3/d' x 7/," BHCS w/Pin, SST .................................... 24 100198-00 3/," x 1 '/," BHCS w/Pin, SST ................................. 80 100327-00 3/," Standard Hex Nut, SST ...................................... 72 100362-00 3/." Flat Washer, SST ................................................ 114 100349-00 3/," Low Crown Cap Nut, SST .................................. 8 DB — Direct Bury Specifications Tunnel Section: Rotationally molded from U.V. stabilized linear low- density polyethylene, color specified. Attachment Blocks: U.V. stabilized high-density polyethylene, color speci- fied. Mid -Support: Weldment comprised of 1.900" O.D. RS -20 (.090" - .100") galvanized steel tubing and 1/i," x I '/4" zinc plated steel strap. Finish: ProShield', color specified. Exit Support: Weldment comprised of 2.375" RS -20 (.095" - .105") galvanized steel tubing and'/," x 4" x It 3/f mount- ing plate. Finish: ProShield, color specified. Rail: 1 Y." O.D. 6061-T6 aluminum extrusion with 3/," walls. Finish: ProShield, color specified. Clear Cover: Drape formed .177" x 30" x 47 %" clear polycarbon- ate. RailSpacers: Fabricated from 1.3125 O.D. x 16 Ga. (.065) steel tub- ing. Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 4 hours with 2 people Concrete Req.: Approx. 9 cat. ft. Area Req.: 11'(3,35 m) minimum use zone at exit Weight: 486 His. 498 His. w/ one view tube Fall Height: 12'(3,65 m) (Deck Height) Installation Instructions 1) Dig footing holes spaced as shown. 2) Insert 40 7/16" rail through top of entrance section, place rail spacers over each end of the 40 7/76" rail and attach to offset hanger clamps using 3/." x 2'/4" BHCS w/Pin. 3) Attach entrance section to the face of the deck using 3/," x 7/," BHCS w/Pin with '/e" flat washers. Refer to the Face Mount Attachment Detail. 4) Attach offset hanger clamps to posts, using 5" half clamps,'/." x 1 '/," BHCS w/Pin and 34" tee nuts. Refer to the Typical Offset Hanger Clamp Spec Sheet. 5) Fasten straight tunnel section to the entrance section using'/." x 7/811 BHCS w/Pin with 3/," flat washers. Refer to the Entrance/Exit Sec- tion Detail. 6) Fasten tunnel slide sections together, using 3/8" x 1 '/," BHCS w/Pin with 3/," flat washers and attachment blocks with %" standard hex nuts on regular tunnel section side. NOTE: Line up arrows when connecting slide sections. 7) Attach mid -supports to the slide sections shown, using 34" x I BHCS w/Pin with %" flat washers and 3/a' low crown cap nuts with 3/," flat washers. Refer to the Mid -Support Detail. 8) Fasten exit section to tunnel slide sections,using 3/a' x 7/r" BHCS w/ Pin with 3/." flat washers. Refer to the Entrance/Exit Section Detail. 9) Attach exit support to exit section using 3/," x l 3/," BHCS w/Pin, I/," SAE flat washers, rubber bushings, 3/1" Ps washers and 3/a' flange nuts w/Pin. NOTE: Attach bolts in the &%ter of the slots to allow for expansion and contraction�i n' ug boWdowm only, do not over - tighten. Refer to the Exit Sectiiin-S�pokRetail. 10) With supports plumb, pour cor? ekfnonpgs. All ncrete foot- ings to cure a minimum of 72 he�rAeformsers ak allowed to play on the structure. _< *t m 11) Install protective surfacing befin3wrs a*allowlmt ? play on the structure. :*E+X t..0��✓ y to M rco aoiooisr u«umrnr pzws4on eep� nt65s3eea. xrvW="e corm 7w�,i,r s,raw,re wrknse. st& IS0dr14001 Am landscape structuress Typical PlayBooster F.S,AFET.YNOTE mecovesurtatirgatenalThalVNeeFallTM 165960 Tower Pipe Barrier 16596100 ripe larrier lat 0zoos by Lar scope stmaures. All nghts reserved. Document#16596100 kb, landscape structures° Parts List PlayBooster-O 165960 Tower Pipe Barrier Part# Description Qty. 100610 '/," x 5/." Drive Rivets, AUSST ............................... 2 105327 5" Half Clamp, Specify Color .................................. 2 113729 Offset Hanger Clamp, Specify Color ....................... 2 165887 Tall Pipe Barrier, Specify Color ............................... 1 114309 Reil Hardware Package .......................................... 1 100198 3/." x 1 '/." BHCS w/Pin, SST .................................. 4 100203 5/." x 2 3/." BHCS w/Pin, SST .................................. 2 100351 3/." Tee Nut, SST ........................................................ 4 100610 '/." x 5/." Drive Rivet, AUSST................................. 2 132743 Deck Mount Barrier Hardware Package............ 1 100198 3/." x 1 '/." BHCS w/Pin, SST .................................. 2 100327 3/." Standard Hex Nut, SST ...................................... 2 100365 3/." SAE Flat Washer, SST ........................................ 4 Specifications Tall Pipe Barrier: Weldmentcomprisedof 1.315' O.D.RS20(.080"-.090" wall) galvanized steel tube with 203 or 303 stainless steel welded inserts with %" internal threads, 1 '/.' x 2" x 3/36" steel angle and 12 GA. (.105') steel pipe cap. Finish: ProShield'r', color specified. Clamps: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct immilation/specifications). Installation Time: 3/. man how Weight: 82 lbs. Installation Instructions 1) Attach the "fall Pipe Barrier to the face of the deck using 3/." x 1 '/." BHCS w/pin with'/." SAE flat washers and 3/." standard hex nuts with'/.' SAE flat washers. Refer to the Barrier Attachment Detail. 2) Attach the offset hanger clamps to posts, using 5" half clamps and'/." x I '/.' BHCS w/pin with 3/e" tee nuts. Refer to the Typical Offset Hanger Clamp Spec Sheet. 3) Attach Tall Pipe Barrier to offset hanger clamp assemblies, wing 1/s" x 2'/f BHCS w/pin. 4) Install protective surfacing before users are allowed to play on the structure. N O zES2 U n Z E o �^ o 0 A141 landscape structures, (14) Po: Toppers 1 1 1 CERTIGIF9 SAGETYNOTE Ch. a taca a surlstl' hui anal Nal has a C.'iWi H fight Wlue of at lead Ne aepfll d the HQhest Accessible P.—, HeigMol Ne aejarnnleouioo+ent (del. ASTM F14ez) 19496300 DETAIL BRACE TO OUTSIDE POST ATTACHMENT (28)'/e" a" Crown ( Nuts w/ let Flat We DETAIL DIRECT BURY 193169 Netale)(° . 14 -Post Mainstructure ®2014 by laMswDe 9mcmres Nlhts reserved. (7) Posts Steel Clamps mr U V [/ i✓ landscape structures NOTE: Attach clamp posts before standing t. upright. Refer to your cific climber spec shee clamp locations. 1 1 1 ctr,liFiEc DETAIL BRACEATTACHMENT SAFETY NOTE P. CM1wse a pMeclive swlatiig rtwleM1el iMl M1as a Cdifal HHgM1I Value of al Irasl Me d Ne Hpned Aasssak PaNFaA HegMdNeaGlaAnleRuipnml. (Rei ASTM FfdBL) 194963a Conoco VT POSTS 193169 Netplex`H t 14 -Post Mainstructure 02014byleMerapeS dlres. AIInghMm% . D. 0 a (2) Post NOTE: See Your Site Plan for Toppers location and orientation of Vibe Roofs. DETAIL VIBE ROOF (OPTIONAL) (7)3/e x r/e BHCS w/Pin w/ a/." SAE Flat 193169 Post Vibe (2) 30" Roof Post Extensions (2) f/i x3/a" Drive Rivets 114 x a/e ve Rivets 220" Roof (2) 30" Roof Post Extensions (2) Roof Clamps U_ rV 0 E O cn 0 (2) 220" ve ets m° F Roof Posts t� $ (8)'/a" x 1 v t7 01 i a BHCS w/Pia�f'- rn _m t a 1 12 f� Die)c a 14 -Post Mainstructure'' (n sheet: C 2014 by wed.... 9mcvrea AIng11sresarvab Document#21493200 SAFETY NOTE cnoo e. �aurva Y NOTA .nal u a J U(,^//n( n... cmfa Halem vawa of ei �eaaf m. S0 .� w 0'0^ neipM al Ne Hlpneal Arueealble P.NFaII I eaElemM.Quq..ent.(Rai.ASTA1 NV YIW1 landscape F1487) ® carman F1�aT) structures" DETAIL 94�Ze EXPLODED VIEW n 0 a (2) Post NOTE: See Your Site Plan for Toppers location and orientation of Vibe Roofs. DETAIL VIBE ROOF (OPTIONAL) (7)3/e x r/e BHCS w/Pin w/ a/." SAE Flat 193169 Post Vibe (2) 30" Roof Post Extensions (2) f/i x3/a" Drive Rivets 114 x a/e ve Rivets 220" Roof (2) 30" Roof Post Extensions (2) Roof Clamps U_ rV 0 E O cn 0 (2) 220" ve ets m° F Roof Posts t� $ (8)'/a" x 1 v t7 01 i a BHCS w/Pia�f'- rn _m t a 1 12 f� Die)c a 14 -Post Mainstructure'' (n sheet: C 2014 by wed.... 9mcvrea AIng11sresarvab Document#21493200 U% landscape structures` Parts List PlayBooster° 193169 Netplex", 14 -Post Mainstructure Part# Description Qty. 100610-00 '/; x'/; Drive Rivet, AL/SST................................. " 100611-00 '/," x 1/; Drive Rivet, AL/SST................................. " 104731-00 1 3/," Steel Half Clamp, Black ................................. 14 177021-00 Vibe Roof, Specify Color .......................................... 178724-00 Infill Panel, Specify Color ........................................ 178725-00 Roof Clamp, Specify Color ....................................... 190360-00 14 -Post Brace, Black ........ - ...................................... 14 192691-00 Post Topper, Specify Color ...................................... 14 194151-00 30" Netplex Roof Post Ext., Specify Calor ............ 195955-00 220" Netplex Roof Pont, Specify Color .................. a 196003-00 204" Netplex Post, Specify Color ............................ 196004-00 182" Netplex Post, Specify Color ............................ a 179611-00 Vibe Roof Hardware Package ............................... 100196-00 '/r" x 1/." BHCS w/Pin, SST ..................................... 7 100198-00 Y." x 1 V," BHCS w/Pin, SST .................................. 8 100365-00 1/; SAE Flat Washer, SST ........................................ 7 196025-00 14 -Post Netplex Hardware Package ..................... 1 100198-00 3/; x 1 '/." BHCS w/Pin, SST ...................... --...... 56 100349-00 3/; Low Crown Cap Nut, SST... .............................. 56 100365-00 14. SAE Flat Washer, SST ...................................... 112 214919-00 Spare Pan. Kit NETPLEX................... ..... _.......... ....... I 100349-00 3/8' Low Crown Cap Nat, SST...................................4 100290-00 3/8" x 7/8" BHCS 61P LTHD, SST ............................2 127179-00 5/8 OD X3/e LG, Bu.h,SST.......................................2 192064-00 6LP MS FLG NUT, SST .................................... — A 192071-00 6LP Mex24 BHCS mm. SST ................................ _..A 113027-00 3/80-3/8i BHCS 6LP, SST .......................................8 127551-00 318x1 -1/2i BHCS6I.P,SST......................................A 100292-00 3/8x1-1/4 BHCS 61, I.THD, SST.................................2 156%2-00 513 OD X 1/21.0 Ranh, SST......................................2 " = Quantity Determined By Your Order Specifications Post'Ibpper: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. infill Panel: Made from 12 GA. (.105") (3,18 mm) thick HRPO steel sheetzincplated. Finish: ProShield*, color speci- fied. Vibe Roof: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified Post: Sce PlayBoostera (PB) General Specifications. Roof Clamp: Cast alurninum. Finish: ProShield, color specked. Rope System Brace: Weldmentwmprisedof1.900"(48,26rtim)O.D.RS40 (.120"-.130") (3,05 mm -3,30 mm) wall galvanized steel tubing, and '/," (6,35 mm) thick HRPO steel. Finish: ProShield, black in color. Half Clamp: Steel. Finish: ProShield, black in color. Fasteners: Primary fasteners shall be socketed and pinned tampapmofin design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- uct insmllation/specifications). Installation Time: Approx. 28 man hours (with Post Toppers) Approx. 2 man hours for each Vibe Roof Concrete: 49.42 cu. fl. Height: 172" (4,36 m) top of post toppers without roof posts 212" (5}8 m) top of post toppers with roof posts Area Required: 25-4'/," x 25'-8" (7,27 in x 7,82 m) Weight: 1756 lbs. (no Roofs) 2221 lbs. (with 3 Vibe Roofs) 2447 lbs. (with 5 Vibe Roofs) 2757 lbs. (with 7 Vibe Roofs) Installation Instructions (Direct Bury) Layout & Direct Bury Detail. Attach 4 post braces to inside post at height shown. Refer to the Brace Attachment Detail. NOTE: Attach clamps toposis before stand- ing them upright. Refer to your specific climber spec sheel for clamp locations. Stand post with braces upright in footing hole. Continue attaching braces and posts, until structure is fully assembled. Attach outside posts to post braces. Refer to the Brace To Outside Post Attachment Detail. Place post toppers onto posts, as shown. Using hole in post topper as a guide, drill 4," hole into post. Insert'/," x 3/s" drive rivet into drilled hole and tap pin in until it is flush with rivet head. With post plumb, pore concrete footing. Allow concrete footings to care for a minimum of 72 hours before users we allowed to play on the structure. Install protective surfacing before users are allowed to play on the componenPig footings as shown. Refer to the Site Plan Footing (Optional Vibe Roof) Fasten infill panel to roof, u=9 x '/a' BHCS w/pin and 3/." SAE flat washers. N@'E: See lair Site Plan for location and orientation of Vibe RoofsF t7 CD C-3 }y Place 30" roof extensions onto roof poste Usin hore'r1in 30" wa post extensions as a guide, drill'/," holes%-T&t. IpLert'/," drive rivets into drilled holes and tap piilsiMail I is flush i h rivet heads. —<m b rn Attach roof to posts at dimension showirite=F�r to Vibe jlesj Detail.0 Using the predrilled '/," holes in roof clamps as a Ifte, drill holes into posts. Insert '/," x'/n" drive rivets into d.1["ed holes and tap pin in until it is flush with rivet head. Place post toppers onto posts, as shown. Using hole in post topper as a guide, drill'/." hole into post. Insert'/," x 3/r" drive rivet into drilled bole and rap pin in until it is flush with rivet head. landscape structures 1 X11 CEATIFIEO SAFETY NOTE UW59 a pdecOw wnwnq nutena! mal lug a of t" IQi S Value a al leas) me heipM of IM Hiptxsi Accesside PanlFill HeipMdl &Jxenlepipe (Ref ASTM F148]J Surfacing able p Rung ter Cable !-00 #3 i4-00 #3 4-00 #2 3-00 etail #2 #1 4-00 POSTSSOLD SEPARATELY PlayBoostW 194659 Disc Nef Climber, 14 -Post Sheet I e 601 7TH STREET SOUTH, DELANO, MINNESOTA 66328-8605 888.674.4678 LSI Install Help 888-438-6674 LSI Oireet 763-972,5200 Int. FAX (763) 974-3786 , Document #208i/1 A& landscape structures° 8AFEi`/MO7! CMosa a prdeUsa eu�IYl� m IS014001 M"ylafCie•4remaWP'nerk ® F14BT.) e•run•a STEP #1 194659 Disc Net" Climber. 14 -Post 0 2015 Ey LsNsr SUWd s. NI ngMs msenea. �n PZ� M2 m A& landscape structures° SAFETY NOTE Choose a prolective aur/acing material that has a Cdlical HtigM Value M at least the IS014001 IT arulad STEP #2 ss q w a e Im #A* mmom DISC 3 'i no r� 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-5744678 LSI Install Help 888-438-6574 LSI Direct x A& landscape struetures® E Disc Net Ii SAFETY NOTE Choose a protective sutfaaN material Mat has a Cn6ral Height Value of at least the IS014001 He dMe,e Highest ent(Re,AaM Cerli'IeG F1487.) STEP #3 � a � � I at ' I QW Q_ 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-5744678 LSI Install Help 888-498-6574 LSI Direct a& landscape structures` M 00 P SAFETYNOTE IghChoose a protective sWaang material that has a Crural Height Value of al least Ne ►sht�'tHighest eeJj tMwt (Ref ell Cer�t��letl F1487) STEP #4 Disc Net I : It » Mat iiilavBoostee •g• • Disc Nef be14-Post Sheet3 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888574.4678 LSI Install Help 888438.6574 LSI Direct 763-972-6200 Int. FAX (763)972: Document #2081 J SAFETY NOTE J Choose a proved ve lAilong material hat �/� has a CriticalHeight Highest Value of at least the I� 1401 , He grit ofheigh ' the the agacenteQu pmenchl(ReC STM landscape � Certified F"e structuress STEP #5 Top Inner Cable 193011-00 (7) Vertical k Cables E 193120-00 too 0 i; IWO i Step #6: Attach outer cables to clamps, alternating be- tween outer core posts and inner core posts. Refer to Sheet #1. PlayBooster° 194659 Disc Nett"Climber, 14-Post 20151,y Landscape 5[mctures NI rights reserved. 9/& landscape structures, Post#1 173 '/2 4407 134' 340 103 '/,' 2629 94 %* 2400 76" 1931 55'/= 1409 DETAIL CLAMP PLACEMENT 170'/," 4330- 131" 3327 114" 99"_ 2515 84" 2134 65" 1651 Post #2 173'/, 4407 134" 106 %" 2705 8911'.. 2273 75 '/," 1918 58 '/," 1486 SAFETV NOTE Choose a proleava sunaanq material taa� has a Critical Haight Value of l least tall IS014001 , He'IgHdt eWj&a&etaifui t.(RNaAaM Certified F148).) 196045d Post #3 CD r o _ —n GN t D c DETAIL ROPE CLAMP ATTACHMENT (2) a/e" X 1 t/" _._ BHCS w/Pin Rope Clamp Clamp 0.. U U 0.. u u 0" _U LJ Front Back Front Back Front Back NOTE: Clamps shown on O ° back view face center of Disc o 0 Net Climber. Back Clamp Rope Clamp PlayBooster® 194659 Disc Net'" Climber, 14 -Post O,(HS Dy L.Macape Strvr9wes. M nphLa resanrea. Post #4 173 1/z' 170 '/i' 4407- 4330 131" I I I 3404 114" 2896 101" 2565 113 '/;' 2883- 97 tYN 70" - j IM_I •,.. E.E. DETAIL CLAMP PLACEMENT Pastry 170 AIX 12 33 11 28 1( 2E 8 21 5 1[ Post#7 Post#6 11173 4407-- 134" 3404 118 1/i' 3010 101 112'. 2578 196045e 79 Ili' 2019 tYN 70" - 1778 O O C11 n 7 a 0 0 o 0 011 -1— I1 0" 1 11 0" - - 1 u Orr_ Front Back Front Back Front Back Front Badc NOTE: Clamps shown on (Ei back view face center of Disc �_Net Climber. ° Back Clamp Rope Clamp PlayBoostet4 194659 Disc Net'" Climber, 14 -Post 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-5744678 LSI Install Help 888438-6574 LSI Direct 76 0 2015 by LarxIscape Structures. All n" reserved. A& landscape structures° Post #8 170 4331 131" 3327 114" 2896 98" 84„ 2134 58" 1473 173 44C 1: 3,t 118' 301 94 ' 24C 821, 209 70' 175 r height of the Highest Accessible PaNFall'�O® ed HeiE14ght of the, etllecenteplipmerd. (ReL ASTM Post #9 Post #11 196045f 170 V; 4331 131" 118" 2946 1011, 2565 78'' 1981 58" 1473 Post#10 173'/z' 4407 134" 3404 39 '/,-- 2273 77 65 '/;' 1664 0" 1l U 0•_u U On' -I 0.. u u Front Back Front Bade Front Back Front Back NOTE: Clamps shown on o back view face center of Dias o Net Climber. Bi Clamp Rope Clamp D ETA I L SAFETY NOTE Choose a protecow surfaung material that has a Critical Height Chloe of ':Fat, the CLAMP PLACEMENT j2h-y!6OOi f7 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-5744678 L51 Install Help 888-438-6574 L51 Direct 763-972-5200 Int. FAX (7 63) 972-3185 Document #20811301 N V C7 1/," 1113 2883--1 m I r r -n 39 '/,-- 2273 77 65 '/;' 1664 0" 1l U 0•_u U On' -I 0.. u u Front Back Front Bade Front Back Front Back NOTE: Clamps shown on o back view face center of Dias o Net Climber. Bi Clamp Rope Clamp D ETA I L SAFETY NOTE Choose a protecow surfaung material that has a Critical Height Chloe of ':Fat, the CLAMP PLACEMENT j2h-y!6OOi f7 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-5744678 L51 Install Help 888-438-6574 L51 Direct 763-972-5200 Int. FAX (7 63) 972-3185 Document #20811301 170'/, 4331 131" 3327 116" 2946 100" 2540 84" 2134 58" 147; Post#12 DETAIL CLAMP PLACEMENT Post #13 1731/," 4407 134" 3404 106 '/,- 2705- 94 /,"2705 94 '/," 2400 771/,- 1969 71/z1969 58 '/z" 1486 170'/,' 131" 3327 115" 2921 99" 2515 84" 2134 65"_ 1651 Post#14 u u u u u 0 Front Back 0 Front Baric 0 Front NOTE: Clamps shown on o 0 back view face center of Disc Net Climber. C:D o 0 Baric Clamp Rope Clamp PlayBooster° 194659 Disc Net" Climber, 14 -Post ® 2015 by -.nds ape SvucWres_ NI ngnts resew O O k& landscape structures• Side Yew Face Post (2)'/i x 1 31, Ill w/Pin (Leave Loo") Disc Net Climber (Top View) Post#9 Post # Post # 1 I Is� DETAIL #1 FACE CLAMP ATTACHMENT (2) °/a' X 1 x/." BHCS w/Pin i -� Face Clamp NOTE: Make sure logo on face clamp is in upright po- sition. Alternate tightening of (4) bolts to ensure face clamp is tightened evenly. Post #6 #7 (�� � �� 0 M OLIN Poll /li [lost #4 a�¢tr rara C1pd. • ota.dir ..hoYq mil MI 1 n.., awral�wu.aarw n. nrpw a ut. Hyt.1 Aawd. n,ruFr li.iatah aQvl.pipnwt Qc.r. ASTM H987.) Side View Post #13Post 41 Post #2 Postl2 12 W __�_ Post # 14 la BOoster4 194659 Disc Net" Climber 14 -Post 0 2015 by Laii&w a Stw,.,es. All tlgbls reserved. ■ I.. Rivet NOTE: Do not install rivets until Disc Net Climber has been fully assembled. Sheet 6 of 7 Document #2081130( All landscape structures - %11 x 1'/,' BHCS w/Pin Limited Thread Bolt Lin Spacer Cable Bok 1 11 CFRTIFLEO DETAIL #2 CABLE TO CASTING PLATE ATTACHMENT '/a" O.O. X%" Long Bushings Rope Clamp I DETAIL Single Tab T -CONNECTOR ATTACHMENT Casting Plate M8 x 24 mm Vertical Cable BHCS w/Pin\/ J�8 Flange Nut Poet SAFETY NOTE Clgose a protecaw sulfeang melena) Nat lies a CriVCPI HeipM1l Value of al bazl IM1e napOt of iM1e H�pM1esl Accesaida PaNFall Mei�td Vie al}eunlpuprneril. (aet. ASTM FlaB)) 194964( Clamp DETAIL CABLE TO CABLE ATTACHMENT '/e" x 1 V,' BHCS w/Pin Limited Thread _1 Vn! T -Connectors NOTE: Do not overt ighten �c—, rn { fasteners. M C:) 3 PlavBoosterl' 194659 Disc Net''Climber, 14 -Post O 2015 by Lends ape Svr uxW s All ngMt, reserved. BHCS w/Pin \ �4i'/a" x 1'/a. Limited BHCS w/Pin Thread w/'/a" SAE Flat Washers DETAIL Single Tab T -CONNECTOR ATTACHMENT Casting Plate M8 x 24 mm Vertical Cable BHCS w/Pin\/ J�8 Flange Nut Poet SAFETY NOTE Clgose a protecaw sulfeang melena) Nat lies a CriVCPI HeipM1l Value of al bazl IM1e napOt of iM1e H�pM1esl Accesaida PaNFall Mei�td Vie al}eunlpuprneril. (aet. ASTM FlaB)) 194964( Clamp DETAIL CABLE TO CABLE ATTACHMENT '/e" x 1 V,' BHCS w/Pin Limited Thread _1 Vn! T -Connectors NOTE: Do not overt ighten �c—, rn { fasteners. M C:) 3 PlavBoosterl' 194659 Disc Net''Climber, 14 -Post O 2015 by Lends ape Svr uxW s All ngMt, reserved. SLIT landscape structures^ Mat (36) 3/." Flange Nuts w/Pin DETAIL MAT ATTACHMENT (36) 3/e' x 1 3/•" BHCS w/Pin (56) 31." Flange Nuts w/Pin (56) 3/p' X 3/t / BHCS w/Pin w/ %" SAE Flat Washer SAFETY NOTE (' " a Pfd•piw •Xfaraq ftit 1 Vut has a cfro He1pM V a N Nut trb height of a Hphaat Acreaafeb Pat*01 Hegltdx aJjerxfaeq,ipn (Ref.ASTM F1481.) 196045z W O.D. (4) Disc Nets_ C� r / (28) Mat Fastener 2 (4) 54" O.D. Mats (28)3/e„ X t t/ �, BHCS w/Pin o Limited Thread (28) Bolt Links (28) Bolt Link (28) Mat Spacers Fasteners \ (28)'/e' 0. D. x 1/; Long Bushings (28)3/," x 3/j' BHCS w/Pin -- Limited Thread PlayBoostW 194659 Disc Net"'Climber, 14 -Post Sheet 7 of - 601 7TH STREET SOUTH, DELANO, MINNESOTA 66328.8605 8885744678 LSI Install Help 8884384574 LSI Dimet 763.97252001nt FAX (/63) 9723185 Document #2081130M I?, PlayBooster' 194659 Disc Net" Climber, 14-Post landscape structures' Parts List Installation] ime; Approx. 38 man hours Part# Description Qt)'. 100610 '/; x 5/: Drive Rivet, AL/SST.... 98 Weight: 782 lbs. 127551 5/; x 1 '/: BHCS w/Pin, SST ....... 168 Fall Height: 96" (2438 mm) 138915 Bolt Link. SST... .... _ ......................... ........... 60 190194 54" O.D. Mat, Black.................................................. 4 191086 T-Connector, Aluminum........................................... 84 Installation Instructions 193011 Top Inner Cable, Black.............................................. 1 193120 Vertical Cable, Black............................ 7 196883 Top Ring Outer Cable, Black ....__ ____ 14 1) Attach clumps to posts. Refer to Rope Clamp Attachment Detail. 193438 Mat Ring, Specify Calor ................... 24 193912 14-Post Top Outer Cable, Black ...... ........ ........ ........ 2 2) Assemble mats. Refer to the Mat Attachment Detail. 193984 Rubber Mat Fastener, Black.................................... 28 3) Starting with the bottom mat, attach mats to single tab casting plates. 193985 194082 Rubber Mat Fastener 2, Black._.............................. 28 Casting Plate Single Tab, Specify Cola................ 32 Refer to the Detail M2 Cable to Casting Plate Attachment Detail. 194434 Cable 3, Black................ .... -..................................... 2 4) Attach top cables. Refer to the Detail N I Face Clamp Attachment and 194464 Cable 1, Black. ..................................................... ..... I Cable to Cable Attachment Details. 203694 Disc Net w/Clevis Ends, Black................................ 4 195033 Cable 2, Black............................................................ 1 5) Attach vertical cables. Refer to the T-Connector Attachment Detail. 195922 5" Rope Clamp, Specify Cola ............................... 119 195942 5' Face Clamp, Specify Cola...............................- 87 6) Attach outer cables. Refer to the Face Clamp Attachment and Cable 195943 5' Back Clamp, Specify Color -......_...._ ................ 49 to Cable Attachment Details. 196029 14-Post Disc Net Climber Hardxare Package ... 1 7) Install '/," x 5/s" drive rivets in 5" rope clamps. Drill through hole in 100195 1/; x 4: BHCS w/Pin, SST... ..... ........................... 56 5" rope clamps and into 5" post with a'/," or "F' (only) drill bit, 100290 1/: x 7/; BHCS w/Pin Limited Thread, SST ........ 60 insert drive rivet in hole through clamp and into post. Hammer drive 100353 1/; Flange Nut w/Pin, SST...................................... 92 rivet pin in until Hush with head. Refer to the Rivet Detail. 100365 1/," SAE Flat Washer, SST...................................... 184 113027 5/; x 1'/; BHCS w/Pin, SST ............. .................. . 512 8) Install protective surfacing before users are allowed to play on the 156962 5/; O.D. x % Long Bushing, SST......................... 60 structure. 192064 M8 Flange Nut, SST ........................... ............__._.. 42 192071 M8 x 24 mm BHCS w/Pin, SST ...... .._.._._..... _..... 42 196319 Bolt Link Spacer, Aluminum................................... 60 100292 1/e" x I '/: BHCS w/Pin Limited Thread, SST...._ 64 Specifications Rubber Mat Fastener: Fabricated from 4." (9,53 mm) HRPO steel plate. Fin- ish: ProShicK black in color. Rubber Mat Fastener2: Fabricated from'/,"(3.17mm) HRPO steel plate. Fin- ish: ProShield, black in color. Mat Ring: Permalene", color specified. N Casting Plate: Weldnient comprised of 1/s" (9,53 mm) HRPO steelO cn � i `n plate and '/," (6,35 nurn) HRPO steel plate. Finish: _ t� Pori color specified. () Clamp: 369.1 Aluminum. Finish: PmShield', color specified 01 M Mat: .315"(8,00 mm) Thick mini rough top rubber belting :<<�*., r with polyester fabric plys, black in color. ;..) 7-1 J ZEY Cable Assembly: (Gble)Made oftightly woven polyester-wtappeQ six- stranded galvanized-steel cable with a polypropylene o core. (Cable Connectors) 6063-T6 aluminum. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainlesssteel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct inslallation/speciftcations). Em OIOUIO)Quummi?U811100 replxa196U1500 Reola diene, S & landscape structures® PlavBoosterp SAFETY NOTE Choose a protective surfacing material that 9hM /�/� hes a Critical Height Value of at least iha ll ISO 14001F , Heeight otight tthe adiacentthe sequi�pnernt l(Re SRTM Ge I'lee F1481.) ,668,000 166809 E -Pod° y.X spa Drive Rivet C 2009 by Landscape Structures. All rights reserved Document #18681000 N O_ CiYJ co � C o —71 r U1 d Casting —' y.X spa Drive Rivet C 2009 by Landscape Structures. All rights reserved Document #18681000 U U�l landscape structures• J'\I NSTSPE0SPEM1M16681000.P65 Parts List Park Description 154461-00 E -Pod, Specify Color ................ 156806-00 Pod Casting, Specify Color ..... 156968-00 Pod Hardware Package ......... 100198-00 '/e" x 1 '/e" BHCS w/Pin, SST. 100610-00 '/." x'/." Drive Rivet, ALSST Qty- 1 ty 1 4 1 Specifications E -Pod: Rotationally molded from U.V. stabilized tinear low density polyethylene, color specified. Pod Casting: Fabricated from sand cast alloy 356 in accordance with ASTM B26. Finish: ProShielda, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST)per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). InstaOation'nme: Approx. r/4 man hour Weight: 11 lbs. Fall Height: Pod Height PlayBooster' 166809 E -pod' Step Installation Instructions 1) Attach a -pod and pod casting to post as shown, using'/." x I '/."BHCS w/pin. 2) Drill through hole in pod casting and into post with a Y." or T" (only) drill bit. Insert'/." x'/r" rivet in hole and hammer rivet pin in until it is flush with head. 3) Install protective surfacing before users are allowed to play on the structure. !i n D� cn o 4 n-< =tc� t m r-- :< m a m � = 0 o CD landscape structures` 0 1 1 1 cEnrlrleo DETAIL SAFETY NOTE Choose a p� surfedrig "Wel that has a tribal Haight Value of at bast the height of the Highest Accea401e PaNFNI Height of the adjacent equipment (Ref. ASTM Fta87.) 20167000 .C.• W 193174Sol Spinner Sheet I of 017TH STREET SOUT ELANO. MINNESOTA 55328-860 88-574-4678 LSI Install Hcl 88-47865]4 LSI Dirac fi3-9725200 In A% p67� 9]2-318 Document #211307011 0 MO -� C,3Cn 1 r Spinner cn —t; .C.• W 193174Sol Spinner Sheet I of 017TH STREET SOUT ELANO. MINNESOTA 55328-860 88-574-4678 LSI Install Hcl 88-47865]4 LSI Dirac fi3-9725200 In A% p67� 9]2-318 Document #211307011 9/& landscape structures DETAIL SOL SPINNER ASSEMBLY NOTE: Hole in bushing needs to be in line with hole in support arm be- fore tightening. I If (2) l/ x I/= 1 BHCS w/Pin (2) Bushings NOTE: Use the slot in the bottom of the bushing to align hole in bushing with hole in su000rt arm. (8) 'l x 1 '/z FHCS (8) 3/1 SAE Flat Washers Spinner DETAIL GRIPX PANEL ATTACHMENT 1 e — (8) a/e" Low Nuts /,a' Crown Cap (2)' x 1/2" BHCS w/Pin ill SAFETY NOTE Chose a ical Heigh sValue o malelidl F fres a Critical Haigh Value of le least 0e +w 0/�0+ height IN the Highest jace Acequip lent (Ref ISO �Wi Height of the adjacent equipment (Rel. Catlllba ASTM F1481.) 202841b M DETAIL CABLE ATTACHMENT Panel#2 NOTE: Hole in bushing needs to be in line with hole in housing before tightening. NOTE: Use the slotbushing 1/ Foote�� bottom of the bushing to align hole in bushing with hole in housing. PlayBooster" 193174 Sol SpinnerTM f 0 2015 by Landscape Structures All rights reserved (8) '/a" x T/e" BHCS w/Pin Limited Thread 61-972-62061n AX (763) 672.316 N CJ oc, C 1 C-) �r- L�-�� f n D o U 61-972-62061n AX (763) 672.316 IS G/ 1 landscape structures` PLAN VIEW/FOOTING LAYOUT Gusset (For Leveli Subgrade Footer Concrete Crushed Rock PlayBooster I ZBEEIZZIMM Ego= C 2015 by Landscape Structures. All rights reserved SAFETY NOTE Choose a potechva surfacing mD has a Critical Height Value WISO14001 height of the Hig"st Ac taloHeight of the adjacent equlla coun.a ASTM F1a87.1 194968b DETAIL SURFACE MOUNT Gvro Twist Post (4)'/;' Standard Hex Nut w/'/;' Flat Washer (4)'/2' x 2 a/."/ Expansion Anchor Concrete Slab Crushed Rock ��.18 46 460 NOTE: Sufficient protective surfacing must cover hard- ware to satisfy fall height requirements. DETAIL FOOTER ATTACHMENT O C-) - Sol Spinner gp t Assembly r , 3 X Loose Fill mTy, ':. Protective Surfacing ��.18 46 460 NOTE: Sufficient protective surfacing must cover hard- ware to satisfy fall height requirements. 4 Sol Spinner TNI of 88328.860 88�74d876 L81 InstaHel 88 38-8674 LSI M 83-972-5200 In Ax (783) 972-318 Document #21130700 N 0 n O C-) n 3 X �o D U1 4 Sol Spinner TNI of 88328.860 88�74d876 L81 InstaHel 88 38-8674 LSI M 83-972-5200 In Ax (783) 972-318 Document #21130700 Az) landscape structures' Parts List Part# Description Qty" 100610 '/," x 5/; Drive Rivet, AL/SST......................................2 6'(1,83 m) minimum use zone 105327 5" Half Clamp, Specify Color.......................................2 Weight: 157092 Footer, (DB). Specify Color ........ ........................... ...... I 160514 Gyro Twist Post, (SM), Specify Color .......................... l 186027 Spinner UHMW Bushing..............................................4 194601 Sol Spinner, Specify Color .............. ._.......................... 1 211278 GripX Panel #1, Black...................................................1 211279 GripX Panel #2, Black ............. ._....... ...........................1 195050 Cable, Black- .... ___ .....................................................3 195055 Support Ann, Specify Colw...._.... .................... ........... 1 203431 Sol Spinner Hardware Package .... ............................ I 100196 3/." x'/." BHCS w/Pin, SST _ .. ........................ ............. 4 151421 3/." x 1 %' FHCS, SST..................................................8 100290 3/." x'/." BHCS w/Pin Limited Thread, SST................6 100349 e/." Low Crown Cap Nut, SST..............._._._._............8 100351 Y. T-Nuts,SST.......__...._....... ._._...._ .......................4 100365 3/: SAE Flat Washer, SST.............................................8 127179 5/: O.D. x 3/: Bushing. SST. ........................................ 6 131849 $/,: it % BHCS w/Pin, SST.. ...... ................................ 4 121348 ,-Hole (SM) Hardware Package .___ ..... .._..... ___ 1 100266 '/," x 2%* Expansion Anchor.......................................4 100322 '/2" Standard Hex Nut, SST...........................................4 100363 '/2" Flat Washer, SST.....................................................4 DB - Direct Bury SM - Surface Mount Specifications Support Arm: Weldment comprised of 2.375" (60,33 mm) O.D. RS40 (.130"-.140")(3,30 mm - 3,56 mm) wall galvanized steel tube, 2.750" (69,85 mm) O.D. 1018 steel, and '/," (6,35 mm) 14RPO flat steel. Finish: ProShield', color specified. Cable Assembly: (Cable) Made of tightly woven polyester -wrapped, six -stranded galvanized -steel cable with a polypmo pylene core. (Cable Connectors) 6063-T6 alumi- num. Sol Spinner: Weldment comprised of 1.900" (48.26 mm) O.D. RS20 (.090"-.100"x 2,29 mm -2,54 mm) wall gal- vanized steel tube, 1.660" (42,16 mm) O.D. RS40 (.111"-.121")(2,82 mm -3,07 mm) wall galvanized steel tube, 1/4" (6,35 mm) HRPO steel plate, 3/:' (9,53 mm) HRPO steel plate, 2.750"(69,85 mm) O.D. 1018 steel, and I'/," (47,63 mm) steel ball. Finish: PmShield, color specified. GripX Panels: Permalene', black in color. Bushing: Oil -filled UHMW PE. Footer: Weldment comprised of 2.375" (60,33 mm) O.D. RS40 (.130"-.140"x3,30 mm - 3,56 mm) wall gal- vanized steel tube, 12 Ga. (.105") (2.67 mm) HR flat steel and I '/," (47,63 mm) steel ball. Finish: ProShield, color specified. Clamps: Cast Aluminum.Finish: ProShielde', colorspecified. Fasteners: Primary fasteners shall be socketed and pinned tam- perproof in design. stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). PlayBooster' 193174 Sol Spinner"' Installation Time: (DR)Approx. 3 man hours (SM) Approx. 21/4 man hours Min. Use Zone: 6'(1,83 m) minimum use zone Concrete Req.: (DB) Approx. 2.94 cu. R. Weight: (DB) 128 lbs. (SM) 126 His. Fall Height: 17" (432 mm) Installation Instructions 1) (Direct Bury) Refer to the Site Plan for Plan Yew Footing Layout. 2) Attach GripX panels to Sol Spinner. Refer to the GripX Panel Attach- ment Detail. 3) Attach support into to posts at height shown. Refer to Detail 4) Place a bushing on each side of the footers l'/," hall, as shown. Insert footer with bushings into Sol Spinner. Align holes in bushings with holes in housing. When holes are aligned, insert 5/,a" x'/2" BHCS w/ pin. Refer to the GripX Panel Attachment Detail. NOTE: Use the slot in tyre bottom of the bushing to align holes. 5) Place a bushing on each side of the Sol Spinners 1 r/." ball, as shown. Insert Sol Spinner with bushings into support arm. Align holes in bushings with holes in housing. When holes are aligned, insert '/,"' x 1/2" BHCS w/pin. Refer to the Sol Spinner Assembly Detail. NOTE: Use the slot in the bottom of the bushing to align holes. 6) Attach cables to Sol Spinner using 5/," O.D. bushings and 'I," x %" BHCS limited thread bolts w/pin. Refer to the Cable Attachment Detail. 7) (Direct Bury) Place a level on the footer gusset, when gusset and 5" posts are plumb, pour concrete footings. Allow concrete footings to cure a minimum of 72 hours before users are allowed to play on structure. NOTE: Sol Spinner assembly will have to be propped in position, until concrete has cured. (Surface Mount) Drill %" x 3" deep holes through gyro twist post plate using hammer drill and '/2" masonry bit. Tap expansion anchors into drilled holes. Fasten gyro twist post to expansion anchors using '/2" standard hex nuts with'/3" flat washers. 8) Install 1/4" x'/8" drive rivets in 5" half clamps. Drill through hole in half clamps and into 5" post with a'/," or "F" (only) drill bit, insert rivet in hole and hammer rivet pin in until it is fluWwith head. 9) Install protective surfacing before uwram allovN to plax.an. the structure. ty D� -4 C-) -< I �n m -<r- 7, PU I, O = �7C O O CD Fro X IN393 Document 21130"!00rtp1xu20345000. 0.,d Gnpxpanelpen numbers. k& '_ y landscape structures° OWN SAFETY NOTE Ctpose a protecOve surfaung malenal mat has a Cnucal Height Value of atleast Ne Height of the Highest Accessible PaNFell Height of the adjacent equipment. (Ref ASTM F1487J 21278500 j Post (2) Mounting 108" Steel Pates PlayBooster / Post 4) Cables (2) ShaftNOTE: Attach belt Mounts with textured side up. I t I � I I I I I I I I (2) W Par -- D C7 DETAIL alfa' Pa elsom Clamps DIRECT BURY \ o Loose Fill Protective Surfacing OF I Protective Surfacing [CA Crushed Rock Booste 193176 Boogie Board"" Sheet 1 of 2 01, 7TH STREET S0 ELANQ MINNESOTA 5588 860 B8-574-0678 LSI htstall Hcl 88-478-6574 L=! 6J-972-5200 In A% p6Jl 972318 02015 byl-andscailpe Structures Ail(ightsreseived Document #21278500 1�l landscape structures Parts List PlayBooster" Fun 193176 Boogie Board'" Part# Description Qty. 100610 '/: x%' Drive Rivct,AUSST.................._.__...__..__2 105327 5" Half Clamp, Specify Color.._._._................_...._.....2 140619 108" Steel Post w/Cap, 42" DB, Specify Color ............. l 194220 Belt, Specify Color........................................................1 Q 194377 Belt Plate, Specify Color...............................................2 194378 Top Panel, Specify Color...............................................2 194379 Bottom Panel, Specify Color. ._._.._____ ................. ..2 198514 Mounting Plate, Specify Color......................................2 194381 Shaft Mount, Specify Cola...........................................2 195244 23" Cable. Black ................... ___ .......... ......... ...._........ 4 196831 Presser Plate, Specify CWa......_._...............................2 212797 Boogie Board Hardware Package ............................1 100198 '/e" x 1 '/," BHCS w/Pin, SST.......................................4 113027 3/," x 1 3/," BHCS w/Pin, SST ...................................... 12 100290 3/,"x'/,"BHCS w/Pin Limited Thread, SST ...... ..... ._8 100351 3/r' Tee Nut, SST............................................................4 100353 3/r" Flange Nut w/Pin, SST ........................................... 12 121135 '/: O.D. x 2' Long Spring Pin, SST .............................2 127179 3/: O.D. x 3/: Bushing. SST.........................................8 128296 3/: lam Nut. SST...........................................................4 120302 Collar, SST....................................................................2 149200 Thrust Bearim...............................................................2 Specifications Post: See Play Booster` (PB) General Specifications. Mounting Plate: Weldment comprised or'/," (9,53 mm) thick HRPO sheet steel, and 2" (50,8 mm) O.D. x 1.50 " (38,1 mm) I.D. stainless steel housing. Finish: ProShields, colorspecified. (Oilite Bronze Bearing) 1.500" (38,1 mm) O.D. x 1.257' (31,92 mm) I.D. Shaft Mount: Weldment comprised of (6,35 mm) thick HRPO flat steel and 1" (25 mm) dismeter stainless steel shaft. Finish: ProShields, color specified. Belt Plate: Weldment comprised or 3/," (9,53 mm) thick HRPO sheet steel and'/," (6,35 mm) thick HRPO sheet steel. Finish: ProShieldr, color specified. Presser Plate: Fabricated from? GA. (. 179") (4,54 mm) thick HRPO sheet steel. Finish: ProShields, color specified. Cable Assembly: (Cable) Made of tightly woven polyester -wrapped, six -stranded galvanized -steel cable with a polypro- pylene core. (Cable Connectors) 6063-T6 alumi- num. Panels: Permalene`, color specified. Belt: .315" (8,00 mm) Thick mini rough top rubber belting with polyester fabric plys, black in color. Clamps: Cast Aluminum. Finish: ProShield', color specified. Fasteners: Primary fasteners shall be socketed and pinned tam- perproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Installation Time: Approx. 3 man hours Weight: 110 lbs. Concrete: Approx. 7.85 cu. ft. Fall Height: 24" (0,61 m) Installation Instructions 1) (Direct Bury) Dig footings to dimensions shown. 2) Attach shaft mounts to posts at height shown. Refer to the Shaft Mount Assembly Detail. 3) Slide mounting plate, thrust hearing, and collar onto shaft mount shaft. Lineup hole in collar with hole in shaft. Tap'/," O.D. x 2" long spring pin through collar and shaft. Refer to the Shaft Mount Assembly Detail. 4) Attach belt plates, presser plates and panels to belt. Refer to the Belt Plate Attachment Detail. 5) Insert 3/," O.D. x 3/," long bushings into belt plate tabs. Attach cables to belt plate tabs. Refer to the Boogie Board Attachment Detail. 6) Insert %" O.D. x 3/," long bushings into mounting plate holes. Attach cables to mounting plates. Refer to the Cable Attachment Detail. 7) With post plumb, pour concrete footing. Allow concrete footings to cure for a minimum of 72 hours before users are allowed to play on the structure. 8) Install '/," x %" drive rivets in 5" half clamps. Drill through hole in 5" half clamps and into 5" post with a'/," or"F' (only) drill bit. insert drive rivet in hole through clamp and into post. Hammer drive rivet pin in until flush with head. Refer to the Typical Offset Hanger Clamp Spec Sheet. 9) Install protective surfacing before users are allowed to play on the structure. ECO0100439Dxumm121278500re,,1Am1%%700. ReyIe heN Wksae. n.a 0 O A� �+ O y tin C 11 r `<{Y7 Sw m o s Q nx O ECO0100439Dxumm121278500re,,1Am1%%700. ReyIe heN Wksae. landscape structures, DETAIL SHAFT MOUNT ASSEMBLY (2) 1/1 O.D. x 2" ',Long Spring Pins Ja)m/Nub Post (2) Shaft Mounts (4)'/a' Tee Nuts o m (4) 1/1 x 1 ' BHCS w/Pin (2) Mounting (2 Plates Thrust Collars SAFETY NOTE hasaChoose al Heigh surfacing o at as that has a Cntiul Heigh Value of at lean ate 'JO 14UU3 height of the Highest AccessitNe F.N t Height of the adjacent equipment. tRef. comas ASTM F1481.) 212785a (4)'/a' O.D. x 3 Long Bushings DETAIL BELT PLATE ATTACHMENT NOTE: Attach belt with textured side up. 7!i (2) Top Panels (2) Presser Plates IMPORTANTI Do \ not use an Impact wrench to tighten BHCS w/pin. Do 0 not over torque fas- teners. Excessive m o tightening could e Plates cause panels to 0 crack. o o (12)1/8' FI6 Nuts w/Pin (2) Belt Plates (4) s/8' 0. D. x 3/," Long Bushings flayBoosterl 193176 • • •Board TAM 601 7TH STREET SOUTH, DELANO, MINNESOTA 653288605 888-574-4678 LSI Install Help 888438-65741 i DETAIL CABLE ATTACHMENT (2) Mounting 1/1 x %" BHCS 'in Limited DETAIL BOOGIE BOARD ATTACHIWNT n C 1 — � CT (4) 3/e" x'/e" BHCS w/Pin Limited Thread (4) Cables Sheet I landscape structures` PLAN VIEW/FOOTING LAYOUT --'j SAFETY NOTE r�igi,,-,c,),az,, ecpve ave'_materiel NatHaight Valuea aa9t aroMgpaNFellISO1�0�t I IuipnentASTM DETAIL 20157700 SUPPORT ARM ATTACHMENT (2) 6" Half Poet Clamps I SuDDortArm Support Arm I a Dods 1 I I - , "ll I'll V (4) •/a" T69 Nuts 4) Vile X 1/e, IHCS w/Pin Typical PlayBooster Post TDp 01 su ` Blender Assembly r� O C T „ —4 4 7 4 I 1 A ra m = ,.I iFinished Grade ■ Protective PlayBooster"', 201545 Blender T"' Spinner i Surfaclng Sheet I of 2 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574.4678 LSI Install Help 888-438-6574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 0 2012 by Landscape Structures All rights resened Document #20157700 kt i, landscape structures` Parts List Part# 100610-00 103327-01 155614-00 157092-00 160514-00 186027-00 195055-00 PlayBoosterl 201545 BlenderTMSpinner Description Qty. 14" x'/," Drive Rivet, AL/SST................................. 2 5" Half Clamp, Specify Color .................................. 2 Blender Assembly, Specify Color ............................ 1 Footer, (DB), Specify Color ...................................... " Spinner Post, (SM), Specify Color .......................... " Spinner UHM W Bushing .......................................... 4 Support Arm, Specify Color ..................................... I 160502-00 Spinner Hardware Package 100196-00 5/a" x'/s" BHCS w/Pin, SST .. 100351-00 5/," Tee Nuts, SST ................... 131849-00 5/„” it '/," BHCS w/Pin, SST 121348-00 4 -Hole (SM) Hardware Package ........................... 1 100266-00 '/," x 2 Y." Expansion Anchor .................................. 4 100322-00 'A" Standard Hex Nut, SST ...................................... 4 100363-00 '/," Flat Washer, SST ................................................. 4 DB - Direct Bury SM - Surface Mount s - Determined By Your Order SDecifications SupportArm: Weldment comprised oft.375"(60,33 mm) O.D. RS40 (.130"-.140"x3,30 man - 3,56 mm) wall galvanized steel tube, 2.750"(69,85 mm) O.D. 1018 steel, and'/," (6,35 thin) HRPO flat steel. Finish: ProShield", color specified. Blender Assy.: Weldment comprised of 1.900" O.D. RS20 (.090% .100" wall) galvanized steel tube, 10 Cra. (.135") HRPO steel, 2.750" O.D. 1018 steel and 1 %" steel ball. Fin- ish: ProShield, color specified. Bushing: Oil -filled UHMW PE. Footer: Weldment comprised of 2.375" O.D. RS40 (.130"- .140" Wall) galvanized steel tube, 12 Ga. (.105") HR flat steel and 1 7/0" steel ball. Finish: ProShield, color specified. Clamp: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: (DB) Approx. 2 man hours (SM) Approx. 1 '/, man hours Concrete Req.: (DB) Approx. 2.94 cu. fl. Min. Use Zone: 6'(1,83 m) minimum use zone Weight: (DB) 103 lbs. (SM) 101 lbs. Fall Height: 75" (1,90 m) Installation Instructions 1) (Direct Bury) Dig footings as shown. Refer to the Plan Yew Foot- ing Layout and Footer Attachment Detail. 2) Attach support arm to posts at height shown, using 5" half clamps, 1/1" x 7/s" BHCS w/pin and 5/s" tee nuts. Refer to the Support Arm At- tachment Detail. 3) Place a bushing on each side of the footer post's 1 '/," bail, as shown. Insert footer post with bushings into Blender assembly. Align holes in bushings with holes in housing. When holes are aligned, insert'/,6" x '/_" BHCS w/pin. Refer to the Blender Assembly Detail. NOTE: Use the slot in the bottom of the bushing to align holes. 4) Place a bushing on each side of the Blender assemblies 1 '/w' ball, as shown. insert Blender assembly with bushings into upper spinner mount. Align holes in bushings with holes in housing. When holes are aligned, insert'/„” x '/2' BHCS w/pin. Refer to the Blender As- sembly Detail. NOTE: Use the slot in the bottom of the bushing to align holes. 5) (Direct Bury) Place a level on the footer gusset, when gusset is plumb, pour concrete footing. Allow concrete footing to cure a minimum of 72 hours before users are allowed to play on structure. NOTE: Blender assembly will have to be propped in position, until concrete has cured (Surface Mount) Drill'/," x 3" deep holes through spinner post plate using hammer drill and'/," masonry bit. Tap expansion anchors into drilled holes. Fasten spinner post to expansion anchors using '/," standard hex nuts with '/," Bat washers. 6) Install'/," x %" drive rivets in 5" half clamps. Drill through hole in half clamps and into 5" post with a I/," or "F" (only) drill bit, insert rivet in hole and hammer rivet pin in until it is flush with head. 7) Install protective surfacing before users are allowed to play on the structure. JSNi UOm100091 �tN15Tx10,eybces 18757Q0. FtVtac>5s"pp"na . SAFETY NOTE Choose a xotem a ew,aorg material -1 7 has Crifi o Highest WWe si at least Rte /U/7C height of Rho M9ries1 Accesslt ( PaNFall ikgltt o/ Rta eQerent eW^pttetrt. IRer. ASTM F198I) landscape 172570a structures NOTE: Sufficient protective DETAIL surfacing must cover hard- BLENDERASSEMBLY ware to satisfy fall height re- quirements. DETAIL SURFACE MOUNT oBushin le In Spinner Post ds to (4)'/;' Standard h hole Support Hex Nut w/ /,' Flat rm be- Aral Washer — ing. (4)'/i' x 2 a/;' (2) 5/j;' x'/", Expansion BHCS w/Pin Anchor JI Concrete Slaty - ings Rock Crushed the bottom of the bush- ing to align hole in bush- ing with hole in support Blender N arm. Assembly o DETAIL on c,-:,,, n FOOTER ATTACHMENT '—t -4 ::;C r _ Blender < S a0= Assembly y cn ": Loose Fill -� Gusset (For Leveling). a s � a- �1 Subgrede _ Footer:o Concrete Crushed Rock 18` 460 3 201545 Blendee"Spinner 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888.5744678 LSI Install Help 888438-6574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 9/& landscape structures° mooseapral Height aValueto malMal that has a Critical ght of the Highest Value of at leant at IS014001 "Heigh ofthe acjsmnt acssmen01(Re, SFn, I I F11BL) ce.unea 19496900 DETAIL E?OD STEP Protective PlavBooster® 193170 LolliLadder Surfacing rstings 1 /". /Pin C 2013 ey Laxscaps Structures no nghts reserved Document #19496900 1h landscape structures, Parts List Part# Description Qty. 100610-00 It, x'/," Drive Rivet, AL/SST...................................... 4 105327-01 5" Half Clamp, Specify Color .. . ...................................4 182262-00 Rung Cap, Black.............................................................7 Q 190760-00 LolliLadder, Specify Color ............................................ 1 154461-00 E -Pod, Specify Color......................................................2 156806-00 Pod Casting, Specify Color...........................................2 195445-00 LolliLadder Hardware Package................................1 100196-00 5/," x '/t" BHCS w/Pin, SST .......................................... 8 100201-00 5/t" x 1 5/2" BHCS w/Pin, SST.......................................7 100351-00 %" Tee Nut w/Pin, SST..................................................8 156968-00 Pod Hardware Package ......... .....................................2 100198-00 5/," x 1 '/e" BHCS w/Pin, SST ....................................... 8 100610-00 '/," x'/," Drive Rivet, AL/SST......................................2 Specifications LABII -adder. Weldment comprised of '/," (6,35 mm) HRPO flat steel, 2.375" (60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm -3,55 mm) wall galvanized steel tubing, and 1.315" (33,40 mm) O.D. RS20 (.080"-.090") (2,03 mm -2,29 mm) wall galvanized tubing. Finish: ProShield", color specified.. Finish: ProShield, color specified. Rung Cap: EPDM, black in color. E -Pod: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Pod Casting: Fabricated from sand cast alloy 356 in accordance with ASTM B26. Finish: ProShield", color specified. Half Clamp: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 2'/4 man hours Weight: 81 lbs. Max. Fall Height: 69" -72" (1,75 m-1,82 m) PlayBooster' 193170 LolliLadderr' Installation Instructions 1) (Direct Bun) Refer to the Site Plan for footing locations. 2) Attach rung caps to LolliLadder. Refer to Detail. NOTE: Make sure pin is inserted into small hole in back of rung cap beforefastener is tightened. 3) Attach LolliLadder to posts at height shown. Refer to LolliLadder Attachment Detail. 4) Attach a -pods and pod castings to post as shown, using'/r" x I '/r" BRCS w/pin. Refer to E -Pod Step Detail. 5) Drill through hole in pod casting and into post with a '/," or "F" (only) drill bit. Insert'/," x'/," rivet in hole and hammer rivet pin in until it is flush with head. 6) Install '/," x'/t" drive rivets in all 5" half clamps. Drill through hole in 5" half clamps and into 5" post with a'/," or "F" (only) drill bit, insert drive rivet in hole through clamp and into post. Hammer drive rivet pin in until flush with head. Refer to the Typical Offset Hanger Clamp Spec Sheet. 7) Install protective surfacing before users are allowed to play on the structure. N o_ O_ �n U O 1 C")� t `� 0� t O Q :A t,D r vD � SAFETY NOTE J Choose a protective aunearg metenal roar hea a Cntiral Height Value of et least the height of the Highest AccassiEle PaNFall ®'®III Cer'IfIeG FtrM heefae tegWpmeMtRe ASTM landscape structures° 17959500 Infill poster' 179594 Vibe° Roof Sheet 1 of 2 Shoaures An aghts reserved Document #17959600 (7) 31, 11 X 7/e 1 BHCS w/Pin w/ a/a" SAE Flat Washers Vibe Roof i d Tie 5800 - o o o --t c�-G t pa.•,••.°, O` 32. 'ern rn Faa®®' df Top Of Post ® I n i (8) a/e. X t a/a. (2) t/aw X s/a Typical/ y BH CS w/Pin Drive Rivets PlayBooster Bottom Of Post Clamp poster' 179594 Vibe° Roof Sheet 1 of 2 Shoaures An aghts reserved Document #17959600 jt�L landscape structures, J1SPEOS IM17 59600. P65 Parts List PaI(F Description Qty. 100610-00 '/1" x'/r" Drive Rivet, AL/SST.....................................2 1/." x 1 '/e" BHCS w/Pin, SST......................................8 177021-00 Vibe Roof Roto, Specify Color....................................1 178724-00 Infill Panel, Specify Color............................................1 uct installation/specifications). 178725-00 Roof Clamp, Specify Color...........................................2 Weight: 179611-00 Vibe Roof Hardware Package ................................... l 100196-00 1/g" x 7/8" BHCS w/Pin, SST...... ................................... 7 100198-00 1/." x 1 '/e" BHCS w/Pin, SST......................................8 100365-00 1/e" SAE Fiat Washer, SST............................................7 Specifications Infill Panel: Made from 12 GA. (105") (3,18 mm) thick HRPO steel sheet zinc plated Finish: ProShielP, color speci- fied. Roof: Rotationally molded from U.V. stabilized linear low PlayBooster179594 VibeO Roof Installation Instructions 1) Fasten infill panel to roof, using'/s" x 7/a" BHCS w/pin and %" SAE flat washers. 2) Attach roof to posts at dimension shown, using roof clamps and'/s" x 1'/r" BHCS w/pin. 3) Using the predrilled '/." holes in roof clamps as a guide, drill 1/4" holes into posts. Insert'/," x %" drive rivets into drilled holes and tap pin in until it is flush with rivet head. 4) Install protective surfacing before users are allowed to play on the structure. density polyethylene, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned �-+ tamperproofin design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific prod- m uct installation/specifications). Installation Time: Approx. 2 man hours per roof Weight: 81 lbs. PlayBooster179594 VibeO Roof Installation Instructions 1) Fasten infill panel to roof, using'/s" x 7/a" BHCS w/pin and %" SAE flat washers. 2) Attach roof to posts at dimension shown, using roof clamps and'/s" x 1'/r" BHCS w/pin. 3) Using the predrilled '/." holes in roof clamps as a guide, drill 1/4" holes into posts. Insert'/," x %" drive rivets into drilled holes and tap pin in until it is flush with rivet head. 4) Install protective surfacing before users are allowed to play on the structure. N G_ e!1 t- �-+ n-< m 2f IM— a (� D to lO j & landscape structures° DETAIL 1 1 1 C E P T I F I E 0 SAFETY NOTE Choose a prolective euRating material that hes a Critical Height Value of at least the hi of the Highest Accessi Ne PaNFall HNghtoftheacjacernl equipment (Ref ASTM F148).) 179596a DETAIL Vibe Roof BACK TO BACK ROOFS 4.1no2 i NOTE: When attaching two roofs back to back, slide roofs onto posts, fasten up- per roof to posts at dimen- sion shown, then slide lower roof up to upper roof and fasten to posts. Vibe Roof N IC2) 71 O Cl -1 C-,-< =in a` <nT > M J Typical � PlayBooster Post 1 PlayBooster' 179594 •'©Roof Sheet 2 of tof 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8605 888-574-4678 LSI Install Help 888-438-6574 LSI Direct 763-972-5200 lint. FAX (763) 972-3185 C 2011 by Landscape Structures All rights reservec! Document #179596CM jb, landscape structures Typical PlayBooster Post of Panel Top of Deck (2)Typical Offset Hanger Clamp/ ` Assemblies XI x 2 t/4" w/Pin SAFETY NOTE Choose a preleetive surfaarg material that hes a Critical Height Value o/ et least the �SD�A oOl dhm height M the Highest Accessible P.NFell `T Helghtd Ne a§acenlegWpnenl(Ref ASTM ® F1487.) Carsllletl 17787300 ENTRANCE SECTION ATTACHMENT Entrance Section E E 0 0 m 11 a/, • 289 LL 7Deck a /Entrance Section 4071 Rail (2) Spacer Tubes (4) a/e " x 7/," BHCS w/Pin w/ 34" Flat Washers PlayBooster° 124863 SlideWi (2)Typical Offset Hanger Clamp Assemblies NOTE: If SlideWinder is off a96" deck,182' steel posts are required with a 44" bury. "z10 z C-) o C-) Cr, r r— 'i j & landscape structures° Typical Section NOTE: Elbow sections will be marked (LH) for left hand and (RH) for right hand. Typical Section DETAIL - SLIDE SECTION NOTE: Fasten top of slide section with pockets to bot- tom of slide section without pockets. NOTE: Refer to your plan drawing for location of mid -supports and their footing depth (DB). Typical Section (Underside) (2) 3/d' x 1 "/,a" BHCS w/Pin w/ 3/;' Flat Washers (3) "1 x 1 "1 BHCS w/Pin w/ 3/8' Flat Washers DETAIL TYPICAL MID -SUPPORT (48"-96" SLIDES ONLY) BOTTOM VIEW G� Typical Mid -Support 154947a0 Typica�ection UndeFeMe) C-) 1>:�­4 n —1-1 C-) Q, r �� �m DT rn S 0 kA :P", to ii.o DO NOT sandwich support between sec- tions. Mount on out- side. (3) N." x 1 3/1 BHCS w/Pin Emo 124863 • • 601 7TH STREET SOUTH, -8605 MINNESOTA 55328-8605 888-5744678 LSI Install Help 888438-6574 LSI Direct 763-972-5200 Int. FAX (763(972-3185 S & landscape structures® Top Of Sliding 0 N DETAIL DIRECT BURY / EXIT Crushed Rock SAFETY NOTE Choose a protective sudadng material Mat has a Critical Heigh Value of at least Me height or the Highest Accessible PaNFall Heighafihe agacent equipment (Ref ASTM F14BZ) 128348b0 DETAIL DIRECT BURY/ MID -SUPPORTS NOTE: Attach bolts in the center of the footer slots to allow for expansion and contraction. Snug bolts down only, do not overtighten! NOTE: Thickness of uni- tary protective surfacing depends upon the slide deck height. (2)1/2' x 2'/;' Expansion Q�-° Anchors w/ 1/,' Flat Washers & 1/2' Standard Hex Nuts DETAIL RFACEMOUNT / EXIT SECTION ------- Exit Section cD—(2)'/;' Flange Nuts w/Pin Leg Base Unitary Protective Surfacing e �Conc Slab m -- --in rushed - nags Mid Support - Exit Loose Fill ,-. o Section Protective.,) (2) Surfacing (2) 3/9' Flat Washers 3/p" 1&" (2) 3/;' Flat Washers E (2) Rubber Bushings= a a E .ACO Concrete Slab - 4 2 1/ - (2)'/;' Flat Washers - (2)3/;"x 1'/q" Subgrade a.:-,. o0 a - = BHCS w/Pin > N o Limited Thread I� Bolts Footinete Crushed 12" Subgrade Rock 300 Exit Footer a a DETAIL Concrete Footing SURFACE MOUNT /MID -SUPPORTS 300 Threaded -1, Rod, IA -Support NOTE: Attach bolts in the center of the footer slots to allow for expansion and contraction. Snug bolts down only, do not overtighten! NOTE: Thickness of uni- tary protective surfacing depends upon the slide deck height. (2)1/2' x 2'/;' Expansion Q�-° Anchors w/ 1/,' Flat Washers & 1/2' Standard Hex Nuts DETAIL RFACEMOUNT / EXIT SECTION ------- Exit Section cD—(2)'/;' Flange Nuts w/Pin Leg Base Unitary Protective Surfacing e �Conc Slab m -- --in rushed - nags O 2 x 4 NOTE: Sufficient protec- Expansion tive surfacing must cover Anchors &'/2" hardware to satisfy fall Flat Washers height requirements. w/ /,' Standard Crushed Hex Nuts Rock PlayBoosterO 124863 SlideWinder2 Details Sheet 2of2 0201) by Lamisape swctures. All nghta reserved. Document#17787300 ` - - (2)'/;' Flat Washers Rubber Bushings o N Support (2) (2) 3/9' Flat Washers 3/p" 1&" (2) x 1 BHCS w/Pin Limited Thread Bolts Concrete Slab - 2 1/ O 2 x 4 NOTE: Sufficient protec- Expansion tive surfacing must cover Anchors &'/2" hardware to satisfy fall Flat Washers height requirements. w/ /,' Standard Crushed Hex Nuts Rock PlayBoosterO 124863 SlideWinder2 Details Sheet 2of2 0201) by Lamisape swctures. All nghta reserved. Document#17787300 k& landscape structures, JASPECSN 77\17787300.185 Parts List PlayBooster` 124863 SlideWindei-2, 3r'-9611 Part# Description Qty. 124867-00 Right Elbow Section, Specify Color ..... ...... ................. * 124868-00 Left Elbow Section, Specify Color ................................ Mid -Support: 125655-00 Straight Section (15'/4" Long), Specify Color ............. .100") galvanized steel tubing and'/�s' x I zinc plated steel strap. Finish: Pro3hield, color specified. 124864-00 Straight Section (30'/2" Long), Specify Color ............. 100583-00 40 7/16" Rail, Specify Color ............................................. 1 105327-01 5" Half Clamp, Specify Color ........................................ 2 113729-00 Offset Hanger Clamp, Specify Color ............................. 2 100610-00 '/4" x %" Drive Rivet, AL/SST....................................... 2 125562-00 Support Base (SM), Sppecify Color ................................ Cast aluminum. Finish: ProShield, color specified 128434-00 66" Mid -Support (DB), Specify Color .......................... • 128077-00 82" Mid -Support (DB), Specify Color .......................... * 128078-00 106" Mid -Support (DB), Specify Color ........................ 128079-00 20'/4' Mid -Support (SM), Specify Color ..................... 128080-00 29" Mid -Support (SM), Specify Color .......................... 128081-00 37 4a" Mid -Support (SM), Specify Color ..................... 128082-00 45'/4' Mid -Support (SM), Specify Color .....................' 128261-00 Exit Footer (DB), Specify Color .................................... 1 128262-00 Exit Footer (SM), Specify Color .................................... 1 124876-00 Entrance Section, Specify Color .................................... 1 124877-00 Exit Section, Specify Color ............................................ 1 132443-00 Spacer Tube, Specify Color ............................................ 2 121371-00 Eat rance/Deck Mounting Hardware Package ......... 1 100196-00 '/e' x %" BHCS w/Pin, SST...........................................4 100362-00 '/:' Flat Washer, SST.......................................................4 154942-00 SlideWinder Section Hardware Package .................. • 100362-00 3/e" Flat Washer, SST ....................................................... * 113027-00 34" x 1 14" BHCS w/Pin, SST ........................................ 123224-00 3/s" x 1 11/,," BHCS w/Pin, SST ...................................... 124342-00 Rail Hardware Package ................................................ 1 100198-00 1/#" x I '/s" BHCS w/Pin, SST ........................................ 4 100203-00 3/"" x 2'/4" BHCS w/Pin, SST ........................................ 2 100351-00 3/8" Tee Nut, SST.............................................................. 4 125670-00 Mid -Support Hardware Package (SM) .....................' 100266-00 1/2" x 2 /4" Expansion Anchor ........................................ 100322-00 '/2" Standard Hex Nut, SST ............................................ 100353-00 3/a" Flange Nut w/Pin, SST ............................................. * 100363-00 '/2" Flat Washer, SST ....................................................... * 115813-00 3/s" x 1 '/2" Threaded Rod, SST ...................................... * 128373-00 Exit Support Hardware Package (DB) ...................... 1 100292-00 3/"" x 1 /a' BHCS w/Pin Limited Thread Bolt, SST .... 2 100362-00 3/"" Flat Washer. SST.......................................................4 111442-00 Rubber Hushing............................................................... 2 128343-00 Exit Su�port Hardware Package (SM) ...................... 1 100266-00 '/2" z 2 /4" Expansion Anchor ........................................ 2 100292-00 3/e" x 1 '/4" BHCS w/Pia Limited Thread Bolt, SST.... 2 100322-00 1/," Standard Hex Nut, SST ............................................ 2 100362-00 3/i' Flat Washer, SST.......................................................4 100363-00 1/2" Flat Washer, SST.......................................................2 111442-00 Rubber Bushing...............................................................2 DB = Direct Bury SM = Surface Mount • = Quantity Varies Per Deck Height Specifications Slide Sections: Rotationally molded from U.V. stabilized linear low Installation Time: Concrete Req.: Weight: density polyethylene, color specified. Rail: 1 '/" O.D. 6005-T5 alumm inuextrusion with S4,1. walls. Finish: ProShielda, color specified. Mid -Support: Weldment comprised of 1.900" O.D. RS -20 (.090" - '14" .100") galvanized steel tubing and'/�s' x I zinc plated steel strap. Finish: Pro3hield, color specified. Support Base (51177: Weldment comprised of 1.660" O.D. RS -20 (.085" - .095") alvanized steel tubing and 14" x 3" x 8"mount- ing plaie. Finish: ProShield, color specified Spacer Tube: Fabricated from 1.3125 O.D. x 16 Ga. (.065) steel tub- ing. Finish: ProShield, color specified. Exit Footer: Weldment comprised of 2.375" O.D. RS -20 (.095" - .105").galvanized_ steel tubing and I/" x 3" x 7 '/i' mounting plate. Finish: ProSiueld, coior specified. Offset Hanger Clamp Assy.: Cast aluminum. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tamperproof indesign, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Concrete Req.: Weight: 32" - 48" Approx. 3 man hours 56" - 72" Approx. 4 man hours 96" Approx. 5 man hours 30" Depth - Approx. 1.3 cu. ft. 33344g" DDee�pth - Approx. 1.5 cu. ft. 32�� - 134 lbs Brox. 1.8 cu. ft. 40 - 146 lbs. 48" - 172 Its. Fail Height: 64" - 18947 lbs. 72" - 247 lbs. 96" - 265 lbs. Deck Height Installation Instructions 1) Refer to your plan drawing for location of footings and direction of SlideWinder sections. 2) (Direct Bury) Dig footing holes spaced as shown, depending upon slide. Refer to the Direct Bury Exit Section and Direct Bury Mid - Support Details. 3) Place 40'/14" rail in entrance section, place spacer tubes over each end of the 40 7/,s" rail, attach offset hanger clamps using 1/t" x 2 1/4" BHCS w/Pin. 4) Fasten SlideWinder sections together loosely starting in the middle and working your way to the outside of each section, using 3/s" x 1 3/s" BHCS w/Pin with'/a' flat washers on the 3 inside holes and %" x 1 "/,s' BHCS w/pin with 3/a' flat washers on the 2 outside holes. When all bolts are started, pull the tops flush with each other and tighten. The left elbow section reads (LH) and the right elbow section reads (RH). Attach entrance and exit section last. Refer to the Typical Slide See - tion Detail. 5) (Direct Bury) If required attach mid -supports, refer to your plan drawing for locations. Attach mid -supports to slide using 3/a' x 1 3/a' BHCS w/Pin. Refer to the Typical Mid -Support Detail. (Surface Mount) If required attach mid -supports, refer to your plan drawing for locations. Assemble mid-suplports by placing support base inside mid -support and attach using /a" x 1 '/r" threaded rod and %" flange nuts w/pin. Refer to the Surface Mount/Mid-Support Detail. Attach mid -supports to slide using %11 x 1 3/#" BHCS w/Pin. Refer to the Typical Mid -Support Detail. 6) Attach exit footer to base of slide using 3/a' x 1 1/4" BHCS w/Pin limited thread bolts, 3/#" flat washers, rubber bushings and 3/a' flat washers. NOTE: Attach bolts in the center of the slots to allow for expansion and contraction. Snug bolts down only, do not overtighten. See Direct Bury/Exit Section Detail. 7) With SlideWinder fully assembled, attach entrance section to the face of the deck using 3/s" x 1/s" BHCS w/Pin and %1121 washers. 8) Attach offset hanger clamps to posts us9 5" half Tamps, 3/s" x I '/#" BHCS w/Pin and 3/a' tee nuts. Refer tTypMgl Offsat„9 tj;- ger Clamp Spec Sheet. 9) (Direct Bury) With supports plumb p('� cre footin Ilow concrete footings to cure for aminimum- f ho�befor us rs are allowed to play on the structure. �. �}� (Surface Mount) Mark anchor bolt locaT�icrUbnc to slMugh holes in anchor plates. Drill'/r" x 3"d> "itblesv5 markkt��tt� con- crete using ahammer drill and'/r" mast>163, . Tapbl2" x 2'ysl' pan- sion anchors into drilled holes and fastt;using V"'sjtandard hex nuts with'/2" flat washers. tA 10) Install protective surfacing before users are allowed to play on the structure. Ecu#54291 nxume"1#17787300rePl #154%700.Addedspacertub mPans List S & landscape structurev Typical PlayBooster Mainstructure Post F , , I I I , I , I I ' I ' I ' I ' I , I , I I I I I I I I I I I ,I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I I Cloudburst Slide Hood SAFEN NOTE lighmCeoose a prolective surtatilg male'ial lhal /� has a Critical Heigh Value of al Ieasl NB IS0 14001 IT H4BIJ Certified 14468400 ELEVATION 2g" 740 a Cloudburst Slide Hood Cloudburst Triple edwav Slide „ „ II „ „ „ II (2) Mid -Supports Cloudburst Triple Bedway Slide Surfacing rst° Slide Finished Szrade Exit Supports Yqa H�� MY�9 C"70 Sheet 1 of 2 Document#20341000 j L ^ 161089a landscape structuresFl DETAIL CLOUDBURST SLIDE HOOD (2) 1'/,s' O D x 1 11/,s" ATTACHMENT ; (4) Typical Offset Hanger (2)'/;' x 2 1/4" Rail Spacers Clamp Assemblies BHCS w/pin - 57 13/,;' Pipebolt Cloudburst Slide Top Hood Clamp (2)'/s' x 31/," BHCS w/Pin � � ', w/ 3/," Fla Washers ' Top 01 ------------- --- Clamp 90' Tn-Deck SLIDE HOOD - HANDLE DETAIL ----- Top 0 Deck (2) Spacer Tubes Handle PLAN VIEW/FOOTING LAYOUT 118 b^ 11" Refer To Your Site Plan 3013 280 For Minmum Use Zone 112'/;' 2864 56" 1420 Typical Concrete Footing _ ser Long Tri -Deck 0 o �! 64"-72" D b' -I —11 ..� Deck Height -iC7 C� v� PlayBoosterl�' P 2014 by Lenbccape SV lt,rts All ngntsre ,e d j U (. landscape structures" DETAIL MID -SUPPORT ATTACHMENT SAFETY NOTE Choose a protective sWa.rg mato nal that has a Critical Height Value of at least the height of the Highest Accessible PaNFall Height of Hae aClacer t equipneM (Ret. ASTM F1487) 1446800 DETAIL DECK CONNECTION Cloudburst Triple Bedway Slide Cloudburst (4) 3/8' Flat Washers Triple Bedway Slide (4) Rubber Bushings Dock (4)3/;' Flat Washer N C' o Limited Thread (2) Mid -Supports BHCS w/Pin Loose Fill = , n� I a% r Protective 3/9 x 1/� T Surfacing.,_ BHCSw/Pin f1T Mal ' •f Z w/3/;'Flat O Washers - o Ln Subgrade _ _ � � `,$ rn _ DETAIL Typical ,, N4 Cloudburst EXIT SUPPORT ATTACHMENT Concrete Triple Bedway Footing Slide Top of Crushed Sliding Surface Rock 12" 300C DETAIL (6)7FlatWashers (6) Y SURFACE MOUNT (6)Expansion (10)'/;' x 2 a!;' Anchors (6) w/'/," Flat Washers BHCS w/Pin (5) Supports V." &!z"StandardHex Limited Loose Fill Nuts Thread ;� .,?:^"-.'.-�, c,!:.:- * �k..,,�- ::=•C,i': • Protective Surfacing - - - Subgrade _ Concrete - _ - (3) Exit Supports o— N N NOTE: Sufficient protec- a'.: a :- Crushed tive surfacing must cover Typica Rockhardware to satisfy fall Concrete Footing height requirements. Bottom Of Exit Support When 12" Crushed Attaching Slide To A 72" Deck 300 Rock PlayBooster' 144414 Cloudburst° Slide sheet 2 of 2 02014 by Landscape Structures All nghts reserved Document #20341000 k1 -1 - landscape structures' Parts List PlayBoosterl 144414 Cloudburst° Slide Part# Description Qty. 142545-00 Cloudburst Triple Bedway Slide, Specify Color.... 1 142546-00 Cloudburst Slide Hood, Specify Color .................... 1 105327-01 5" Half Clamp, Specify Color .................................. 4 113729-00 Offset Hanger Clamp, Specify Color ....................... 4 144474-00 57 "/,." Aluminum Pipebolt, Specify Color........... 1 113468-00 Spacer Tube, Specify Color ...................................... 2 150941-00 Exit Support (DB), Specify Color ............................ 3 145072-00 Mid-Suppon 64" Deck (DB), Specify Color.......... 2 145073-00 Mid -Support 72" Deck (DB), Specify Color.......... 2 151033-00 Exit Support 64" Deck (SM), Specify Color.......... 3 151297-00 Exit Support 72" Deck (SM), Specify Color.......... 3 145074-00 Mid -Support 64" Deck (SM), Specify Color.......... 2 145075-00 Mid -Support 72" Deck (SM), Specify Color.......... 2 132443-00 1 1/„” O.D. x 1 "/," Rail Spacer, Specify Color... 2 100610-00/," x a/, Drive Rivet, Al/SST................................. 4 144685-00 Slide Hardware Package ........................................ 1 100196-00 %" x 7/," BHCS w/Pin, SST ..................................... 4 100292-00 '/1" x 1 1/4" BHCS w/Pin Ltd. Thread Bolt, SST ... 10 100362-00 %' Flat Washer, SST ................................................ 24 111442-00 Rubber Bashing........................................................ 10 106577-00 Hood Hardware Package ........................................ 1 100198-00 1/." x l '/," BHCS w/Pin, SST .................................. 8 100200-00 34" z 3'/1" BHCS w/Pin, SST .................................. 2 100203-00 1/." x 2 'Q" BHCS w/Pin, SST .................................. 2 100351-00 14" Tee Nut, SST ........................................................ 8 100362-00 1/," Flat Washer, SST ................................................. 2 100610-00 '/," x 14" Drive Rivet, AL/SST................................. 4 111392-00 2 -Holt (SM) Hardware Package ........................... 5 100266-00 1/3" z 2 '/4" Expansion Anchor ................................. 10 100322-00 '/," Standard Hex Nut, SST ..................................... 10 100363-00 '/," Flat Washer, SST ................................................ 10 DB - Direct Bury SM - Surface Mount Specifications Slide: Rotationally molded from U.V. stabilized linear low- density polyethylene, color specified. Exit Support: Weldment comprised of 2.375" O.D. RS20 (.095" - .105') galvanized steel tubing and '/," x 3" mounting plate. Finish: ProShield", color specified. Mid -Support: Weldment comprised of 1.660" O.D. RS20 (.085" - .095") galvanized steel tubing and'/," x 3" mounting plate. Finish: ProShield, color specified. Hood: Rotationally molded from U.V. stabilized linear low- density polyethylene, color specified. Rall: Extruded from 1.125" O.D. x.312" W. 6005-T5 alu- minum. Finish: ProShield, color specified. Rail Spacer: Fabricated from 1.3125" O.D. x 16 Ga. (.065") steel tubing. Finish: ProShield, color specified. Spacer Tube: Made from 6061-T6 aluminum 7/," O.D. x 1 Finish: ProShield, color specified. Offset Hanger Clamp Assembly: Cast aluminum Finish: Prostield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design. stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Concrete Req.: Area Req.: Weight: Fall Height: (DB) - 3 V. man hours (SM) - 2 '/, man hours 6.5 cu. R. Refer to Site Plan (DB) - 475 lbs. (SM) - 455 lbs. Deck Height Installation Instructions 1) (Direct Bury) Dig footings spaced as shown. 2) Insert 57 1/,e" pipe bolt through top of hood. Place I'/„” O.D. x I long rail spacer tube on each end of the 57 111," pipebolt. Attach offset hanger clamps to ends of pipe bolt using'/." is 2'/," BHCS w/Pin. Fasten offset hanger clamps to bottom of hood using'/s" x 3 '/r" BHCS w/Pin with'/," flat washers through offset hanger clamp and spacer tubes and into threaded inserts in hood. Attach offset hanger clamps to posts at height shown using 5" half clamps with'/," x I Y." BHCS w/Pin and 3/," tee nuts. Refer to the Cloudburst Slide Hood Attach- ment Detail. 3) Attach exit and mid -supports to slide using 1/," x 1 '/," BHCS w/Pin limited thread bolts, 1/," flat washers and rubber bushings. Refer to the Support Attachment Details. NOTE: Attach bipl/c in the center of the slots to allow for expansion and contractiarrFaag baits down only, do not overtighten! — eJ n O 1 4) Attach slide to the face of the deck using 5; 1SIff" Bpi S w/Pia,with 34" flat washers. Refer to the Deck Conn FiinKDetail. ON 1 5) Install'/," x'/," drive rivets in all 5" halfRefeerr to the t Hanger Clamp Spec Sheet. tT1 3 f� 6) (Direct Bury) With supports plumb pour;i;6 f00ings. A W concrete footings to cure for a minimum Qr72 hour�*fore users are allowed to play on the structure. r �0 (Surface Mount) Mark anchor bolt locations on concrete slab through holes in anchor plates and remove wave slide. Drill'/," x 3" deep holes on marks into concrete using a hammer drill and '/r" masonry bit. Tap expansion anchors into drilled holes. Reposition slide and reattach to the face of the deck following step 4. Fasten supports to expansion anchors using '/2" standard hex nuts with'/." flat washers. 7) Install protective surfacing before users are allowed to play on the structure. &oganel,4 D wai XN134IBOBwytxwr161MW.L gth 72"DBmibsup 9/1q landscape structures• DETAIL LEFT CURVED CONFIGURATION I SAF ETY NOTE - surfal Choose a i r l Helve sValw melariel Nat has a Critical Height V ixe si la leant the ISO 14001 HeeghtaNaa4a�ight of the a� �aea 1(Rd..A M Ce li'letl F1487 19698600 ;oostW 189313 Rushwinder Slide Sheet 1 of 3 0 2013 oy Laoascape 9rucmres. All rights rasarveo. Document #19698600 landscape &-+ra sill fir'l gh ISOs' RnEEFERM, Finished Grade PlavBooster" 189313 C 2013 by Lanbsaape Stmctures. All rights reserved )5'1 amp (4) Tee SAFETY NOTE Choose a pGedive surtdufg malenal Nal has a Cn[cal Height Value M et least the height of the Highest Accessible PaNFall Heghtolthe argacentequipment. (RM. ASTM DETAIL CROSSOVER ATTACHMENT (4) 3/8" x 7/all BHCS w/Pin DETAIL RUNG CAP ATTACHMENT Ladder NOTE: Make sure pin is inserted into small hole in back of rung cap before fastener is tightened. Slide 196986a Crossover Rung ps rn Y> Pdf;S w/Pin A& landscape structures SAFETY NOTE CAroase a protective aurfaung material Nat Ma a Ctl Heigh Value o1 lean the Might M the ha Highest Accessible Ref, F1487) 196986b (Ref ASTM FH87J 196986b DETAIL SLIDE HOOD TO CROSSOVER ATTACHMENT Ladder PlayBoostero 189313•Slide Sheet 2 of 3 601 7TH STREET SOUTH, DELANO, MINNESOTA 553288605 888-574-4678 LSI Install Help 888438-6574 LSI Direct 763-972-5200 hL FAX (763) 972-3185 Document #19698601 landscape structures' SAFETY NOTE Choose a prolaNve suRaang metenal Nat has a CdOcal Height Value of al least the IS014001 He'ghto Heade a sey igne t,H aM Certifiied F14BIJ DETAIL TYPICAL SLIDE SECTION (2) %" X 1 11/1e" BHCS w/Pin w/ 3/a" Flat Washers (3) 3/.' x 1 3/s' BHCS w/Pin w/ 3/;' Flat Washers DETAIL TYPICAL SUPPORT BOTTOM VIEW Typical Section / (Underside) PlayBoostero 189313 Rushwinder Slide 02013 Ey Lende.,>e SWMres. NI rights reserved. 154947a0 A& landscape structures r Top Of Sliding Surface Loose Fill Protective ' Surfacing ' DETAIL EXIT SECTION DIRECT BURY 1 I 1 crr+1(riEo SAFETY NOTE Choose a protective surfacing materiel urat has a Chi l Height Value of at least the height of the Highest Accessible PaNPall Height of the adacent a uipmeht,(Ret. ASTM F14d]) 189366b 305 NOTE: Attach bolts in the center of the footer slots to allow for expansion and con- traction. Snug bolts down only, do not overtighten! 189313 Rushwinder Slide N] Sheet 3 of 3 0 2013 by Landscape Swowre: An nghis reserved. Document #19698600 N O DC7 p 6 i Section DETAMIQ aN SUPPORTS/VERTI LADDER DIRECTBLM n _ (2MIupports & 305 NOTE: Attach bolts in the center of the footer slots to allow for expansion and con- traction. Snug bolts down only, do not overtighten! 189313 Rushwinder Slide N] Sheet 3 of 3 0 2013 by Landscape Swowre: An nghis reserved. Document #19698600 Loose FIII 'fi Exit Protective; Section Surfacing -1. _• _; _;:_,. Subgrade 8 -•:-' a- (2) 3/,-' Flat Washers _ (2) Rubber Bushings 9 '`• - •- _-_-rcrc•' (2)3/;' Flat Washers .- <° - - BHCSw/Pin Concrete Limited Thread _-`�'�'i'• - �- Bolts- Crushed - - Subgrade Rock 12" _ a•.:; a:;,: Exit Footer Concrete Crushed Rock 305 NOTE: Attach bolts in the center of the footer slots to allow for expansion and con- traction. Snug bolts down only, do not overtighten! 189313 Rushwinder Slide N] Sheet 3 of 3 0 2013 by Landscape Swowre: An nghis reserved. Document #19698600 ih PlayBoosterl 189313 Rushwinder Slide U v Hand Grip: Weldment comprised of 1.315" (33,4 mm) O.D. RS20 landscape (.080"-.090") (2,03 mm -2,28 nun) wall galvanized structures' steel tubing and 7 GA. (.179") (4,54 mm) HRPO steel sheet. Finish: ProShield, color specified. Parts List Part# Description Qty - 100610 -00 '/,' x'/," Drive Rivet, AL/SST.....................................2 1/e" x 74" BHCS w/Pin, SST ........................................ 10 105327-01 5" Half Clamp, Specify Color......................................2 100365-00 124864-00 Straight Section (30 '/," Long), Specify Color........... 1/4" x 3/," Drive Rivet, AL/SST.....................................2 124867-00 Right Elbow Section, Specify Color ............................ e 124868-00 Left Elbow Section, Specify Color .............................. LH =Left Hand 124877-00 Exit Section, Specify Color..........................................1 125655-00 Straight Section (15 '/4" Long), Specify Color........... l 128077-00 Support 82", DB, Specify Color..................................1 128261-00 Footer, DB, Specify Color............................................1 128434-00 Support 66", DB, Specify Color..................................1 194414-00 Vertical Ladder, Specify Color ..................................... 1 185595-00 Crossover, Specify Color..............................................1 186026-00 Rushwinder Hood, Specify Color................................1 186165-00 Hand Grip (RH), Specify Color...................................1 186166-00 Hand Grip (LH), Specify Color .................................... l 182262-00 Rung Cap, Black............................................................6 128373-00 Exit Support Hardware Package (DR)....................1 100292-00 3/e" x 1 1/4" BHCS w/Pin Limited Thread Bolt, SST..2 100362-00 %" Flat Washer, SST.....................................................4 111442-00 Rubber Bushing.............................................................2 154942-00 Slidewinder Section Hardware Package..................5 100362-00 3/,' Flat Washer, SST .................................................... 25 113027-00 1/,' x 1 3/e" BHCS w/Pin, SST ..................................... 15 123224-00 1/e" x 1 I1/I6" BHCS w/Pin, SST ................................... 10 196993-00 Rushwinder Slide Entrance Hardware Package... 1 100176-00 1/a" x 3" BHCS w/Pin, SST...........................................2 100196-00 1/e" x 74" BHCS w/Pin, SST ........................................ 10 100351-00 3/," Tee Nut, Specify Color...........................................4 100365-00 1/e" SAE Flat Washer, SST............................................8 100611-00 1/4" x 3/," Drive Rivet, AL/SST.....................................2 100201-00 3/e" x 1 1/2" BHCS w/Pin. SST......................................6 DB - Direct Bury RH - Right Hand LH =Left Hand • - Quantity Depends On Your Order Specifications Vertical Ladder: Weldment comprised of2.375"(60,33 mm) O.D. RS40 (.130"-.140") (3,30 mm -3,56 mm) wall galvanized steel tubing. and 1.315" (33,40mm) O.D. RS20 (.080"- .090") (2,03 mm -2,29 mm) wall galvanized steel tub- ing and '/," (6,35 mm) HRPO flat steel,. Finish: ProShieldx, color specified Slide Section: Rotationally molded from U.V, stabilized linear low density polyethylene, color specified. Hood: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Crossover: Weldment comprised of2.375"(60,33 mm) O.D. RS40 (.130"-.140") (3,30 min -3,56 mm) wall galvanized steel tubing, and '/," (6,35 mm) HRPO steel sheet Finish: ProShield, color specified. Supports: Weldment comprised of 1.900"(48,26 nun) O.D. RS20 (.090" -.100") (2,28 mm -2,54 mm) galvanized steel tubing and 7 GA. (.179") (4,54 mm) HRPO steel strap. Finish: ProShield, color specified. Rung Cap: EPDM, black in color. Exit Footer: Weldmentoomprised of 2.375" (60,33 mm)O.D. RS20 (.095" - .105") (2,41 mm -2,67 mm) galvanized steel tubing and'/4' (6,35 mm) HRPO steel mounting plate. Finish: ProShield, color specified. Clamps: Cast aluminum. Finish: ProShield, color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation/specifications). Installation Time: Approx. 4 1/3 man hours Concrete Req.: Approx. 5.24 cu. ft. Area Req.: 6'(1,83 m) minimum use zone Weight: 309 His. Fall Height: 72" (1,83 m) Installation Instructions 1) (Direct Bury) Refer to the Site Plan for footing locations. 2) Attach crossover to posts at height shown, using 5" half clamps and 3/," x'/," BHCS w/pin with 1/g" tee nuts. Refer to the Crossover At- tachment Detail. 3) Insert end of vertical ladder into crossover tube. 4) Attach hand grips to slide hood, using 3/," x'/," BHCS w/pin and 3/," SAE flat washers. Refer to Slide Hood Assembly. 5) Fasten Rushwinder slide sections, supports and slide hood together loosely starting in the middle and working your way to the outside of each section, using 3/e" x l 3/," BHCS w/pin with 1/," flat washers on the 3 inside holes and 1/s" x 1 11/36" BHCS w/pin with 3/,' flat washers on the 2 outside holes. When all bolts are started, pull the tops flush with each other and tighten. The left elbow sectigafeads (LH) and the right elbow section reads (RH). Attach hood anVxit section last. Refer to the Typical Slide Section DetaiENOTE: goer toFw�'ite plan drawing for location of footings � afR" outaild directtod of Rushwinder slide sections. y' -i -4 C'S . t 6) Place slide hood onto crossover. Line up-hotc5 to SAom old", - over with holes in slide hood, attach using hTrY WS w/ id 3/a" SAE flat washers. Refer to Slide Hoods ssoM Attaglmiam Detail. CD 7) With crossover and vertical ladder steps leVoll, drill th7Dhgh holes in crossover tube into curved loop pole with a I/,' or "F" (tl2tly) drill bit. Insert 1/4" x 34" rivets into holes and hammer rivet pins in until it is flush with head. Refer to Detail. 8) With crossover and vertical ladder steps level, supports and posts plumb, pour concrete footings. Allow concrete footings to cure for a minimum of 72 hours before users are allowed to play on the struc- ture. 9) Attach rang caps to vertical ladder. Refer to Detail. NOTE: Make sure pin is inserted into small hole in back of rung cap before fas- tener is lightened. 10) Drill through 5" half clamps and into 5" posts with a 1/," or "F" (only) drill bit, insert'/," x 1/e" drive rivets into holes through clamps and into posts. Hammer drive rivet pin in until flush with head. 11) Install protective surfacing before users are allowed to play on the structure. Fro 454922 o"c,unmt I%98600 replaces 18936600. RplI dloop pole ani vmical lndder. a/lq landscape structures° SAF NOTE Chcoae a protective wrlatinp material Mat has a Cntical Height Value of et least the 1��/� /A�/A�+ height o/ MB Highest AccesalEl'a Pan/Fall VVi ffli, HegMol Meatjacenteauipnxil(Ref ASTM F148T) ceruned 19397700E c_ _ LO (4) Finish CO Grade ch Labels Finished - Grade Protective Surfacing 0 WARNING Failure to meet the minimum 133/4" clearance between the lowest point of the seat and the protective surfac- ing may result in serious injury. Children have sustained broken legs and ankles due to the seat being installed too low. 173592 Oodle® f Cn Cn cn (4) Finished Grade Labels DETAIL DIRECT BURY ving Legs Sheet 1 of 3 0 2014 by Landscape Shuctures. All nghts reserved. Document #19654200 414, landscape structuresit OSN DETAILS FINISHED GRADE TO SWING SEAT MEASUREMENT SAFETY NOTE Choose a protective surtaong material that has a Critical Height Value of at least the height of the Highest Accessible P..Fall Heightof Ne adjacent equipment (Ref. ASTM F14W ) Swinqs 0 2014 by Landscape Structures. All rights reserved 173592 Oodle° Swi NOTE: Take dimension from the lowest point on the seat. A& landscape structures• DETAIL SWING LEG ATTACHMENT (4) Swing Legs (4) Swing Legs Surfacing Arch a/e' x 3 14" 'eaded Rods (16) a/a" Flange Nuts w/Pin (4) 66 a/m Cables Swing Seat I M (4)665/" 4)66a/ti ? Long DETAIL`' Cables Swing Seat Swings 0 2014 by Landscape Stmctures. 'All nghls reserved Bumpers (4) a/a" x'/aa BHCS w/Pin \ Limited Thread (4) a/;' O.D. x ala" Long Bushings (2) Swing Seat Brackets 173592 Oodle° Swii SAFETY NOTE (Tawe a pgecCve aulatirg lMteMl Cul naa a ChtIW HeipM Value of at least tM nelpnt M Cie Hipheet AaeesiWe PaNFall Heya ClCuaQecwCelrylprrlerR (Ret. ASTh/ F1481) Swing Arch 19397700 ch 101)°ti Cn In (4) Labels (4) %" x'/a" BHCS w/Pin w/ %- SAE Flat Washers Finished Grade Sheet 2 of 3 ��� Document #19854200 U& landscape structures Swing Arch Assembly DETAIL DIRECT BURY (4) Finished Grade (4) Swing Legs Labels Protective Surfacing Crushed Rock Minimum Lls4 Swing Hanger Assembly (4) %" O.D. x 3/." Long (4) Va" X 7/s" BHCS w/Pin Limited Thre PLAN VIEW/FOOTING LAYOUT 9,14 m 173592 OodleP Swi 0 2014 by LaWsca,,e St,,clures, All rights reserved O C:) :*C-) 'Ill,11 cc-:), SAFETY NOTE Q�se a ��ectrve sur1aarrig a si the, he has a Critical Height Value f the IS014001 ,.�Fii height of the Highest Accessible 1.rVF., Heightofibeadjaceht"Mer-ft (Re AS'F&f Rg < Citirlilled FW7) C:) DETAIL 177275a CABLEATTACMENT Swing Hanger Assembly (4) %" O.D. x 3/." Long (4) Va" X 7/s" BHCS w/Pin Limited Thre PLAN VIEW/FOOTING LAYOUT 9,14 m 173592 OodleP Swi 0 2014 by LaWsca,,e St,,clures, All rights reserved O C:) :*C-) 'Ill,11 cc-:), < M C:) =r > Cn I.M Alt landscape structuresr- (2) Swing Seat Brackets swi SAF NOTE has a a p l Height eurlaarq rtatena that las a Cnaral Heigh Value of at leant the IS014001 oa�a "'gavhX lbherl(Re �nd R Cer'I IIeE F1487.) 193977b DETAIL SWING SEAT ATTACHMENT Bottom View 173592 Oodle° S.77 (4) 3/1 x "/e BHCS w/Pin w/'/s' SAE Flat Washers 0 2014 by Largscape Strucwes. All rights resenea Document 4!19854200 N O :n U C-,) I� C `rri Dr 13 R Ln cc (4) 3/1 x "/e BHCS w/Pin w/'/s' SAE Flat Washers 0 2014 by Largscape Strucwes. All rights resenea Document 4!19854200 U illi] landscape structures - Swings 173592 Oodlee Swing Parts List Installation Instructions Part# Description Qty. 193982-00 Swing Seat, Specify Color ........................................ 1 172045-00 Swing Bumper, Black ................................................ 2 174343-00 Swing Leg, Specify Color ......................................... 4 198541-00 66 '/i," Swing Cable, Black ...................................... 4 177254-00 Swing Arch, Specify Color.......................................1 €+1 189148-00 Swing Seat Bracket, Specify Color .......................... 2 184423-00 Oodle Swing Hardware Package .......................... 1 100196-00 '/." x'/," BHCS w/Pin, SST ..................................... 8 100290.00 Y." x %" BHCS w/Pin Limited Thread, SST ......... 8 100353-00 Y." Flange Nut w/Pin, SST ...................................... 16 100365-00 '/." SAE Flat Washer, SST .................................... 8 176539-00 Y." x 3 V: Threaded Rod, SST ................................ 8 127179-00 '/." O.D. x'/." Long Bushing, SST.. ........................ 8 156847-00 Play Safe Label, 5-12 Yrs ......................................... 1 182213-00 Hot Surface Warning Label ....................................... 1 182212-00 Entanglement Warning Label ................................... 1 115176-00 Hard Surface Warning Label .................................... 1 Specifications Swing Seat: Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. Swing Seat Britt: Weldment comprised of 1.66" (42,16 num) O.D. RS20 (.085"-.095") (2,16 rnm-2.41 man) wall galvanized steel tube, 1.000"(25,4 mm) O.D. x.750"(19,05 mm) I.D. 1018 steel tube and 7GA (.179") (4,55 mm) HRPO steel sheet. Finish: ProShield'a, color specified. Cable: Made ofdghtly woven polyester -wrapped, six -stranded galvanized -steel cable with a polypropylene core. (Cable Connectors) 6061-T6 aluminum. Bumper: Molded from U.V. stabilized black EPDM rubber en- capsulating I I GA (.120") HRPO steel sheet. Swing Arch: Weldment comprised of 3.500" O.D. RS20 (.080"- .090" wall) galvanized steel tube and %" thick stain- less steel tabs. Finish: ProShield`, color specified. Swing Leg: 3.500" O.D. RS20 (.080"-.090" wall) galvanized steel tube. Finish: ProShield, color specified. Swing Hanger Assembly: Assembly comprised of 300 series stainless steel knuckle and yoke, stainless steel swing pin, stainless steel spring pin and oilite bushings. Fasteners: Primary fasteners shall be socketed and pinned tamperproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific prod- uct installation specifications). Installation Time: 8- 10 man hours Area Required: 26'x 30'(7,92 m x 9,14 m) minimmn Weight: 395 tbs. Concrete: .52 cu. yards Fall Height: 90" (2,28 m) Dig footings spaced as shown. Refer to the Plan View/Footing Lay- out. 1 Preassemble the Docile swing over a clean non -scratching surface. Attach swing legs to swing arch, using'/," x 3'/: threaded rods and'/ti' flange nuts w/pin. Refer to the Swing Leg Attachment Detail. 1 Stand swing upright onto legs and position in footing holes. Make final adjustments so arch is at proper height and legs are in line with each other. WARNING: Considering the depth of the surfacing material that will be used under the swing, make sure that the finished grade label (attached on each swing leg) is at the appropriate height. This confirms that the swing can be set at a safe and proper el- evation. I Pour concrete footings and let cure for 72 hours before proceeding. I Attach bumpers to swing seat, using'/," x'/," BHCS w/pin and SAE flat washers. I Attach swing seat brackets to swing seat, using'/." x'/," BHCS w/ pin and'/." SAE Flat washers. Refer to the Swing Seat Attachment Detail. I Place'/." O.D. x'/e' long bushings into swing seat bracket tab holes. Attach cables to swing seat brackets, using'/," x'/." BHCS w/pin limited thread. Refer to the Swing Seat Attachment Detail. I Place'/," O.D. x'/i' long bushings into swing hanger clamp assem- bly holes. Attach cables to swing hanger assemblies, using Y." x'/," BHCS w/pin limited thread. Refer to the Cable Attachment Detail. )) Apply Play Safe and Warning Labels, as shown. I ) Install prolective surfacing before users are allowed to play on the structure. IMPORTANT: Verify seat has a safe clearance from the surfacing material as shown on sheet 1. Failure to do so could result In a hazardous installation that may result In serious injury. m x0100000 owvmmt M1985,200 rtplecn p1969]500. Rry1xN swing caNcv N o_ O eJ '(:3 i y'`; i t7v i�� €+1 r� C -n m x0100000 owvmmt M1985,200 rtplecn p1969]500. Rry1xN swing caNcv V_ landscape structures Belt Seat DC INIL_ BOLT LINK �S� (2) a/ ” x 1 t/;' BHCS w/Pin Limned Thread Bolt Link Belt Seat ProGuard Coe Chain a/„x17/„ 6hCS w%Pin Lim- ited Thread (Head Faces User) Bolt Link SAFETY NOTE Cleose a pnotecti. sunetlng malenal that has a Cntical Height Value of et least the height of the Highest AccessiNe Pajg all Height of the adjacent equipment. (Rel. ASTM F14e7) 17745700 inderTuff Coated Chains Or OGuard Coated Chains (2) Bolt Links DETAIL BOLT LINK NOTE: ProGuard Chain Only. Insert Spacers #112501-00 Between Chain Link & Bolt Link. 1 1/ „ .._3 wIPin Lim- ited Thread (Head Faces User) Swings 174018 Belt 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328.8606 888-674-4678 LSI Install Help 888.438.6574 LSI Direct 763-972-6200 Int. FAX (763) 972-3785 Document #21059100 N Cfn C:) n C-)-< r 1 Cr cn co DETAIL BOLT LINK NOTE: ProGuard Chain Only. Insert Spacers #112501-00 Between Chain Link & Bolt Link. 1 1/ „ .._3 wIPin Lim- ited Thread (Head Faces User) Swings 174018 Belt 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328.8606 888-674-4678 LSI Install Help 888.438.6574 LSI Direct 763-972-6200 Int. FAX (763) 972-3785 Document #21059100 Parts List Part # Description Qty - 128842 7 Ft Hiah Beam Belt Swing Seat, Black ............................1 178679 57 7/11" Chain, TenderTuff, Specify Color .................... 2 175251 57'/11" Chain, ProGuard ....... ._........ ........ --- ............ 2 132672 Bolt Link w/Bolt & Specen......................................I 100292 '/r" x I '/," BHCS w/Pin Ltd. Thread, SST.. ................. 2 138915 Bolt Link, SST...............................................................2 112501 Chain Spacer..................................................................4 132635 Bolt Link w/Bolt Hardware Package .......................1 100292-00 '/," x I V/ " BHCS w/Pin Ltd. Thread, SST...................2 138915 Bolt Link, SST .......................... ._...._............................2 128842 8 Ft. Htah Beam Belt Swing Seat, Black ..........._...._.............................. 1 152050 677p Chain, TenderTuff, Specify Color .....................2 174404 677; Chain, ProGuard. ......_ .......................................2 132672 Bolt Link w/Bolt & Spacers......................................1 100292 1/," x I '/; BHCS w/Pin Ltd. Thad, SST...................2 138915 Bolt Link. SST .... -- .......................................................2 112501 Chain Spacer............................................. _._...... ......... 4 132635 Bolt Link w/Bolt Hardware Package .......................1 100292 '/," x I '/," BHCS w/Pin Ltd. Thread, SST .......... ........ 2 138915 Bolt Link, SST._._ ..... .................................................... 2 128842 10 FL HI"h Beam Belt Swing Seat, Black._...............................................1 152052 90 "/,a Chain, TenderTuff, Specify Cola ................... 2 174884 90 "/,,'Chain, ProGuard.............................................. 2 132672 Boit Link w/Bolt & Spacers......................................1 100292 1/," x I '/," BHCS w/Pin Ltd. Thal, SST...................2 138915 Bolt Link. SST. ................................. ............................ 2 112501 Chain Spacer....._._........................................................ 4 132635 Bolt Link w/Bolt Hardware Package .............. ........ 1 100292 1/1" x 1 '/," BHCS w/Pin Ltd. Thread, SST... .... .. .. .. ...2 138915 Bolt Link, SST.._._ ..... .... ._....... - .................. .... ___.... 2 Specifications Chain Spacer: Made from white nylon measuring .080" x .785" O.D. Chain/ProGuard: Steel'/1; straight link chain, 800 Ib. working load limit. Finish: ProGuard. Chain/Costed: Steel'/,," straight link chain, 800 Ib. working bad limit. Finish: TeoderTutl•, color specified. Belt Seats: Molded from U.V. stabilized black EPDM rubber encapsulating a weldment comprised of a 22 GA (.029") spring stainless steel sheet, and (4) .105" thick stainless steel washers. The belt seat elliptical shape measures 7" wide x 26" long x .700" thick. Bolt Link: Stainless Steel. Swings 174018 Belt Seat Fasteners: Primary fasteners shall be socketed and pinned tam- perproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Installation Time: 4, man hour per seat Weight: 8 lbs. (7 Ft. Beam w/ProGuard Chains) 9 lbs. (7 Ft. Beam wllbnderTuff Chains 8 lbs. (8 Ft. Beam w/ProGuard Chains) 9 lbs. (8 Ft. Beam w/TenderTuff Chains) 10 lbs. (10 Ft. Beam w/ProGuard Chains) I I lbs. (10 Ft. Beam w/TenderTuff Chains) Installation Swine Haneers With Double Clevis 1) Attach chains to double clevis using'/r" x 1 '/," BHCS w/pin limited thread, as shown. 2) Attach chains to belt seat using bolt links with'/r" x 1 '/," BHCS w/ pin limited thread. Be sure bolt heads face user. NOTE: Use chain spacers as shown when installing ProGuard chains. 3) Install protective surfacing before users are allowed to play on the structure. I ) Attach chains to aluminum clevis using'/r" x'/," BHCS w/pin limited thread, as shown. 2) Attach chains to belt seat using bolt links with'/r" x 1 4," BHCS w/ pin limited thread. Be sure bolt heads face user. NOTE: Use chain spacers as shown when installing ProGuard chains. 3) Install protective surfacing before users are allowed to play on the structure. o exit C T+-4 —t �7 CT =lc� _Grn y rn SNC •�/� lfi Y fn CD k& landscape structures a/„x11/„ 61 -ICS w%Pin Limited Thread (Not Included) OWN IS014001 SWING HANGER OPTIONS a/„x11/„ 61iCS w%Pin Limited Thread (Not Included) Clevis ;luded) a/ „ x 7/e &CS w/Pin Limited Thread (Not Included) TenderTuff or ProGuard Chains SAFETY NOTE Choose a protective sunaung material that has a Cnacal Height Value of at least the height of the Highest Accessihle PaNFall Height of the adjacent equipment. (Rel ASTM F1487) Clevis auded) TenderTuff or ProGuard Chains 3/"x 1'/ BI -ICS whn Limited Thread (Not Included) 177460b IVIS Dt Included) I TenderTuff or ProGuard ChlAs ._J C'7 —n rn cn ;levis uded) I rCenderTuff or ProGuard hains Swings 174018 Belt Seat Sheet 2 of 2 01 7TH STREET SOU7 ELAND, MINNESOTA 66328.860 88.6744678 LSI Inegll H•1 88138.6674 LSI Dlre 63.972-62001n Ax (7631972-318 Document #21059100 V— landscape structures TenderTuff Chain NOTE: Face bolt heads inward as shown. PfoGUard Chain a Finish Grade 0 1 11 C E R T I F I E D SAFETY NOTE Choose a protective surfacing material That has a Critical Height Value of at least the freight of the Highest Accessible PaWl'all Height of the adjacent equipment. (Ref. ASTM F1467) 18985400 j NOTE: When using ProGuard Ichain, use nylon chain spacers on each side of chain link. x'/a' BHCS w/Pin rU Thread W C7 ••.. i t -4" m =ern Y cn CJ -- Full -Bucket Seat 176038 Full -Bucket Seat, w/Chains Sheet 1 of 2 01 7TH STREET SOOT ELAND, MINNESOTA 66328-860 88-674-4678 LSI InaUll Hel 88438.8674 LSI Oirec 87.972.6200 In AX (763) 972-318 Document 1 • 00 Parts List Swings 176038 Full -Bucket Seat, wichains Part# Description Qty, 186276 7 Ft. High Beam (5" Dia. Beam) Full -Bucket Swing Seat, Black.......................................1 76'/,R Chaim ProGuard..................................................2 141739 43 3/" Chain, TenderTuff, Specify Color.......................2 100290 175248 43'/16" Chain, ProGuard..................................................2 Chain Spacer (For ProGuard Chains Only)..__. ......4 138414 Bucket Seat Hardware Package.................................1 152053 100290 '/," x'/.' BHCS w/Pin Limited Thread, SST..................2 37/x" Chain, ProGuard...................................................2 112501 Chain Spacer (For ProGuard Chains Only).....................4 100290 186276 8 Ft. Hirsh Beam Full -Bucket Swing Seat. Black. ................................ 1 160110 52 °/„” Chain, TenderTuff, Specify Color .......................2 152016 174882 52 °/16"Chain, ProGuard. ._.__..__........................ ...........2 138414 Bucket Seat Hardware Package ..... ................ ........... 1 100290 3/," x'/," BHCS w/Pin Limited Thread, SST. _ ...............2 Chain Spacer (For ProGUard Chains Only) ....... .___ ....... 4 112501 Chain Spacer (For ProGuard Chains ......4 186276 10 FL High Beam Full -Bucket Swing Seat, Black ....................................... l 152051 76'/1e Chaim TenderTuff, Specify Cola......................2 174883 76'/,R Chaim ProGuard..................................................2 138414 Bucket Seat Hardware Package.................................1 100290 3/," x'/," BHCS w/Pin Limited Thread, SST..................2 112501 Chain Spacer (For ProGuard Chains Only)..__. ......4 186276 7 FL High Beam (Tot) Full -Bucket Swing Seat, Black ....................................... 1 152053 37'/," Chaim TenderTuff, Specify Color................_......2 175247 37/x" Chain, ProGuard...................................................2 138414 Bucket Seat Hardware Package ... ........................1 100290 3/," x'/," BHCS w/Pm Limited Thread, SST.. ................ 2 112501 Chain Spacer (For ProGuard Chains Only).....................4 186276 75" Hiph Beam (Toddler) Fut]-Bucket Swing Seat, Black ....................................... l 152016 29'/," Chaim TenderTuff, Specify Color .... ...................2 174881 29'/6" Chain. ProGuard._._..... .......................................2 138414 Bucket Seat Hardware Package _ ....1 100290 %" x'/," BHCS w/Pin Limited Thread, SST...�._...........2 112501 Chain Spacer (For ProGUard Chains Only) ....... .___ ....... 4 Specifications Full -Bucket Seal: Seat shall be molded of U.V. stabilized. high quality. black rubber. encapsulating a 24 gauge stainless steel reinforcement plate. Handle cast from 356-T6 alumi- num alloy with black polyarmor paint finish. Handle attaches to seat with (3)'/," x 1 '/16" long stainless steel rivets. The finished size ofthe full bucket shall be 9" deep x 10'/3" wide. Chain/Coated: Steel 3/16' straight link chain, 800 Ib. working load limit. Finish: TenderTuff; color specified. Chain/ProGuard: Steel'/„" straight link chain, 800 Ib. working load limit. Finish: ProGuard. Fastenen: Primary fasteners shall be socketed and pinned tam- perproof in design, stainless steel (SST) perASTM F 879 unless otherwise indicated (see specific product instal lation/specifications). Installation Time: '/, man hour per seat Weight: 14 lbs. (7 FT. Beam 5" Dia w/fenderTuff Chain) 13 lbs. (7 FT. Beam 5" Die. w/ProGuard Chain) 14 lbs. (8 FT. Beam wrrenderTuff Chain) 14 lbs. (8 FT. Beam w/ProGuard Chain) 17 lbs. (10 FT. Beam w/FenderTuff Chain) 16 lbs. (10 FT. Beam w/ProGuard Chain) 12 lbs. (7 FT. Beam w(FenderTuff Chain) 12 lbs. (7 Fr. Beam w/PnoGuard Chain) I I lbs. (75" Beam w!1'enderTuff Chain) I l lbs. (75" Beam w/ProGuard Chain) Installation Instructions Swine Ilaneers with Double Clevis 1) Attach chains to double clevis using 3/r" x 1 '/," BHCS w/pin limited thread bolts, as shown. 2) Attach chains to full -bucket seat using'/," x %" BHCS w/pin limited thread bolts. Be sure bolt heads face user. NOTE: Use chain spacers as shown when installing ProGuard chains. 3) Install protective surfacing before users are allowed to play on the structure. Anti -wren Swine Hangers No 1) Attach chains to aluminum clevis usinl"x7/,"RMS w/pin limited thread bolts, as shown.�y (") CM 2) Attach chains to full -bucket seat using?:> i r" BICS w/ ited thread bolts. Be sure bolt heads face u! er )TEClre chain spacers as shown when installing ProGuard chg�W M M a 3) Install protective surfacing before we�ye7allo% to In 3) the structure. "rte CY% S & landscape structures` e/"x1 t/ 61 -ICS vithn Limited Thread (Not Included) ;E; CERTIFIED SWING HANGER OPTIONS a/"x 1'/" 01CS w%Pin Limited Thread (Not Included) Clevis luded) x 71 BRCS w/Pin Limited Thread (Not Included) TenderTuff or ProGuard Chains Clevis duded) TenderTuff or ProGuard Chains 3/"x 1 1/ 69 -ICS w%Pin Limited Thread (Not Included) SAFETY NOTE Choose a protective sudaang matins hat has a Cmiral Height Value o1 at least he height M he Highest Accessible PaNFall Height DI the adjacent equipment. (Ret. ASTMF1487) iduded) 177460b i TenderTuff or ProGuard CIATS 0 c++ A -4 --4 :bvie Uded) rCenderTuff or ProGuard hains Swings 176038 Full -Bucket Seat w/Chains Sheet 2 of 2 01 7TH STREET SOUT ELANO, MINNESOTA 66328.860 68-6741878 L81 Install Hel 68136-6674 LSI Direc 63A72.62001n AX (763) 972-378 #21059200 j & landscape structures¢ (4) Labels Options: TenderTuff Coated Chain or ProGuard Coated Chain / 1 I crF11rIE0 NOTE: Tighten all BHCS vv/Pin equally. SAFETY NOTE Choose a prolective surtaong material that has a Critical He1gM Value of at least the freight M Ne Highest Accessible Pariffaii 1 I I HeigMef Vie Fef ASTM lF1487) Certified DETAIL 18448100 END POST ATTACHMENT (8)'/e" Tee earn Nuts & 3/s' Hex Jam Post (8)'!e" x 1 t/;' Nuts BHCS w/Pin b" (4) 5"Half Clamps 9 E Drive Rivets Drive Rivets 0 2 d DETAIL Q O.D Co BACK-TO-BACK Beam4 SWING BEAM ATTACHMENT 7 C (4) 3/e, X 1,/e, 7 9 o m Post BHCS w/Pin q 0 Swing 0 0 m Swing -(e? Beam 9 0 Beam L a q LL OQ (2) " ax /" (4)'/;' Standard t/ o Drive Rivets o Hex Nuts w/'/a' a en SAE Flat 5" O.D. CDT Wtrs Steel �NIIt ' ,' __ Posts cc. � 16"/410 When In Use v Protective PLAN-VIEW/FOOTING-LAYOUT Surfacing � I ' a I I Q I a � r 2 -Place Add. Bav r DETAIL CONCRETE FOOTING Loose Fill Protective post Surfacing 1 , 140" 140" % 3560 3560 Subgrade� / Concrel Minimum Use Footing Zone Q Crushed - Rock swings 177332/177333 Single V '/te' X 2 1/1e' BHCS w/Pin Limited Thread a/e' X 1 I/4" BHCS w/Pin Limited Thread S NOTE: Model num- bers are for swing frames only, order swing seats with chains separately. 24" i Model#177333 Additional Bay 610 Post Swinci Frame ®2012by LaWscaPe Sncturss. Annghtssreserved. Document#18448100 KEY Seat Seat Type Dimension"A" Belt 16'-0" (4,88 m) Flat 16'-0" (4,88 m) Full Bucket 12'-0" (3,66 m) Half Bucket 16'-0'(4,88 m) Molded Bucket 16'-0" (4,88 m) Molded BucketlHamess 13'-0" (3,96 m) Double Infant Full Bucket N/A Clevis Protective PLAN-VIEW/FOOTING-LAYOUT Surfacing � I ' a I I Q I a � r 2 -Place Add. Bav r DETAIL CONCRETE FOOTING Loose Fill Protective post Surfacing 1 , 140" 140" % 3560 3560 Subgrade� / Concrel Minimum Use Footing Zone Q Crushed - Rock swings 177332/177333 Single V '/te' X 2 1/1e' BHCS w/Pin Limited Thread a/e' X 1 I/4" BHCS w/Pin Limited Thread S NOTE: Model num- bers are for swing frames only, order swing seats with chains separately. 24" i Model#177333 Additional Bay 610 Post Swinci Frame ®2012by LaWscaPe Sncturss. Annghtssreserved. Document#18448100 tJ I& landscape structures` Parts List Swings 177332/177333 Single Post Swing Frame Part# Description Beam: Qty en O galvanimd 9=1 tubing, 3"widezinc-plated steel clanya and 1'/4" Z % Add. fied. Hdf Ctamp: Cast aluminum. Finish: PmShield„ color specified. 177498-00 Swing Beam, Specify Color ............................. I .......1 in design, stainless steel (SST) perASTM F 879 unless oth- 107532-00 140" Steel Post Assy., Specify Color .............. 2.......1 cations). 105327-01 5" Half Clamp, Specify Color ......................... 4 ........ Additional Bay - Approx. 3 man hours 132634-00 Double Clevis Hardware Package ............... 2.......2 Additional Bay - Approx. 7 cu. ft. 127068-00 7/1," x 2 7/,."BHCS w/Pin Litd.Thread, SST.. 4.......4 2 -Place - 24'-1" x 32' (7,3 in x9,75 m) For all other seats. 100292-00 34" x 14:' BHCS w/Pin Litd. Thread, SST .. 4.......4 seats. 138917-00 Double Clevis, SST ........................................... 4.......4 other seats. 184516-00 2 -Place Hardware Package ........................... 1 ....... - 100198-00 34" x 1 '/e" BHCS w/Pin, SST ......................... 8 ....... - 100351-00 7/c" Tee Nut, SST ............................................... 8 ....... - 100610-00 1/4" x '/,"Drive Rivet, AL/SST........................ 4....... - 128296-00 3/4" Hex lam Nut, SST ...................................... 8........ - 100611-00 1/4" x %" Drive Rivet, AL/SST........................ 2....... - 156846-00 Play Safe Label, 2-12 Yrs ................................ 1......... 182213-00 Hot Surface Warning Label .............................. 1......... 182212-00 Entanglement Warning Label .......................... 1........ - 115176-00 Hard Surface Warning Label ........................... I ........ . 184419-00 Additional 2 Place Hardware Package....... ........1 100198-00 %" xl '/a" BHCS w/Pin, SST .......................... - .......4 100327-00 3/e" Standard Hex Nut, SST ............................. - .......4 100611-00 1/4" x '/g" Drive Rivet, AL/SST ........................ - .......2 100365-00 3/e" SAE Flat Washer. SST ................................ - ........ 4 156846-00 Play Safe Label, 2-12 Yrs ................................. - ........ 1 182213-00 Hot Surface Warning Label........................................1 182212-00 Entanglement Warning Label ........................... - ........ 1 115176-00 Hard Surface Warning Label ............................ - ........ I " = 5" Half Clamps From 2 PL. Need To Be Used. Specifications Post: See PlayBoostere (PB) General Specifications. Beam: Weldment comprised of 2.375" O.D. RS -40 (.130" - .140") en O galvanimd 9=1 tubing, 3"widezinc-plated steel clanya and 1'/4" housings w/bm= bushings. Finish: ProShielda-color speci- fied. Hdf Ctamp: Cast aluminum. Finish: PmShield„ color specified. Fasteners: Primary fasteners shall be socketed and pinned tamperproof al in design, stainless steel (SST) perASTM F 879 unless oth- S erwise indicated (see specific product installation/specifi- �� cations). Installation Time: 2 -Place - Approx. 6 man hours e -n Additional Bay - Approx. 3 man hours Concrete Req.: 2 -Place - Approx. 14 cu. ft. Additional Bay - Approx. 7 cu. ft. Area Req: 2 -Place - 24'-1" x 24'(7,3 in x 7,31 m) Full bucket seats. 2 -Place - 24'-1" x 32' (7,3 in x9,75 m) For all other seats. Additional Bay - I I' -8"x 24' (3,56 in x 7,31 m) Fu0 bucket seats. Additional Bay - 11'-8" x 32' (3,56 in x 9,75 m) For all other seats. Weight: 2 -Place - 213 lbs. Additional Bay - 129 lbs. Installation Instructions Dig footings spaced as shown. Refer to Concrete Footing Detail 2) Set posts in footing holes and attach swing beam using 5" half clamps with %" x 1 1/a' BHCS w/pin and 3/," tee nuts. Note Detail on front of sheet. Bottom of beam should be 961/2" above finished grade. NOTE: Tighten all BHCS w/pin equally. 3) Fasten Y." hex jam nuts to %" x I '/s" BHCS w/pin. 4) If installing additional bay swings use 3/e' x 1 1/a" BHCS w/pin and 3/e" standard hex nuts with 'Is" SAE flat washers, this hardware will be used to connect swing beam to swing beam. Refer to Back to Back Swing Beam Attachment Detail. 5) Level beam and plumb posts and temporarily prop in position. Pour concrete footings and let cure for 72 hours before proceeding. 6) Attach double clevis to beam using 7/1," x 2 7/16" BHCS w/pin limited thread. 7) NOTE: Refer to specific swing seat installation document for at- taching chains and seats. 8) IMPORTANT: Drill Through hole in 5"half clamps and steel half clamps on beams and into 5"post with a 4,"or F" (onh) drill bit, tap 7/, "x 3/s" drive rivets through aluminum clamps and 7/, "x'/," drive rivets through steel clamps and into post. This will ensure that the clamp assembly cannot slide down the post. 9) Apply Play Safe and Warning Labels, as shown. 10) Install protective surfacing before users are allowed to play on the swing. EvX54545 Daunseap1844810 rnAaaesx1774471n. Added warninglabels w MN arep kage. N O O X4:-5 en O C-,) Q1 a �~1 =�r�t A al � S �� 4D e -n CX) EvX54545 Daunseap1844810 rnAaaesx1774471n. Added warninglabels w MN arep kage. k& landscape structurest DETAIL DGuard Chain) "x 7/a' BHCS w/Pin pHex Jam Nuts (TenderTuff Chain)- 207/ " Con - (2) a/a' x 1/ " BHCS nector Chain w/Pin & a/a' standard Hex Nuts w/ a/a' SAE Flat Washers (2) Pivot Chain Brackets (3) Footman Loops Burke Seat DETAIL\\ `M Bucket Seat H 0-24 x '/z' Head Screws SAFETY NOTE has a ri pal Height material mat w + has a Ctl the Higthest el Height Value M et leacessible WFall ISO y�OQy He ghheighit of the adjacentc quiipment. (Ref. RM i AsrmF14e7) Ceal,lea 17562900 ELEVATION (2) 57 7/t °Chain \ (7' Beam) E (2) 67 7/a' Chain d E (8' Beam) m m d (2) 9018/1e' Chain Cm (10' Beam) c n? c (2)402/ � "Chain a_ (7' Beamg i a ao (2) 5015/ a' Chain a115 (8' Beam} E a (2)731/ Chain r° E E (10' Beam) v� o NOF v �W 0 84 � Finished Grade Dimension to Top DETAIL of Seat HANGER ASSEMBLY — Chain ry m_ (2) TXpical Hanget"glamps D ---I (Not ln„",({I ded) (2)a/a x 1 '/° 1._. BHCS w/Pin (2) Pivot Limited Thread rn BIocNemblies (Not Included) - X7/ BHCS Lin )Pin w//Limited Th Thread DETAIL C BRACKET NOTE: For ProGuard \ Limit' X7 chain, insert (8) nylon BHCS w/�in—B �, spacers between Limited Thread J chain links & brackets Brackets & Pivot Chain BRACKET (4) a/ " x 7/ " TenderTuff BHC°S w/oin Chain Limited Thread W7 °/ " x 7/ " BHCS w/Pin e/;' SAI! Flat Washers (2) Brackets & (2) Pivot Chain Brackets 1 • • • i of 601 7TH STREET SOUTH. DELANO, MINNESOTA 55328-8605 888574-4678 LSI Install Help 888338-6574 LSI Direct 763-972-5200 Int. FAX (763) 972-3185 Document #21059300 S1/1q landscape structuror Swings 177351 Molded Bucket Seat, w/Harness Parts List Part# Description Qty. 182025 Molded Bucket Seat Assembly. Specify Color......... ......... 1 175738 Bumper, Black ... _ ....... _.-____.__............... _......................1 7 Ft High Beam - ProGuard Finished Chains 178679 57'/16"Long, (Front)__ .... --- ............................ 193869 49"/16"Long, (Back)._..._ .................................... 175653 20'/16"Long, (Connector)._._ . ......................... -- 8 Ft High Beam - ProGuard Finished Chains 174404 67 lf Lon& (Front) ...... ............................. ._..... 175619 50"/16"Long, (Back) .......... --- ....... ...... --- ...... 175653 20'/16" Long, (Connector) .... ............................. .. 10 FL High Beam - ProGuard Finished Chains 174884 9011/16' Long, (Front)_..........._..I--..................................2 175623 73'/,' Long (Back). . . .. .. ................................................ 2 175653 20 7/16" Long. (Connector) ................................................. I 7 Ft High Beam - TenderTuff Chains 178679 57 7/1.' Long, (Front), Specify Color ................................. 2 179286 40'/16" Long, (Back), Specify Color.................................2 174571 20'/,6" Long, (Connector), Specify Color ......................... 1 8 Ft. High Beam - TenderTuff Chain 152050 67 %" Long, (Front), Specify Color...._ ..........................- 2 174572 50 "/I6" Long, (Back). Specify Color ........................... ..... 2 174571 20 7/16" Long, (Connector), Specify Color. ..... 1 10 Ft. High Beam -TenderTuff Chains 152052 90'416" Long, (Front), Specify Color........... _._._ .............2 175621 73'/," Long. (Back), Specify Color .................................. 2 174571 20 7/16" Long, (Connector), Specify Color....... .................. 1 208039 Molded Seat w/Yoke Hardware Package .................... 1 100196 %" x'/s" BHCS w/Pin, SST ................................. ........... 100198 '/r" x 1'/6" BHCS w/Pin, SST .......... ..... ---- ..... ._......... 2 100290 1/. x Y." BHCS w/Pin Limited Thread, SST .................... 8 100327 %" Standard Hex Not, SST ............................................... 2 100365 %" SAE Flat Washer, SST ........................ ........ ...... ....._..6 106035 Seat Mounting Bracket......................................................2 112501 Nylon Spacer......... - ..................................._......_.._._......8 128296 '/6" Hex Jam Nut, SST._ .................................................... 2 207709 Footman Loop, SST.................... .......................... ............. 3 160307 Double Pivot Block Assy.... ....... ._................................. 162462 #10-24 x 4." Flat Head Screw, SST 6 Stecitications Bucket Seat Assy.: (Bucket Seat & Yoke) Rotationally molded from U.V. stabilized linear low density polyethylene, color specified. (Pipebolt) Made from 1.125' O.D. 6005- T5 threaded annodized aluminum tube. (Bearings) UHMW PE lubricated. (Brackets) Made from 356- T6 aluminum. Chain/ProGuard: Steel'/16" straight link chain, 800 Ib. working load limit. Finish: ProGuard. Chain/Coated: Steel'/1.' straight link chain, 800 Ib. working load limit. Finish: TenderTuff, color specified. Seat Mounting Bracket: Cast from 535 aluminum magnesium. Bumper: Molded from U.V. stabilized black EPDM rubber encapsulating 11 GA (.120") HRPO steel sheet. Dbl. Pivot Block: Fabricated from 6061-TliAluminum with bronze oil impregnated bearing. Fasteners: Primary fasteners shall be socketed and pinned tam- perproof in design. stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product installation/specifications). Installation Time: Approx. 1 man hour Weight: 50 lbs. (7 Ft. Beam vv/ProGuard Chains) 53 lbs. (7 Ft. Beam w/TenderTuff Chains) 48 lbs. (8 Ft. Beam vv/ProGuard Chains) 51 lbs. (8 Ft. Beam w/TenderTuff Chains) 51 lbs. (10 Ft. Beam w/ProGuard Chains) 55 lbs. (10 Ft. Beam w/TenderTuffChains) Installation Instructions I ) Insert seat mounting brackets into molded -in holes iu..front of bucket seat and attach ends of chain, using '/," x 7/.' BHa r/pin limited thread. See Bracket Detail. NOTE: For Pr�Cymrdrotie lchaitrvmyri (4) melon spacers between chain links anefllz�ts. CI e 2) Attach ends of chain to pivot chain bracket'/ 11 x 1/.' pin limited thread. See Bracket Detail. N09779r Pi"iur chain, insert (4) nylon spacers between chgisrM ar4krc r 3) Attach chains to double pivot blocks, usirt 7 7/s UCS limited thread. 4) (Swing Hangers with Double Clevis) Attach ting hanger double clevis, using'/s" x 1 1/." BHCS w/pin limited thread. (Anti -wrap Swing Hangers) Attach chains to anti -wrap swing hanger clevis, using'/s" x%" BHCS w/pin limited thread. 5) (ProGuard Chain) Attach connector chain to back swing chains at dimension shown, using'/.' x%" BHCS w/pin &'/6" jam nuts. Refer to Detail. (TenderTuff Chain) Attach connector chain to back swing chains at dimension shown, using Y.' x 1 1/s" BHCS w/pin &'/s" standard hex nuts with'/s" SAE Flat Washers. Refer to Detail. 6) Attach footman loops, using #10-24 x 1/t" flat head screws, as shown. Footman loops are used for seat belts (not included). 7) Attach bumper to front of swing seat, using 34" x Y," BHCS w/pin with'/," SAE Flat Washers. 8) Install protective surfacing before users are allowed to play on the structure. 9/& landscape structuress 3/"x11/„ &CS w%Pin Limited Thread (Not Included) (2)3/„x7/„ BHCb w/i3in Limited Thread (Not Included) TenderTuff or ProGuard Chains 3/"x1,/„ 69 !CS w%Pin Limited Thread (Not Included) BHN w4in Limited Thread (Not Included) TenderTuff or ProGuard Chains SAFETY NOTE Choose a p101AFE su NOT materia117 that hes a Critical Height Value of a..— east Ne height of the Highest Accessible PaWl'sti ISO 14001 , Height of the adjacent equipment (Rel ® :I I I I ( asr4 F14e7.) CertI11e0 177462a SWING HANGER OPTIONS Double Clevis (Not Included) Double Pivot Block Double Clevis (Not Included) Pivot Block Clevis (Not Included) 3/11x7/u-� v V BkS w/Pin Double p Limited Thread (Not Included)��� Pivot Block (2)3/„x7/I. BHCb w/Fin Limited Thread (Notlncluded) tJ O . TenderTuff or ProGuard c' s Chains � 3/„x1,/” 61iCS wlPin Limited Thread (Not Included) (2) 3/ 11 x 7/ BHCb wAn Limited Thread (Not Included) TenderTuff or ProGuard Chains Swings Molded 601 7TH STREET SOUTH, DELANO, MINNESOTA 55328-8606 88&574+4678 LSI Install Help 888-43"674 LSI Direct 763.972-1 Double Clevis (Not Included) Double Pivot Block Sheet 2 of 2 Document 9/& landscape structures (4)'/e' Low Crown Cap Nuts w('/1" SAE Flat Washers Age Appropriate Sign DETAIL SIGN ATTACHMENT (2) Signs a" DETAIL (2) 4 x'/, (2) Borders BHCS Torx ( ) Signs Sign Post Small Border (4) %" x t V." BHCS w/Pin wPls' SAE Flat Washers ISO CERTIFIED DETAIL SURFACE MOUNT Model 182803 - Landscape Structures Provided Welcome Sign Model 182804 - Welcome Sign R 1Welcome Sign 01 7TH STREET SOUT ELAND. MINNESOTA 55328-860 88-574-4678 LSI Install Hel 88-0386574 LSI Direc 67-9]2-5200 In AX 17631 972-318 D• 11 (4)'/2' Standard Hex Nuts w/'/,' Sign Post T Ot Post Flat Washers (4)'/2" x 2 1/4" ry Expansion C=) .," Anchors h Concrete Compacted Gravel 9 y. Warning Sign --E' �� tD cn • DETAIL 12� o N DIRECT BURY FOOTING Finished Sign Post Grade {� Pogn st II Subgrade O p Concrete a a Footing _•_. " •: Model 182803 - Landscape Structures Provided Welcome Sign Model 182804 - Welcome Sign R 1Welcome Sign 01 7TH STREET SOUT ELAND. MINNESOTA 55328-860 88-574-4678 LSI Install Hel 88-0386574 LSI Direc 67-9]2-5200 In AX 17631 972-318 D• 11 UvUL landuapo structmr Parts List Part# 211847 211846 211848 211849 211850 211851 211852 180598 181119 193782 193783 Description Qty. WarningSign, Gray.......................................................1 3/" x l'/," BHCS w/Pin, SST._ ............. .............__... -A Age Appropriate Sign, 2-12 Years, Gray ....................... e Age Appropriate Sign, 2-5 Years, Gray ........ .......... e Age Appropriate Sign, 5-12 Years, Gray ............... ....... e Age Appropriate Sign, 1 1/r5 Years, Gray .................... e Age Appropriate Sign, 1 '/s-12 Years, Gray .................. e Age Appropriate Sign, 6-23 Months, Gray ................... e Sign Post (DB), Specify Color....... _... _. _. _. _....._........ Sign Post (SM), Specify Color ............... _. _.. _. _. _...._.. Large Border. Black................... .._.......... ...... . ......1 Small Border, Black ....................................... _. .........1 213258 Age/Warning Sign Hardware Package __._. _..........1 100198 3/" x l'/," BHCS w/Pin, SST._ ............. .............__... -A 100349 '/: Low Crown Cap Nut, SST .................. ._._._._....... 4 100365 '/: SAE Flat Washer, SST.............................................8 168323 08 x % BHCS Tom, SST ......2 169413 1/4-6 Lobe T-15 Tamp. Bit..._ ................... ._............ ._.1 121348 4 Hole (SM) Hardware Package 100266 'l," x 2'/," Expansion Anchor....... 100322/," Standard Hex Nut, SST........... 100363 '/,'Flat Washer, SST .................... DB - Direct Bury SM - Surface Mount e - Quantity Determined By Your Order Specifications Sign Panel: Panel is fabricated from '/"(.125"X3,17mm) alumi- num plate. Finish: ProShield®, grey in color. (Sign) Digital image is tmnsfered to a Y." (.125"X3,17 mm) ProShield coated aluminum plate, then infused into the ProShield. Border: Permalene, black in color. Post: Weldment comprised 2.375" (60,33 mm) O.D.RS20 (.095-.105) (2,41 mm -2,67 men) wall galvanized tube,'/," (6,35 mm) HRPO steel sheet and aluminum post cap. Finish: ProShield, color specified Fasteners: Primary fasteners shall be socketed and pinned tam- perproof in design, stainless steel (SST) per ASTM F 879 unless otherwise indicated (see specific product instal lation/specifications). Installation Time: (DB) Approx. l man hour (SM) Approx. '/, man hour Concrete Req: Approx. 1.31 cu. ft. Weight: (DB) -24 lbs. (SM) - 27 lbs. Welcome Sign Installation Instructions Direct Bury 1) Dig footing hole to depth and diameter shown. 2) Attach sign panels and borders to post as shown, using'/," x 1'/s" BHCS with'/," SAE flat washers and Y." low crown cap nuts with'/" SAE flat washers. Attach signs to borders using 48 x'/2" BHCS Tom. 3) Set sign assembly in footing hole and temporarily brace in plumb position. 4) Pour concrete footing. After concrete has cured. remove bracing. Surface Mount 1) Attach sign panels acrd borders to post as shown. using'/,"x 1'/s"BHCS with'/," SAE flat washers and'/e" low crown cap nuts with'/," SAE flat washers. Attach signs to borders using #8 x'/," BHCS Tom. 2) With sign in proper position, using a'/2" masonry bit and hammer drill, drill 3" deep holes into concrete slab through holes in post plate. Tap '/,"x 2'/," expansion anchors into holes and secure using'/," standard hex nuts with'/," flat washers. O n °r' O _ C-) t - �m 3� M R to D do M t�sntao,sro«,„�,xxirssaoo red+ur sxnsi,m. en,"s,e„c w"��umx„&,m�M�nyd,-,". 134' 186490 WE -SAW 1 PlayBooster® (2-5 years) I / 123331 \ \ �ONpL CE IED / DOUBLE ERS pg5� The play components identified on this plan are IPEMA certified. (Unless model number is preceded with *) The use and layout of these components conform to the requirements of ASTM F1487. To verify product certification, visit www.ipemo.org POLY SLIDE THIS PLAY AREA & PLAY EQUIPMENT IS ^ _ UNLESS OTHERWISE NOTED ON PLAN. IT IS THE MANUFACTURERS OPINION THAT 177715 THE A.D.A. ACCESSIBILITY STANDARDS, ASSUMING AN ACCESSIBLE PROTECTIVE SURFACING IS PROVIDED, AS INDICATED, OR WITHIN THE ENTIRE USE ZONE. ` I CONSTRUCTION, DETAILED SITE INFORMATION COL I SOLUTIONS SHOULD BE OBTAINED, EVALUATED, & L --- DIMENSIONS OF PLAY AREA, SIZE, ORIENTATION, AND \ ------� SHOULD NOT FACE THE HOT AFTERNOON SUN. AN�H 165624 I I ASTM F1487 STANDARD CONSUMER SAFETY PERFORMANCE SPECIFICATION FOR PLAYGROUND 173592 REVISION). THE SUBSURFACE MUST BE WELL I I IT MUST BE TILED OR SLOPED 1/8- TO 1/4' PER FOOT TO A STORM SEWER OR A "FRENCH DRAIN". 168100 DOME SWING PANEL i BUBBLE N \ — / NKH / LANDSCAPE STRUCTURES, INC. I I I SENSSORY PH: 1-800-328-0035 FAX: 1-763-972-6091 I 124863 I I I 8 20 15 85697-1-2 123284 \ / r-------1 85697-2-1 CENTER WALLY Date I Initials SUDEWI� HEXA \ \ , 165780 \ \ \ , \ / \ / �W/PIPE IMAGINATION� — L------� TU 62RBOTWISTER 005PAM! 115227 FLYWHEEL 153UM MINI SUMMIT \ BARRIER \ TABLE TOWER \ MOLDED / SPINNER \ / 144'DECK DB ONLY _ — — \168100 8 BEAM HEIGHT I W/RPE BARRIER \ 114373 / DS ONLY \ I 116249 \ SENSORY PLAY / 42* T 144'DECK DB ONLY SINGLE POSTSWING / I \ I VERT, LADDER — — — — — J / PANEL / \ / 1166ER \ RP I / / \ 4 / � / \ I W/WE iI I W/PROGUARDNS 1DECK) 8' BHEIGHT BM � / 130567 n ( 72' DECKCK ) O / I LEFT \ 48 ) HEX SHINGLE \ 152179 EL \ RANSriFE $ / i \ I \ \ / I / 40 I \ 12' SEAT HEIGHT SENSORY 1 n I I PB 2-5 YRS 1 6 / 8' BEAM HEIGHT \\ WALLY LH \ / \ SPINNER / / 128252 UDDER l \ I BELT SEAT I PLAO5 ACCESSIBLE RING-A-BELL PANEL 119641 1 I - — — I 168101 DB ONLY w 4!E //88 220• STEEL R" \ \ I / SINGLE POST SWING \ SENSORY PLAYTRAVEL / POST 9 34' BURY TUNNEL 174018 \ 1591 \ CENTER WALL END W ROG OMNISPINI B' BEAM HEIGHT 4 I IM75143199 \ U p 40 I -� I SPINNER / 122033 F---� I 176038 DOUBLE BOBBLE CO" B FULL BUCKET SEAT IUDEE W CM US / SPRING RIDER 1 8 BEW HEIGHT UNITARYRFFRI O _ -- \ / \ Q SINGLE POST SWING 2-5 AGE GROUP / / V 168824 I I 0+0 1 IPANEL \ TOWER BUBBLE PANEL 144'DECK ---�.—.. 165824 TOWER BUBBLE122913 S' BEAM HEIGHT I VDECK Pi7eo79 1n24o \ I I -J \ 158997 158998 SNAKE CUMBER (72 DECK) 4�i SUNBEAM I / \ Wim"EEL 123336 DOUBLE POLY \ SADDLE SPINNER12* POD CLIMBER POD CU 164074 \ \\ \ 116244 WAVE SLIDE \ SEAT SPRINGNGLE BRIDER BBLE\ 10'HEIGHf 144 (ZUML�K) PIPE BARRIER \ // / . (3 )TE / \ t0 / 72 144414 1868092� E-POD/SE1T 182503 185960 145624 CLOUDBURST I WELCOME SIGN / 165960 TOWER PIPE VERT. ASCENT (LSI PROVIDED) SLIDE ---' 2-5 YEARS---- WER TOPIPE — --- I / 201545 BLENDER 193169 14 -POST SWIGGLEKNOTS NO DECKS BARRIER RPE BARRIER (72' DECK) 135730 165824 BARRIER 144.DECK 18244 PIPE BARRIER 72 I I I\ 194659 NETPLE( CLI NET MBER 14 POST MATCH 3 TOWER BUBBLE REAACHOANEL PANEL 144'DECK 114605 ARCH 72�XT, 7EXT. EXTENSION 72 116244 / 152907 DECK LINK 2' 7R DECK) 72 117957 PIPE BARRIER / \ W/SARRIERS 48 PERISCOPE PANE / T�0 STEPS 116244 / \ (72' DECK) 176078 RPE BARRIER / M°R 40 32 vTROOF i 176077COUEr \ i 24 C M° BER \ 8 1 6 TRAVELER CUMBER `I / 152911 TRANSFER WBRACKETS / 3 LEFT POINT ti I RUS 3HWINDER TRANSFER 179594 VIBE 72 207582 ' T"E BEND Ui 193176 E RROCCKK 1 80(442" BURY) TRAVEL 1 / \\ RH STIR \ 182503 WELCOME \ / 19931�70� / (LSI \ 5-12 YEARS \ STAR SEEKER DS ONLY / 168101 SENSORY PLAY CENTER WALL END 186490 WE -SAW 1 PlayBooster® (2-5 years) THIS DRAWING HAS A THUNDERHEAD AND/OR CLOUDBURST ON IT, A FREIGHT QUOTE IS REQUIRED TOTAL ELEVATED PLAY COMPONENTS 13 TOTAL ELEVATED COMPONENTS ACCESSIBLE BY RAMP TOTAL ELEVATED COMPONENTS ACCESSIBLE BY TRANSFER TOTAL ACCESSIBLE GROUND LEVEL COMPONENTS SHOWN TOTAL DIFFERENT TYPES OF GROUND LEVEL COMPONENTS 0 13 7 6 0 7 4 3 Mercer Park Playground Iowa City, IA I / 123331 \ \ �ONpL CE IED / DOUBLE ERS pg5� The play components identified on this plan are IPEMA certified. (Unless model number is preceded with *) The use and layout of these components conform to the requirements of ASTM F1487. To verify product certification, visit www.ipemo.org POLY SLIDE THIS PLAY AREA & PLAY EQUIPMENT IS ^ _ UNLESS OTHERWISE NOTED ON PLAN. IT IS THE MANUFACTURERS OPINION THAT 177715 THE A.D.A. ACCESSIBILITY STANDARDS, ASSUMING AN ACCESSIBLE PROTECTIVE SURFACING IS PROVIDED, AS INDICATED, OR WITHIN THE ENTIRE USE ZONE. ` I CONSTRUCTION, DETAILED SITE INFORMATION COL I SOLUTIONS SHOULD BE OBTAINED, EVALUATED, & L --- DIMENSIONS OF PLAY AREA, SIZE, ORIENTATION, AND \ ------� SHOULD NOT FACE THE HOT AFTERNOON SUN. AN�H I I I I ASTM F1487 STANDARD CONSUMER SAFETY PERFORMANCE SPECIFICATION FOR PLAYGROUND 173592 REVISION). THE SUBSURFACE MUST BE WELL I I IT MUST BE TILED OR SLOPED 1/8- TO 1/4' PER FOOT TO A STORM SEWER OR A "FRENCH DRAIN". 168100 DOME SWING (ENGINEERED WOOD FIBER SUGGESTED) 10787 S.F. I I DESIGNED BY: NKH / LANDSCAPE STRUCTURES, INC. I I I SENSSORY PH: 1-800-328-0035 FAX: 1-763-972-6091 I / I I I 8 20 15 85697-1-2 123284 \ / r-------1 85697-2-1 CENTER WALLY Date I Initials WIGGLE LADDER _ HEXA \ 168105 IMAGINATION� — L------� 005PAM! 115227 153UM MINI SUMMIT \ 1SEAT/iHARNESS TABLE MOLDED ZOO PANEL CLIMBER _ — — \168100 8 BEAM HEIGHT I BONGO16"/ \ 114373 177351 \ i SENSORY PLAY / 42* T W=RD CHAINS HEGHT SINGLE POSTSWING / \ I CENTER WALL I / / PANEL / \ / \ I / / \ 4 / � / \ I / / 32 W/PROGUARDNS 16610e 8' BHEIGHT BM 1e43s4 / 130567 n KALpDOSPW / I LEFT 48 ) HEX SHINGLE \ 152179 EL \ RANSriFE $ / SADDLE SPINNER \ 168100 I \ / I / 40 I \ 12' SEAT HEIGHT SENSORY 193174 I PB 2-5 YRS 1 6 / 8' BEAM HEIGHT WALLY I I I \ / \ SPINNER / \ TRANSFER \ - — — — 128252 UDDER / 56 \ I BELT SEAT ACCESSIBLE RING-A-BELL PANEL 119641 I - — — I 168101 ROUTE OF WIRE CRAWL \ I / SINGLE POST SWING \ SENSORY PLAYTRAVEL / ADDITIONAL TUNNEL 174018 DS / / \ CENTER WALL END W ROG I B' BEAM HEIGHT 4 I IM75143199 \ U p 40 I -� I 122033 F---� I 176038 DOUBLE BOBBLE CO" B FULL BUCKET SEAT IUDEE W CM US / SPRING RIDER 1 8 BEW HEIGHT _ -- W/SHA GER / \ Q SINGLE POST SWING 115222dab V / \ I I 0+0 1 IPANEL SLANT WINDOW3 BUCKETSEAT ---�.—.. \I %ILLROGUUAARD S' BEAM HEIGHT I I 1n24o I I I -J \ /\ BALCONY DECK 152179 I I / \ Wim"EEL 123336 DOUBLE POLY \ SADDLE SPINNER12* / 164074 \ \\ \ WAVE SLIDE \ SEAT SPRINGNGLE BRIDER BBLE\ / \ / 6-/8' RISE \ // / . (3 )TE / \ / 182503 WELCOME SIGN (LSI PROVIDED) i ---' 2-5 YEARS---- — --- THIS DRAWING HAS A THUNDERHEAD AND/OR CLOUDBURST ON IT, A FREIGHT QUOTE IS REQUIRED TOTAL ELEVATED PLAY COMPONENTS 13 TOTAL ELEVATED COMPONENTS ACCESSIBLE BY RAMP TOTAL ELEVATED COMPONENTS ACCESSIBLE BY TRANSFER TOTAL ACCESSIBLE GROUND LEVEL COMPONENTS SHOWN TOTAL DIFFERENT TYPES OF GROUND LEVEL COMPONENTS 0 13 7 6 0 7 4 3 Mercer Park Playground Iowa City, IA :1 • PlayBooster@ (5-12 years) TOTAL ELEVATED PLAY COMPONENTS 17 TOTAL ELEVATED COMPONENTS ACCESSIBLE BY RAMP 0 REQUIRED 0 TOTAL ELEVATED COMPONENTS ACCESSIBLE BY TRANSFER 11 REQUIRED 9 TOTAL ACCESSIBLE GROUND LEVEL COMPONENTS SHOWN 24 REQUIRED 6 TOTAL DIFFERENT TYPES OF GROUND LEVEL COMPONENTS 15 REQUIRED 3 Outdoor Recreation Products Rick Ertz SYSTEM TYPE: PlayBooster DRAWING #: 85697-1-3 landscape PLgy� �ONpL CE IED ERS pg5� The play components identified on this plan are IPEMA certified. (Unless model number is preceded with *) The use and layout of these components conform to the requirements of ASTM F1487. To verify product certification, visit www.ipemo.org THIS PLAY AREA & PLAY EQUIPMENT IS DESIGNED FOR AGES 2-12 YEARS UNLESS OTHERWISE NOTED ON PLAN. IT IS THE MANUFACTURERS OPINION THAT THIS PLAY AREA DOES CONFORM TO THE A.D.A. ACCESSIBILITY STANDARDS, ASSUMING AN ACCESSIBLE PROTECTIVE SURFACING IS PROVIDED, AS INDICATED, OR WITHIN THE ENTIRE USE ZONE. THIS CONCEPTUAL PLAN WAS BASED ON I CONSTRUCTION, DETAILED SITE INFORMATION INCLUDING SITE DIMENSIONS, TOPOGRAPHY EXISTING I SOLUTIONS SHOULD BE OBTAINED, EVALUATED, & L --- DIMENSIONS OF PLAY AREA, SIZE, ORIENTATION, AND I I ------� SHOULD NOT FACE THE HOT AFTERNOON SUN. CHOOSE A PROTECTIVE SURFACING MATERIAL THAT I I I I ASTM F1487 STANDARD CONSUMER SAFETY PERFORMANCE SPECIFICATION FOR PLAYGROUND 173592 REVISION). THE SUBSURFACE MUST BE WELL I I IT MUST BE TILED OR SLOPED 1/8- TO 1/4' PER FOOT TO A STORM SEWER OR A "FRENCH DRAIN". ACCESSIBLE/PROTECTIVE DOME SWING (ENGINEERED WOOD FIBER SUGGESTED) 10787 S.F. I I DESIGNED BY: NKH DB ONLY LANDSCAPE STRUCTURES, INC. I I I I I I L------� PH: 1-800-328-0035 FAX: 1-763-972-6091 I I I 8 20 15 85697-1-2 NKH r-------1 85697-2-1 NKH Date Previous Drawing # Initials — L------� r------� 1SEAT/iHARNESS MOLDED W/PROGUARD CHAINS 8 BEAM HEIGHT I I 177351 MOLDED SEAT/HARNESS 177332 W=RD CHAINS HEGHT SINGLE POSTSWING I ONLY I I I I I L--� I I 174018 BELT SEAT W/PROGUARDNS 8' BHEIGHT BM 177333 SINGLE SWING ADDI IONNAAL BAY 174018 DB ONLY I BELT SEAT W/PRO"M CHAINS I I 8' BEAM HEIGHT I I I I 174018 I I I BELT SEAT W/ LRD CHAINS 8' BEAM HEIGHT 177333 SINGLE POST SWING ADDITIONAL 174018 DS BELT SEAT_ W ROG I B' BEAM HEIGHT I I L I -� I F---� I 176038 FULL BUCKET SEAT W CM US 8 BEW HEIGHT 177333 SINGLE POST SWING ADDITIONAL SAY DB ONLY BUCKETSEAT ---�.—.. %ILLROGUUAARD S' BEAM HEIGHT I I I L - - - - I -J - - - - -� r- I I :1 • PlayBooster@ (5-12 years) TOTAL ELEVATED PLAY COMPONENTS 17 TOTAL ELEVATED COMPONENTS ACCESSIBLE BY RAMP 0 REQUIRED 0 TOTAL ELEVATED COMPONENTS ACCESSIBLE BY TRANSFER 11 REQUIRED 9 TOTAL ACCESSIBLE GROUND LEVEL COMPONENTS SHOWN 24 REQUIRED 6 TOTAL DIFFERENT TYPES OF GROUND LEVEL COMPONENTS 15 REQUIRED 3 Outdoor Recreation Products Rick Ertz SYSTEM TYPE: PlayBooster DRAWING #: 85697-1-3 �_ • 1 L .1 1 �F TIFI(:I; Cortltl*d landscape PLgy� �ONpL CE IED ERS pg5� The play components identified on this plan are IPEMA certified. (Unless model number is preceded with *) The use and layout of these components conform to the requirements of ASTM F1487. To verify product certification, visit www.ipemo.org THIS PLAY AREA & PLAY EQUIPMENT IS DESIGNED FOR AGES 2-12 YEARS UNLESS OTHERWISE NOTED ON PLAN. IT IS THE MANUFACTURERS OPINION THAT THIS PLAY AREA DOES CONFORM TO THE A.D.A. ACCESSIBILITY STANDARDS, ASSUMING AN ACCESSIBLE PROTECTIVE SURFACING IS PROVIDED, AS INDICATED, OR WITHIN THE ENTIRE USE ZONE. THIS CONCEPTUAL PLAN WAS BASED ON INFORMATION AVAILABLE TO US. PRIOR TO CONSTRUCTION, DETAILED SITE INFORMATION INCLUDING SITE DIMENSIONS, TOPOGRAPHY EXISTING UTILITIES, SOIL CONDITIONS, AND DRAINAGE SOLUTIONS SHOULD BE OBTAINED, EVALUATED, & UTILIZED IN THE FINAL DESIGN. PLEASE VERIFY ALL DIMENSIONS OF PLAY AREA, SIZE, ORIENTATION, AND LOCATION OF ALL EXISTING UTILITIES, EQUIPMENT, AND SITE FURNISHINGS PRIOR TO ORDERING. SLIDES SHOULD NOT FACE THE HOT AFTERNOON SUN. CHOOSE A PROTECTIVE SURFACING MATERIAL THAT HAS A CRITICAL HEIGHT VALUE TO MEET THE MAXIMUM FALL HEIGHT FOR THE EQUIPMENT (REF. ASTM F1487 STANDARD CONSUMER SAFETY PERFORMANCE SPECIFICATION FOR PLAYGROUND EQUIPMENT FOR PUBLIC USE, SECTION 8 CURRENT REVISION). THE SUBSURFACE MUST BE WELL DRAINED. IF THE SOIL DOES NOT DRAIN NATURALLY IT MUST BE TILED OR SLOPED 1/8- TO 1/4' PER FOOT TO A STORM SEWER OR A "FRENCH DRAIN". ACCESSIBLE/PROTECTIVE LOOSE FILL MATERIAL (ENGINEERED WOOD FIBER SUGGESTED) 10787 S.F. DESIGNED BY: NKH COPYRIGHT: 9/10/15 LANDSCAPE STRUCTURES, INC. 601 7th STREET SOUTH - P.O. BOX 198 DELANO, MINNESOTA 55328 PH: 1-800-328-0035 FAX: 1-763-972-6091 8 20 15 85697-1-2 NKH 7/1/15 85697-2-1 NKH Date Previous Drawing # Initials �_ • 1 L .1 1 �F TIFI(:I; Cortltl*d Prepared by: Geoff Fruin, Assistant City Manager, 410 E. Washington Sl., Iowa City, IA 52240,(319)356-5410 RESOLUTION NO. 15-316 RESOLUTION SETTING A PUBLIC HEARING ON OCTOBER 20, 2015ON PLANS, SPECIFICATIONS, FORM OF CONTRACT, AND ESTIMATE OF COST FOR THE CONSTRUCTION OF THE MERCER PARK PLAYGROUND REPLACEMENT PROJECT, DIRECTING CITY CLERK TO PUBLISH NOTICE OF SAID HEARING, AND DIRECTING THE CITY ENGINEER TO PLACE SAID PLANS ON FILE FOR PUBLIC INSPECTION. WHEREAS, funds for this project are available in the Mercer Park Playground account #R4186. BE IT RESOLVED BY THE COUNCIL OF THE CITY OF IOWA CITY, IOWA: 1. That a public hearing on the plans, specifications, form of contract, and estimate of cost for the construction of the above-mentioned project is to be held on the 20"' day of October, 2015, at 7:00 p.m. in the Emma J. Harvat Hall, City Hall, Iowa City, Iowa, or if said meeting is cancelled, at the next meeting of the City Council thereafter as posted by the City Clerk. 2. That the City Clerk is hereby authorized and directed to publish notice of the public hearing for the above-named project in a newspaper published at least once weekly and having a general circulation in the City, not less than four (4) nor more than twenty (20) days before said hearing. 3. That the copy of the plans, specifications, form of contract, and estimate of cost for the construction of the above-named project is hereby ordered placed on file by the City Engineer in the office of the City Clerk for public inspection. Passed and approved this 6th day of October , 20 15 MAYOR Approved by ATTEST: c�, 4:.�\ ,., 0 (.<n -a ./ Ld ���� CIl9ACLERK- City Attorney's Office -71-03 Jfs Resolution No. 15-316 ]Page 2 It was moved by Payne and seconded by Resolution be adopted, and upon roll call there were: Mims the AYES: NAYS: ABSENT: x Botchway x Dickens x Dobyns x Hayek x Mims x Payne x Thrognaorton NOTICE OF PUBLIC HEARING ON PLANS, SPECIFICATIONS, FORM OF CONTRACT AND ESTIMATED COST FOR THE MERCER PARK PLAYGROUND REPLACEMENT PROJECT IN THE CITY OF IOWA CITY, IOWA TO ALL TAXPAYERS OF THE CITY OF IOWA CITY, IOWA, AND TO OTHER INTERESTED PERSONS: Public notice is hereby given that the City Council of the City of Iowa City, Iowa, will conduct a public hearing on plans, specifications, form of contract and estimated cost for the construction of the Mercer Park Playground Replacement Project in said city at 7:00 p.m. on the 20th day of October, 2015, said meeting to be held in the Emma J. Harvat Hall in the City Hall, 410 E. Washington Street in said city, or if said meeting is cancelled, at the next meeting of the City Council thereafter as posted by the City Clerk. Said plans, specifications, form of contract and estimated cost are now on file in the office of the City Clerk in the City Hall in Iowa City, Iowa, and may be inspected by any interested persons. Any interested persons may appear at said meeting of the City Council for the purpose of making objections to and comments concerning said plans, specifications, contract or the cost of making said improvement. This notice is given by order of the City Council of the City of Iowa City, Iowa and as provided by law. MARIAN K. KARR, CITY CLERK Printer's Fee $-,S , Q CERTIFICATE OF PUBLICATION STATE OF IOWA, JOHNSON COUNTY, SS: THE IOWA CITY PRESS -CITIZEN FED.IDk42-0330670 L—Sin being duly sworn, say t aq I am the legal clerk of the iowA CITY PRESS -CITIZEN, a newspaper published in said county, and that a notice, a printed copy of which is hereto attached, was published in said paper-1— time(s), aper_ —time(s), on the following date(s): to-(i-lS Legal Clerk Subscribed and sworn to before me this t Z day of 0C -T A. 20 1`5�. Notary/ulalic ADAM JAMES KAHLER Commission Number 785381 My Commission Expires 08/04/2017 NOTICE OF AND THE TO ALL TAXPAYERS OF THE CITY OF IOWA CITY, IOWA, AND Public notice Is hereby given that the CityCouncil of the City of Iowa City,. Iowa, will conduct a .public hearing on plans, specifications, form of contract and estimated cost for the construction of the Mercer Park Playground Replacement Project in said city at 7:00 p.m. on the 20th day of October, 2015, mid meeting to be held in the Emma J. Hai Hall in the City Hall, 410 E. Washington Street in said city, or if said meeting the cay Council thereafter as post- ed bythe City Clerk. Said plans, specifications, form of contract and estimated cost are now on file in the office of the City Clerk in the City Hell in Iowa City, Iowa, and may be inspected by any interested persons. Any interested persons may appear at said meeting of the City Council for thepurpose. of making Objections to and comments con - canning said plans, specifications, contract or the cost of making said improvement. This notice is given by order of the City Council of the City of Iowa City, Iowa and as. provided by law. MARIAN K. KARR, CITY CLERK xm000aemr OCTOBER 12; 2015 Prepared by: Geoff Fruln, Public Works, 410 E. Washington St., Iowa City, A 52240 (319) 356-5010 RESOLUTION NO. 15-339 RESOLUTION APPROVING PLANS, SPECIFICATIONS, FORM OF AGREEMENT, AND ESTIMATE OF COST FOR THE CONSTRUCTION OF THE MERCER PARK PLAYGROUND REPLACEMENT PROJECT, ESTABLISHING AMOUNT OF BID SECURITY TO ACCOMPANY EACH BID, DIRECTING CITY CLERK TO PUBLISH NOTICE TO BIDDERS, AND FIXING TIME AND PLACE FOR RECEIPT OF BIDS. WHEREAS, notice of public hearing on the plans, specifications, form of contract and estimate of cost for the above-named project was published as required by law, and the hearing thereon held; and WHEREAS, funds for this project are available in the Mercer Park Playground account #R4186. NOW, THEREFORE, BE IT RESOLVED BY THE CITY COUNCIL OF THE CITY OF IOWA CITY, IOWA THAT: 1. The plans, specifications, form of contract and estimate of cost for the above-named project are hereby approved. 2. The amount of bid security to accompany each bid for the construction of the above- named project shall be in the amount of 10% (ten percent) of bid payable to Treasurer, City of Iowa City, Iowa. 3. The City Clerk is hereby authorized and directed to publish notice, not less than 4 and not more than 45 days before the date for filing the bids, for the receipt of bids for the construction of the above-named project in a newspaper published at least once weekly and having a general circulation in the city. 4. Sealed bids for the above-named project are to be received by the City of Iowa City, Iowa, at the Office of the City Clerk, at the City Hall, before 2:30 p.m. on the 41' day of November, 2015. At that time, the bids will be opened by the City Engineer or his designee, and thereupon referred to the City Council of the City of Iowa City, Iowa, for action upon said bids at its next regular meeting to be held at the Emma J. Harvat Hall, City Hall, Iowa City, Iowa, at 7:00 p.m. on the 10 day of November, 2015, or at a special meeting called for that purpose. Passed and approved this 20th day of October _,20 15 IT, Fivkej' ATTEST: /rl",) kI 46AA_') CITY CLERK pwengVnastersVesapppds.occ 10/15 Approved by City Attorney's Office Ib Resolution Pio. 15-339 Page 2 It was moved by Bayne and seconded by' Resolution be adopted, and upon roll call there were: Dickens the AYES: PLAYS: ABSENT: X Botchway Dickens Dobyns Hayek Payne Throgmorton NOTICE TO BIDDERS MERCER PARK PLAYGROUND REPLACEMENT PROJECT Sealed proposals will be received by the City Clerk of the City of Iowa City, Iowa, until 2:30 P.M. on the 4th day of November, 2015. Sealed proposals will be opened immediately thereafter by the City Engineer or designee. Bids submitted by fax machine shall not be deemed a "sealed bid" for purposes of this Project. Proposals received after this deadline will be returned to the bidder unopened. Proposals will be acted upon by the City Council at a meeting to be held in the Emma J. Harvat Hall at 7:00 P.M. on the 10th day of November, 2015, or at special meeting called for that purpose. The Project will involve the following: The supply and installation of new playground equipment in replacement of the existing equipment located at Mercer Park. All work is to be done in strict compliance with the plans and specifications prepared by Outdoor Recreation Products, of Ames, Iowa and the City of Iowa City, which have heretofore been approved by the City Council, and are on file for public examination in the Office of the City Clerk. Each proposal shall be completed on a form furnished by the City and must be accompanied in a sealed envelope, separate from the one containing the proposal, by a bid bond executed by a corporation authorized to contract as a surety in the State of Iowa, in the sum of 10% of the bid. The bid security shall be made payable to the TREASURER OF THE CITY OF IOWA CITY, IOWA, and shall be forfeited to the City of Iowa City in the event the successful bidder fails to enter into a contract within ten (10) calendar days of the City Council's award of the contract and post bond satisfactory to the City ensuring the faithful performance of the contract and mainte- nance of said Project, if required, pursuant to the provisions of this notice and the other contract documents. Bid bonds of the lowest two or more bidders may be retained for a period of not to exceed fifteen (15) calendar days following award of the contract, or until rejection is made. Other bid bonds will be returned after the canvass and tabulation of bids is completed and reported to the City Council. The successful bidder will be required to furnish a bond in an amount equal to one hundred percent (100%) of the contract price, said bond to be issued by a responsible surety approved by the City, and shall guarantee the prompt payment of all materials and labor, and also protect and save harmless the City from all claims and damages of any kind caused directly or indirectly by the operation of the contract, and shall also guarantee the maintenance of the improvement AF -1 for a period of one (1) year from and after its completion and formal acceptance by the City Council. The following limitations shall apply to this Project: Specified Start Date: November 23d. 2015 Completion Date: May 13.2016 Liquidated Damages: $100.00 per day The plans, specifications and proposed contract documents may be examined at the office of the City Clerk. Copies of said plans and specifi- cations and form of proposal blanks may be secured at the Office of City Engineer of Iowa City 410 East Washington Street, Iowa City, Iowa, by bona fide bidders. A $50 refundable fee is required for each set of plans and specifications provided to bidders or other interested persons. The fee shall be in the form of a check, made payable to the City of Iowa City. A refund will be issued if re -useable plans and specifications are returned to the City of Iowa City within 14 days of the project award date. Prospective bidders are advised that the City of Iowa City desires to employ minority contractors and subcontractors on City projects. A listing of minority contractors can be obtained from the Iowa Department of Inspections and Appeals at (515) 281-5796 and the Iowa Department of Transportation Contracts Office at (515) 239- 1422. Bidders shall list on the Form of Proposal the names of persons, firms, companies or other parties with whom the bidder intends to subcon- tract. This list shall include the type of work and approximate subcontract amount(s). The Contractor awarded the contract shall submit a list on the Form of Agreement of the proposed subcontractors, together with quanti- ties, unit prices and extended dollar amounts. By virtue of statutory authority, preference must be given to products and provisions grown and coal produced within the State of Iowa, and to Iowa domestic labor, to the extent lawfully re- quired under Iowa Statutes. The Iowa reciprocal resident bidder preference law applies to this Project. The City reserves the right to reject any or all proposals, and also reserves the right to waive technicalities and irregularities. Published upon order of the City Council of Iowa City, Iowa. MARIAN K. KARR, CITY CLERK AF -2 Printer's Fee $. S ( , O ( CERTIFICATE OF PUBLICATION STATE OF IOWA, JOHNSON COUNTY, SS: THE IOWA CITY PRESS -CITIZEN FED.ID#42-003�30670 I, ay, 1 being duly sworn, say thatit am the legal clerk of the IOWA CITY PRESS -CITIZEN, a newspaper published in said county, and that a notice, a printed copy of which is hereto attached, was published in said paper_ time(s), on the following date(s): lb -2-3-1 C Legal Clerk Subscribed and sworn to before me thioda of C D.20K. tar Public ADAM JAMES KAHLER Commission Number 785381 My Commission Expires 08/0412017 OFFICIAL PUBLICATION Completion Date: May 13 2016 NOTICE Liquidated Damages; $100.00 ,per TO BIDDERS MERCER PARK PLAYGROUND dey The plans, specifications and REPLACEMENT PROJECT Sealed proposals will be proposed contract documents may received by the City Clerk of the be examined at the office of the City Clerk. Copies of said plans City of Iowa City, Iowa, until and specifications and form of pro- on the 4th dap of November, bee, posal blanks may be secured at 201P.M 2015. Sealed will be the Office of City Engineer of Iowa ateposals opened immediately by City 410 East Washington Sheet, ehereafter the City Engineer or designee. Bids Iowa City, Iowa, by bona fide bid - submitted by fax machine shalt not ders. be dee be .bid" for A $50 refundable fee is required es of t is Project. poses of this Protect. Proposals for each act of plans and specifics - received after this deadline will be tions provided to bidders or other returned to the bidder unopened. interested persons. The fee shall Proposals will be acted upon by i be in the forth of a check, made the City Council at meeting to be payable to the City of Iowa City. A held In the Emma J. Harvat Hall at refund will be Issued if reusable 7:00 P.M. on the 10th day of plans and specifications are November, 2015, or at .special returned to the City of Iowa City meeting called for that purpose. within 14 days of the project award The Project will involve the follow- date. Ing' The supply and installation of Prospective bidders are advised new playground equipment in that the City of Iowa City desires to employ minority contractors and replacement of the existing subcontractors on City projects. A equipment located at Mercer Park' listing of minority contractors can All work is to be done in strict be obtained from the Iowa Department of Inspections and compliance with the plans and Appeals at (515) 281-5796 and the specifications prepared by Outdoor Iowa Department of Transportation Recreation Products, of Ames, Contracts Office at (515) 239-1422. Iowa and the City of Iowa City, Bidders shall list on the Form of which have heretofore been Proposal the names of persons, approved by the City Council, and am on file for public examination In firms, companies or other parties the Office of the City Clark. with whom the bidder Intends to subcontract. This list shall include Each proposal shall be complet- the type of work and approximate ed on a forth furnished by the City subcontract arl and must be accompanied In a The Contractor awarded the con - sealed envelope, separate from tract shall submit a list on the Forth the one containing the proposal, by of Agreement of the proposed Bub- a bid bond executed by a corpora- contractors, together with quantl- tion authorized to contract as a ties, unit prices and extended dol - surety In the State of Iowa, in the lar amounts. sum of 10% of the bid. The bid By virtue of statutory authority, security, shall be made payable to preference must be given to prod - the TREASURER OF THE CITY OF ucts and provisions grown and IOWA CITY, IOWA, and shall be forfeited to the City of Iowa City In I coal produced within the State of the event the successful bidder Iowa, and to Iowa domesticlabor, to the extent lawfully required fails to enter into a contract within ten (10) calendar days of the City under Iowa Statutes. The Iowa Council's award of the contract reciprocal resident bidder prefer - ence law applies to this Project. and post bond satisfactory to the The City reserves the right to City ensuring the faithful perfor- resect any or all proposals, and also mance of the contract and mainte- nance of said Prosect, if required, reserves the right waive techni- pursuant tot the provisions t this calities and irregulariri ties. Published upon order the City notice and the other contract doc-west a I Council of Iowa City, Iowa. . Bid bonds of the lowest MARIAN K. KARR, CITY CLERK two o two or more bidders may be I retained for a period of not to I exceed fifteen (15) calendar days rn.mmosws OCTOBER 23,2015 following award of the contract, or until rejection is made. Other bid bonds will be returned after the canvass and tabulation of bids is completedand reported to the City Council. The successful bidder will be required to furnish a bond in an amount equal to one hundred per- cent (100%) of the contract price, said bond to be Issued by a responsible surety approved by the City, and shall guarantee the prompt payment of all materials and labor, and also protect and save harmless the City from all claims and damages of any kind caused directly or indirectly by the operation of the contract, and shall also guarantee the maintenance of the Improvement for a period of one (1) year from and after its completion and formal acceptance by the City Council. The following limitations shall apply to this Project: Specified Start Date: November 23rd. 2015 . - Prepared by: Geoff Fruin, Assistant City Manager, 410 E. Washington St., Iowa City, IA 52240 (319)356-5010 RESOLUTION NO. 15-344 RESOLUTION AWARDING CONTRACT AND AUTHORIZING THE MAYOR TO SIGN AND THE CITY CLERK TO ATTEST A CONTRACT FOR CONSTRUCTION OF THE MERCER PARK PLAYGROUND REPLACEMENT PROJECT. WHEREAS, Dostal Construction Co. of Cedar Falls, Iowa, has submitted the lowest responsible bid of $247,500 for construction of the above-named project; and WHEREAS, funds for this project are available in the Mercer Park Playground account #R4186 NOW, THEREFORE, BE IT RESOLVED BY THE CITY COUNCIL OF THE CITY OF IOWA CITY, IOWA, THAT: The contract for the construction of the above-named project is hereby awarded to Dostal Construction Co., subject to the condition that awardee secure adequate performance and payment bond, insurance certificates, and contract compliance program statements. 2. The Mayor is hereby authorized to sign and the City Clerk to attest the contract for construction of the above-named project, subject to the condition that awardee secure adequate performance and payment bond, insurance certificates, and contract compliance program statements. 3. The City Engineer is authorized to execute change orders as they may become necessary in the construction of the above-named project. Passed and approved this 10th day of november _,2015. ATTEST: 12� 7` . / CITY tffRK Approved by City Attorney's Office It was moved by Payne and seconded by Botchway the Resolution be adopted, and upon roll call there were: AYES: NAYS: ABSENT: X Botchway X Dickens X Dobyns X Hayek X Mims X Payne X Throgmorton pweng\masterstawrdcon. doc 11115 FORM OF AGREEMENT THIS AGREEMENT is made and entered into by and between the City of Iowa City, Iowa ("City"), and Dostals Construction Company, Inc. ("Contractor"). Whereas the City has prepared certain plans, specifications, proposal and bid documents dated the 19th day of October, 2015, for the Mercer Park Playground Replacement Project ('Project'), and Whereas, said plans, specifications, proposal and bid documents accurately and fully describe the terms and conditions upon which the Contractor is willing to perform the Project. NOW, THEREFORE, IT IS AGREED: 1. The City hereby accepts the attached proposal and bid documents of the Contractor for the Project, and for the sums listed therein. 2. This Agreement consists of the following component parts which are incorporated herein by reference: a. Addenda Numbers N/A b. 'Standard Specifications for Highway and Bridge Construction," Series of 2012, Iowa Department of Transportation, as amended, C. Plans; d. Specifications and Supplementary Conditions; N e. Notice to Bidders; _ ry C=) f" f. Note to Bidders, m g. Performance and Payment Bond; _ co h. Bidder Status Form; r .n i. Contract Compliance Program (Anti -Discrimination Requirements); j. Proposal and Bid Documents, and k. This Instrument. The above components are deemed complementary and should be read together. In the event of a discrepancy or inconsistency, the more specific provision shall prevail. AG -1 C 3. The names of subcontractors approved by City, together with quantities, unit prices, and extended dollar amounts, are as follows (or shown on an attachment): 4. Payments are to be made to the Contractor in accordance with the Supplementary Conditions. DATED this day of / V p 0cr%'L bC ✓\ 20/S. Ott" _, 4. R--) 111� ATTEST: City Clerk Contractor By (Title) U / � x�►^�� n/ .�lo/'P. ATTEST: (Title) OJT (Company Official) Approved By: ityAttorney'sOfficeI'VS ti 4� AG -2 d c .r '.P Bond#929618900 ORIGINAL BOND OF PERFORMANCE AND PAYMENT BOND Dostals Construction Company, Inc. 13ran c 99nth qt _ Cretna. NE 68028 ,as (insert the name and address or legal title of the Contractor) Principal, hereinafter called the Contractor and Western Surety Company, 333 S. Wabash (insert the legal title of the Surety) Ave., 41st Floor, Chicago, IL 60604 as Surety, hereinafter called the Surety, are held and firmly bound unto the City of Iowa City Iowa, as obligee, hereinafter Two Hundred Forty -Seven Thousand called the Owner, i9he amount of pi,rp —d or) /lnn__ N Dollars ($ 247,soo.00 for the payment for which Contractor j9d Sunst t -o hereby bind themselves, their heirs, executors, administrators, successors and a5signs,;�intly 00 severally. e�j Y' o WHEREAS, Contractor has, as of �'r ;,e/,Sentered into Is T (date) .0 written Agreement with Owner for the Mercer Park Playground Replacement Project; and WHEREAS, the Agreement requires execution of this Performance and Payment Bond, to be completed by ;Contractor, in accordance with plans and specifications prepared by the City of Iowa City„ which Agreement is by reference made a part hereof, and the agreed-upon work is hereafter referred to as the Project. NOW, THEREFORE, THE CONDITIONS OF THIS OBLIGATION are such that, if Contractor shall promptly and faithfully perform said Agreement, then the obligation of this bond shall be null and void; otherwise it shall remain in full force and effect until satisfactory completion of the Project. A. The Surety hereby waives notice of any alteration or extension of time made by the Owner. B. Whenever Contractor shall be, and is declared by Owner to be, in default under the Agreement, the Owner having performed Owner's obligations thereunder, the Surety may promptly remedy the default, or shall promptly: 1. Complete the Project in accordance Agreement, or 2. Obtain a bid or bids for submission with the terms and conditions of the to Owner for completing the Project in accordance with the terms and conditions of the Agreement; and upon determina- tion by Owner and Surety of the lowest responsible bidder, arrange for a contract between such bidder and Owner, and make available, as work progresses (even though there may be a default or a succession of defaults under the Agreement or subsequent contracts of completion arranged under this paragraph), sufficient PB -1 Page 1/4 of Bond funds to pay the cost of completion, less the balance of the Contract Price, but not exceeding the amount set forth in the first paragraph hereof. The term "balance of the Contract Price," as used in this paragraph, shall mean the total amount payable by Owner to Contractor under the Agreement, together with any addenda and/or, amendments thereto, less the amount properly paid by Owner to Contractor. C. The Contractor and Contractor's Surety shall be obligated to keep the improvements covered by this bonds in good repair for a period of one (1) year from the date of formal acceptance of the improvements by the Owner. D. No right of action shall accrue to or for the use of any person, corporation or third party other than the Owner named herein or the heirs, executors, administrators or successors of Owner. IT IS A FURTHER CONDITION OF THIS OBLIGATION that the Principal and Surety, in accordance with provisions of Chapter 573, Code of Iowa, shall pay to all persons, firms or corporations having Contracts directly with the Principal, including any of Principal's subcontrac- tors, all claims due them for labor performed or materials furnished in the performance of the Agreement for whose', benefit this bond is given. The provisions of Chapter 573, Code of Iowa, are a part of this bond to t e same extent as if it were expressly set out herein. SIGNED AND SEALED THIS 17th DAY OF November 20 15 . IN THE PRESLNCE OF: 1 WESTERN SURETY COMPANY /�/) ur ) By- / C o_ Robert T, Cirone(Titlef Atey-in-Fact (Street) 5tl :g bJtl OZ AOMSI�Z _Lincoln. NE 68510 (City, State, Zip) 402-475-7700 (Phone) PB -2 Page 2/4 of Bond Western Surety Company POWER OF ATTORNEY APPOINTING INDIVIDUAL ATTORNEY-IN-FACT Know All Men By These Presents, That WESTERN SURETY COMPANY, a South Dakota corporation, is a duly organized and existing corporation having its principal office in the City of Sioux Falls, and State of South Dakota, and that it does by virtue of the signature and seal herein affixed hereby make, constitute and appoint James M King, Robert T Grone, Suzanne P Westerholt, Jacob J Buss, Thomas L King, Individually :v to of Lincoln, NE, its true and lawful Attomey(s)-in-Fact with full power and authority hereby conferred to sign, seat and "gatk for ia on im%rmlf bonds, undertakings and other obligatory instruments of similar nature -'" - In Unlimited Amounts - Co and to bind it thereby as fully and to the same extent as if such instruments were signed by a duly authorized officer of the Corporation W all the acts of said Attorney, pursuant to the authority hereby given, ere hereby ratified and confirmed. This Power of Attorney is made and executed pursuant to and by authority of the By-law printed on the reverse hereof, duly adopted, as indicated, by the shareholders of the corporation. In Witness Whereof, WESTERN SURETY COMPANY has caused these presents to be signed by its Vice President and its corporate seal to be hereto affixed on this 2nd day of July, 2015. WESTERN SURETY COMPANY A"Paul T. Brutlat, Vice hrsidmt State of South Dakota 1 County of Mumehaha f ss On this 2nd day of July, 2015, before me personally came Paul T. Bmtlat, to me known, who, being by me duty swom, did depose and say: that he resides in the City of Sioux Falls, State of South Dakota; that he is the Vice President of WESTERN SURETY COMPANY described in and which executed the above instrument; that he knows the seal of said corporation; that the seat affixed to the said instmment is such corporate seal; that it was so affixed pursuant to authority given by the Board of Directors of said corporation and Out he signed his name thereto pursuant to like authority, and acknowledges same to be the act and deed of said corporation. My commission expires �`^•�""""�""""""`• f �+ S. EICH February 12, 2021 S. Eich, Notary Public CERTIFICATE I, L. Nelson, Assistant Secretary of WESTERN SURETY COMPANY do hereby certify that the Power of Attorney hereinabove set forth is still in force, and further certify that the By -Law of the corporation printed on the reverse hereof is still in force. In testimony whereof I have hereunto subscribed my name and affixed the seal of the said corporation this 17th day of Novamhe r 9015 WESTERN SURETY COMPANY L. Nelson, Assistant Secretary Form F42804-2012 Page 3/4 of Bond Prepared by: Scott Sovers, Sr. Civil Engineer, 410 E. Washington St., Iowa City, IA 52240 (319)356-5142 RESOLUTION NO. 16-178 RESOLUTION ACCEPTING THE WORK FOR THE MERCER PARK PLAYGROUND REPLACEMENT PROJECT WHEREAS, the Engineering Division has recommended that the work for construction of the Mercer Park Playground Replacement Project, as included in a contract between the City of Iowa City and Dostals Construction Company, Inc. of Gretna, NE , dated November 181' 2015, be accepted; and WHEREAS, the Engineer's Report and the performance and payment bond have been filed in the City Clerk's office; and WHEREAS, funds for this project are available in the Mercer Park Playground account #R4186; and WHEREAS, the final contract price is $247,500. NOW, THEREFORE, BE IT RESOLVED BY THE CITY COUNCIL OF THE CITY OF IOWA CITY, IOWA, THAT said improvements are hereby accepted by the City of Iowa City, Iowa. Passed and approved this 6th day of June 120 16 . ,-�4 "/-,- / � M OR Approved by ATTEST: -)'I � fG 7igt, CITY ERK City Attorney's Office It was moved by Botchway and seconded by Dickens the Resolution be adopted, and upon roll call there were: AYES: NAYS: x x x x x x x Pmng/maslers/acphwrk.do 5/16 ABSENT: Botchway Cole Dickens Mims Taylor Thomas Throgmorton 3d(4)