HomeMy WebLinkAbout2023-06-06 OrdinanceItem Number: 9.a.
CITY OF IOWA CITY
Z%--_ �=Pa COUNCIL ACTION REPORT
June 6, 2023
Ordinance amending Title 17, Chapter 1, Building Code, by adopting the International Building
Code, 2021 edition, including Appendix K, and the International Residential Code, 2021
edition, including Appendix F and Appendix J, and providing for certain amendments
thereof; adopting section 103.6(1)(a) of the Code of Iowa (the state electrical code) and
section 105.4(1)(a) of the Code of Iowa (the state plumbing and mechanical codes); to
provide for the protection of the health, welfare and safety of the residents of Iowa City, Iowa
and Title 17, Chapter 12 to clarify the process for Building Code appeals.
Prepared By: Danielle Sitzman, Development Services Coordinator
Reviewed By: Tim Hennes, Senior Building Inspector
Sue Dulek, First Assistant City Attorney
Geoff Fruin, City Manager
Fiscal Impact: None
Staff Recommendation: Approval
Commission Recommendations: The Board of Appeals recommended approval of the
proposed ordinance at its meeting May 1, 2023.
Attachments: Staff Memo to Board of Appeals
Board of Appeals 5-1-23 minutes DRAFT
Ordinance
Executive Summary:
The City regulates the construction, alternation, relocation, enlargement, replacement, repair,
equipment, use and occupancy of residential and commercial structures through the adoption
of building codes. This is accomplished, in part, through the adoption of the International
Code Council's model codes which are published on a three-year cycle. The proposed
ordinance includes the most recent edition of the model codes along with local amendments.
The Board of Appeals, at their public meeting on May 1, 2023, voted to recommend approval
of the ordinance as proposed.
Background / Analysis:
A model building code is a building code that is developed and maintained by a standards
organization independent of the jurisdiction responsible for enacting the building code into
law. A local government can choose to adopt a model building code as their own. This saves
local governments the expense and trouble of developing their own codes.
The International Codes, or I -Codes, are model codes published by the International Code
Council (ICC) and developed by ICC Members to provide minimum safeguards for homes,
buildings and other structures. ICC uses a governmental consensus process to develop its
codes. The City of Iowa City is a voting member of this organization and participates in
national code development. Based on building science, technical knowledge and past
experiences, model building codes provide protection from human -made and natural
disasters, guard public health and reduce property losses.
The State of Iowa imposes a combination of State required codes and locally adopted codes
upon local jurisdictions. As part of the last code update in 2019, the City has amended its
codes to conform to State regulations requiring all local jurisdictions to adopt the State
Plumbing, Mechanical, and Electrical Codes. The State also adopts a version of the
International Energy Conservation Code (IECC) which is required to be enforced for all
occupancies state wide by local government enforcement agencies. Local jurisdictions have
the option of adopting the remaining State adopted International Building Code (IBC) and
International Residential Code (IRC) codes or a stricter code as determined by the
jurisdiction. The proposed ordinance continues to adopt the required State codes and locally
amended versions of the IBC and IRC model codes.
The attached memo from Tim Hennes, Senior Building Inspector as presented to the Board
of Appeals, highlights the notable changes between the 2018 and 2021 model codes and the
local amendments. Very few significant changes were included in this code cycle. Many of
the proposed local amendments simply maintain existing practices. The proposed changes
were developed in collaboration with other jurisdictions in the Iowa City/Cedar Rapids corridor
to ensure as much consistency as possible. Information on the code adoption process was
also shared with the Iowa City Home Builders Association (HBA).
Adopting the 2021 IBC and IRC codes with amendments as proposed will maintain
consistency with national, state and surrounding jurisdictions, allow designers and builders
uniform standards for design, provide protection from human -made and natural disasters,
guard public health and reduce property losses.
CITY OF IOWA CITY MEMORANDUM
Date: April 25, 2023
To: Iowa City Board of Appeals
From: Tim Hennes, Senior Building Inspector
Re: Notable Changes Contained in the 2021 Edition of Building Codes.
Following are significant changes made by local amendments and notable changes between
the 2018 codes and the 2021 codes.
Building Codes
The majority of amendments to the building codes are for clarification of a code
requirement, to reflect local practices that have evolved from previous building codes
and their amendments and to remain consistent with the Fire Code as amended.
Following are notable changes or proposed new amendments:
Section R302.5.1: Delete the requirement that requires house to garage doors to have
self-closing devices.
Comment: The amendment to delete the requirement maintains current requirements.
The amendment does not prohibit someone from installing such device.
Section R302.13: Delete the requirement to protect the underside of floor/ceiling
assemblies in unfinished basements.
Comment: This amendment eliminates the requirement to drywall the ceiling or sprinkle
an unfinished basement ceiling. The amendment to delete the requirement maintains
current requirements. The amendment does not prohibit someone from installing such
protection.
Section R312.2 (IRC) & 1015.8 (IBC): Delete the requirement to install guards on
operable windows that are located less than 24" above the floor and more than 72"
above the finish surface on the exterior of the building.
Comment: The amendment eliminates the requirement to install guards on all operable
windows that meet specified location criteria. The requirement is not consistent with
other guard location criteria requirements and could conflict with emergency and escape
window opening requirements. The amendment to delete the requirement maintains
current requirements. This amendment does not prohibit the installation of fall protection
devices on windows.
Section R313: Delete the requirement to install a fire sprinkling system in one- and two-
family dwelling and townhouses.
Comment: This amendment eliminates the requirement for structures regulated by the
IRC have an automatic fire suppression system installed. The amendment to delete the
requirement maintains current requirements. The amendment does not prohibit the
installation of a automatic fire suppression system.
Section R314.4: Delete the requirement to interconnect smoke alarms when a home is
being altered, repaired or an addition is added.
Comment: This amendment eliminates the requirement for smoke alarms to be
interconnected when a home is being altered, repaired or an addition is added.
Previous codes have not required this extensive of an update and eliminating the
requirement does not forgive the requirement to install battery operated smoke alarms
when alterations, repairs or additions. The amendment to delete the requirement
maintains current requirements. The amendment does not prohibit someone from
installing such protection.
Section R320.3: Add section to include eight provisions to implement universal design
features that provide accessibility, usability and visit -ability for all.
Comment: The amendment applies only to new dwelling units and is not required for
existing structures for repairs, alterations, change of occupancy or additions unless the
square footage of the addition is more than 25% of the existing structure, then, the
addition must comply. The amendment maintains current requirements.
The minimum usability requirements are as follows:
1. Step -less Entrance: At least one entrance must be designed to provide a
step -less entry.
2. Interior doors: At least one bedroom and one bathroom, if either are provided,
and all other passage doorway header widths, on the level served by the
designed step -less entrance, must be framed to accommodate a minimum 38"
clear rough opening. The framing for the doorway width opening may be reduced
to accommodate any door size.
3. Sanitation facilities: There must be at least one bathroom containing a
water closet (toilet) and lavatory (sink) on the level of the dwelling to be
accessed by the designed step -less entrance. The room shall have a
minimum thirty inches (30") by forty-eight inches (48") clear floor space at the
water closet and lavatory.
4. Wall Reinforcement: A bathroom must be provided with wood blocking
installed within wall framing to support grab bars as needed.
5. Decks: All exterior decks surfaces adjacent to the level served by the
designed step -less entrance must be built within four inches (4") of the dwelling
units finish floor level.
6. Switch and outlet requirements: All wall switches, controlling light
fixtures, ans, a temperature control devices and all receptacles shall be
located in an area between fifteen (15) and forty-eight (48) inches above
finished floor.
7. Electrical panel requirements: : Electrical panels on the level of the dwelling
to a ----accessedy the designed step -less entrance shall be located so that
the individual circuit breakers are located between 15" and 54 " above the
floor.
8. Garages: Must be wired for power operated overhead doors.
Section R327: Delete Section R327 Swimming Pools, Spas and Hot Tubs.
Comment: This section was moved to the body of the code from the appendix in the
previous code cycle. Deleting it results in no change of enforcement for pools, spas and
hot tubs. They are still regulated by the electrical and zoning code.
Adoption of Appendices (IRC and IBC)
Appendix F (IRC) — Radon Control Methods:
Amend the code provision to remove the requirement for testing for radon prior to
moving into a house. The amendment does not prohibit testing prior to occupancy.
Comment: We are in a region known to have high levels of radon gas and this code
provision requires a passive radon system in new homes and additions to existing
homes. A pipe installed from below the basement floor up through the roof will serve as
a passive radon system and has the capability of becoming an active system with the
addition of a fan.
Appendix J (IRC): Existing Buildings and Structures:
Adopt Appendix J
Comment: The purpose of these provisions is to encourage the continued use or reuse
of legally existing buildings and structures. These provisions are intended to permit work
in existing buildings that is consistent with the purpose of this code.
Appendix K (IBC) — Administrative Provisions:
Adopt Appendix K
Comment: These provisions are intended to be a tool for jurisdictions to implement and
enforce the National Electrical Code while using administrative provisions that are
consistent with the International Code Council family of codes. This will allow us to
reference the State Electrical Code without needing a separate ordinance to lay out our
administrative provisions.
Existing Building Code (multifamily and commercial)
Adopted by reference: Section 102.6 in the International Building Code directs us to the
International Existing Building Code (IEBC) for existing structures.
Comment: The IEBC allows and encourages the use and reuse of existing buildings
while requiring reasonable upgrades and improvements for alterations, repairs,
additions, occupancy change, historic and relocated buildings.
Energy Code
Adopt by reference the State Energy Code:
Comment: The State of Iowa adopted the 2012 International Energy Conservation Code
(IECC). Referencing the state energy code provides consistency for designers and
builders.
Accessibility Code
Adopted by reference the State Accessibility Code:
Comment: The State of Iowa Accessibility Code is based on the 2010 ADA Standards for
Accessible Design and requirements of the federal Fair Housing Act. Adopting the state
accessibility codes by reference provides consistency for designers and builders.
Plumbing and Mechanical Codes
Adopt by reference the State Plumbing and Mechanical Codes:
Comment: Iowa Code Section 105.4 requires local jurisdictions to adopt the State Plumbing
and Mechanical Code. Adopting the state plumbing and mechanical codes by reference
provides consistency for designers and builders.
Electrical Code
Adopt by reference the State Electrical Code:
Comment: Iowa Electrical Code applies to all electrical installations across the state and cities
cannot adopt or enforce an electrical code less restrictive than the State Electric Code.
Adopting the State Electrical Code by reference provides consistency for designers and
builders.
cc: Tracy Hightshoe, Director, Neighborhood and Development Services
Danielle Sitzman, Coordinator, Development Services
DRAFT
MINUTES
IOWACITYBOARD OFAPPEALS
May 1, 2023 - 4 PM
HELLING CONFERENCE ROOM, CITYHALL
410 E. WASHINGTON STREET
IOWA CITY, IA 52240
MEMBERSPRESENT: Andrea French, Andrew Martin,Thomas McInerney, GT Karr
MEMBERS ABSENT: Jim Walker
STAFF PRESENT: Tim Hennes (Sr. Building Inspector), Sarah Horning (Development
Services Assistant), Troy Roth (Fire Marshal), Sue Dulek (Assistant City
attorney)
RECOMMENDATIONS TO COUNCIL:
Adoption of 2021 International Building and Fire Codes
CALL TO ORDER:
Chair Andrew Martin called the meeting to order at 4 PM
CONSIDERATION OF MINUTES: April 5, 2023 Board of Appeals minutes
MOTION: McInerney moved to approve the minutes from the April 5, 2023 Board of Appeals
meeting. Seconded by French.
VOTE: Motion passed 4-0.
Discussion and possible recommendation to Council regarding the adoption of the
2021 International Buildina and Fire Codes.
DISCUSSION: Martin commented that the new code seems to have been amended to keep
it the way it is now. Tim Hennes agreed and stated that the main difference between the 2018
and 2021 codes is that the new code allows for mass timber construction, which allows for
up to 18 stories be constructed of wood. Hennes also noted that the city's delay in adopting
the new code was due to the discussion of the state legislatures adopting a state building
code, which would have taken building codes out of the hands of the city all together and
since that did not happen, the staff chose to move forward with the adoption of the 2021
codes.
Hennes stated that the city has worked with neighboring jurisdictions (Johnson County, North
Liberty, Coralville & Tiffin) to be consistent with code enforcement and Roth shared that the four
communities are near identical when it comes to the fire code.
MOTION: McInerney moved to recommend to Council to adopt the 2021 International Building
and Fire Codes as amended. Seconded by Karr.
VOTE: Motion passed 4-0.
ADJOURNMENT:
MOTION: McInerney moved to adjourn meeting, French seconded.
VOTE: Motion passed 4-0.
Meeting adjourned at 4:10 PM.
Chairperson, Board of Appeals Date
Prepared by: Danielle Sitzman, Building Official, 410 E. Washington St., Iowa City, IA 52240
Ordinance No.
Ordinance amending Title 17, Chapter 1 , Building Code, by adopting the
International Building Code, 2021 edition, including Appendix K, and the
International Residential Code, 2021 edition, including Appendix F and Appendix
J, and providing for certain amendments thereof; adopting section 103.6(1 )(a)
of the Code of Iowa (the state electrical code) and section 105.4(1 )(a) of the Code
of Iowa (the state plumbing and mechanical codes); to provide for the protection
of the health, welfare and safety of the residents of Iowa City, Iowa and Title 17,
Chapter 12 to clarify the process for Building Code appeals.
Whereas, the current building code is the 2018 edition of the International Building Code (IBC)
and the International Residential Code (IRC), and the City should adopt the 2021 editions of those
codes; and
Whereas, for purposes of uniformity throughout the State, the State Code requires all local
jurisdictions to adopt the State Plumbing and Mechanical Codes; and
Whereas, the Fuel Gas Code is contained in the State Plumbing Code; and
Whereas, for uniformity in greater Johnson County area, the City should adopt the State
Electrical Code; and
Whereas, the City Code should be amended to reflect current practice that members of the public,
and not just the person submitting the appeal, may address the Board of Appeals during hearings on the
Building Code; and
Whereas, the purpose of this ordinance is to provide for the protection of the health, welfare and
safety of the residents of Iowa City, Iowa.
Now, therefore be it ordained by the City Council of the City of Iowa City, Iowa:
Section I.
1. Sections 17-1, 17-2, 17-3 and 17-4 of the Iowa City Code are hereby repealed and the following
new Sections 17-1, 17-2, 17-3 and 17-4 are enacted in lieu thereof.
17-1-1: Codes adopted: Subject to the following amendments, the 2021 edition of the International
Building Code (IBC) including Appendix K, electrical administrative process, and 2021 edition of the
International Residential Code (IRC) including Appendix F, radon control methods, Appendix J,
Existing Buildings and Structures, are adopted. Additionally, the City further adopts, Section
103.6(1)(a) of the Iowa Code (the Iowa State Electrical Code), Section 105.4(1)(a) of the Iowa Code
(the Iowa State Mechanical Code and the Iowa State Plumbing Code). Collectively, they shall be
known as the Iowa City building code or the building code. Interpretations of the building official may
be guided by publications of the International Code Council, Inc., or the International Existing Building
Code.
17-1-2: Interpretation of Building Code provisions: The provisions of this Code shall be held to
be the minimum requirements adopted for the protection of the health, safety and welfare of the
residents of Iowa City.
Ordinance No.
Page 2
17-1-3: Amendments to code: The following sections of the 2021edition of the International Building
Code and 2021 edition of the International Residential Code are amended as follows:
Section R101.1 of the IRC and 101.1 IBC. Delete Section R101.1 of the IRC and 101 .1 of the
IBC and insert in lieu thereof the following:
R101.1/101.1 Title. These regulations shall be known as the Building Code of Iowa City, hereinafter
referred to as "this code."
Section R105.2 of the IRC and 105.2 of the IBC. Delete Section R105.2 of the IRC and 105.2 of
the IBC and insert in lieu thereof the following:
R105.2/105.2 Work Exempt from Permit. A permit shall not be required for the following:
Building
1. One-story detached accessory structures used as tool -and storage sheds, playhouses and
similar uses, provided the floor area does not exceed 144 square feet provided the structure is not
located in a flood hazard area.
2. Fences not over 6 feet high.
3. Oil derricks
4. Retaining walls which are not over 4 feet in height measured from the top of the footing to the
top of the wall, unless supporting a surcharge or impounding Class I, II or III-A liquids.
5. Water tanks supported directly on grade if the capacity does not exceed 5,000 gallons and the
ratio of height to diameter or width does not exceed two to one (2: 1 ).
6. Sidewalks and driveways not more than 30 inches above grade and not over any basement or
story below and which are not part of an accessible route.
7. Painting, papering, tiling, carpeting, cabinets, counter tops and similar finish work.
8. Temporary motion picture, television and theater stage sets and scenery.
9. Prefabricated swimming pools which are less than twenty-four (24) inches deep, do not exceed
five thousand (5,000) gallons and are installed entirely above ground.
10. Shade cloth structures constructed for nursery or agricultural purposes and not including
service systems.
11. Swings and other playground equipment accessory to detached one and two-family dwellings.
12. Window awnings supported by an exterior wall which do not project more than 54 inches from
the exterior wall and do not require additional support.
13. Movable cases, counters and partitions not over five (5)feet nine (9) inches in height.
14. For structures regulated by the IRC the reapplication of shingles provided
The structure is not in a Historic Preservation Overlay Zone or is not an Iowa City Historic Landmark.
Note: Applying solid sheathing over space sheathing is exempt from a permit..
15. For structures regulated by the IRC reapplication of siding provided: The structure is not in a
Historic Preservation Overlay Zone, or a Conservation District Overlay Zone, or is not an Iowa City
Historic Landmark.
16. For structures regulated by the IRC replacing windows provided:
a. Replacement window(s) is in compliance with Appendix AJ.
b. The structure is not in a Historic Preservation Overlay Zone, or a Conservation District Overlay
Zone, or is not an Iowa City Historic Landmark.
17. For structures regulated by the IRC replacing exterior doors, including garage doors, provided:
a. Replacement door(s) is in compliance with Appendix AJ.
b. Doors are not street facing doors i n a structure located in a Historic Preservation Overlay Zone
or are not an Iowa City Historic Landmark.
Note: screen and storm doors do not require a permit regardless of the location.
Electrical:
1 . Portable motors or other portable appliances energized by means of a cord or cable having an
2
Ordinance No.
Page 3
attachment plug end to be connected to an approved receptacle when that cord or cable is permitted
by this code.
2. Repair or replacement of fixed motors, transformers or fixed approved appliances of the same
type and rating in the same location.
3. Temporary decorative lighting.
4. Repair or replacement of current-carrying parts of any switch, contactor, control device or contact
device of the same type and/or rating.
5. Replacement of non-emergency over-current device of the required ampacity and interrupt rating
in the same location.
6. Repair or replacement of electrodes or transformers of the same size and capacity for signs or
gas tube systems.
7. Temporary wiring for experimental purposes in suitable experimental laboratories.
8. The wiring for temporary theater, motion picture or television stage sets.
Gas:
1. Portable heating, cooking or clothes drying appliances.
2. Replacement of any minor part that does not alter approval of equipment or make such
equipment unsafe.
3. Portable-fuel-cell appliances that are not connected to a fixed piping system and are not
interconnected to a power grid.
Mechanical:
1. Portable heating appliances.
2. Portable ventilation appliances.
3. Portable cooling units.
4. Steam, hot- or chilled-water piping within any heating or cooling equipment regulated by this code.
5. Replacement of any minor part that does not alter approval of equipment or make such
equipment unsafe.
6. Portable evaporative coolers.
7. Self-contained refrigeration systems containing 10 pounds (4.54 kg) or less of refrigerant or that
are actuated by motors of 1 horsepower (746 W) or less.
8. Portable-fuel-cell appliances that are not connected to a fixed piping system and are not
interconnected to a power grid.
9. The replacement of fixed appliances provided however that the replacement appliance is in the
same location and has a rating equal to or less than the appliance being replaced, and it is not
necessary to remove, replace, alter, or install any additional ductwork or piping.
Plumbing:
1. The stopping of leaks in drains, water, soil, waste or vent pipe; provided, however, that if any
concealed trap, drainpipe, water, soil, waste or vent pipe becomes defective and it becomes
necessary to remove and replace the same with new material, such work shall be considered as
new work and a permit shall be obtained and inspection made as provided in this code.
2. The clearing of stoppages or the repairing of leaks in pipes, valves or fixtures, and the removal
and reinstallation of water closets, provided such repairs do not involve or require the replacement
or rearrangement of valves, pipes or fixtures.
3. The replacement or removal and reinstallation of any fixture or appliance, provided, however,
that the fixture or appliance is installed at the same location and it is not necessary to remove,
replace, alter, or install any piping.
Exemption from the permit requirements of this Code shall not be deemed to grant authorization for
any work to be done in a manner in violation of the provisions of this Code or any other laws or
ordinances of this jurisdiction.
Section 105.8 of the IBC and 105.10 of the IRC. Add two new Sections 105.8 and 105.8.1 to the
IBC and R105.10 and R105.10.1 to the IRC as follows:
3
Ordinance No.
Page 4
105.8(IBC) R105.10(IRC) Demolition permits required. A demolition permit shall be required as
follows:
1.For the removal of any building or structure.
2. For the removal of any portion of a building (i.e. porch, porch railing, decorative brackets and trim,
dormers, chimneys, etc.) that is located within a Historic Preservation Overlay Zone or a
Conservation District Overlay Zone, or is an Iowa City Historic Landmark.
105.8.1(IBC) and R105.10.1 Requirements.
1 . The applicant for any demolition permit shall state on the application the proposed disposal plans
for all demolition materials.
2. No demolition permit shall be issued until seven (7) working days after the date an application
has been properly filed and said demolition permit shall not be effective until applicant has posted
the premises to be demolished with a notice to be provided by the City and as directed by the City.
Exceptions:
1. Accessory buildings as defined in the Iowa City Zoning Ordinance provided they are not
located within a Historic Preservation Overlay Zone or a Conservation District Overlay Zone
or is an Iowa City Historic Landmark.
2. Dangerous buildings.
Section 105.9 of the IBC and R105.11 of the IRC. Add two new Sections 105.9 to the IBC and
R105.11 to the IRC as follows:
105.9 (IBC) and R105.11 (IRC) Permittee:
1. An electrical, plumbing or mechanical permit may be issued to any person holding a valid
master license for the respective trade as described in Section 17-11-1 of the Iowa City Code, or to
any company who employs a duly licensed master in the respective trade on a full-time basis who
supervises the work of the apprentice and or journeymen during the company's normal business hours.
2. Homeowners of owner occupied, detached single family dwellings qualifying for the
homestead tax exemption may acquire an electrical, plumbing and/or mechanical permits for their
residence and accessory structures (not an apartment or rental unit or apartment building), not to
include electrical dwelling service upgrade or replacement. Prior to issuing a permit to perform electrical
work the homeowner shall pass the Iowa City Electrical Homeowner's exam. Owner occupied means
the dwelling is the owner's principal residence.
3.The homeowner's test required in subsection 2 of this section may be waived if the applicant is a
duly licensed electrician with a minimum of a journeyman status.
Section R107.3 of the IRC and Section 108.3 of the IBC. Amend Section R107.3 of the IRC and
Section 108.3 of the IBC as follows:
R107.3 (IRC) 108.3 (IBC) Temporary Power: Replace the "NFPA 70" with "Iowa State Electrical
Code."
Section R108.2 of the IRC and Section 109.2 of the IBC. Delete Section R108.2 of the IRC and
Section 109.2 of the IBC and insert in lieu thereof the following:
R108.2 (IRC) 109.2 (IBC) Permit Fees and Valuations. The determination of permit fees and project
valuation under any of the provisions of this Code shall be made by the Building Official.
R108.2.1 (IRC) 109.2.1 (IBC) Valuations.
Project Valuation: The total value of all construction work for which the permit is issued, including all
finish work, painting, roofing, electrical, plumbing, heating, air conditioning, site grading, paving,
landscaping, elevators, fire extinguisher and fire alarm systems and other permanent equipment.
Building Permit Value: The total value of all construction work for which the permit is issued, including
all finish work, painting, roofing, site grading, paving, landscaping, elevators, and other permanent
equipment. (Does not include electrical, plumbing, heating, air conditioning, fire extinguisher and fire
alarm systems. The value of this work will be used to determine their permit fees.
R108.2.2 (IRC) 109.2.2 (IBC) Permit Fees.
Building Permit Fee: Is based off the total Permit Value of all construction work for which the permit is
4
Ordinance No.
Page 5
issued, as well as all finish work, painting, roofing, site grading, paving, landscaping, elevators, and
other permanent equipment. (Does not include electrical, plumbing, heating, air conditioning, fire
extinguisher and fire alarm systems. The value of this work will be used to determine their permit fees.
Electrical, Mechanical, Plumbing, Fire Alarm, Fire Sprinkler, and Sewer and Water Permit Fees: The
individual fees for each of these permits is base off the Permit Value of all construction work for which
the permit is issued.
The fee for any permit shall be as set forth in the permit fee schedule as established by resolution of
the City Council.
Section R108.3 of the IRC and Section 109.3 of the IBC. Delete Section R108.3 of the IRC and Section
109.3 of the IBC and insert in lieu thereof the following:
R108.3 (IRC) 109.3 (IBC) Plan Review Fees. When a plan or other data are required to be submitted
by Section 106 and the value of the proposed building or work exceeds fifteen thousand dollars
($15,000), a plan review fee shall be paid before the permit may be issued. Should the project be
abandoned and the permit not issued after the plan review has been started, the plan review fee
shall still be due and payable. The plan review fee shall be as set forth by resolution of City Council.
Plan review fees are separate fees from the permit fee specified in Section R108.2 and 109.2
and are in addition to permit fees.
Section R108. 5 of the IRC and Section 109.6 of the IBC: Delete Section R108.5 in the IRC and
Section 109.6 of the IBC and insert in lieu thereof the following:
R108.5 (IRC) 109.6 IBC Refunds: The Building Official may authorize the refunding of any fee
paid hereunder which was erroneously paid or collected. The Building Official shall not authorize
the refunding of any fee paid except upon written application filed by the original permittee within
one hundred eighty (180) days from the date of fee payment.
Section R108.6 of the IRC and Section 109.4 of the IBC. Delete Section 108.6 of the IRC and
Section 109.4 of the IBC and insert in lieu thereof the following:
R108.6 (IRC) 109.4(IBC) Work commencing before permit issuance: Any person who commences
work on a building, structure, electrical, gas, mechanical or plumbing system before obtaining the
necessary permits shall be subject to a fee equal to the amount of the permit fee if a permit were
issued. This fee shall be collected whether or not a permit is issued. This fee is in addition to
the required permit fee. The payment of such fee shall not exempt any person from compliance
with all other provisions of this Code or from any penalty prescribed by law. Only the Building Official
may reduce this fee when it is demonstrated that an emergency existed that required the work to
be done without a permit.
Section R108.7 of the IRC and Section 109.7 of the IBC. Add two new Sections R108.7 to the IRC
and 109.7 to the IBC as follows:
R108.7 (IRC) and 109.7 (IBC) Reinspection Fees:
A re-inspection fee may be accessed for each inspection or reinspection when such work or portion of
such work for which the inspection was scheduled is not complete or when corrections cited are not
made. Reinspection fees may be assessed when plans necessary to complete the inspection are not
readily available to the inspector, access is not provided on the date for which the inspection was
scheduled, or when there are deviations from plans requiring additional plan review. This section is not
to be interpreted as requiring reinspection fees the first time a project is rejected for failure to comply
with requirements of this code, but as a method to control the practice of scheduling inspections before
the project is ready for scheduled inspections.
Section R112 of the IRC and Section 113 of the IBC. Delete Section R112 of the IRC and Section
113 of the IBC and insert in lieu thereof the following:
R112 (IRC) and 113 (IBC) Appeals: See Title 17 Chapter 12 Appeals in the City Code.
Section 202 of both the IBC and IRC. Add new definition as follows:
5
Ordinance No.
Page 6
Authority Having Jurisdiction. The organization, office, or individual responsible for approving
equipment, materials, an installation, or a procedure.
Section 202 of both the IBC and IRC. Add new definition as follows:
Chief Electrical Inspector. A building inspector who either is the authority having jurisdiction or is
designated by the authority having jurisdiction and is responsible for administering the requirements of
this code.
Section 202 of both the IBC and IRC. Add new definition as follows:
Electrical Inspector. A building inspector authorized to perform electrical inspections.
Section 202 of both the IBC and IRC. Add new definition as follows:
Family: See Title 14 Chapter 9 Article A Zoning Definitions in the City Code.
Section 202 of both the IBC and IRC. Add new definition as follows:
Emergency Communications Center. Shall mean the Johnson County Emergency Communications
Center.
Section 202 of the IBC and IRC. Modify definitions as follows:
Habitable space: Add a sentence to the end of the definition of habitable space or room to read as
follows: Basement areas finished to a degree to encourage their use as anything other than storage
or mechanical rooms shall be considered habitable space.
Section R202 of the IRC. Delete definition of Accessory Structure and insert in lieu thereof the
following: Accessory Structure. See Title 14 Chapter 9 Article A Zoning Definitions in the City Code.
6
Ordinance No.
Page 7
Table R301.2 (1) of the IRC Modify by inserting data in the table as follows:
Wind Design Subject to Damage From Flood
Hazards
Topo- NFIP FIRM
graphic Maps
Groun effects, Seismic Winte Ice- p
Air Mean
d Special Design Frost r Barrier
Freezin Annua
Desig Under-
Snow Speed wind Cate- Weatherin line Termite n layment g
Load (mph) region, gory g dept Index Temp
Temp Required
or Wind- h
borne
debris
zone
5/22 2/16/
Moderat
25 107 No A Severe 42" e Heavy -5 F Yes /197 2007 2000 50°F
7
MANUALJ DESIGN CRITERIA
Elevation Latitude Winter Summer Altitude Indoor Design Heating
Heating Cooling Correction Design Temperature Temperature
Factor Temperature Cooling Difference
661' 41° -6° 89° N/A 72° 75° 78°
Cooling Wind Wind Coincident Daily Winter Summer
Temperature Velocity Velocity Wet Bulb Range Humidity Humidity
Difference Heating Cooling
14° 25° 10° 76° M 39 gr/lb diff. 53 gr/lb diff.
Section R302.5.1 of the IRC. Delete Section R302.5.1 of the IRC and insert in lieu thereof the following:
R302.5.1 Opening protection. Openings from a private garage directly into a room used for sleeping
purposes shall not be permitted. Other openings between the garage and residence shall be equipped
with solid wood doors not less than 1 3/8 inches (35 mm) in thickness, solid or honeycomb core steel
doors not less than 1 3/8 inches thick, or 20-minute fire-rated doors.
Section R302.13 of the IRC. Delete Section R302.13 of the IRC entirely.
Section 305.2.3 of the IBC. Delete Section 305.2.3 of the IBC and insert in lieu thereof the following:
305.2.3 Eight or Fewer Children in a Dwelling Unit. A facility such as the above within a dwelling unit
and having eight or fewer children receiving such day care shall be classified as a Group R-3
occupancy or shall comply with the International Residential Code.
Exception: Day care facilities that provide custodial care for 16 or fewer persons for less than 24-hours
per day in a single-family dwelling, and where registered with the State of Iowa Department of Human
Services as child development homes on or before January 1, 2017, are permitted to comply with the
International Residential Code.
Section 310.4.1 of the IBC. Delete Section 310.4.1 of the IBC and insert in lieu thereof the following:
310.4.1 Care Facilities Within A Dwelling Unit. Care facilities within a dwelling unit shall be in
accordance with section 305.2.3.
Section R310.7 of the IRC. Delete Section R310.7 in the IRC and insert in lieu thereof the following:
R310.7 Alterations or repairs of basements in structures built after May 10, 1989. An emergency
escape and rescue opening is not required where existing basements undergo alterations or repairs.
7
Ordinance No.
Page 8
Alterations or repairs in structures built prior to May 10, 1989 shall conform to Appendix AJ Section
AJ 102.4 Replacement windows.
Exception: New sleeping rooms created in an existing basement shall be provided with emergency
escape and rescue openings in accordance with Section R310.1 though R310.6
Section 310.6 Exception 3 of the IRC. Delete Section 310.6 Exception 3 of the IRC entirely.
Section 310.7 of the IRC. Delete Section 310.7 of the IRC entirely.
Section R312.2 of the IRC and 1015.8 of the IBC. Delete Section R312.2 of the IRC and 1015.8 of
the IBC entirely.
Section R313 of the IRC: Delete Section R313 of the IRC entirely.
Section R314.4 of the IRC. Amend Section R314.4 in the IRC by adding an exception as follows:
Exception: Interconnection of smoke alarms in existing areas shall not be required where alterations or
repairs do not result in removal of interior wall or ceiling finishes exposing the structure, unless there is
an attic, crawl space or basement available that could provide access for interconnection without removal
the interior finish.
Section R320.3of the IRC. Add Section R320.3 in the IRC as follows:
R320.3 Accessibility for projects other than those mentioned in Section R320.1 and R320.2.
R 320.3.1 Scope. The provisions of this section are enacted to implement universal design features
that provide accessibility, usability and visit-ability for all.
R320.3.2 Definition. Public funds shall mean funding or assistance from the City of Iowa City or
any agent thereof through any of the following means:
1. a building contract or similar contractual agreement involving a City-funded program or fund;
2. any real estate received by the owner through a subsidy, lease, or donation by the City or its agents;
3. preferential tax treatment, bond assistance, mortgage assistance, or similar financial advantages
from the City or its agents;
4. disbursement of federal or state construction funds including a Community Development Block
Grant; or
5. a City contract to provide funding or a financial benefit for housing.
R320.3.3 Applicability. The amendment applies to new one- and two-family dwellings and is not
required for new townhouses, accessory apartments or existing structures for repairs, alterations,
change of occupancy or additions unless the square footage of the addition is more than 25% of
the existing structure, then, the addition must comply.
Exception: Applies to new townhouses constructed using public funds.
The minimum usability requirements are as follows:
1. Step-less entrance: At least one building entrance must be designed, without
encroaching into any required parking space, that complies with the Iowa City Building Code
standard for an accessible entrance on an accessible route served by a ramp in accordance with
section R311.8 or a no-step entrance. The accessible route must extend from a vehicular drop-
off, or parking to a building entrance. The entry door must have a minimum net clear opening
of thirty-two inches (32").
If public funds are used the step-less entrance must be provided.
Exception:
The building official may waive this requirement based upon the determination that strict compliance
is financially or environmentally impractical.
2. Interior doors: At least one bedroom and one bathroom (if either are provided) and a II oth e r
passage doorway header widths, on the level served by the designed step-less entrance, must be
framed to accommodate a minimum 38" clear rough opening. The framing for the doorway width
8
Ordinance No.
Page 9
opening may be reduced to accommodate any door size
Exception:
1.If public funds are used the minimum door clear opening shall be thirty-two inches (32") when
the door is open ninety degrees (90), measured between the face of the door and the opposite stop.
2.Doors serving closets twenty-four inches (24") or less in depth need not be framed to 38" clear
opening width.
Note: A 34" door hung in the standard manner provides an acceptable 32" opening.
3. Sanitation facilities: There must be at least one bathroom containing a water closet (toilet) and
lavatory (sink) on the level of the dwelling to be accessed by the designed step-less entrance. The
room shall have a minimum thirty inches (30") by forty-eight inches (48") clear floor space at the
water closet and lavatory. The clear floor space can be shared by both fixtures.
The plans must show a shower, bathtub or combination tub/shower can be provided within the room
or an adjoining room without removing part of the concrete floor to provide necessary plumbing to the
future plumbing fixture(s).
If public funds are used a shower, bathtub or combination tub/shower shall be provided within the
room.
Exceptions:
The building official may waive this requirement based on the determination that strict compliance
is financially impractical.
4. Wall reinforcement: A bathroom must be provided with wood blocking installed within wall framing
to support grab bars as needed. The wood blocking, when measured to the center, will be located
between thirty-three inches (33") and thirty-six inches (36") above the finished floor. The wood
blocking must be in all walls adjacent to and behind a toilet.
Exception: Backing is not required behind pre-manufactured showers and bathtubs.
5. Decks: All exterior decks surfaces adjacent to the level served by the designed step-less
entrance must be built within four inches (4") of the dwellings finish floor level.
Note: At grade patios are exempt from this requirement.
6. Switch and outlet requirements: All wall switches, controlling light fixtures, fans, all temperature
control devices and all receptacles shall be located in an area between fifteen (15) and forty-eight
(48) inches above finished floor. The height will be determined by measuring from the finished floor
to the center of the device. When the control or receptacle placement is prohibited by the height
of the window or design feature, alternative locations may be approved by the building official.
7. Electrical panel requirements: Electrical panels on the level of the dwelling to be accessed by
the designed step-less entrance shall be located so that the individual circuit breakers are located
between 15" and 54 " above the floor.
8. Garages: Must be wired for power operated overhead
Section R322 of the IRC. Delete section R322 of the IRC and insert in lieu thereof the following:
R322. See Title 14 Chapter 5J Flood Plain Management Standards in the City Code.
R322.1 Flood Resistive Materials. Building materials and installation methods used for flooring and
interior and exterior walls and wall coverings below the elevation required in Title 14 Chapter 5J Flood
Plain Management Standards,in the City Code shall be flood damage-resistant materials that conform
to the provisions of FEMA TB-2.
Section R326 of the IRC. Delete Section R326 of the IRC entirely
Section R327 of the IRC. Delete Section R327 of the IRC entirely.
Section R403.1.4.1 of the IRC. Modify by deleting all exceptions and inserting in lieu thereof the
following:
Exceptions:
1. One story detached accessory buildings of wood or steel frame construction not used for human
occupancy and not exceeding one thousand (1,000) square feet in floor area may be constructed
9
Ordinance No.
Page 10
using slab on grade construction as follows. The slab shall be three and one-half inches thick,
poured monolithically with thickened perimeter footings extending twelve inches (12") below finish
grade and be twelve inches (12") wide at the base. The top of the foundation shall not be less
than six inches (6") above finish grade. Reinforcement of the slab, including the thickened portion,
shall be minimum 6x6-10/10 welded wire mesh, #4 deformed reinforcing bars at twenty-four inches
(24") on center each way or fiber mesh reinforced concrete.
2. Freestanding accessory structures not used for human occupancy and not exceeding four
hundred (400) square feet in floor area or less and an eave height of ten (10) feet or less above
grade may be constructed on wood plate or skids.
3. Decks not supported by the structure need not be provided with footings that extend below the
frost line.
Section 403.5.6 of the IBC: Add a new Section 403.5.6 as follows:
403.5.6 Emergency escape and rescue. Emergency escape and rescue openings specified in
Section 1031 are not required.
Section R404.1.1 of the IRC: Amend Section R404.1.1 of the IRC by adding an Exception after number
2 as follows:
Exception: Foundation walls with unbalanced lateral forces created by finish grade, i.e. walkout
basements which are exempt from the Iowa Architectural Act shall be designed by a licensed structural
engineer or constructed in accordance with the Table R404.1.1(5) and diagram as follows:
Table R401.1.1(5)
CB=Corner Bars
S=Span of Wall
T=Thickness
D=4'Offset
2"Minimum Inside Face of
D s Wall to edge of reinforcing
s
CB \ 8"&12"Foundation Walls S
-— Provide corner bars to match horizontal
foundation wall reinforcing Into wall 2'
T
span Wall Thickness Horizontal Corner Bar
IS/ R) Reinforcing (CB) r . Ii See Schedule for
10'or less 8" n4 @ 12" 2'-0" M Horizontal Reinforcing
10'to 12' 8" 85 @ 12° 2'-
12'to 14' 8' 116 @ 12" 3'-0^ I
#4 Reinforcing Vertical
14'to 16' 12^ qs @ 12" z'-6°
30"Q.C.Typical
16'to 18' 12" 46 Al 14" 3'-0" 4`
18'to 20' 12" 46 @ 12" 3'-0"
64 Reinforcing Dow
.�.
Frost Wall&Footing(Walkout)
Notes.
1.Corner Bars are required in addition to horizontal reinforcing. •
„
2.All Corner Bar reinforcing splices shall be lapped a minimum of 24". }
3.If span(Si is greater than 16',the minimum dimension of(D)shall be 6'. , b"
v v.. p.
10
Ordinance No.
Page 11
Section 502.1 of the IBC(F). Delete Section 502.1 in its entirety and insert in lieu thereof the following:
502.1 New and existing buildings shall have approved address numbers, building numbers or
approved building identification placed in a position that is plainly legible and visible from the street or
road fronting the property. Address identification characters shall contrast with their background.
Address numbers shall be Arabic numbers or alphabetical letters. Numbers shall be sized as specified
in Table 502.1. Measurements to determine the minimum number size shall be measured from the
approved address location to the center line of the street for which the premises is addressed. Where
access is by means of a private road and the building cannot be viewed from the public way, a
monument, pole or other sign or means shall be used to identify the structure. Address identification
shall be maintained.
Table 502.1
Minimum Address Size a,b,c,d
Distance from the centerline of the Public Way (ft) Minimum Height (in) Minimum Stroke Width (in)
Less than 100 4 1/2
100 199 6 3/4
200 299 8 1
For each additional 100 Increase 2 Increase 1/2
a) Exterior suite identification, minimum height shall be 4 inches and stroke width shall be 1/2 inch.
b) Interior suite identification, minimum height shall be 3 inches and stroke width shall be '/4 inch.
c) Measurements to determine the minimum number or letter size shall be measured from the
approved
address location to the center line of the street for which the premise is addressed.
d) Minimum height and minimum stroke may be increased by the Code Official.
Section R507.10.2 of the IRC. Delete Section 507.10.2 entirely.
Section R807.1 of the IRC. Modify by adding a sentence at the end of the second paragraph as
follows:
The opening shall not be located in a closet, bathroom, mechanical room, laundry room, or similar
room or location.
Section 903.3.5.1 of the IBC (F).. Delete Section 903.5.1 of the IBC and insert in lieu thereof the
following:
903.3.5.1 A single domestic and automatic fire sprinkler system water supply. If the city water
provider requires a single domestic and automatic fire sprinkler system supply, then the water supply
shall be split outside of the building and shall have a shutoff provided for the domestic service after
the split outside of the building. The total domestic demand is required to be added to the fire
sprinkler demand.
Section 903.3.5.2 of the IBC (F). Delete this section.
Section 903.3.5.3 of the IBC (F). Add a new section 903.3.5.2 to read as follows:
903.3.5.3 Water supply safety margin. The fire sprinkler system hydraulically calculated demand per
11
Ordinance No.
Page 12
NFPA 13 or NFPA 13R including required hose stream allowances, and domestic water demand if
required by section 903.3.5.2, must be a minimum 10%, but not less than 5 psi below the water
supply flow test curve, the flow test must have been conducted within 90 days of fire sprinkler plan
submittal to the city and third party reviewer(if applicable) or as deemed current and approved by the
local water jurisdiction. The base of riser psi at the time of acceptance test shall also be 10% but not
less than 5 psi above the most demanding hydraulically calculated pressure.
Section 903.4 of the IBC (F). Delete exception number 5 without substitution.
Section 903.4.2 of the IBC(F). Delete the section 903.4.2 and replace with:
903.4.2 Alarms. An approved weatherproof horn/strobe device shall be mounted directly above the
fire department connection between seven (7) and ten (10) feet in height above grade. The water-flow
alarm device shall be activated by water flow equivalent to the flow of a single sprinkler of the
smallest orifice size installed in the system. Approved and supervised audible visual notification
appliances shall be installed on each level of the interior of the building as required by the fire code
official and NFPA 72. Where a fire alarm system is installed, actuation of the automatic sprinkler
system shall actuate the building fire alarm system.
Section 903.6 of the IBC (F). Add a new Section 903.6 to the IBC to read as follows:
903.6 Zones. Automatic sprinkler system zones shall not exceed the area permitted by NFPA 13 or
NFPA 13R and shall provide a sprinkler control valve and waterflow device for each normally
occupied floor. The location of sprinkler control valves must be approved by the fire code official.
Section 905.1.1 of the IBC (F). Add a new Section 905.1.1 to the IBC to read as follows:
905.1.1 Delete all references to Class II standpipe systems and replace with Class III standpipe
systems.
Section 905.3.4 of the IBC (F). Delete the exception without substitution.
Section 905.3.9 of the IBC (F). Add a new section 905.3.9 to read as follows:
905.3.9 Additional Standpipe Systems: Additional standpipe systems may be added to new buildings
or structures as deemed necessary by the Code Official.
Section 905.4 of the IBC (F). Amend section 905.4 by deleting #1 and replace with:
1. In every required interior exit stairway, a hose connection shall be provided for each story above
and below grade plane. Hose connections shall be located at intermediate landings between stories,
unless otherwise approved by the fire code official.
Section 906.1 of the IBC (F). Delete the exceptions 1 and 2 without substitution.
Section 906.3 of the IBC (F). Add a sentence to the end of the section to read as follows:
The minimum rating of any required portable fire extinguisher for Class A, Class B, or Class C
hazard shall be 2-10 B C
Section 907.1.4 of the IBC (F). Add a new section 907.1.4 to read as follows:
907.1.4 Fire alarm control panels and Fire alarm annunciator panels. Installation of fire alarm control
panels and fire alarm annunciator panels shall be installed in accordance with section 907.1.4.1
through 907.1.4.5.
12
Ordinance No.
Page 13
Section 907.1.4.1 of the IBC (F). Add a new section 907.1.4.1 to read as follows:
907.1.4.1 Fire Alarm Panel Height: Installation of fire alarm panels shall not exceed 6 feet in height
measured from the floor to the top of the panel. Exception: Panel height may be altered by the fire
code official.
Section 907.1.4.2 of the IBC (F). Add a new section 901.1.4.2 to read as follows:
901.1.4.2 Number of Fire Alarm Control Panels in Buildings: Only one listed fire alarm control panel
shall be allowed per building and shall lock in the alarm until the system is reset and shall not be
canceled by the operation of an audible - alarm silencing switch. This control panel shall only receive
alarm signals from fire protection equipment.
Section 907.1.4.3 of the IBC (F). Add a new section 907.1.4.3 to read as follows:
907.1.4.3 Combination Fire/Security Alarm System Panels. A listed combination fire/security alarm
system panel that meets all the requirements of this code and amendments may be permitted by
approval of the fire code official. The fire/security panel shall be capable of providing a signal that can
differentiate between the fire and security alarm.
Section 907.1.4.4 of the IBC (F). Add a new section 907.1.4.4 to read as follows:
907.1.4.4 Password/PIN Protection Prohibited: Fire alarm control panels and/or fire alarm annunciator
panels that require a password/PIN to silence an alarm/supervisory/trouble signal and/or to reset an
alarm/supervisory/trouble signal shall be prohibited.
Section 907.1.4.5 of the IBC (F). Add a new section 907.1.4.5 to read as follows:
907.1.4.5 Fire Alarm Annunciator Panels: The fire code official can require the addition of fire alarm
annunciator panels based on the size of building and access to the building. These panels shall meet
the requirements of Sections 907.1.4 and 907.2.
Section 907.2 of the IBC (F). Delete section 907.2 and replace with:
907.2 Where required - new buildings and structures. An approved and addressable manual,
automatic, or manual and automatic fire alarm system installed in accordance with the provisions of this
code and NFPA 72 shall be provided in new buildings and structures in accordance with Sections
907.2.1 through 907.2.23 and provide occupant notification in accordance with 907.5 unless other
requirements are provided by another section of this code. Not fewer than one manual fire alarm box
shall be provided in an approved location to initiate a fire alarm signal for fire alarm system employing
automatic fire detectors or water-flow devices. Where other sections of this code allow elimination of
fire alarm boxes due to sprinklers, a single fire alarm box shall be installed.
Exceptions:
1) The manual fire alarm box is not required for fire alarm systems dedicated to elevator recall control
and supervisory service.
2) The manual fire alarm box is required for Group R-2 occupancies to provide a means for fire watch
personnel to initiate an alarm during a sprinkler system impairment event. The manual fire alarm box
shall not be located in an area that is accessible to the public.
3) Multi-tenant buildings required to have a manual/automatic fire alarms system shall install one
manual pull station per tenant space.
4) Visual notification appliances are not required within self-storage units.
13
Ordinance No.
Page 14
Section 907.2.1.3 of the IBC [F]. Add a new section 907.2.1.3 to read as follows:
Group A Occupancies. In Group A occupancies, the activation of the fire alarm or fire sprinkler system,
shall automatically shut down or stop music, sound systems, conflicting or confusing sounds and visual
distractions and initiate illumination of all the means of exit egress components.
Section 907.2.9.1 [F] Delete exception 2 without substitution.
Section 907.2.11.2 of the IBC (F). Modify 907.2.11.2 by adding a fourth location requirement as
follows:
4. Supervised smoke alarms shall be installed in all common corridors and at the top and bottom
of all stairway enclosures in Groups R-2, R-4 and I-1 occupancies. In corridors, detectors shall be
located within fifteen (15) feet of the end of the corridor and in such a way that one detector is
located for each thirty (30) feet of corridor length or spaced as allowed by the code.
Section 907.2.13.2 of the IBC (F). Delete 907.2.13.2 without substitution.
Section 907.4.2 of the IBC (F). Modify 907.4.2 by adding a sentence to the end of the section to read
as follows:
Where, in the opinion of the code official, manual fire alarm boxes may be used to cause false
fire alarms, the code official is authorized to modify the requirements for manual fire alarm boxes.
Section 907.6.3 of the IBC (F). Delete 907.6.3 and replace with:
907.6.3 Initiating device identification. The fire alarm system shall identify the specific initiating device
with an alphanumeric address description showing location, type of device, and status including
indication of normal, alarm, trouble, and supervisory, as appropriate. Alphanumeric descriptions and
locations shall be reported to the emergency communications center upon activation of an alarm
condition as specified by the fire code official.
Exception:
1. Special initiation devices that do not support individual device identification.
Section 907.6.4 of the IBC (F). Modify 907.6.4 by deleting the exception and inserting in lieu thereof
the following exception:
Exception: Automatic sprinkler system zones shall not exceed the area permitted by NFPA 13
and shall provide a sprinkler control valve and waterflow device for each normally occupied floor.
Section 907.6.4.3 of the IBC (F). Add a new section 907.6.4.3 to read as follows:
Section 907.6.4.3 Zone and address location labeling. Fire alarm and/or annunciator panels shall
have all zones and address points plainly and permanently labeled as to their location on the outside
of the panel or on an easily readable map of the building if no display is present.
Section 907.6.6 of the IBC (F). Delete 907.6.6 and replace with:
907.6.6 Monitoring. Fire alarms required by this chapter, the International Building Code, or the Code
Official, an approved UL listed Central Station service in accordance with NFPA 72 shall monitor fire
alarm systems to provide for the immediate and automatic notification to the emergency
communications center. Each initiating device shall report an address point and an alpha/numeric
14
Ordinance No.
Page 15
descriptor showing location, type of device and status including indication of normal, alarm, trouble and
supervisory status, as appropriate. Alpha/numeric descriptor shall be required to be reported to the
emergency communications center upon activation of alarm conditions as specified by the fire code
official.
Exception: Monitoring by a supervising station is not required for:
1. Single- and multiple-station smoke alarms required by Section 907.2.11.
2. Smoke detectors in Group 1-3 occupancies.
3. Automatic sprinkler systems in one- and two-family dwellings
4. Fire alarm systems in one- and two-family dwellings
Section 907.7.4 of the IBC (F). Add a new section 907.7.4 to read as follows:
907.7.4 Device/Zone Map. An easily readable fire alarm device and/or zone map of the building shall
be permanently mounted in or near the fire alarm control panel and documentation cabinet showing the
location of all initiating devices when required by the fire code official.
Section 907.9 of the IBC (F). Add a new Section 907.9 as follows:
907.9 Approved hold open devices. When installed in buildings that have a fire alarm system and /or
sprinkler system, all approved hold open devices shall release upon activation of the fire alarm and/or
sprinkler water-flow activation.
Section 912.4.1 of the IBC (F). Delete the section 912.4.1 and replace with:
Section 912.4.1 Locking fire department connection caps. Locking fire department connection caps
approved by the fire department are required for all new construction that have a water-based fire
protection system and existing structures that have a water-based fire protection system shall be
required immediately after conducting the five-year obstruction and maintenance testing, or if one or
more of the fire department caps are missing.
Section 912.7 of the IBC (F). Add a new section 912.7 to read as follows:
907.7 Fire Department Connection Height. The fire department connection shall be located not less
than 18 inches from the bottom of the cap(s) and not more than 3 feet from the top of the cap(s)above
the level of the adjacent grade or access level. Deviation from this height may be granted by the Code
Official for just cause.
Section 912.8 of the IBC (F). Add a new section 912.8 to read as follows:
912.8 Size. Minimum fire department connection size shall be 2'/z" inch National Standard Thread
siamese connection.
Section 1011.3 of the IBC. Modify 1011.3 by adding a third exception as follows:
Exception:
3. Stairs within individual dwelling units of residential Group R occupancies that existed prior to
8/28/02 (adoption of the 2000 IRC) are permitted a 78-inch (6'-6") headroom clearance.
Section 1023.4 of the IBC. Modify 1023.4 by adding a fourth unnumbered paragraph as follows:
Fire door assemblies that provide access to a non-pressurized interior exit of R-2 occupancies shall
also be automatic closing by actuation of a smoke detector.
Section 1030.2 of the IBC (F). Modify 1030.2 by adding a new exception as follows:
EXCEPTION:
15
Ordinance No.
Page 16
1)The main entrance/exit of A-2 occupancies shall be of a width that accommodates not less than
two-thirds of the total occupant load
Section 1031.2 of the IBC. Modify 1031.2 by deleting the exceptions and inserting in lieu thereof the
following:
EXCEPTIONS:
1. The emergency escape and rescue opening is permitted to open onto a balcony within an atrium
in accordance with the requirements of Section 404 provided the balcony provides access to an
exit and the dwelling unit or sleeping room has a means of egress that is not open to the atrium.
2. Regardless of what Tables 1006.3.4(1) and 1006.3.4(2) allow, all group R-2 occupancies other
than hotels and motels must be provided with emergency escape,& rescue openings.
3. Emergency escape and rescue openings are not required from basements or sleeping rooms
that have an exit door or exit access door that opens directly into a public way or to a yard, court
or exterior exit balcony that opens to a public way.
Section 1031.7 of the IBC. Add a new Section 1031.7 to read as follows:
1030.7. Emergency escape windows under decks, porches and cantilevers shall be fully
openable and provide a path not less than 36 inches in height and 36 inches in width to a yard or court.
Chapter 11 of the IRC. Delete Chapter 11 in its entirety and insert in lieu thereof the following:
Chapter 11 Energy Efficiency, Section N1101. Energy efficiency for the design and construction
of building regulated by this code shall be as required by 661-303 of the Iowa State Administrative
Code.
Chapter 11 of the IBC. Delete Chapter 11' in its entirety and insert in lieu thereof the following:
Chapter 11 Accessibility, Section 1101. Buildings or portions of buildings shall be accessible to
persons with disabilities as required by 661-302 of the Iowa State Administrative Code.
Section 1209.2 of the IBC. Modify 1209.2 by adding a second unnumbered paragraph as follows:
The opening shall be located in a corridor, hallway, or other readily accessible location. The opening
shall not be located in a closet, bathroom, mechanical room, laundry room, or similar room or location.
Attics with a maximum vertical height of less than thirty inches need not be provided with access
openings.
Chapter 13 of the IBC. Delete Chapter 13 in its entirety and insert in lieu thereof the following:
Chapter 13 Energy Efficiency, Section 1301. Energy efficiency for the design and construction of
building regulated by this code shall be as required by 661-303 of the Iowa State Administrative
Code.
Section 1612.2 of the IBC. Delete 1612.2 of the IBC and insert in lieu thereof the following:
1612.2 Design and Construction. The design and construction of buildings and structures located in
flood hazard areas, shall be in accordance with Chapter 5 of ASCE 7, ASCE 24 and Title 14, Chapter
5 Article J Flood Plain Management Standards in the City Code.
Section 1612.3 of the IBC. Amend 1612.3 by inserting:
Jurisdiction: City of Iowa City, Iowa
Date: February 16, 2007
Section 1705.18 of the IBC. Delete 1705.18 and insert in lieu thereof the following:
1705.18 Fire-resistant penetrations and joints. In high-rise buildings, in buildings assigned a Risk
Category III or IV, or Group R occupancies over 3 stories in height, special inspections for through
penetrations, membrane penetration firestops, fire-resistant joint systems and perimeter fire
containment systems that are tested and listed in accordance with Sections 714.4.1.2, 714.5.1.2,
715.3.1 and 715.4 shall be in accordance with Section 1705.18.1 or 1705.18.2.
16
Ordinance No.
Page 17
Part V Mechanical, Chapters 12 through 23 inclusive of the IRC. Delete Part V Mechanical Chapters
12 through 23 inclusive and insert the following:
Part V Mechanical, Chapter 12
Section M1201 GENERAL
M1201.1 Mechanical systems shall comply with the Iowa State Mechanical Code.
Administrative Provisions. The Mechanical Code shall be administered in accordance with
administrative provisions in chapter 1 of this code as amended.
Part VI Fuel Gas, Chapter 24 of the IRC. Delete Part VI Fuel Gas Chapter 24 and insert the
following:
Part VI Fuel Gas, Chapter 24
G2401 GENERAL
G2401.1 Fuel Gas systems shall comply with the Iowa State Plumbing Code.
Administrative Provisions. The Plumbing Code shall be administered in accordance with
administrative provisions in chapter 1 of this code as amended.
Part VII Plumbing, Chapters 25 through 33 inclusive of the IRC. Delete Part VII Plumbing Chapters
25 through 33 inclusive and insert the following:
Part VII Plumbing, Chapter 25
P2501 GENERAL
P2501.1 Plumbing systems shall comply with the Iowa State Plumbing Code.
Administrative Provisions. The Plumbing Code shall be administered in accordance with
administrative provisions in chapter 1 of this code as amended.
Chapter 27 of the IBC. Amend Section 2701 as follows:2701 GENERAL
2701.1 Electrical systems shall comply with the Iowa State Electrical Code.
Administrative Provisions. The Electrical Code shall be administered in accordance with administrative
provisions in chapter 1 of this code as amended and Appendix K as amended.
Chapter 28 of the IBC. Delete chapter 28 and insert the following:
Chapter 28 Mechanical Systems
2801.1 Mechanical systems shall comply the Iowa State Mechanical Code with the following
amendments:
Administrative Provisions. The Mechanical Code shall be administered in accordance with
administrative provisions in chapter 1 of this code as amended.
2801.2 Commercial Kitchen Hood Exhaust Termination:
In addition to the code requirements for commercial kitchen hood exhaust termination locations, the
following shall apply:
1. For new construction, change in occupancy or change in use, that requires a new commercial
kitchen hood or revisions to an existing commercial kitchen hood, the new or existing commercial
kitchen hood exhaust duct shall terminate as follows: Above the roof level without passing through an
exterior wall; or
2. Through an alley facing exterior wall provided the termination is above the roof level; or
3. To an alley right of way per 3202.3.2 of the International Building Code.
Chapter 29 of the IBC. Delete Chapter 29 and insert the following:
Chapter 29 Plumbing Systems
17
Ordinance No.
Page 18
2901.1 Plumbing systems shall comply with the Iowa State Plumbing Code.
Administrative Provisions. The Plumbing Code shall be administered in accordance with
administrative provisions in chapter 1 of this code as amended.
Section 3002.4 of the IBC. Delete 3002.4 and insert in lieu thereof the following:
3002.4 Elevator car to accommodate ambulance stretcher.
In buildings four or more stories above, or four or more stories below, grade plane, at least one
elevator shall be provided for fire department emergency access to all floors. The elevator car shall
be of such a size and arrangement to accommodate an ambulance stretcher 24 inches by 84 inches
(610 mm by 2134 mm) with not less than 5-inch (127 mm) radius corners, in the horizontal, open
position and shall be identified by the international symbol for emergency medical services (star of
life). The symbol shall not be less than 3 inches (76 mm) high and shall be placed inside on both
sides of the hoistway door frame.
Part VIII Electrical, Chapters 34 through 43 inclusive of the IRC. Delete Part VIII Electrical
Chapters 34 through 43 inclusive of the IRC and insert the following:
Part VIII Electrical, Chapter 34
E3401 GENERAL
E3401.1 Electrical systems shall comply with the Iowa State Electrical Code.
Administrative Provisions. The Electrical Code shall be administered in accordance with administrative
provisions in chapter 1 of this code as amended and Appendix K of the IBC as amended.
Appendix K of the IBC.
Section K103.2 of the IBC. Work exempt from permit. Delete K103.2 and insert in lieu thereof the
following:.
K103.2 Work exempt from permit. See section 105.2 in both the IRC and IBC.
Section K106.5 of the IBC. Add a new Section K106. 5 as follows:
K106. 5 Energy Connections; An electrical system or equipment regulated by this code for which a
permit is required shall not be connected to a source of energy or power until approved by the building
official.
Section K106.6 of the IBC. Add a new Section K106. 6 as follows:
K106. 6 Temporary Energy Connections. The building official may authorize the temporary connection
of the electrical system or equipment to the source of energy or power for the purpose of testing the
equipment, or for use under a temporary certificate of occupancy.
Appendix AF of the IRC. Delete AF104 of the IRC entirely.
Appendix AJ of the IRC.
Section AJ102.4 of the IRC. Delete AJ102.4 and insert in lieu thereof the following:
AJ102.4 Replacement windows and doors. Regardless of the category of work, where an existing
window or door, including the sash and glazed portion, or safety glazing is replaced, the replacement
window, door or safety glazing shall comply with the requirements of Sections AJ102.4.1 through
AJ102.4.3, as applicable.
Section AJ102.4.1 of the IRC. Delete AJ102.4.1 and insert in lieu thereof the following:
AJ102.4.1 Energy efficiency. Replacement windows or doors shall comply with the requirements of
Chapter 11.
Section AJ102.4.4 of the IRC. Delete AJ102.4.4 entirely.
18
Ordinance No.
Page 19
Section AJ109.7 of the IRC. Delete AJ109.7 and insert in lieu thereof the following:
AJ109.7 Ceiling height. Habitable spaces created in existing basements or attics shall have ceiling
heights of not less than 6 feet, 8 inches (2032 mm), except that the ceiling height at obstructions shall
be not less than 6 feet 4 inches (1930 mm) from the basement or attic floor. Existing finished ceiling
heights in nonhabitable spaces in basements or attics shall not be reduced. .
Section AJ109.8.1 of the IRC. Delete AJ109.8.1 and insert in lieu thereof the following:
AJ109.8.1 Stair width. Existing basement and attic stairs and handrails not otherwise being altered or
modified shall be permitted to maintain their current clear width at, above and below existing handrails.
Section AJ109.8.2 of the IRC. Delete AJ109.8.2 and insert in lieu thereof the following:
AJ109.8.2 Stair headroom. Headroom height on existing basement or attic stairs being altered or
modified shall not be reduced below the existing stairway or attic finished headroom. Existing basement
or attic stairs not otherwise being altered shall be permitted to maintain the current finished headroom.
Section AJ109.8.3 of the IRC. Delete AJ109.8.3 and insert in lieu thereof the following:
AJ109.8.3 Stair landing. Landings serving existing basement or attic stairs being altered or modified
shall not be reduced below the existing stairway landing depth and width. Existing basement or attic
stairs not otherwise being altered shall be permitted to maintain the current landing depth and width.
17-1-4: Penalties for violations: Violation of this chapter shall be a municipal infraction punishable
by a penalty as provided for in subsection 1-4-2D of the City Code.
Except as provided herein, any reference to the "Plumbing Code," the "Electrical Code," or the
"Mechanical Code" is deleted and replaced with "Building Code."
2. Title 17, entitled "Building and Housing," Chapter 12, entitled
"Appeals," Section 2, entitled "Appeals Procedure," Subsection D is amended by adding the
underscore text and deleting the strike-through text as follows:
Hearing: The person shall be advised in writing of the time and place at least three (3) calendar days
prior to the hearing. At the hearing, the person shall have an opportunity to be heard the board shall
review all applicable evidence presented regarding the subject appeal.
Section II. Repealer. All ordinances and parts of ordinances in conflict with the provision of this
Ordinance are hereby repealed.
Section III. Severability. If any section, provision or part of the Ordinance shall be adjudged to be invalid
or unconstitutional, such adjudication shall not affect the validity of the Ordinance as a whole or any
section, provision or part thereof not adjudged invalid or unconstitutional.
Section IV. Effective Date. This Ordinance shall be in effect after final passage, approval and
publication as provided by law.
Passed and approved this day of , 2023.
Mayor
Attest:
City Clerk
Approved by,
G
City Attor y's Office
(Sue Dulek—05/30/2023)
19
Ordinance No.
Page 20
It was moved by and seconded by that the Ordinance
as read be adopted, and upon roll call there were:
Ayes: Nays: Absent:
Alter
Bergus
Dunn
Harmsen
Taylor
Teague
Thomas
First Consideration 06/06/2023
Voteforpassage: AYES: Alter, Bergus, Dunn, Harmsen, Taylor, Teague, Thomas
NAYS: None ABSENT: None
Second Consideration
Vote for passage:
Date published
•
20
=111101111=1'ITT :a:a
CITY OF IOWA CITY
ca 7R COUNCIL ACTION REPORT
June 6, 2023
Ordinance amending Title 7, Chapter 1, Fire Prevention and Protection, by adopting the 2021
edition of the International Fire Code to regulate and govern the safeguarding of life and
property from fire, explosion, life safety risks, or health hazards.
Prepared By: Danielle Sitzman, Development Services
Reviewed By: Troy Roth, Fire Marshall
Sue Dulek, First Assistant City Attorney
Fiscal Impact: None
Staff Recommendation: Approval
Commission Recommendations: The Board of Appeals recommended approval of the
proposed ordinance at its meeting May 1, 2023.
Attachments: Memo to Board of Apeals
Board of Appeals 5-1-23 minutes DRAFT_.docx
Ordinance
Executive Summary:
State law requires a public hearing on the adoption of a model code. Staff is recommending
adoption of the 2021 edition of the International Fire Code (IFC) along with local
amendments. A copy of the ordinance and the IFC are on file in the City Clerk's office.
Background / Analysis:
A description of the notable changes are included in a memorandum from Troy Roth, Fire
Marshall to the Board of Appeals dated April 25, 2023.
Memorandum
Iowa City Fire Department
410 E. Washington Street — Iowa City, IA 52240-1821
Phone: 319.356.5260 www.icgov.org
Date: April 25, 2023
To: Board of Appeals
From: Troy Roth, Fire Marshal
Re: Notable changes to the 2021 International Fire Code local amendments
The fire department presents for your review, notable changes to the 2018 International Fire
Code (IFC).
308.3 Local Amendment. Open Flames. Add number 4: Outdoor assembly spaces
are allowed to be provided with natural gas fueled fire pit appliances complying
with the applicable adopted codes and manufacturer's listing.
321 Addition. Artificial Combustible Vegetation On Roofs And Near Buildings.
The trend of rooftop assembly areas has resulted in artificial vegetation
decorations posing increased fire threat.
405 Modification. Emergency Evacuation Drills. This change increases the
frequency and participation of evacuation drill. E occupancies are increased to
monthly. Iowa City amends this to follow state code requiring four drills per
school year, two in the fall semester and two in the spring semester.
503.2.9 Local amendment. Add a new section to read as follows: Thickness. Fire
apparatus access roads shall be constructed of Portland cement concrete
conforming to the specifications of the Iowa Department of Transportation C-3 or
M-3 mixes. The concrete access road shall be a minimum of 7 inches thick over
compacted soil.
506.1 Local amendment. Add a sentence to the end of the section to read as follows: An
approved key box shall be installed in an approved location on all new
construction.
Exception: Group R-3
508 Modification. Fire Command Center. Command center requirements were
added to large factories and warehouses where they had generally only been
required in high-rises.
510 Modification. Emergency Responder Communication Coverage — Signals.
Clarified testing criteria for radio signal strength as well as requiring more area
coverage.
610 Addition. Clothes Dryer Exhaust Systems. This new section regulates the
installation and cleaning of dryer vents due to nation fire cause statistics.
808.5 Addition. Play Structures. Play structures installed at the time of construction
are regulated by the International Building Code (IBC). This new section directs
designers and installers of play structures that are added to existing buildings to
follow the IBC requirements.
901 Modification. Life Safety Systems. Essentially a verbiage change from fire
protection systems to life safety systems. An example is CO detection.
903.2.10 Modification. Group S-2 Parking Garages. Open parking ramps exceeding
48,000 square feet now require sprinkler systems.
903.2.10.02 Addition. Mechanical -Access Parking Garages. New section regulating
mechanical parking structures.
903.3.1.2 Modification. NFPA 13R Sprinkler Systems. The maximum allowable height
to allow 13R to be used rather than 13 is lowered to 30 feet above lowest fire
department access. This will increase the likelihood of sprinklered attics.
903.5.2 Local amendment. Add a new section to read as follows: Forward Flow Testing.
Automatic sprinkler systems shall be provided with an external outlet to perform forward
flow testing as required by NFPA 25. Outlet shall be supervised, signed as testing, and
have male threads.
903.7 Local amendment. Section 903.7 Add a new section to read as follows: Zones.
Automatic sprinkler system zones shall not exceed the area permitted by NFPA 13 or
NFPA 13R and shall provide a sprinkler control valve and waterflow device for each
normally occupied floor. The location of sprinkler control valves must be approved by
the fire code official.
905.4 Local amendment. Requirement #1 Delete the section and replace with: In every
required interior exit stairway, a hose connection shall be provided for each story above
and below grade plane. Hose connections shall be located at intermediate landing
between stories, unless otherwise approved by the fire code official.
907.4 Modification. Low -Frequency Alarms in Sleeping Rooms. Alarm notification
in sleeping room will now be required to be 520 Hz. Studies have shown the low
frequency sound is six times more effective at waking at -rink populations than the
current 3KHz tone.
912.4.1 Local amendment. Delete the section and replace with: Locking fire department
connection caps. Locking fire department connection caps approved by the fire
department are required for all new construction that have a water-based fire
protection system and existing structures that have a water-based fire protection
system shall be required immediately after conducting the five-year obstruction
and maintenance testing, or if one or more of the fire department caps are missing.
1009.2.1 Modification. Elevator Serving Occupied Roof. An occupied roof is now
counted as a story when determining if an elevator is required in a building.
1010.1.1 Modification. Size of Doors. The maximum width of doors (48") is eliminated.
Section 1010. 1.3 still limits the force need to open the to 5lbs, but the door can
now be 12 feet wide for example.
1010.2.8 Modification. Locking arrangements in Educational Occupancies. This
section allows for tighter lockdown options to protect occupants from intruders.
1204 Addition. Portable Generators. Previously generally unregulated, portable
generators are now regulated under this section.
3303.3 Addition. Daily Fire Safety Inspection. Because of the increase of fires in
buildings under construction, the building owner is now responsible to ensure that
a daily fire safety inspection is conducted.
DRAFT
MINUTES
IOWACITYBOARD OFAPPEALS
May 1, 2023 - 4 PM
HELLING CONFERENCE ROOM, CITYHALL
410 E. WASHINGTON STREET
IOWA CITY, IA 52240
MEMBERSPRESENT: Andrea French, Andrew Martin,Thomas McInerney, GT Karr
MEMBERS ABSENT: Jim Walker
STAFF PRESENT: Tim Hennes (Sr. Building Inspector), Sarah Horning (Development
Services Assistant), Troy Roth (Fire Marshal), Sue Dulek (Assistant City
attorney)
RECOMMENDATIONS TO COUNCIL:
Adoption of 2021 International Building and Fire Codes
CALL TO ORDER:
Chair Andrew Martin called the meeting to order at 4 PM
CONSIDERATION OF MINUTES: April 5, 2023 Board of Appeals minutes
MOTION: McInerney moved to approve the minutes from the April 5, 2023 Board of Appeals
meeting. Seconded by French.
VOTE: Motion passed 4-0.
Discussion and possible recommendation to Council regarding the adoption of the
2021 International Buildina and Fire Codes.
DISCUSSION: Martin commented that the new code seems to have been amended to keep
it the way it is now. Tim Hennes agreed and stated that the main difference between the 2018
and 2021 codes is that the new code allows for mass timber construction, which allows for
up to 18 stories be constructed of wood. Hennes also noted that the city's delay in adopting
the new code was due to the discussion of the state legislatures adopting a state building
code, which would have taken building codes out of the hands of the city all together and
since that did not happen, the staff chose to move forward with the adoption of the 2021
codes.
Hennes stated that the city has worked with neighboring jurisdictions (Johnson County, North
Liberty, Coralville & Tiffin) to be consistent with code enforcement and Roth shared that the four
communities are near identical when it comes to the fire code.
MOTION: McInerney moved to recommend to Council to adopt the 2021 International Building
and Fire Codes as amended. Seconded by Karr.
VOTE: Motion passed 4-0.
ADJOURNMENT:
MOTION: McInerney moved to adjourn meeting, French seconded.
VOTE: Motion passed 4-0.
Meeting adjourned at 4:10 PM.
Chairperson, Board of Appeals Date
CI 10
Prepared by: Troy Roth, Fire Marshal, 410 E. Washington Street, Iowa City, IA 52240
Ordinance No. 23-
Ordinance amending Title 7, Chapter 1 , Fire Prevention and Protection, by
adopting the 2021 edition of the International Fire Code to regulate and
govern the safeguarding of life and property from fire, explosion, life safety
risks, or health hazards.
Wherefore, the Iowa City Fire Code codified in Title 7, Chapter 1 of the Iowa City Code, consists
of the 2018 edition of the International Fire Code along with local amendments; and
Whereas, the International Code Council publishes updated codes every three years, and it is in
the best interest of the City to adopt the 2021 edition of the International Fire Code along with
local amendments.
Now, therefore be it ordained by the City Council of the City of Iowa City, Iowa:
Section I. Amendments.
1. Title 7, Section 1, entitled, "Fire Code Adopted," is hereby deleted and the following new
Section 1 is inserted in lieu thereof:
That a certain document, one (1) copy of which is on file in the office of the City Clerk of the
City of Iowa City, being marked and designated as the International Fire Code, 2021 edition,
including errata and Appendix Chapters B, C, D, E, F, G, H, I, J, K, and N as published by the
International Code Council, be and is hereby adopted as the Fire Code of the City of Iowa City,
in the State of Iowa regulating and governing the safeguarding of life and property from fire and
explosion hazards arising from the storage, handling and use of hazardous substances,
materials and devices, and from conditions hazardous to life or property in the occupancy of
buildings and premises as herein provided, providing for the issuance of permits and each, and
all of the regulations, provisions, penalties, conditions and terms of said Fire Code on file in the
office of the City Clerk are hereby referred to, adopted and made a part hereof, as if fully set out
in this ordinance, with the additions, insertions, deletions and changes, prescribed in the
following sections of this ordinance.
2. Title 7, Section 2, entitled "Amendments to Fire Code," is deleted in its entirety and the
following new Section 2 is inserted in lieu thereof:
That the following sections are hereby revised:
Section 101.1 Insert: Iowa City, Iowa
Section 103.1 Insert: Iowa City Fire Department
Section 104.1.1 Add a new section to read as follows: The code official and members of the fire
prevention bureau shall have the powers of a peace officer in performing their duties under this
Code.
Section 104.1.2 Add a new section to read as follows: The Fire Chief may appoint and
designate such members of the Fire Department as fire/police investigators upon being certified
Ordinance No.
Page 2
by the Iowa Law Enforcement Academy. Fire/police investigators shall have the powers of a
peace officer in performing their duties under this Code, including full powers of arrest to
effectuate their duties of enforcing city ordinances and state statutes. Notwithstanding his/her
status as a peace officer, a fire/police investigator shall be subject to the rules and regulations of
the Iowa City Fire Department for all purposes and shall perform such functions as the Fire
Chief shall assign.
Section 104.12 Add a new section to read as follows: The code official is authorized to order an
operation or use stopped, or the evacuation of any premises, building, or vehicle or portion
thereof which has or is a fire, life safety or health hazard.
Section 105.2 Add a sentence to the end of the section to read as follows: Application for an
operational permit shall be submitted with all required information not less than 14 days prior to
the event requiring a permit.
Section 105.5 Add a sentence to the end of the section to read as follows: The fire code official
at their discretion shall send plans for operational permits requests to an outside agency for
review. The fire code official shall choose the plans review agency. The applicant shall pay all
fees associated with the plan review directly to the outside agency. The permit shall not be
issued until the review fees have been paid.
Section 105.6 Add a sentence to the end of the section to read as follows: The fire code official
at their discretion may send plans for operational permits requests to an outside agency for
review. The fire code official shall designate the plans review agency. The applicant shall pay all
fees associated with the plan review directly to the outside agency. The permit shall not be
issued until the review fees have been paid.
Section 111. Delete in its entirety and insert in lieu thereof: See Title 17, Chapter 12 of this
Code.
Section 112.4 Delete the section and replace with: Persons who shall violate a provision of this
code or shall fail to comply with any of the requirements thereof or who shall erect, install, alter,
repair or do work in violation of the approved construction documents or directive of the fire
code official, or of a permit or certificate used under provisions of this code, shall be guilty of a
simple misdemeanor or municipal infraction, as prescribed in Title 1, Chapter 4 of this Code.
Each day that a violation continues after due notice has been served shall be deemed a
separate offense.
Section 202 Add a new definition to read as follows: Crowd Manager. Crowd Manager is
responsible for safe crowd movement during daily activities and special events, means of
egress, assisting venue occupants, and overseeing emergency response and evacuation plans.
Section 202 Add a new definition to read as follows: Emergency Communications Center. The
Johnson County Joint Emergency Communications Center. (JCJECC)
Section 202 Add a sentence to the end of Fire Lane definition to read as follows: See City Code
9-4-13 for additional rules and regulations.
Section 307 See also 6-6 of this Code.
Ordinance No.
Page 3
Section 307.1.2 Add a new section to read as follows: Hours of operation. Outdoor burning
allowed by code is permitted between the hours of 7:00 AM and 11:00 PM or as permitted and
approved by the fire code official.
Section 308.3 Add number 4: Outdoor assembly spaces are allowed to be provided with natural
gas fueled fire pit appliances complying with the applicable adopted codes and manufacturer's
listing.
Section 401.9 Add a new section to read as follows: Building evacuation. Upon activation of
the building fire alarm system or upon notification by other means of detecting and reporting
unwanted fire, all building occupants shall promptly evacuate the building. Building employees
and tenants shall implement the appropriate emergency plan and procedures.
Exception: When the emergency evacuation plan, as approved by the fire code official,
does not require the immediate total evacuation of the building.
Section 402.1 Add a new definition to read as follows: Crowd Manager. Crowd Manager is
responsible for safe crowd movement during daily activities and special events, means of
egress, assisting venue occupants, and overseeing emergency response and evacuation plans.
Section 403.11.3 Add new sentences to read as follows: A-2 Occupancy Crowd Managers.
Group A-2 occupancies shall be provided with a minimum of one (1)trained crowd manager
anytime occupancy reaches 50 or more. Where the occupant load exceeds 250, additional
trained crowd managers shall be provided at a ratio of one (1) crowd manager for every 250
occupants. The crowd manager shall annually receive training approved by the fire code official
in crowd management techniques.
Section 405.3 Add to the end of the section as follows: Fire and evacuation drills in Group E
occupancies shall be conducted in accordance with Section 100.31 of the Code of Iowa.
Emergency evacuation/fire drills shall be conducted at least four times a year. Not less than two
drills shall be conducted between July 1 and December 31 each year and not less than two
drills shall be conducted between January 1 and June 30 of each year. The Iowa City Fire
Department shall conduct one of the two drills during July 1 and December 31 and one of the
two drills during January 1 and June 30 of each year. Fire drills in Group R, Division 2,
Fraternities and Sororities, shall be conducted once per academic semester.
Section 405.3 Table Amend frequency of Group E Occupancy to footnote d and add footnote d as
follows: d. Group E occupancies shall conduct fire and evacuation drills in accordance with Section
405.3.
Section 503.2 Delete this section and replace with: Specifications. Fire apparatus access roads
shall be installed and arranged in accordance with sections 503.2.1 through 503.2.9.
Section 503.2.9 Add a new section to read as follows: Thickness. Fire apparatus access roads
shall be constructed of Portland cement concrete conforming to the specifications of the Iowa
Department of Transportation C-3 or M-3 mixes. The concrete access road shall be a minimum
of 7 inches thick over compacted soil.
Section 505.1. Add table.
Minimum Height and Stroke Width a,b,c,d
Distance from the centerline of the Public Way (ft) Minimum Height (in) Minimum Stroke Width (in)
Less than 100 4 1/2
Ordinance No.
Page 4
100 199 6 3/4
200 299 8 1
For each additional 100 Increase 2 Increase 1/2
a) Exterior suite identification, minimum height shall be 4 inches and stroke width shall be
1/z inch.
b) Interior suite identification, minimum height shall be 3 inches and stroke width shall be
inch.
c) Measurements to determine the minimum number or letter size shall be measured from
the approved
address location to the center line of the street for which the premise is addressed.
d) Minimum height and minimum stroke may be increased by the Code Official.
Section 505.3 Add a new section to read as follows: Addresses for Buildings under
Construction. Upon permit issuance, all new commercial and residential buildings under
construction shall have plainly visible addresses from the street. Additional address signage
may be required at the discretion of the code official.
Section 506.1 Add a sentence to the end of the section to read as follows: An approved key box
shall be installed in an approved location on all new construction.
Exception: Group R-3
Section 506.1.2 Delete both references to "nonstandardized".
Section 507.3 Delete the section and replace with: Fire flow. Fire flow requirements for buildings
or portions of buildings shall be determined by"Appendix B" of this code.
Section 507.5.1.1 Delete the section and replace with: Fire Sprinkler System & Standpipe
System Support. A fire hydrant shall be located no more than 100 feet from a fire sprinkler or
standpipe system connection on hard surface, located on the same side of the fire department
access road, easily accessible by fire apparatus, and meeting the approval of the Code Official.
Section 507.5.7 Add a new section to read as follows: Fire Hydrant Installation
Section 507.5.7.1 Add a new section to read as follows: Fire hydrant outlet direction: All fire
hydrants shall be positioned so that the four and one-half (4 1/2) inch connection is facing the
street or driveway accessible to fire department apparatus or as specified and required by the
local water jurisdiction.
Section 507.5.7.2 Fire hydrants threads: All new fire hydrants within the limits of the city of Iowa
City shall have National Standard Threads (NST) on the two and one-half (2 1/2) inch
connections and the four and one-half (4 1/2) inch connection will have a Storz connection as
specified and required by the local water jurisdiction.
Section 507.5.7.3 Flow: The minimum flow requirements for a water main serving a fire hydrant
is the rate of water flow, at a residual pressure of twenty pounds per square inch (20psi) and for
a specified duration, as specified in appendix B of this code or as specified and required by the
local water jurisdiction.
Section 507.5.7.4 Add a new section to read as follows: Fire hydrant height: Fire hydrants shall
be installed a minimum of sixteen (16) inches from the nominal ground level to the center of the
lowest water outlet or as specified and required by the local water jurisdiction.
Ordinance No.
Page 5
Section 510.1 Delete exception 1 & 2.
Section 604.8. Add a new section to read as follows: Elevator equipment signage. New and
existing buildings with an elevator shall have an approved, visible sign located next to the
elevator key box stating the location of the elevator equipment room and elevator power shut-
off.
Section 604.6.1 Add a sentence to the end of the section to read as follows: The Fire Code
Official may require an approved elevator key box in an approved location to secure required
elevator keys.
Section 606.4 Delete the last sentence and replace with: Movement of new and existing cooking
appliances with caster(s) under a Type 1 hood shall be limited by an approved floor mounted
restraining device and flexible gas connector installed in accordance with the connector and
appliance manufacturer's instructions.
Section 606.5 Add a new section to read as follows: Required separation. All deep-fat fryers
shall be installed with at least 16- inch space between the fryer and surface flames from
adjacent cooking equipment. Where a steel or tempered glass baffle plate is installed at a
minimum 8-inch height between the fryer and surface flames to the adjacent appliance, the
requirement for a 16-inch space shall not apply.
Section 803.16 Add a new section to read as follows: Maintenance. The interior finish of
buildings shall be maintained in accordance with the conditions of original approval. Any
change to the interior finish that is regulated by the provisions of this code or the building code
shall be made in accordance with all applicable requirements.
Section 807.5.2.1 Delete exception 2.
Section 807.5.5.1 Delete exception 2.
Section 901.2 (a) Add a new section to read as follows: Water based fire protection systems.
Working plans submitted to the fire department for water-based fire protection systems shall be
stamped and approved by a qualified person to be in compliance with applicable NFPA
standards and the Iowa City Fire Code. Any changes to the working plans shall be approved by
a qualified person. A qualified person shall have a minimum National Institute for Certification in
Engineering Technologies [NICET] Level III certification for Automatic Sprinkler System Layout
OR be a licensed engineer with experience in life safety system design. Other qualifications
may be approved by the code official.
Section 901.2 (b) Add a new section to read as follows: Fire alarm systems. Working plans
submitted to the fire department by a qualified person for fire alarm systems shall be stamped
and approved by a qualified person to be in compliance with applicable NFPA standards and
the Iowa City Fire Code. Any changes to the working plans shall be approved by a qualified
person. A qualified person shall have a minimum National Institute for Certification in
Engineering Technologies [NICET] Level III certification for Fire Alarm Systems OR be a
licensed engineer with experience in life safety system design. Other qualifications may be
approved by the code official.
Section 901.4.7.3. Add a sentence to the end of the section to read as follows: The fire pump
room or automatic sprinkler riser room shall have a supervised room temperature sensor.
Ordinance No.
Page 6
Section 901.4.7.4. Add a sentence to the end of the section to read as follows: Emergency
lighting shall be provided in the fire pump room or automatic sprinkler riser room.
Section 901.4.7.5 Add a new section to read as follows: Additional Requirements. The fire pump
room or automatic sprinkler riser room shall be separated from electrical room and have no
electrical panels inside the rooms other than electrical power required for the use of the fire
alarm and fire protection equipment and have a floor drain. Unless otherwise approved by the
fire code official, the fire sprinkler riser room with one sprinkler riser shall have a minimum area
of sixteen (16) square feet with a minimum dimension of four (4) feet providing at least three (3)
feet clearance in front of the sprinkler, fire alarm control panel and fire pump equipment. If
additional sprinkler risers are installed, the room size shall be increased to provide at least three
(3)feet of clearance in front of each riser.
Section 901.6.3.2 Add a new section to read as follows: Inspection record submission.
Contractors who perform installation, inspection, testing, and/or maintenance services on fire
and life safety systems are required to electronically submit all installation and compliant & non-
compliant inspection reports to the Fire Department via a method approved by the Fire Code
Official within 30 calendar days of the installation/inspection date. Reports submitted after 30
calendar days may incur late fees.
Section 901.7 Add a section to the end of the section to read as follows: A person assigned to
fire watch must walk through the building at least once every 30 minutes checking for fire or
smoke. A fire watch must be continued until the fire alarm system and/ or fire protection system
has been restored to normal operating condition or the building has been evacuated. A
competent adult familiar with the building must conduct the fire watch. If a fire is discovered, 911
shall be called immediately and the building evacuated.
Section 903.3.5.1 Delete this section and replace with: A single domestic and automatic fire
sprinkler system water supply. If the city water provider requires a single domestic and
automatic fire sprinkler system supply, then the water supply shall be split outside of the building
and shall have a shutoff provided for the domestic service after the split outside of the building.
The total domestic demand is required to be added to the fire sprinkler demand.
Section 903.3.5.2 Delete this section.
Section 903.3.5.3 Add a new section to read as follows: Water supply safety margin. The fire
sprinkler system hydraulically calculated demand per NFPA 13 or NFPA 13R including required
hose stream allowances, and domestic water demand if required by section 903.3.5.2, must be
a minimum 10%, but not less than 5 psi below the water supply flow test curve, the flow test
must have been conducted within 90 days of fire sprinkler plan submittal to the city and third
party reviewer (if applicable) or as deemed current and approved by the local water jurisdiction.
The base of riser psi at the time of acceptance test shall also be 10% but not less than 5 psi
above the most demanding hydraulically calculated pressure.
Section 903.4 Delete exception number 5 without substitution. •
Section 903.4.2 Delete the section and replace with: Alarms. An approved weatherproof
horn/strobe device shall be mounted directly above the fire department connection between
seven (7) and ten (10) feet in height above grade. The water-flow alarm device shall be
activated by water flow equivalent to the flow of a single sprinkler of the smallest orifice size
Ordinance No.
Page 7
installed in the system. Approved and supervised audible visual notification appliances shall be
installed on each level of the interior of the building as required by the fire code official and
NFPA 72. Where a fire alarm system is installed, actuation of the automatic sprinkler system
shall actuate the building fire alarm system.
Section 903.5.1 Add a new section to read as follows: Inspector's test valve. An inspector's
test valve is required at the most remote location in each fire sprinkler system or tenant/floor
control valve space, for use at the acceptance test and to remove air from the system after
maintenance work is done on the system.
Section 903.5.2 Add a new section to read as follows: Forward Flow Testing. Automatic
sprinkler systems shall be provided with an external outlet to perform forward flow testing as
required by NFPA 25. Outlet shall be supervised, signed as testing, and have male threads.
Section 903.7 Add a new section to read as follows: Zones. Automatic sprinkler system zones
shall not exceed the area permitted by NFPA 13 or NFPA 13R and shall provide a sprinkler
control valve and waterflow device for each normally occupied floor. The location of sprinkler
control valves must be approved by the fire code official.
Section 904.13.6 Add a new section to read as follows: Ventilation Operation. The ventilation
system shall shut down the make-up air to the hood and continue to exhaust upon activation of
the hood fire extinguishing system. Exception: Section 904.13.6 may be revoked if the fire
extinguishing agent will not perform to specifications due to exhausting requirements.
Section 905.1.1 Add a new section to read as follows: Delete all references to Class II standpipe
systems and replace with Class III standpipe systems.
Section 905.3.4 Delete the exception without substitution.
Section 905.3.9 Add a new section to read as follows: Additional Standpipe Systems: Additional
standpipe systems may be added to new buildings or structures as deemed necessary by the
Code Official.
Section 905.4 Requirement #1 Delete the section and replace with: In every required interior
exit stairway, a hose connection shall be provided for each story above and below grade plane.
Hose connections shall be located at intermediate landing between stories, unless otherwise
approved by the fire code official.
Section 906.1 Delete exceptions 1 & 2 without substitution.
Section 906.3 Add a sentence to the end of the section to read as follows: The minimum rating
of any required portable fire extinguisher for Class A, Class B, or Class C hazard shall be 2-A,
10-B C.
Section 907.1.4 Add a new section to read as follows: Fire alarm control panels and Fire alarm
annunciator panels. Installation of fire alarm control panels and fire alarm annunciator panels
shall be installed in accordance with section 907.1.4.1 through 907.1.4.5.
Section 907.1.4.1 Add a new section to read as follows: Fire Alarm Panel Height: Installation of
fire alarm panels shall not exceed 6 feet in height measured from the floor to the top of the
panel. Exception: Panel height may be altered by the code official.
Ordinance No.
Page 8
Section 907.1.4.2 Add a new section to read as follows: Number of Fire Alarm Control Panels in
Buildings: Only one listed fire alarm control panel shall be allowed per building and shall lock in
the alarm until the system is reset and shall not be canceled by the operation of an audible —
alarm silencing switch. This control panel shall only receive alarm signals from fire protection
equipment.
Section 907.1.4.3 Add a new section to read as follows: Combination Fire/Security Alarm
System Panels. A listed combination fire/security alarm system panel that meets all the
requirements of this code and amendments may be permitted by approval of the fire code
official. The fire/security panel shall be capable of providing a signal that can differentiate
between the fire and security alarm.
Section 907.1.4.4 Add a new section to read as follows: Password/PIN Protection Prohibited:
Fire alarm control panels and/or fire alarm annunciator panels that require a password/PIN to
silence an alarm/supervisory/trouble signal and/or to reset an alarm/supervisory/trouble signal
shall be prohibited.
Section 907.1.4.5 Add a new section to read as follows: Fire Alarm Annunciator Panels: The fire
code official can require the addition of fire alarm annunciator panels based on the size of
building and access to the building. These panels shall meet the requirements of Sections
907.1.4 and 907.2.
Section 907.2 Delete the section and replace with: Where required - new buildings and
structures. An approved and addressable manual, automatic, or manual and automatic fire
alarm system installed in accordance with the provisions of this code and NFPA 72 shall be
provided in new buildings and structures in accordance with Sections 907.2.1 through 907.2.23
and provide occupant notification in accordance with 907.5 unless other requirements are
provided by another section of this code. Not fewer than one manual fire alarm box shall be
provided in an approved location to initiate a fire alarm signal for fire alarm system employing
automatic fire detectors or water-flow devices. Where other sections of this code allow
elimination of fire alarm boxes due to sprinklers, a single fire alarm box shall be installed.
Exceptions:
1) The manual fire alarm box is not required for fire alarm systems dedicated to elevator recall
control and supervisory service.
2) The manual fire alarm box is required for Group R-2 occupancies to provide a means for fire
watch personnel to initiate an alarm during a sprinkler system impairment event. The manual
fire alarm box shall not be located in an area that is accessible to the public.
3) Multi-tenant buildings required to have a manual/automatic fire alarms system shall install
one manual pull station per tenant space.
4) Visual notification appliances are not required within self-storage units.
Section 907.2.1.3 Add a new section to read as follows: Group A Occupancies. In Group A
occupancies, the activation of the fire alarm or fire sprinkler system, shall automatically shut
down or stop music, sound systems, conflicting or confusing sounds and visual distractions and
initiate illumination of all the means of exit egress components.
Section 907.2.9.1 Delete exception 2 without substitution.
Section 907.2.11.2 Modify by adding a fourth location requirement as follows:
Ordinance No.
Page 9
4. Supervised smoke detectors shall be installed in all common corridors and at the top and
bottom of all stairway enclosures in Groups R-2, R-3, R-4, and I-1 occupancies. In
corridors, detectors shall be located within fifteen (15) feet of the end of the corridor and
in such a way that one detector is located for each thirty (30) feet of corridor length or
spaced as allowed by the code.
Section 907.2.13.2 Delete the section without substitution.
Section 907.4.2 Add a sentence to the end of the section to read as follows: Where in the
opinion of the code official manual fire alarm boxes may be used to cause false fire alarms, the
code official is authorized to modify the requirements for manual fire alarm boxes.
Section 907.6.3 Delete this section and replace with: Initiating device identification. The fire
alarm system shall identify the specific initiating device with an alphanumeric address
description showing location, type of device, and status including indication of normal, alarm,
trouble, and supervisory, as appropriate. Alphanumeric descriptions and locations shall be
reported to the emergency communications center upon activation of an alarm condition as
specified by the fire code official.
Exception:
1. Special initiation devices that do not support individual device identification.
Section 907.6.4 Modify by deleting the exception and inserting in lieu thereof: Exception:
Automatic sprinkler system zones shall not exceed the area permitted by NFPA 13 and shall
provide a sprinkler control valve and waterflow device for each normally occupied floor.
Section 907.6.4.3 Add a section to read as follows: Zone and address location labeling. Fire
alarm and/or annunciator panels shall have all zones and address points plainly and
permanently labeled as to their location on the outside of the panel or on an easily readable
map of the building, if no display is present.
Section 907.6.6 Delete the section and replace with: Monitoring. Fire alarms required by this
chapter, the International Building Code, or the Code Official, an approved UL listed Central
Station service in accordance with NFPA 72 shall monitor fire alarm systems to provide for the
immediate and automatic notification to the emergency communications center. Each initiating
device shall report an address point and an alpha/numeric descriptor showing location, type of
device and status including indication of normal, alarm, trouble and supervisory status, as
appropriate. Alpha/numeric descriptor shall be required to be reported to the emergency
communications center upon activation of alarm conditions as specified by the fire code official.
Exception: Monitoring by a supervising station is not required for:
1. Single- and multiple-station smoke alarms required by Section 907.2.11.
2. Smoke detectors in Group 1-3 occupancies.
3. Automatic sprinkler systems in one- and two-family dwellings
4. Fire alarm systems in one- and two-family dwellings
Section 907.7.4 Add a new section to read as follows: Device/Zone Map. An easily readable fire
alarm device and/ or zone map of the building shall be permanently mounted in or near the fire
alarm control panel and documentation cabinet showing the location of all initiating devices
when required by the fire code official.
Ordinance No.
Page 10
Section 907.11 Add a new section to read as follows: Approved hold open devices. When
installed in buildings that have a fire alarm system and/or sprinkler system, all approved hold
open devices shall release upon activation of a fire alarm and/or sprinkler water-flow activation.
Section 912.4.1 Delete the section and replace with: Locking fire department connection caps.
Locking fire department connection caps approved by the fire department are required for all
new construction that have a water-based fire protection system and existing structures that
have a water-based fire protection system shall be required immediately after conducting the
five-year obstruction and maintenance testing, or if one or more of the fire department caps are
missing.
Section 912.8 Add a section to read as follows: Fire Department Connection Height. The fire
department connection shall be located not less than 18 inches from the bottom of the cap(s)
and not more than 3 feet from the top of the cap(s) above the level of the adjacent grade or
access level. Deviation from this height may be granted by the Code Official for just cause.
Section 912.9 Add a section to read as follows: Size. Minimum fire department connection
(FDC) size shall be 2 1/2" National Standard Thread Siamese connection.
Section 1013.7 Add a new section to read as follows. Additional Exit Signs: Exit signs may be
required at the discretion of the code official to clarify an exit or exit access.
•
Section 1029.2 Add a second exception as follows:
Exception: The main entrance/exit of A-2 occupancies shall be of a width that
accommodates not less than two-thirds of the total occupant load.
Section 1031.2 Modify 1031.2 by deleting the exceptions and inserting in lieu thereof the following:
EXCEPTIONS:
1. The emergency escape and rescue opening is permitted to open onto a balcony within an atrium
in accordance with the requirements of Section 404 provided the balcony provides access to an exit
and the dwelling unit or sleeping room has a means of egress that is not open to the atrium.
2. Regardless of what Tables 1006.3.4(1) and 1006.3.4(2) allow, all group R-2 occupancies other than
hotels and motels must be provided with emergency escape &rescue openings.
3. Emergency escape and rescue openings are not required from basements or sleeping rooms
that have an exit door or exit access door that opens directly into a public way or to a yard, court or
exterior exit balcony that opens to a public way.
Section 5003.5 Add a sentence to the end of the section to read as follows: Signs shall also
comply with the requirements of the Iowa Right to Know law.
Section 5704.2.9 Add a sentence to the end of the section to read as follows: For aboveground
storage tanks of 276 gallons capacity or more, the minimum distance between such
aboveground tanks and any Residential Zone boundary must be at least 100 feet. If the
aboveground tank is located in an approved vault, the minimum separation distance from a
Residential Zone boundary may be reduced to no less than 50 feet.
Section 5704.2.11.1 Add a #4 to the end of the section to read as follows:
4. A minimum distance of ten (10) feet shall be maintained between underground tanks and
any Residential Zone boundary. •
Ordinance No.
Page 11
Section 5704.2.13.2.4 Add a section to read as follows: Existing above-ground tank hazards.
Existing above-ground tank installations, even if previously approved, that are determined to
constitute a hazard by the fire code official, shall not be continued in service. Unsafe tanks shall
be removed as required by the fire code official and in accordance with this code.
That the geographic limits referred to in certain sections of the 2021 International Fire Code are
hereby established as follows:
Section 5704.2.9.6.1. The storage of Class I and Class II liquids in above-ground tanks outside
of buildings is prohibited in the entire City of Iowa City, Iowa.
Exception: Zones I 1&2, CI 1 and/or as approved by the Fire Chief.
Section 5706.2.4.4. The storage of Class I and Class II liquids in above-ground tanks is
prohibited in the entire City of Iowa City, Iowa.
Exception: Zones 11&2, CI 1 and/or as approved by the Fire Chief.
Section 6104.2. The storage of liquefied petroleum gas is prohibited in the entire City of Iowa
City, Iowa.
Exception: Zones 11&2, CI 1 and/or as approved by the Fire Chief.
Section II. Repealer. All ordinances and parts of ordinances in conflict with the provisions of
this Ordinance are hereby repealed.
Section III. Severability. If any section, provision or part of the Ordinance shall be adjudged to
be invalid or unconstitutional, such adjudication shall not affect the validity of the Ordinance as a
whole or any section, provision or part thereof not adjudged invalid or unconstitutional.
Section IV. Effective Date. This Ordinance shall be in full force and effect after final passage,
approval and publication, as provided by law.
Passed and approved this day of , 2023.
Mayor
Attest:
City Clerk
Approved by:
G
City Attorn 's Office
(Sue Dulek— 05/30/2023)
Ordinance No.
Page 12
It was moved by and seconded by that the Ordinance as
read be adopted, and upon roll call there were:
Ayes: Nays: Absent:
Alter
Bergus
Dunn
Harmsen
Taylor
Teague
Thomas
First Consideration 06/06/2023
Vote for passage: AYES: Alter, Bergus, Dunn, Harmsen, Taylor, Teague, Thomas
NAYS: None ABSENT: None
Second Consideration
Vote for passage:
Date published